Answer:
The answer is B (default).
The gear lube level is being checked in a manual transmission. Technician A says it should run out when the plug is removed. Technician B says that some transmissions use motor oil as gear lube. Who is correct?
Answer:
Both technician A and B are correct
Explanation:
The function of the gear lube drain plug is to drain the automatic transmission fluid from the gear box
Although motor oil is for the engine, motor vehicle transmission uses different oil types as the transmission system or automatic transmission system (ATF) operates in an closed system environment it is free from fuel contamination that motor oil absorbs
As such depending on the specification, manual transmission oil can range from hypoid oil, motor oil or automatic transmission oil.
Which of the combinations below has the greatest impact in increasing the potential for vapor drift? A. Low temperature, low humidity B. Moderate temperature, high humidity C. High temperature, low humidity
Answer: C
Explanation:
Vapour drift can take place when the substance or liquid evaporates. Volitile substance will evaporate more rapidly than non - volatile substance
Increase in temperature on substance make it lighter and float rapidly. Also, substance of high humidity will have more weight or density than the substance of low humidity.
The combinations that has the greatest impact in increasing the potential for vapor drift is
High temperature, low humidity which is option C
Royce has a Bevel protractor with a damaged vernier scale. What limitation will Royce face if he uses this protractor to measure angles?
Answer:
Limitation in the level of possible accuracy of the that can be obtained to mainly whole degrees
Explanation:
The angle measurement values are located around the circularly shaped bevel protractor to which a Vernier scale can be attached to increase the accuracy of the angle measurement reading
The accuracy of the bevel protractor is up to 5 arc minutes or 1/12° with the space on the Vernier scale having graduations of 1/12°, such that two spaces on the main scale is 5 arc minutes more than a space on the Vernier scale and the dimensions of the coincidence of the two scale will have an accuracy of up to 1/12°
Therefore, whereby the Vernier scale is damaged, the accuracy will be limited to the accuracy main scale reading in whole degrees.
2.
A _yellow line means traffic on either side may cross the
center line to pass another vehicle.
A. single solid
B. double solid
C. single broken
D. double broken
What’s the answer?
Answer:
A. Single broken
Hope this is correct
HAVE A GOOD DAY!
A 30.0 W light bulb in a simple DC circuit is powered by a 9.0 V battery. Assuming there are no other circuit elements, how much current flows through the lightbulb?
2. Technician A says that checking ambient temperature as part of an AC performance test is unnecessary. Technician B says that if the AC compressor hasn't
been operating, the high-side pressure should be high and the low-side pressure should be low. Who is correct?
O A. Technician A
O B. Neither Technician A nor B
O C. Technician B
O D. Both Technicians A and B
Answer:
The correct option is;
B. Neither Technician A nor B
Explanation:
A performance test is meant to determine the proper functioning of the air conditioning system for fault finding where repair is required
While the engine is powered off it is expected that to have the same pressure or equal pressures in the low-side and high-side pressure and have a pressure expected for a given ambient temperature, such that, as an example, a system with R134a should have a pressure slightly more than 71 psi. at 70°F
Therefore, neither technicians A nor B is correct as the ambient temperature is important for performance testing and high-side and low-side pressures should be equal when the engine is powered off.
Harvey works in a metal industry and is working on sheet metal. Which of the following process are used in sheet metal
Bending
Rolling
Deep Drawing
Forging
Punching
Extrusion
Answer:
The processes used in sheet metals includes;
Bending
Rolling
Punching
Deep drawing
Explanation:
Sheet metal are thin flat pieces of metals produced by industrial forming processes. Sheet metal working is the fabrication and manufacturing of everyday metallic goods, components and equipment parts that are metallic. The metal working processes includes cutting, welding, bending punching, rolling and forming
The thickness of sheet metal varies from thin foils to plate steel and structural steel.
Answer:
click the picture for the correct answer
Bending. punching. deep drawing
Dimensioning a drawing means
Answer:
Dimensioning a drawing refers to drawing a dimension for every side of the figure. It means to write the lengths of every side in the figure(2D or 3D)
Hope it helps <3
answer this question fast
Answer:
When the expenditure increased, then the consumer's expenditure is increased to Rs.150 and when the price falls of the good it becomes Rs.5. Then, Good X will be Rs.10.
last question:If the Good X falls by 20%, then, it will be Rs.2, and according to his demand 100 units will be equal to Rs.200.
cause if one unit=rs.2, then 100units=100×2=200.
which of the following is not one of the common types of traction loss?
A. ROLL
B. YAW
C. PITCH
D. FORWARD
Answer: Forward So it's D
Answer:
It's forward :)
Explanation:
Please what is the name of this tool
Answer: it’s called a saw or see saw
Explanation: it works by cutting a tree, wood, tile, etc.
Could an able-bodied person receiving all or most of their income from government transfer payments achieve earned success? Why or why not?
Answer:
yes and no because if he transferred he has a major reason for doing so but if he doesn't its his own piece of cake and another reason why he transferred is to protect and keep his money and account and belongs safe
BHE:FLI:JPM next sequence
Answer:
NTQ
Explanation:
The given sequence is
BHE : FLI : JPM
If is clear that, alphabets on first places are B, F, J. Difference between their place vales is 4.
B+4=F,F+4=J ; so alphabet on first place of next term of sequence is J+4=N.
Similarly, alphabets on second places are H, L, P. Difference between their place vales is 4.
H+4=L,L+4=P ; so alphabet on second place of next term of sequence is P+4=T.
Alphabets on third places are E, I, M. Difference between their place vales is 4.
E+4=I,I+4=M ; so alphabet on third place of next term of sequence is M+4=Q.
Therefore, the next term is NTQ.
Two technicians are discussing cylinder- testing. Technician A says that when testing the power level of a specific cylinder using a Power balance test, it's best to ground it's secondart current. Technician B says that it's best to disconnect one spark plugs wire at a time to test cylinder power levels. Who is correct?
Answer:
Technician B is the answer
When a traffic officer directs you proceed through the intersection
when the red light is visible, you should:
Treat as a stop sign and then proceed forward.
Come to a stop and wait for the light to turn green.
Stop until the light changes to yellow.
Follow the officer's instructions and proceed through the
intersection with caution.
Answer:
You should follow the officer's instruction and proceed with caution
Explanation:
You should always follow the lawful orders of an officer regardless of standard traffic procedures. This is typical because the officer needed to take control of a particular situation due to a crash or other potential hazard, making manual commands safer than standard road rules.
If both the low-side and the high-side pressures are low, which of these could be the cause?
A. High refrigerant charge
B. Defective cooling fan
C. Low refrigerant charge
D. TXV. stuck open
Answer:
The correct option is;
C. Low refrigerant charge
Explanation:
Where both the low-side and the high-side pressure are low the refrigerant is low which may be as a result of a leak
When there is a low refrigerant charge there will be a larger range over which to compress the refrigerant increasing the work required and thus the heat in the system and the due to insufficient refrigerant, the entire system is under served and the evaporator super-heats due to lack of refrigerant
The liquid-line, the TVX evaporator and compressor will see less fluid flow and hence lesser pressures on the low-side and high-side of the refrigeration system.
Which sentence would make the best thesis statement?
Giraffes are tall, interesting animals.
Flamingos are pink birds that eat with their heads upside down.
Although insects are thought of as pests, they perform several vital functions in our ecosystems.
The peregrine falcon of North America is the fastest known bird, with diving speeds of over 250 mph.
Answer:C
Explanation:
Trust me (づ｡◕‿‿◕｡)づ
Answer:
C.
Explanation:
Got it right on Edge
Note that common skills are listed toward the top and less common skills are listed toward the bottom. According to O*NET, what are some common skills Electrical Engineers need? Check all that apply.
Answer:
Problem-solving skills. Regardless of their discipline, engineers are, at their core, problem solvers. ...
Critical thinking skills. ...
Basic circuit knowledge. ...
Enthusiasm for learning. ...
Communication skills. ...
Organisational skills. ...
Numerical skills. ...
Creative thinking skills
When adjusting your side mirrors, the horizon should be _______ the mirror. A. above the center of B. across the center of C. below the center of D. directly behind
Answer:
B. ACROSS THE CENTER OF
Trust me I've seen this before
Hope this is correct
HAVE A GOOD DAY!
Answer:
B, across the center
Explanation:
Am I the only one who cannot see the answers?? Does anybody know how to solve this?
Answer:
no, it seems that everyone is having the same issue. If you use the app you can still find the answers and see them.
Explanation:
In the event of a crash, Personal Injury Protection (PIP) coverage pays toward the medical costs for _____.
A. any injuries you cause to others
B. any injuries that are not your fault
C. your injuries if you are not at fault
D. your injuries, regardless of who's at fault
Answer:
The answer is D. Your injuries, regardless of who's at fault.
A clutch is chattering. Technician A says that uneven wear on the flywheel could be the cause. Technician B says that worn or broken motor mounts could be the cause. Who is correct? Group of answer choices
Answer:
Both Technician A and B are correct
Explanation:
Due to a contamination of the clutch disc friction surface, the clutch chatters
The contamination that causes clutch chattering includes
1) Worn or broken motor mounts
2) Bell housing bolts becoming loose
3) Clutch link damage
4) Warped flywheel, due to overheating, the flywheel can become warped such that the non uniform surface interfaces the clutch resulting in clutch chattering
5) Engine or transmission oil contaminating the disc.
Chemical resistant aprons for use while working around pesticides should.? A. Be made of solvent resistant leather B. Cover the body from chest to boots C. Be worn when anticipate that spray drift will substantially wet your clothing
Answer:
B. Cover the body from chest to boots
Explanation:
Respiratory Protective Equipment (RPE) may be required when handling dusts, fogs, smokes or vapours. It may also be needed for spraying using vehicles without an enclosed cab or hand spraying in enclosed spaces or above waist height.
Always refill your gas tank well before____.
Answer:
indicator light appears
Explanation:
indicator light appears
Answer:
Your fuel gauge reaches one quarter full
Hope this is correctHAVE A GOOD DAY!
the ____ method is the safest turning technique to use as it does not expose your hands to the airbags deployment area
Answer:
Push/pull Method
Explanation:
Push/pull method is seen as the best method to use when a driver what to steer a wheel to point the car in a particular direction reason been that PUSH/PULL method enables the driver to sit perfectly well in order to firmly hold the wheel which is why this method is often recommended as the safest and most effective way of steering than other steering method.
Therefore the PUSH/PULL method is the safest and the best turning technique to use because it does not expose the driver hands to the airbags area reason been that air bag are sometimes place in the centre of the steering wheel which means that when a driver cross his/her arms when steering will block the air bag in a situation where the air bag needed to explode out because airbag can explodes out with a lot of force which in turn could force the driver arms towards his/ her face which is dangerous.
Air enters a 28-cm diameter pipe steadily at 200 kPaand 208C with a velocity of 5 m/s. Air is heated as it flows, and leaves the pipe at 180 kPa and 408C. Determine (a) the volume flow rate of air at the inlet, (b) the mass flow rate of air, and(c) the velocity and volume flow rate at the exit.
Answer:
(a) [tex]\dot V_1[/tex] = 0.308 m³/s
(b) [tex]\dot m[/tex] = 0.732 kg/m³
(c) v₂ = 5.94 m/s.
Explanation:
(a) The volume flow rate is given by the cross sectional area of the pipe × Velocity of flow of air
Diameter of pipe = 28 cm = 0.28 m
The cross sectional area, A, of the pipe = 0.28²/4×π = 0.0616 m²
Volume flow rate = 5 × 0.0616 = 0.308 m³/s
[tex]\dot V_1[/tex] = 0.308 m³/s
(b) From the general gas equation, we have;
p₁v₁ = RT₁ which gives;
p₁/ρ₁ = RT₁
ρ₁ = p₁/(RT₁)
Where:
ρ₁ = Density of the air
p₁ = 200 kPa
T₁ = 20 C =
R = 0.287 kPa·m³/(kg·K)
ρ₁ = 200/(0.287 ×293.15) = 2.377 kg/m³
The mass flow rate = Volume flow rate × Density
The mass flow rate, [tex]\dot m[/tex] = 2.377×0.308 = 0.732 kg/m³
[tex]\dot m[/tex] = 0.732 kg/m³
(c) The density at exit, ρ₂, is found from the the universal gas equation as follows;
ρ₂ = p₂/(RT₂)
Where:
p₂ = Pressure at exit = 180 kPa
T₂ = Exit temperature = 40°C = 273.15 + 40 = 313.15 K
∴ ρ₂ = 180/(0.287×313.15) = 2.003 kg/m³
[tex]\dot m[/tex] = ρ₂×[tex]\dot V_2[/tex]
[tex]\dot V_2[/tex] = [tex]\dot m[/tex]/ρ₂ = 0.732/2.003 = 0.366 m³/s
[tex]\dot V_2[/tex] = v₂ × A
v₂ = [tex]\dot V_2[/tex]/A = 0.366/0.0616 = 5.94 m/s.
v₂ = 5.94 m/s.
Mike has a factory that manufactures highly customized products. Which type of manufacturing system is most suitable for it?
Answer:
Custom Manufacturing System.
Explanation:
As per the custom manufacturing system, each object is made by a unit of a producer like a craftsman or a group who works entirely on the concerned product. This manufacturing system is characterized by the use of machines and they appear to be highly skilled in their tasks and can not generate more than one object at a time. This also appears to be correlated with both the highest quality goods and the lowest volume efficiency.
Answer:
A. Conventional job shop
The structure of a house is such that it loses heat ata rate of 3800 kJ/h per8C difference between the indoors andoutdoors. A heat pump that requires a power input of 4 kWis used to maintain this house at 248C. Determine the lowestoutdoor temperature for which the heat pump can meet theheating requirements of this house.
Answer:
The lowest outdoor temperature for which the heat pump can meet the requirement of the house is -9.6°C
Explanation:
The coefficient of performance of a heat pump, COP, is given by the relation;
[tex]COP_{hp} = \dfrac{T_2}{T_2 - T_1} = \dfrac{Q_1\times (T_2 - T_1)}{\Sigma W}[/tex]
The rate of heat loss [tex]\dot Q_1[/tex] = 3800 kJ/h = 3800 ×1/60 × 1/60 kJ/s = 1.06 kJ/s
The power input = 4 kW = 4 kJ/s
The temperature indoors = 24 + 273.15 = 297.15 K
Therefore, we have;
[tex]COP_{hp} = \dfrac{297.15}{297.15- T_1} = \dfrac{1.06 \times (297.15- T_1)}{4}[/tex]
4×297.15= (297.15- T₁) × 1.06×(297.15- T₁)
Which gives;
18/19·T₁²-627.32·T₁+92014.97=0
(T₁ -263.59)·(T₁ - 330.71) = 0
The solutions are;
T₁ = 263.59 K or T₁ = 330.71 K
The lowest temperature = 263.59 K which is -9.6°C
The lowest temperature = -9.6°C.