The weight of a dum bell is 500 n. It is lifted over a bodybuilder’s head at a distance of 0.7 meters. What is the work done by the bodybuilder on the dum bell?

350 J

714.2 J

500 J

1.4 x 10-3 J

To calculate the smallest value of v sufficient for a pendulum (with embedded mass m) to swing clear over the top of its arc, we need to first understand the equation of motion for the pendulum.

The equation of motion is given by:
v2 = g(L-x)sin θ
Where g is the acceleration due to gravity, L is the length of the pendulum, x is the amplitude, and θ is the angle of the pendulum.

To calculate the smallest value of v sufficient for the pendulum to swing clear over the top of its arc, we need to set θ equal to 90° and solve for v. This gives us:
v2 = g(L-x)sin 90°
v2 = g(L-x)
v = √(g(L-x))

Therefore, the smallest value of v necessary for the pendulum to swing clear over the top of its arc is equal to √(g(L-x)).

#SPJ11

to learn more about pendulum : https://brainly.com/question/15543716

The correct answer is a) 8. The number of revolutions made by the wheel is directly proportional to the angle through which it has turned.

Therefore, we can use the formula for the angle turned by an object with a constant angular acceleration as follows:

θ = ω₀t + 1/2 αt²

Where θ is the angle turned, ω₀ is the initial angular velocity (which is zero in this case), α is the angular acceleration, and t is the time elapsed.

We are given that the wheel has made 4 complete revolutions in 4 seconds, which is a total angle of 4*2π radians. Therefore, we can use this to find the angular acceleration as follows:

4*2π = 1/2 α(4)²

α = 4π/8 = π/2 radians per second squared

Now we can use the same formula to find the angle turned after 8 seconds:

θ = 0(8) + 1/2 (π/2)(8)² = 16π radians

The number of revolutions made by the wheel is equal to the angle turned divided by 2π, so we have:

Number of revolutions = 16π / 2π = 8

Therefore, the wheel has made 8 complete revolutions after 8 seconds.

For more details about revolutions click here:

https://brainly.com/question/29158976#

#SPJ11

Answer:

Incresing the staircase does not affect the work done; only the vertical distance affects the work done. Remember, the work is done against the weight and thus the relevant displacement is only the vertical displacement.

Explanation:

A plastic pipe 9 cm long has an outside radius of 3 cm and an inside radius of 2cm. if the density of the plastic is 0.82 g/cm,  the mass of the pipe  is 115.84 g.

To calculate the mass of the pipe, we need to find its volume and then multiply it by the density of the plastic. The volume of the pipe can be calculated as the  difference  between the volume of the outer cylinder and the inner cylinder:

volume of the pipe= volume of the outer cylinder- volume of the inner cylinder.Now the formula for the volume of a cylinder is:

Volume = π × r^2 × h, where r is the radius and h is the height of the cylinder.so  volume of the outer cyliner is = π × (3)^2 × 9 = 254.47 cm^3, volume of the inner cylinder= π × 2^2 × 9 = 113.10 cm^3, volume of the pipe =254.47 cm^3 - 113.1 = 141.37 cm^3.

Now we calculate the mass of the pipe by multiplying its volume by the density of the plastic:

Mass = Volume × Density = 141.37 cm^3 × 0.82 g/cm^3 = 115.84 g

To know more about mass refer to the link   brainly.com/question/19694949

#SPJ4

Different colors have different indices of refraction. This is known as dispersion, which is the separation of white light into its constituent colors as it passes through a prism. The prism does not contain narrow, equally spaced slits; instead, it is curved in order to separate light into its constituent colors.

The dispersion of light when it passes through a prism shows that different colors have different indices of refraction.The process in which white light separates into its constituent colors is known as dispersion. It is caused by the fact that different colors of light travel at different speeds in a material. Because the speed of light is lower in materials than it is in a vacuum, the amount by which the light is refracted (i.e., bent) is determined by the material's refractive index, which is a measure of the material's ability to refract light.

Dispersion can be illustrated by a prism. When white light passes through a prism, it is dispersed into its component colors, forming a spectrum. Red, orange, yellow, green, blue, indigo, and violet are the seven colors in this spectrum.A material's index of refraction is defined as the ratio of the speed of light in a vacuum to the speed of light in that material.

The higher the refractive index of a material, the slower light travels through it. Different colors of light are refracted (bent) to different degrees by a material due to this difference in speed, resulting in the dispersion of light. As a result, when white light is passed through a prism, it produces a spectrum of colors. Therefore, option (C) different colors have different indices of refraction

For more such questions on refraction

https://brainly.com/question/26655381

#SPJ11

The altitude of the satellite (in km) the moment it starts its descent is: (radius + (2 * pi * 2.8 km/s) / period)

The altitude of the satellite the moment it starts its descent depends on the radius of the planet and the speed of the satellite. To calculate the altitude, we need to first calculate the period of the satellite's orbit.

The period is calculated by taking the square root of (4 * pi2 * radius3) / (Gravitational Constant * mass), where G is the Gravitational Constant. Once we have the period, we can then calculate the altitude of the satellite the moment it starts its descent. This is done by taking the radius of the planet plus (2 * pi * speed) / period.

In this case, the altitude is (radius + (2 * pi * 2.8 km/s) / period). The satellite orbits the planet in an elliptical orbit, and its altitude is changing constantly, so the altitude will be different each time it passes the planet.

To know more about satellites refer here:

https://brainly.com/question/9266911#

#SPJ11

The transducer's ringing frequency is 1.731 kHz.
In a step test of a transducer, a signal has a damped oscillation that decays to a steady value. The period of oscillation is 0.577 ms.

The formula for the time period of oscillation is given by:T = (2π / ω)0.5,where T = time period and ω = angular frequency. From the above equation, the angular frequency is given as:ω = (2π / T)^2. The frequency of oscillation is given as:f = 1 / T. The formula for the damping ratio is given as:ζ = ln(A1/A2)/Tn, where A1 = amplitude of the first peak, A2 = amplitude of the second peak and Tn = time between peaks.

Substituting the values, we get:ζ = ln(0.707/0.707)/0.577ζ = 0. We know that the ringing frequency is given by:fr = f (1 - 2ζ^2)^0.5. Substituting the values, we get:fr = 1 / 0.577 x (1 - 2 x 0^2)^0.5fr = 1.731 kHz.

Learn more about period of oscillation:

https://brainly.com/question/22499336

#SPJ11

The velocity of the boat immediately after the child throws the package, assuming it was initially at rest, is 0.31 m/s.

The direction of motion of the package is positive, so we can take its velocity as positive.

m = 2.20 kg (mass of the package)v = 2.50 m/s (velocity of the package)

Final momentum of the system = mv

Final momentum of the system = 2.20 kg × 2.50 m/s

Final momentum of the system = 5.5 kgm/s

The mass of the child is 21.0 kg, and that of the boat is 45.0 kg.

Let the velocity of the boat immediately after the child throws the package be[tex]v_2[/tex].

[tex]m_1v_1 + m_2v_2 = mv[/tex]

where [tex]m_1[/tex] , [tex]v_1[/tex] and[tex]m_2[/tex] , [tex]v_2[/tex]  are the masses and velocities of the boat and child respectively, and m and v are the masses and velocities of the system after the event.

[tex]m_1[/tex] = 45.0 kg (mass of the boat)

[tex]m_2[/tex] = 21.0 kg (mass of the child)v1 = 0 (initial velocity of the boat)

[tex]v_2[/tex] = velocity of the boat after the child throws the package.

[tex]m = m_1 + m_2 = 45.0 kg + 21.0 kg = 66.0 kg

v_1 + v_2 = mv_2 = v − v_1v_2 = mv - v_1v_2 = (m_1v_1 + m_2v_2 - m_1v_1) / m[/tex]

Substituting the values we get:

[tex]v_2[/tex]= (45.0 kg × 0 + 21.0 kg × 5.5 kgm/s - 45.0 kg × 0) / 66.0 kg

[tex]v_2[/tex] = 0.31 m/s

Therefore, the velocity of the boat immediately after the child throws the package, assuming it was initially at rest, is 0.31 m/s.

To know more about Velocity refer here :

https://brainly.com/question/80295

#SPJ11

The right response is option (a). ECGs that are considered normal This P wave denotes either atrial contraction or depolarization. Ventricular depolarization or contraction is represented by the QRS complex.

3. Repolarization of the ventricles at the T wave.

When the atria don't beat in time with both the ventricles, the condition is known as atrial fibrillation.

• A lack of atrial activity might exist.

ECG in atrial fibrillation: The lack of "P" waves is the telltale indication of both the condition. Atrial activity is absent, which is the reason of this.

• The presence of aberrant fibrillary waves by place of the P waves implies abnormal atrial contraction.

• The P wave ought to be diminished or missing.

To know more about waves click here

brainly.com/question/30783512

#SPJ4

You threw a bowling ball with 453 n of force, the ball moves 23,654 mm before coming to a stop. The work did by you on the ball is: 10,731.962 n•m.

You did work on the ball when you threw it with 453 n of force. Work is calculated by multiplying the amount of force (in newtons) by the distance the object travels (in meters).

To solve for the work done, we must first convert the distance from mm to m: 23,654 mm = 23.654 m. Then, we can calculate the work done using the equation Work = Force x Distance, which gives us:

Work = 453 n x 23.654 m = 10,731.962 n•m.

The unit of measurement for work is the Newton meter (n•m). This means that when you threw the bowling ball with 453 n of force, you did 10,731.962 n•m of work on it.

To know more about force refer here:

https://brainly.com/question/26115859#

#SPJ11

You threw a bowling ball with 453 n of force, the ball moves 23,654 mm before coming to a stop. The work did by you on the ball is: 10,731.962 n•m.

The work done on the ball can be calculated using the formula:

Work = Force x Distance

where Force is the applied force on the ball and Distance is the distance over which the force is applied.

In this case, the force is 453 N and the distance is 23,654 mm. However, it is important to convert the distance from millimeters to meters, since the unit of force is in Newtons and the unit of distance should be in meters to maintain consistency in units.

Converting the distance from millimeters to meters:

23,654 mm = 23,654/1000 m = 23.654 m

Therefore, the work done on the ball is:

Work = Force x Distance

Work = 453 N x 23.654 m

Work = 10,742.962 J

Therefore, you did approximately 10,742.962 Joules of work on the ball.

For more details about work click here:

https://brainly.com/question/18094932#

#SPJ11

The replacement of a resistor by another resistor in a circuit will theoretically have the following effect on the circuit waveform at the output:

Explanation:

1. If the new resistor has the same resistance value as the original one, there will be no change in the output waveform.

2. If the new resistor has a higher resistance value than the original one, the output waveform amplitude may decrease, and the time constants associated with any RC (resistor-capacitor) or RL (resistor-inductor) components in the circuit may change, potentially altering the waveform shape or frequency response.

3. If the new resistor has a lower resistance value than the original one, the output waveform amplitude may increase, and the time constants associated with any RC or RL components in the circuit may change, potentially altering the waveform shape or frequency response.

In summary, replacing a resistor with another resistor may change the amplitude, shape, and frequency response of the circuit waveform at the output, depending on the new resistor's value in relation to the original one.

To know more about waveform shape here :

https://brainly.com/question/11429666

#SPJ11

Answer:

The  frictional force "opposes" the motion.

Thus the frictional force is to the left.

3). The wavelength of the laser light used is approximately 0.0000663 mm.

To determine the wavelength of the laser light, we can use the formula for the spacing between diffraction maxima from a diffraction grating:

dsinθ = mλ

where d is the spacing between the grating lines (in this case, 1/300 mm), θ is the angle between the incident beam and the diffracted beam (which can be calculated from the positions of the maxima and the distance from the grating to the screen), m is the order of the maximum, and λ is the wavelength of the light.

Since the problem mentions a first order maximum, we can use m = 1.

Therefore, the correct calculation to determine the wavelength of the laser light is:

λ = d*sinθ/m = (1/300 mm)*sin(θ)/1

We can use the diagram to measure the distance between the first order maximum and the central maximum, and the distance between the grating and the screen, in order to calculate sinθ:

sinθ = (distance between maxima)/(distance to screen)

sinθ = (0.40 m)/(2.00 m)

sinθ = 0.2

Substituting this value into the equation, we get:

λ = (1/300 mm)*sin(0.2) = 0.0000663 mm

Therefore, the wavelength of the laser light used is approximately 0.0000663 mm.

4). D. "Only transverse waves can be polarised" statement is correct about the waves.

Polarisation refers to the alignment of the oscillations of a wave in a particular direction. Transverse waves have oscillations that are perpendicular to the direction of wave propagation, and therefore they can be polarised by filtering out all but one orientation of oscillation. Longitudinal waves, on the other hand, have oscillations that are parallel to the direction of wave propagation, and therefore they cannot be polarised in the same way.

To know more about wavelength, visit:

https://brainly.com/question/13533093

#SPJ1

Conduction involves the transfer of heat through direct contact,
while radiation involves the transfer of heat through electromagnetic waves.

Conduction and radiation are two different mechanisms by which heat is transferred from one object to another.

Conduction is the transfer of heat through direct contact between two objects that are at different temperatures. When two objects are in contact, the hotter object transfers some of its heat energy to the cooler object until they reach thermal equilibrium. For example, when you touch a hot stove, heat is transferred from the stove to your hand through conduction.

Radiation is the transfer of heat through electromagnetic waves. Unlike conduction, radiation does not require direct contact between two objects. Instead, heat energy is transferred through the air or space between the two objects. For example, the sun warms the earth through radiation. Heat energy is transferred from the sun to the earth through electromagnetic waves, even though there is no physical contact between them.

80 N of force is used to propel a lawn mower. The issue is determining the overall distance the lawn mower was pushed after performing 12,000 J of work on a grass.

80 N of force is used to propel a lawn mower. When you mow a lawn, you put in 12,000 J of labour, D is Distance 150 Meters.

A system's heat gain or loss can be determined by multiplying the given mass by the substance's specific heat capacity and the temperature differential.

To determine: The total distance the lawnmower pushed

The lawnmower's work can be summed up as:

Here, "F" stands for force, "d" for displacement, and "∅" represents the angle between the two.

The angle is 0° while pulling the lawnmower

W⇒F×d×cos(0°)

  ⇒F×d

  ⇒=80×150

  ⇒12000

W⇒12000J

Displacement, which in this context is equivalent with distance, is 150 meter's. Due to the rule of conservation of energy, we know that the reaction that heated the surroundings must have produced the energy, which means that the reaction caused the wood to lose 12000J when it burned with oxygen.

Learn more about Lawn mower here

https://brainly.com/question/25987774

#SPJ1

The wire is insulated with a layer of plastic or paint around the outside when wound into a coil to form an electromagnet to prevent the wire from shorting out against itself or other conductive materials.

When an electric current flows through a wire, it generates a magnetic field around the wire. By coiling the wire, the magnetic field is strengthened, creating a more powerful electromagnet.

However, if the wire is not insulated, the coils can touch each other, creating a short circuit that can damage the wire or the power source. Insulating the wire with a layer of plastic or paint prevents this from happening by creating a barrier between the wire and other conductive materials.

This allows the electric current to flow through the wire and generate the magnetic field, while also protecting the wire and ensuring that the electromagnet works properly.

​

Read more about electromagnet

brainly.com/question/12555869

#SPJ1

A 3.5 L container of oxygen gas kept at 6 °C and 0.5 atm pressure has a total translational kinetic energy of about 375.5 J.

By adding the two types of kinetic energy, it is possible to calculate the object's total kinetic energy. Remember that the product of the object's mass and the square of its linear velocity (around its centre of mass) and dividing the result by two gives the object's translational kinetic energy.

KE = (3/2) * nRT

PV = nRT

where P is the pressure, V is the volume, and the other variables are the same as in the kinetic energy formula.

n = PV / RT

Substituting the given values, we get:

n = (0.5 atm) * (3.5 L) / [(0.08206 L·atm/mol·K) * (6 + 273.15 K)]

n ≈ 0.0671 mol

KE = (3/2) * nRT

Substituting the given values and the number of moles we just calculated, we get:

KE = (3/2) * (0.0671 mol) * (0.08206 L·atm/mol·K) * (6 + 273.15 K)

KE ≈ 375.5 J

To know more about kinetic energy visit:-

https://brainly.com/question/26472013

#SPJ1

The force is removed after the box travels a certain distance until it comes to a stop. The distance the box travels before coming to a stop is known as the stopping distance. What is the mass, speed, and coefficient of kinetic friction between the box and the surface?

Mass = 11.6 kg Speed = 3.00 m/s Coefficient of kinetic friction = 0.22Force is required to maintain a constant speed, and the force is equal to the force of friction. So, F = frictional force Frictional force = F = μkNWhere,μk is the coefficient of kinetic friction N is the normal force. The normal force, N = m g where, m is the mass of the box g is the acceleration due to gravity g = 9.81 m/s²So, the frictional force F is given by; F = μkN = μk × m × g Now, F = 0.22 × 11.6 × 9.81 = 25.578 N The force required to move the box is 25.578 N.

The force is removed after the box travels a certain distance until it comes to a stop. The distance the box travels before coming to a stop is known as the stopping distance. The stopping distance can be calculated using the formula; d = (v²/2μk g)where, v is the speed of the object before it comes to a stopμk is the coefficient of kinetic friction g is the acceleration due to gravity g = 9.81 m/s²The stopping distance is, d = (v²/2μk g) Substituting the given values in the above equation, we get; d = [(3.00 m/s)² / (2 × 0.22 × 9.81 m/s²)] = 2.38 m

Therefore, the box slides for 2.38 m before coming to rest.

Learn more about how far does the box at: brainly.com/question/14704175

#SPJ11

By following these steps, you will find the hydrostatic force acting against the horizontal square at the bottom of the 3ft pool with the given liquid density.

To calculate the hydrostatic force against a horizontal square (2ft x 2ft) at the bottom of a 3ft pool, you can follow these steps:
Step 1: Find the pressure at the bottom of the pool.
Hydrostatic pressure (P) can be calculated using the formula:
P = ρgh
where ρ (rho) is the liquid density, g is the acceleration due to gravity (32.2 ft/s²), and h is the depth of the pool (3ft).
Step 2: Calculate the hydrostatic pressure.
Use the given liquid density (ρ) and plug in the values into the formula:
P = ρ * 32.2 * 3
Step 3: Find the area of the horizontal square.
Area (A) = length × width = 2ft × 2ft = 4ft²
Step 4: Calculate the hydrostatic force.
Hydrostatic force (F) can be calculated using the formula:
F = PA
Substitute the calculated pressure (P) and area (A) into the formula:
F = P * 4
By following these steps, you will find the hydrostatic force acting against the horizontal square at the bottom of the 3ft pool with the given liquid density.

For similar question on hydrostatic.

https://brainly.com/question/124508\

#SPJ11

The power output of the weightlifter is 10,000 Watts.

The power output of a weightlifter lifting a 2,000 Newton weight a vertical distance of 0.5 meters in 0.1 seconds can be calculated using the following formula:

Power = Work/Time = (Force x Distance)/Time

In this case: Power = (2,000 N x 0.5 m)/0.1 s = 10,000 W (Watts)

Power is defined as the work done in a unit of time.

Learn more about power:

https://brainly.com/question/1634438

#SPJ11

Answer: B.  Plantae, Protista, Fungi, Animalia

Explanation: It became very difficult to group some living things into one or the other, so early in the past century the two kingdoms were expanded into five kingdoms: Protista (the single-celled eukaryotes); Fungi (fungus and related organisms); Plantae (the plants); Animalia (the animals); Monera (the prokaryotes).

Brainliest? <33

The correct order of kingdoms for organisms 1 through 4 is Plantae, Fungi, Protista, and Animalia. The correct option is D.

In biology, a kingdom is a basic classification of organisms into a group based on certain characteristics. Traditionally, there were five kingdoms: Monera (single-celled prokaryotes), Protista (single-celled eukaryotes), Fungi (multi-celled organisms that feed on decaying matter), Plantae (multi-celled organisms that make their own food through photosynthesis), and Animalia (multi-celled organisms that feed on other organisms).

However, with advancements in molecular biology and genetics, the classification system has been revised and some scientists have proposed a three-domain system that includes Archaea (single-celled organisms that thrive in extreme environments), Bacteria (single-celled organisms found everywhere), and Eukarya (organisms with cells containing a nucleus).

The exact classification system can vary depending on the taxonomist or scientist and the organisms being studied. The goal of classification is to organize organisms into groups based on shared characteristics to better understand the diversity of life on Earth.

Here in the Question,

The order in which Felicia should list the kingdoms for organisms 1 through 4 is:

1. Plantae: This organism is multicellular and has cells with cell walls. It also makes its own food, which is a characteristic of the Plantae kingdom.

2. Fungi: This organism is a single-celled decomposer, which is a characteristic of the Fungi kingdom.

3. Protista: This organism is a simple multicellular organism that lacks true tissues and organs but makes its own food, which is a characteristic of the Plantae kingdom.

4. Animalia: This organism is multicellular and gets food by eating other organisms, which is a characteristic of the Animalia kingdom.

Therefore, the correct order of kingdoms for organisms 1 through 4 is D. Plantae, Fungi, Protista, and Animalia.

To learn more about  taxonomy in biology click:

https://brainly.com/question/30638139

#SPJ2

The tension that a rope must withstand if it is used to accelerate a 1810-kg car horizontally along a frictionless surface at 1.20 m/s² is 21900 N.

The question is asking for the amount of tension that the rope should have to accelerate a 1810-kg car horizontally along a frictionless surface at a speed of 1.20 m/s².

Tension (T) = mass (m) x acceleration (a)

Using the given values:

T = (1810 kg) x (1.20 m/s²)T = 21900 N

Therefore, the tension that a rope must withstand if it is used to accelerate a 1810-kg car horizontally along a frictionless surface at 1.20 m/s² is 21900 N.

Here you can learn more about The tension

https://brainly.com/question/30620986#

#SPJ11  

Currently, wind power generates a greater overall share of electricity than solar does. Solar energy is a far more practical choice for households.

To know more about electricity

https://brainly.com/question/27960851

#SPJ4

The painter will be able to catch the can if it falls off a ledge and passes in front of him, given that he has lightning-fast reflexes.

What we know: The distance between the can and the ground is 2.25 m.
The distance between the painter’s hands and the can is 4.45 m.
To solve this problem, we need to use the following equation: s = ut + 1/2 at²
Where:s is the distance traveled by the can is the initial velocity (0)m/sa is the acceleration due to gravity (-9.81)m/st is the time taken for the can to fall

Let’s start by calculating the time taken for the can to fall: s = ut + 1/2 at²2.25 = 0t + 1/2(-9.81)t²4.905t² = 2.25t = sqrt(2.25/4.905) = 0.67 seconds
Now, we can calculate the distance traveled by the can horizontally in 0.67 seconds:
distance = speed × time
The speed of the can is the same as the speed of the painter's hands, so let's call it v:distance = v × 0.67
We don't know what v is yet, but we can find it using the fact that the painter's hands are 4.45 m above the can when it falls:v = sqrt(2gh)
where g is the acceleration due to gravity (9.81 m/s²) and h is the distance between the painter’s hands and the can (4.45 m):v = sqrt(2 × 9.81 × 4.45) = 9.90 m/s

Finally, we can calculate the distance the can travels horizontally: d = v × t = 9.90 × 0.67 = 6.63 m
The horizontal distance the can travels is 6.63 m, which is greater than the distance between the painter and the wall.

Therefore, if the can falls off the ledge and passes in front of him, the painter will be able to catch it if he has lightning-fast reflexes.

To know more about "Acceleration due to gravity" refer here:

https://brainly.com/question/11873969#

#SPJ11

The initial impulse of the baseball was 7.37 N-s when thrown at 62.5 mph. After the batter improved his follow-through, the impulse increased by 13.0%, resulting in a new speed of the ball leaving the bat of approximately 39.1 m/s.

The impulse of an object is equal to the force applied to it multiplied by the time for which the force acts. In the case of a baseball being hit by a bat, the impulse is what causes the ball to accelerate and leave the bat. The initial impulse of the baseball was 7.37 N-s when thrown at 62.5 mph. However, the batter improved his follow-through, resulting in a 13.0% increase in the impulse applied to the ball. This increase in impulse caused the ball to leave the bat with a higher velocity, which can be calculated using the formula for impulse and the mass of the baseball. The new speed of the ball leaving the bat is approximately 39.1 m/s, which is a significant improvement from the initial speed.

learn more about impulse here:

https://brainly.com/question/2193212

#SPJ4

When motors, heavy machinery, and fluorescent lights interfere with a signal, it is known as Electromagnetic interference (EMI).

What is Electromagnetic interference (EMI):

Electromagnetic interference (EMI) is a phenomenon that happens when electrical equipment, machines, or other electrical systems produce electromagnetic energy that interacts with other electronic devices or machinery, resulting in electrical signals known as noise.

As a result, electronic gadgets may suffer from Electromagnetic interference (EMI).

When motors, heavy machinery, and fluorescent lights interfere with a signal, it is known as Electromagnetic interference (EMI).

When EMI is produced in electrical equipment, it may reduce its capacity to communicate with other devices by making signals less strong or understandable.

To reduce EMI's effects, shielding and filtering techniques are often used.

For similar question on interference.

https://brainly.com/question/2166481

#SPJ11

According to the text, jupiter has a central pressure of 100 million bars, while earth has a central pressure of 4 million bars. Therefore, the pressure at the center of Jupiter is 25 times greater than that of the Earth.

Below are detailed explanations on Jupiter's pressure, Earth's pressure and how many times more pressure exists in the center of Jupiter compared to that of Earth.

Pressure of Jupiter: Jupiter is known for having the largest and strongest magnetic field among all the planets in the solar system. According to research, Jupiter’s central pressure can go up to 100 million bars. The pressure at Jupiter's core is around 4,000,000 atmospheres. This central pressure is what sustains the fusion process.

Pressure of Earth: Earth is composed of several layers, with the innermost layer being the core. The pressure at the center of the Earth is around 4 million bars. This is because the Earth is much smaller than Jupiter and has much less mass. This pressure is still much greater than the pressure that we experience at the surface.

How many times more pressure exists in the center of Jupiter compared to that of Earth?The pressure at the center of Jupiter is 25 times greater than that of the Earth.

We can calculate this as follows: Pressure in Jupiter's center = 100 million bars

Pressure in Earth's center = 4 million bars

Therefore, Pressure in Jupiter's center ÷ Pressure in Earth's center = 100 million bars ÷ 4 million bars = 25 times greater pressure exists in the center of Jupiter compared to that of Earth.

To learn more about pressure refer to: brainly.com/question/28012687

#SPJ11

The frequency of your friend's trombone musical instrument is 353.3 Hz.

When two musical instruments are being played together as a duet or ensemble, it is critical that they be in tune. One instrument is used as a reference for the other, and any necessary adjustments are made based on the reference instrument's pitch. In this case, the reference instrument is the student's trombone, which produces a tone at 350 Hz. The friend's trombone is not perfectly in tune with the reference instrument, which causes a beat frequency to be heard.

To determine the frequency of the friend's trombone, we can use the formula:f1 - f2 = n * B, where f1 and f2 are the frequencies of the two instruments, n is the number of beats per second, and B is the beat frequency. In this case, n = 3 beats per 3 seconds, which is equivalent to 1 beat per second, or 1 Hz. The beat frequency B is therefore 1 Hz. We can rearrange the formula to solve for f2:f2 = f1 - n * B

Substituting the known values, we get:f2 = 350 Hz - 1 Hz = 349 Hz. However, we are told that the student's ear is good enough to detect that the friend's trombone is at a higher frequency. This means that the friend's trombone is actually slightly sharper than the reference instrument. To find the exact frequency, we can use the fact that the beat frequency is caused by the difference in frequency between the two instruments.

Since we are hearing 3 beats per 3 seconds, the difference in frequency must be 3 Hz. Therefore, the frequency of the friend's trombone is:f2 = f1 + B = 350 Hz + 3 Hz = 353 Hz. To round to at least 1 decimal place, we can write:f2 = 353.3 Hz

To know more about musical instrument, refer here:

https://brainly.com/question/16191430#

#SPJ11

When a person moves away from a stationary sound source, the phrase that describes: the sound perceived by the person is the pitch of the sound that will decrease.

A person moves away from a stationary sound source; the pitch of the sound perceived by the person will decrease. This happens because the pitch is the frequency of the sound. The pitch of the sound produced by a source of sound is the number of sound waves produced per second.

The number of sound waves arriving per second at a person's ear when he moves away from the sound source is reduced, resulting in a decrease in pitch, and a change in frequency of the sound.

To know more about "Stationary sound" refer here:

https://brainly.com/question/9753152#

#SPJ11