Several weather variables are used to measure weather conditions. Identify 3 weather variables and their instruments that you would use to observe and collect data to determine the relationship between air mass movements and changes in weather.

The tests that can be used to determine the kinds of solids that have been listed are shown below.

Here are some tests that can be used to show that a solid is:

Ionic (NaCl):

Solubility test: NaCl is highly soluble in water, and a high degree of solubility can confirm the ionic nature of NaCl.

Conductivity test: In its molten or dissolved state, NaCl conducts electricity due to the presence of charged ions.

Metallic (Ca):

Conductivity test: Metals such as Ca conduct electricity due to the presence of free electrons in their crystal structure.

Ductility and malleability test: Metals are ductile and malleable, and can be easily deformed under pressure.

Covalent Network (Quartz, SiO2):

Hardness test: Covalent network solids such as quartz are extremely hard due to the strong covalent bonds between atoms.

Melting point test: Covalent network solids often have high melting and boiling points due to the strong intermolecular forces between atoms.

Polar Molecular (sugar, C6H12O6):

Solubility test: Polar molecules such as sugar are soluble in polar solvents such as water but insoluble in nonpolar solvents.

Melting and boiling point test: Polar molecular solids have lower melting and boiling points compared to ionic or covalent network solids due to weaker intermolecular forces.

Learn more about ionic solids:https://brainly.com/question/15241125

#SPJ1

The molarity of a solution made by dissolving 75 g of Epsom salt in 2.3 liters of solution would be 0.27 M.

The first step in calculating the molarity of the solution is to determine the number of moles of MgSO4 dissolved in 2.3 liters of solution.

The molar mass of MgSO4 is:

24.31 g/mol (for Mg) + 32.06 g/mol (for S) + 4x16.00 g/mol (for 4 O) = 120.37 g/mol

The number of moles of MgSO4 can be calculated using the formula:

moles = mass / molar mass

moles = 75 g / 120.37 g/mol = 0.623 moles

Next, we need to calculate the molarity (M) of the solution, which is defined as the number of moles of solute (MgSO4) per liter of solution:

Molarity = moles of solute / liters of solution

Molarity = 0.623 moles / 2.3 L = 0.27 M

Therefore, the molarity of the solution made by dissolving 75 g of Epsom salt (MgSO4) in 2.3 Liters of solution is 0.27 M.

More on molarity can be found here: https://brainly.com/question/2817451

#SPJ1

The mass of water, H₂O produced by the reaction of 1.06 grams of oxygen gas, O₂ is 0.72 grams

The mass of water, H₂O produced by the reaction of 1.06 grams of oxygen gas, O₂ can be obtained as shown below:

The balanced equation for the reaction is given below

4NH₃ + 5O₂ -> 4NO + 6H₂O

From the balanced equation above,

160 g of oxygen gas, O₂ reacted to produce 108 g of water, H₂O

Therefore,

1.06 g of oxygen gas, O₂ will react to produce = (1.06 × 108) / 160 = 0.72 g of water, H₂O

Thus, the mass of water, H₂O produced from the reaction is 0.72 g

Learn more about mass produced:

https://brainly.com/question/9526265

#SPJ1

4.69 g of oxygen gas is consumed by the reaction of 2.0 g of ammonia.

What is Atomic Mass?

Atomic mass is the mass of an atom of a chemical element, expressed in atomic mass units (amu). It is a measure of the total number of protons and neutrons in the nucleus of an atom. The atomic mass is usually given relative to the mass of a carbon-12 atom, which is assigned a mass of exactly 12 atomic mass units.

The balanced chemical equation for the reaction is:

4NH3 + 5O2 → 4NO + 6H2O

From the equation, we can see that 4 moles of NH3 reacts with 5 moles of O2. We need to determine how many moles of NH3 we have, and then use the mole ratio to calculate the number of moles of O2 needed.

First, we calculate the number of moles of NH3:

moles of NH3 = mass of NH3 / molar mass of NH3

moles of NH3 = 2.0 g / 17.03 g/mol (molar mass of NH3)

moles of NH3 = 0.1174 mol

Now we use the mole ratio from the balanced chemical equation to calculate the number of moles of O2:

moles of O2 = (5/4) x moles of NH3

moles of O2 = (5/4) x 0.1174 mol

moles of O2 = 0.1468 mol

Finally, we can use the number of moles of O2 to calculate the mass of O2 consumed:

mass of O2 = moles of O2 x molar mass of O2

mass of O2 = 0.1468 mol x 32.00 g/mol (molar mass of O2)

mass of O2 = 4.69 g

Learn more about Atomic Mass from given link

https://brainly.com/question/3187640

#SPJ1

Given that we don't have the equation mentioned in the question, I will assume that the equation is referred to is the following:

2N2(g) + 5O2(g) → 2N2O5(g)

a) If you start with 2 moles of O2, according to the equation, 5 moles of O2 are needed to react with 2 moles of N2. Therefore, the number of moles of N2O5 created would be (2/5) x 2 = 0.8 moles.

b) If you start with 1 mole of O2, according to the equation, 5/2 moles of O2 are needed to react with 2 moles of N2. Therefore, the number of moles of N2O5 created would be (1/(5/2)) x 2 = 0.4 moles.

c) If you start with 1 mole of N2, according to the equation, 5/2 moles of O2 are needed to react with 2 moles of N2. Therefore, the number of moles of N2O5 created would be (5/2) x 1 = 2.5 moles.

d) If you get 6 moles of N2O5 during your reaction, according to the equation, 2 moles of N2O5 are produced for every 5 moles of O2 used. Therefore, the number of moles of O2 needed would be (5/2) x (6/2) = 7.5 moles.

e) If you get 6 moles of N2O5 during your reaction, according to the equation, 2 moles of N2O5 are produced for every 2 moles of N2 used. Therefore, the number of moles of N2 needed would be (2/2) x (6/2) = 3 moles.

Names: The chemical names for the compounds involved in the equation are:

O2: Oxygen gas

N2: Nitrogen gas

N2O5: Dinitrogen pentoxide gas

A chemical reaction between nitrogen and oxygen is represented by the balanced chemical equation 2N2(g) + 5O2(g) 2N2O5(g). The quantities of the reactants and products used in this reaction were questioned.

We may use stoichiometry to determine the mole ratio of O2 to N2O5, which will allow us to calculate how many moles of N2O5 is generated when 2 moles of O2 are consumed.

The equation shows that in order to produce 2 moles of N2O5, 5 moles of O2 must react with 2 moles of N2. The result is the production of (2/5) x 2 = 0.8 moles of N2O5.

Similar calculations can be used to determine how many moles of N2O5 are created when 1 mole of O2 or 1 mole of N2 is used.

learn more about moles here

https://brainly.com/question/28330489

#SPJ1

[tex]Fe +2 HCl[/tex] yields [tex]FeCl_2[/tex] and [tex]H_2[/tex]. One atom of [tex]Fe[/tex] combines with two compounds of [tex]HCl[/tex] to create 1 molecule of [tex]FeCl_2[/tex]  or one molecule of [tex]H_2[/tex], as shown by the equation's balanced form.    [tex]2Fe + 2HCl = 2FeCl_2 + H_2[/tex]

A mathematical statement known as an equation is created when two expressions are joined by the equal sign. An example is [tex]3x - 5[/tex] 16 in mathematics. By resolving this equation, we may find that the variable x has a value of 7.

[tex]Fe^ +2[/tex]  [tex]HCl[/tex] produces [tex]H_2[/tex] and  [tex]FeCl2.[/tex] According to the equation's balanced version, one atom of Fe reacts with two [tex]HCl[/tex] molecules to make one molecule of [tex]FeCl_2[/tex] or one molecule of  [tex]H_2[/tex].

Therefore, [tex]2Fe + 2HCl = 2FeCl_2 + H_2[/tex] one atom of Fe reacts with two [tex]HCl[/tex] molecules to make one molecule of [tex]FeCl_2[/tex] or one molecule of  [tex]H_2[/tex].

Learn more about equation here:

https://brainly.com/question/30087623

#SPJ9

Answer: The answer for this question is 45.9.

Explanation: Since there are numbers with different significant figures, the number or numbers that have less significant figures will be the one you round to. In this case, the numbers in the problem are 32.6,735, and 1035. Since we need to find the numbers that have the least significant figures, the numbers 32.6 and 735 have three significant figures while 1035 has 4 significant figures. Since we need to choose the numbers that have the least significant figures, these numbers are 32.6 and 735 since they have three significant figures. Round your answer to three significant figures and you get 45.9 as your answer.

The mass of carbon dioxide produced from the complete combustion of 8.40x10^-3 g of methane is 0.023 g.

Mass can be defined as the measure of the amount of matter in a body.

The balanced chemical equation for the complete combustion of methane (CH4) is:

CH4 + 2O2 → CO2 + 2H2O

This equation tells us that one mole of methane reacts with two moles of oxygen gas (O2) to produce one mole of carbon dioxide (CO2) and two moles of water (H2O).

We can use the molar mass of methane and the balanced equation to determine the amount of carbon dioxide produced from the given mass of methane.

First, we need to convert the mass of methane to moles:

moles of CH4 = mass / molar mass = 8.40x10^-3 g / 16.04 g/mol = 5.239x10^-4 moles

Next, we can use the balanced equation to find the number of moles of CO2 produced:

1 mole of CH4 produces 1 mole of CO2

So, 5.239x10^-4 moles of CH4 will produce 5.239x10^-4 moles of CO2.

Finally, we can use the molar mass of carbon dioxide to convert moles to grams:

mass of CO2 = moles of CO2 × molar mass of CO2

mass of CO2 = 5.239x10^-4 moles × 44.01 g/mol = 0.023 g

Therefore, the mass of carbon dioxide produced from the complete combustion of 8.40x10^-3 g of methane is 0.023 g.

Learn more about molar mass here : brainly.com/question/24236159

#SPJ1

Answer: 2.78

Explanation:

 To calculate the pH of 0.16M CH3COOH, we need to use the dissociation constant (Ka) of the acid, which is given as 1.74 × 10^-5 mol dm^-3.

The dissociation of CH3COOH is as follows:

CH3COOH + H2O ↔ CH3COO- + H3O+

The equilibrium constant expression for the dissociation of CH3COOH is:

Ka = [CH3COO-][H3O+] / [CH3COOH]

We can assume that [H3O+] is equal to [CH3COO-] since the acid is weak and will not dissociate completely. Therefore, the equilibrium constant expression can be simplified as:

Ka = [H3O+]^2 / [CH3COOH]

[H3O+]^2 = Ka x [CH3COOH]

[H3O+]^2 = 1.74 × 10^-5 x 0.16

[H3O+]^2 = 2.784 × 10^-6

[H3O+] = √2.784 × 10^-6

[H3O+] = 0.00167 M

Therefore, the pH of the solution can be calculated as:

pH = -log[H3O+]

pH = -log(0.00167)

pH = 2.78

Therefore, the pH of the 0.16M CH3COOH solution is 2.78.

Whereas freezing, condensation, or deposition are exothermic processes, fusion, vaporisation, and  were endothermic processes. Changes in a system's energy occur together every phase transition.

Potential energy is the type of energy that is transforming during a phase change. Either elevated body temperature (PE increases) and released (PE drops) throughout a phase change will permit the molecules either move apart or join together.

Melting is the process of changing from of the solid to liquid state. freezing: the transformation of a liquid into a solid. The process of evaporation is the change from a liquid to a gas. Condensing: The change from a gaseous to a liquid state.

To know more about exothermic visit:

https://brainly.com/question/4345448

#SPJ1

The total enzyme concentration [Et] is 6 nM.

Enzyme concentration is the amount of an enzyme present in a given solution. The concentration of enzymes can have an effect on the rate of reaction. If the concentration of enzymes is higher, the rate of reaction will be faster, and if the concentration of enzymes is lower, the rate of reaction will be slower.Enzyme concentration is important because it can affect the outcome of a reaction, and therefore, it must be carefully monitored.

The total enzyme concentration [Et] can be calculated using the Michaelis-Menten equation, which states that[tex]Vo= [Et] * kcat * (\frac{[S]}{Km} + [S])[/tex]

Plugging in the given values, we get:

[tex]480 nM/min = [Et] * 20 min^{-1}* (\frac{6mM}{4uM} + 6mM)[/tex]

Solving for [Et], we get:

[Et] = 6 nM

learn more about concentration Refer:brainly.com/question/29276511

#SPJ1

The degree of association of AlCl3 into Al2Cl6 is 0.663. The degree of association of AlCl3 into Al2Cl6 can be determined using the ideal gas law and the van't Hoff factor.

Firstly, we need to calculate the number of moles of AlCl3 present in the vessel using the formula n = m/M, where m is the mass of AlCl3 and M is the molar mass of AlCl3.

n = 10.32g / 133.34 g/mol = 0.0774 mol

Next, we can use the ideal gas law equation PV = nRT to calculate the number of moles of particles in the gas phase. Rearranging this equation, we get:

n = PV/RT

where P is the pressure, V is the volume, R is the gas constant and T is the temperature in Kelvin.

n = (1.7 x 10 N/m²) x 1 dm³ / (8.31 J/mol/K x 353 K) = 7.55 x 10⁻⁴ mol

The van't Hoff factor (i) is the ratio of the actual number of particles in solution to the number of formula units dissolved. For a completely dissociated compound, the van't Hoff factor is equal to the number of ions produced. In the case of AlCl3, it undergoes a degree of association to form Al2Cl6, so the van't Hoff factor is less than 1.

We can now use the formula i = 1 + (α - 1)β, where α is the degree of association and β is the number of particles in solution per formula unit. For AlCl3, β = 4 (AlCl3 contains one Al and three Cl atoms), and assuming a degree of association of x, we get:

i = 1 + (x - 1) x 4 = 4x - 3

Substituting the values for n and i into the equation n = iC, where C is the concentration in mol/dm³, we get:

7.55 x 10^-4 mol = (4x - 3) C

Solving for x, we get:

x = 0.663

Therefore, the degree of association of AlCl3 into Al2Cl6 is 0.663.

To know more about van't Hoff factor, visit:

https://brainly.com/question/30905748

#SPJ1

The flammability of natural gas ranges from 5 to 15 percent. This indicates that no combustion would take place in any mixture with a natural gas to air ratio of less than 5% or greater than 15%.

The lowest concentration of a gas at which combustion can occur is known as the LEL. A reading in%LEL measures the percentage of that LEL value. The LEL, for instance, is 5% by volume for methane. Half of that amount, or 2.5% by volume, is 50% LEL.

Divide the unknown concentration by the LEL specified in the NFPA Handbook to determine the LEL of any gas in air.

To know more about flammability visit:-

brainly.com/question/13323225

#SPJ1

Answer:

where is the other temperature? so i can help you

The pOH of the solution is 10.92.

Equation: The relationship between a solution's pH and pOH is:

pH + pOH = 14

where pH is equal to the negative logarithm of the concentration of hydrogen ions (H+), and pOH is equal to the negative logarithm of the concentration of hydroxide ions (OH-).

We must first determine the [OH-] concentration to determine the solution's pOH. We can apply the following:

Kw = [H+][OH-] = 1.0 x 10^-14 at 25°C

where Kw is the water-specific ion product constant.

If we rewrite this equation, we obtain:

[OH-] = Kw/[H+] = 1.0 x 10^-14 / 8.4 x 10^-3 = 1.19 x 10^-11 mol/L

We can now calculate pOH's value using the definition of the term:

pOH = -log[OH-] = -log(1.19 x 10^-11) = 10.92

to know more about the solution here:

brainly.com/question/30665317

#SPJ1

Answer: 0.0499 moles of sodium hydroxide

Explanation:

We can determine the number of moles by using the Molarity equation:

Molarity = Moles / Volume (volume is always in Liters)

We have 2 out of 3 components of this equation

Molarity = 1.000 M

Volume = 49.93 mL / 1000 = 0.0499 L

So we rearrange the equation like the following:

Moles = Molarity x volume

          = 1.000 Mx 0.0499 L

          = 0.0499 moles of sodium hydroxide

To solve both problems, we need to use the equations for calculating boiling point elevation and freezing point depression:

Boiling point elevation: ΔTb = Kb x molality

Freezing point depression: ΔTf = Kf x molality

where:

For both problems, we assume that the solute is completely dissolved in the solvent and that the resulting solution is ideal.

First, we need to calculate the molality of the ethanol solution:

molality = moles of solute / mass of solvent in kg

Next, we need to find the boiling point elevation and freezing point depression:

ΔTb = Kb x molality

ΔTf = Kf x molality

For water, Kb = 0.512 °C/m and Kf = 1.86 °C/m.

ΔTb = 0.512 °C/m x 1.09 mol/kg = 0.558 °C

ΔTf = 1.86 °C/m x 1.09 mol/kg = 2.03 °C

Therefore, the boiling point of the solution is 100 + 0.558 = 100.558 °C, and the freezing point is 0 - 2.03 = -2.03 °C.

2. First, we need to calculate the molality of the benzoic acid solution:

molality = moles of solute / mass of solvent in kg

Next, we need to find the boiling point elevation and freezing point depression:

ΔTb = Kb x molality

ΔTf = Kf x molality

For water, Kb = 0.512 °C/m and Kf = 1.86 °C/m.

ΔTb = 0.512 °C/m x 0.819 mol/kg = 0.419 °C

ΔTf = 1.86 °C/m x 0.819 mol/kg = 1.52 °C

Therefore, the boiling point of the solution is 100 + 0.419 = 100.419 °C, and the freezing point is 0 - 1.52 = -1.52 °C.

More on boiling and freezing points can be found here: https://brainly.com/question/13380426

#SPJ1

The number of particles in the gas is [tex]4.72 * 10^{24}[/tex], the volume of the gas at 4 atm is 40 L, and the volume of the gas at 300 K is 30 L.

Avogadro's Law: Equal volumes of gases at the same temperature and pressure contain equal numbers of particles (molecules or atoms).

Boyle's Law: For a fixed amount of gas at a constant temperature, the pressure and volume are inversely proportional to each other.

Charles's Law: For a fixed amount of gas at a constant pressure, the volume and temperature are directly proportional to each other.

PV = nRT is the formula for the ideal gas law,

where P is pressure, V is volume, n is the number of molecules of gas, R is gas constant, and T is temperature in Kelvin.

Mass of gas (m) = 4 g

Temperature (T) = 200 K

Pressure (P) = 8 atm

Volume (V) = 20 L

First, we can use the ideal gas law to calculate the number of moles of gas:

n = PV/RT

n = (8 atm * 20 L) / (0.0821 L.atm/mol.K * 200 K)

n = 7.85 moles

Next, we can use Avogadro's Law to find the number of particles (molecules or atoms):

1 mole of gas = [tex]6.02 * 10^23[/tex] particles

7.85 moles of gas =[tex]7.85 * 6.02 * 10^23[/tex]particles

= [tex]4.72 * 10^24[/tex] particles

We can also use Boyle's Law and Charles's Law to find the volume of the gas at different conditions:

Boyle's Law:

[tex]P_1V_1 = P_2V_2[/tex]

If we keep the temperature constant at 200 K, we can use this relationship to find the volume of the gas at a different pressure. Let's say we want to know the volume of the gas at 4 atm:

[tex]P_1[/tex] = 8 atm

[tex]V_1[/tex] = 20 L

[tex]P_2[/tex] = 4 atm

[tex]V_2[/tex]= ?

[tex]P_1V_1 = P_2V_2[/tex]

8 atm x 20 L = 4 atm x [tex]V_2[/tex]

[tex]V_2[/tex] = (8 atm x 20 L) / 4 atm

[tex]V_2[/tex] = 40 L

Charles's Law:

[tex]V1/T1 = V2/T2[/tex]

If we keep the pressure constant at 8 atm, we can use this relationship to find the volume of the gas at a different temperature.

Let's say we want to know the volume of the gas at 300 K:

[tex]V_1[/tex] = 20 L

[tex]T_1[/tex]= 200 K

[tex]V_2[/tex] = ?

[tex]T_2[/tex] = 300 K

[tex]V_1/T_1 = V_2/T_2[/tex]

20 L / 200 K = [tex]V_2[/tex] / 300 K

[tex]V_2[/tex] = (20 L / 200 K) x 300 K

[tex]V_2[/tex] = 30 L

Therefore, the number of particles in the gas is [tex]4.72 * 10^{24}[/tex], the volume of the gas at 4 atm is 40 L, and the volume of the gas at 300 K is 30 L.

For more such questions on Avogadro's Law , Visit:

https://brainly.com/question/26931664

#SPJ11

Answer: The solubility of NaNO3 (sodium nitrate) in water increases as temperature increases. Therefore, we need to know the solubility of NaNO3 at different temperatures to determine the temperature at which 140 g of NaNO3 can be fully dissolved in water.

According to the solubility curve for NaNO3, the maximum solubility of NaNO3 in water is approximately 88 g per 100 g of water at 80°C. This means that at 80°C, we can dissolve 88 g of NaNO3 in 100 g of water to make a saturated solution.

To fully dissolve 140 g of NaNO3, we need to dissolve it in a sufficient amount of water that can dissolve at least 140 g of NaNO3. Using a proportion, we can calculate the amount of water required to dissolve 140 g of NaNO3 at 80°C:

88 g NaNO3 / 100 g water = 140 g NaNO3 / x g water

Solving for x, we get:

x = 159.1 g water

This means that at 80°C, we need to dissolve 140 g of NaNO3 in at least 159.1 g of water to make a saturated solution, in which all of the NaNO3 will be dissolved.

Therefore, the temperature at which 140 g of NaNO3 can be fully dissolved in water is approximately 80°C.

Explanation:

a. The rate law rate=k[NO2]^2 indicates that the reaction is second order with respect to NO2.

b. The rate law rate=k indicates that the reaction is zero order with respect to the reactant(s).

c. The rate law rate=k[H2][Br2]^1/2 indicates that the reaction is first order with respect to H2 and half-order with respect to Br2. Therefore, the overall order of the reaction is 1 + 1/2 = 3/2 order.

d. The rate law rate=k[NO]^2[O2] indicates that the reaction is third order overall. The reaction is second order with respect to NO and first order with respect to O2.

The term "rate law" is commonly used to refer to the integrated rate law. K in a rate law is the rate constant, a value specific to each reaction that determines the rate of reaction. Orders in a rate law describe the dependency of the reaction rate on the concentration of each reactant, with each reactant having its own order. The overall reaction order is the sum of the individual orders, which can be determined through experiments.

To know more about rate law, visit: brainly.com/question/30379408

#SPJ4

A double replacement is Na2SO4 (aq) + BaCl2 BaSO4 (s) + 2 NaCl (aq) + 2 NaCl (aq). The reaction Na2SO4 + BaCl2 is endothermic. When barium chloride (BaCl2) and sodium sulphate (Na2SO4) combine, sodium chloride and barium sulphate are formed.

When Sodium sulphate(Na 2 SO 4) interacts with Barium chloride solution (), a white precipitate of Barium sulphate() and Sodium chloride is generated.

When barium chloride is introduced to dilute sulphuric acid, a white precipitate of barium sulphate forms as a result of barium displacement from its chloride, as seen below: BaCl2 + H2SO4 BaSO4 + 2HCl.

learn more about double replacement

https://brainly.com/question/23918356

#SPJ1

Hypothesis: Increasing the cooling rate during the solidification of aluminum will result in a finer grain structure in the final solid.

When a liquid metal such as aluminum is cooled and solidified, the atoms in the liquid begin to arrange themselves into a crystalline structure. The rate at which this happens can have a significant effect on the final microstructure of the solid. If the cooling rate is slow, larger grains will form as the atoms have more time to move and arrange themselves into larger clusters. If the cooling rate is faster, there is less time for the atoms to move and larger clusters cannot form, resulting in a finer grain structure. Therefore, the hypothesis proposes that increasing the cooling rate during the solidification of aluminum will lead to a finer grain structure in the final solid. This hypothesis could be tested by varying the cooling rate during the solidification process and then examining the microstructure of the resulting solid.

Learn more about Hypothesis,

https://brainly.com/question/29519577

#SPJ1

Hypothesis: Increasing the cooling rate during the solidification of aluminium will result in a finer grain structure in the final solid.

The following methods can be used to demonstrate whether a solid is:

Ionic (NaCl):

Solubility test: Since NaCl is extremely soluble in water, its ionic nature can be verified by this fact.

Conductivity test: NaCl transmits electricity when it is molten or dissolved because it contains charged ions.

Metallic (Ca):

Conductivity test: Due to the existence of free electrons within their crystal structure, metals like calcium carry electricity.

Ductility and malleability test: Due to their malleability and ductility, metals are readily deformed when under pressure.

Covalent Network (Quartz, SiO2):

Hardness test: Because of the intense covalent bonds between atoms, covalent network solids like quartz are exceedingly hard.

Melting point test: Due to the powerful intermolecular forces between atoms, covalent network solids frequently have high melting and boiling points.

Polar Molecular (sugar, C6H12O6):

Solubility test: Sugar and other polar compounds can dissolve in polar solvents like water but cannot dissolve in nonpolar solvents.

Melting and boiling point test: Due to weaker intermolecular interactions, polar molecular solids have lower melting and boiling points than ionic or covalent network solids.

To know more about ionic, visit:

brainly.com/question/15241125

#SPJ1

Answer:

To make an 800 mL solution of 3.0 M glucose (C6H12O6), you would need 2.4 moles of glucose.

Here’s the work: Molarity (M) = moles of solute / liters of solution Rearranging the equation to solve for moles of solute: moles of solute = Molarity (M) * liters of solution Since you have 800 mL or 0.8 L of a 3.0 M glucose solution: moles of glucose = 3.0 M * 0.8 L = 2.4 moles.

The answer is [tex]4.94 x 10^23[/tex]  atoms.

To determine the total number of atoms in 62.5 g of carbon disulfide (CS2), we need to use Avogadro's number and the molecular weight of CS2.

The molecular weight of CS2 is:

Carbon atomic weight = 12.01 g/mol

Sulfur atomic weight = 32.06 g/mol

2 sulfur atoms x 32.06 g/mol + 1 carbon atom x 12.01 g/mol = 76.13 g/mol

Now, we can use the formula:

Number of moles = mass ÷ molecular weight

Number of moles of CS2 = 62.5 g ÷ 76.13 g/mol = 0.821 mol

Finally, we can use Avogadro's number, which is[tex]6.022 x 10^23[/tex] atoms per mole, to calculate the total number of atoms in 62.5 g of CS2:

Total atoms = Number of moles × Avogadro's number

Total atoms = 0.821 mol ×[tex]6.022 x 10^23[/tex] atoms/mol

Total atoms =[tex]4.94 x 10^23[/tex] atoms

Therefore, there are approximately[tex]4.94 x 10^23[/tex]atoms in 62.5 g of carbon disulfide (CS2).

To know more about total atoms:

https://brainly.com/question/21710360

Answer:

Nucular

Explanation:

When one atom splits into 2, it's nucular

molar mass of empirical formula = (20 x 12.01 g/mol) + (24 x 1.01 g/mol) + (1 x 14.01 g/mol) = 324.44 g/mol ratio = 324.44 g/mol / 324 g/mol = 1.001. The molecular formula of quinine is C20H24N.

The active component of cinchona extracts, which have been used for this purpose since before 1633, is utilized as an antimalarial medication. Quinine has been utilized in conventional cold remedies for its use as a mild antipyretic and analgesic.

Plasmodium falciparum malaria is treated with quinine. Malaria is brought on by the parasite Plasmodium falciparum, which enters the body through the red blood cells. Quinine functions by either eliminating the parasite or halting its growth.

to know more about quinine here;

brainly.com/question/17275075

#SPJ1