Puck A and puck B are free to slide without friction on a horizontal air table; the mass of puck A has been measured to be 165. 0 grams , but the mass of puck B is unknown. The pucks are made of super-ball like material, so any collision between them should be elastic. An experiment is done with puck B at rest at the center of the air table, and with puck A sent at 55. 0 cm/s to make a glancing collision with puck B. After the collision, puck A is measured to have a speed of 29. 0 cm/s , and is observed to have been deflected by 27. 0 degrees from its original direction. What was the y component of puck B's momentum after the collision?

In a given stationary wave, the distance between two successive nodes or antinodes is half of the wavelength.

The distance between identical points (adjacent crests) in adjacent cycles of a waveform signal carried in space or along a wire is defined as the wavelength.

The SI unit of wavelength is the meter, abbreviated as m. Multiples or fractions of a meter are also employed when measuring wavelength.

Learn more about wavelength here:

https://brainly.com/question/10728818

#SPJ1

The kinetic energy of the spinning disk is 108 Joules.

To calculate the kinetic energy of the spinning disk, we'll use these terms: mass (m), radius (r), angular velocity (ω), and moment of inertia (I). Here's a step-by-step explanation:

1. First, find the moment of inertia (I) for the disk using the formula for a solid disk: I = (1/2) * m * r^2
  I = (1/2) * 12 kg * (2 m)^2
  I = 0.5 * 12 kg * 4 m^2
  I = 24 kg m^2

2. Next, calculate the kinetic energy (KE) using the formula: KE = (1/2) * I * ω^2
  KE = (1/2) * 24 kg m^2 * (3 rad/s)^2
  KE = 0.5 * 24 kg m^2 * 9 (rad^2/s^2)
  KE = 108 Joules

For more about kinetic energy:

https://brainly.com/question/26472013

#SPJ11

(1) The rock came to be in a various position than you thought it was by way of the wonder of refraction. The rock's position seemed different due to light refraction as it travels at varying speeds through different mediums.

2. Rock looks red as it absorbs all colors of sunlight except red.

2b.  When white light enters water, it refracts and splits into various colors.

This causes the object to perform at a different position than it literally is. In this case, the light indications coming from the rock were bent when they entered the water, making the rock to appear at a more ignorant wisdom than it actually was.

Therefore, in response to question 2, rock appears red by way of the selective assimilation and reflection of light. The rock absorbs all of the banner of silvery light except for flaming, which is mirrored back to our eyes. This is because the microscopic structure of the rock absorbs all the banner except that red, that is reflected back.

Learn more about Rock from

https://brainly.com/question/398139

#SPJ1

The two errors in the passage are:

pH is a measure of the concentration of OH− ions in a solution of an acid or base. The pH scale plots the concentration of solutions in a range from 0–16.

The answer that correct both errors is:

pH is a measure of the concentration of H+ ions in a solution of an acid or base. The pH plots the concentration of solutions in a range from 0–14.

A solution's acidity or basicity is determined using the pH scale. A pH of 0-6.9 is considered acidic, a pH of 7 is neutral, and a pH of 7.1-14 is considered basic. The pH scale is logarithmic, which means that each change in pH reflects a tenfold difference in acidity or basicity.

The concentration of hydrogen ions (H+) in a solution determines the pH of the solution. A base is a chemical that reduces the concentration of H+ ions in a solution, whereas an acid raises the concentration of H+ ions in a solution.

Therefore, The  correct answer choice is:

" pH is a measure of the concentration of H+ ions in a solution of an acid or base. The pH plots the concentration of solutions in a range from 0–14."

For more such questions on pH scale, click on:

https://brainly.com/question/14965267

#SPJ11

The correct answer is: The mass of A is less than C, which is less than B, where all have the same distance from each other. The gravitational attraction between objects A and B is less than the attraction between objects B and C. The attraction between objects A and C is less than the attraction between the other two sets of objects.

To understand the relationship between the masses of objects A, B, and C, we need to consider the gravitational attraction between them. According to the given information:

1. Gravitational attraction between A and B is less than the attraction between B and C.
2. Gravitational attraction between A and C is less than the attraction between the other two sets of objects (A&B, B&C).

Based on these facts, we can deduce the relationship between the masses of objects A, B, and C. The gravitational force between two objects is determined by their masses and the distance between them, as given by Newton's law of universal gravitation:

F = G * (m1 * m2) / r²

Since the distance between all objects is the same, the gravitational force is directly proportional to the product of their masses. From the given information, we can determine the following:

- The product of masses A and B is less than the product of masses B and C.
- The product of masses A and C is less than the product of masses A and B, and the product of masses B and C.

Considering these relationships, we can conclude that the mass of A is less than C, which is less than B. Therefore, the correct answer is: The mass of A is less than C, which is less than B.

Learn more about gravitational attraction at: https://brainly.com/question/15090289

#SPJ11

The wavelengths of the components of the first line of the Lyman series, taking the fine structure of the 2p level into account, are 121.4 nm and 121.2 nm for j = 1/2 and j = 3/2, respectively.

The Lyman series is a series of spectral lines in the hydrogen atom's emission spectrum that corresponds to transitions from higher energy levels to the ground state. The first line of the Lyman series corresponds to a transition from the 2p energy level to the 1s energy level.

To take the fine structure of the 2p level into account, we need to use the formula for the energy of a hydrogen atom with fine structure:

[tex]E= -13.6 eV*\frac{1}{n^{2} } *[1+a^{2} * \frac{(\frac{Z}{n}) ^{4}}{(n-j-\frac{1}{2})^{2} } ][/tex]

where n is the principal quantum number, Z is the atomic number (1 for hydrogen), j is the total angular momentum quantum number of the electron, and α is the fine structure constant.

For the 2p energy level, j can be either 1/2 or 3/2, so we need to calculate the wavelengths for both possibilities. Using the formula for the energy of the 2p level and the energy of the 1s level (-13.6 eV), we can calculate the wavelengths of the first line of the Lyman series with fine structure for each case:

For j = 1/2: λ = 121.6 nm * [1 - (1/9) * α²] = 121.6 nm * 0.9988 = 121.4 nm

For j = 3/2: λ = 121.6 nm * [1 - (4/9) * α²] = 121.6 nm * 0.9972 = 121.2 nm

Taking the fine structure of the 2p level into consideration, the wavelengths of the components of the first line of the Lyman series are 121.4 nm and 121.2 nm for j = 1/2 and j = 3/2, respectively.

To know more about the Lyman series, here

https://brainly.com/question/29597178

#SPJ4

Yes, the cars will have a time when the two cars are traveling at the same speed if they leave at the same time and arrive at the same time.

Let's assume that the two cars have different velocities and their positions at any given time can be represented as x₁(t) and x₂(t), where t is the time in seconds. We know that the two cars leave at the same time and arrive at the same time, so the time taken for both cars to travel from the starting point to the end point is the same. Let's call this common time "t".

So, x₁(t) = x₂(t) (both cars arrive at the same point)

Differentiating both sides with respect to time, we get:

v₁ = v₂

where v₁ and v₂ are the velocities of the two cars.

Therefore, if the two cars leave at the same time and arrive at the same time, then there must be a time when they are traveling at the same velocity.

This can be proven using calculus by showing that if the two cars have different velocities at any given time, then there must be a point in time when their velocities are equal. This is because the derivative of the difference in their positions with respect to time (x₁(t) - x₂(t)) is the difference in their velocities (v₁ - v₂), which must be non-zero for any non-zero difference in their positions. Since the derivative of a continuous function can only change sign at a point where it is zero, there must be a time when v₁ = v₂.

Therefore, we have proved that there must be a time when the two cars are traveling at the same speed if they leave at the same time and arrive at the same time.

To know more about time, here

brainly.com/question/28187872

#SPJ4

--The complete question is, Two cars drive from one spotlight to the next, leaving at the same time and arriving at the same time. Is there ever a time when they are going the same speed? Prove or disprove.--

The magnitude of the angular velocity of the wheel after the block has descended 3.80 m is 5.23 rad/s.

Explanation :

We can use conservation of energy to solve this problem. Initially, the system is at rest and has a total energy of zero. As the block descends, its potential energy is converted into kinetic energy and work done by friction. We can express this as:

[tex]mgh = (1/2)mv^2 + W_{friction} + (1/2)Iw^2[/tex]

where m is the mass of the block, g is the acceleration due to gravity, h is the height the block descends (3.80 m), v is the velocity of the block at the bottom, W_friction is the work done by friction (−8.50 J), I is the moment of inertia of the wheel, and ω is the angular velocity of the wheel.

Since the wire is wrapped around the rim of the wheel, the distance the block descends (3.80 m) is also the distance the rim of the wheel moves. Therefore, the work done by friction can be expressed as:

[tex]W_{friction} = -F_{friction} * d = -[/tex]τΘ

where F_friction is the force of friction at the axle, τ is the torque exerted by friction, d is the distance the rim moves, and θ is the angle through which the wheel rotates. Since the wheel rotates through an angle of θ = h/r = 3.80 m/0.190 m = 20.0 rad, we have:

τ = W_friction / θ = -8.50 J / 20.0 rad = -0.425 N*m

Substituting the given values into the energy conservation equation and solving for ω, we get:

[tex](0.350 kg)(9.81 m/s^2)(3.80 m) = (1/2)(0.350 kg)v^2 - 0.425 N*m + (1/2)(0.470 kgm^2)w^2[/tex]

Simplifying and solving for ω, we get:

ω = √[(2mgh + 2τ)/I]

[tex]w =\sqrt{[(2)(0.350 kg)(9.81 m/s^2)(3.80 m) + 2(-0.425 Nm)] / 0.470 kgm^2}[/tex]

ω = 5.23 rad/s

To know more about angular velocity refer here

https://brainly.com/question/29557272#

#SPJ11

Mike does approximately 303.2175 joules of work on the mower each time he pushes it 9.1 meters across the yard.

To calculate the work done by Mike on the mower, we can use the formula:

Work = Force * Distance * cos(theta)

where:

Given:

Force = 45 N

Distance = 9.1 m

theta = 41°

Converting the angle to radians:

theta_rad = 41° * (π/180) ≈ 0.7156 radians

Calculating the work:

Work = 45 N * 9.1 m * cos(0.7156)

Work ≈ 45 N * 9.1 m * 0.7483

Work ≈ 303.2175 J

Therefore, Mike does approximately 303.2175 joules of work on the mower each time he pushes it 9.1 meters across the yard.

To know more about work done refer here

https://brainly.com/question/3902440#

#SPJ11

To use Ohm's Law in the form of y=mx+c to calculate the average resistance of an ohmic conductor, you need to understand that Ohm's Law is V=IR, where V is voltage, I is current, and R is resistance.

In this case, y represents voltage (V), m represents resistance (R), x represents current (I), and c is the constant (0 for an ohmic conductor).

Now, you can rewrite Ohm's Law as y=mx+c or V=IR+0. To find the average resistance, you'll need to collect data on voltage (V) and current (I) at various points.

Then, plot these points on a graph with voltage (y-axis) against current (x-axis). The slope (m) of the best-fit line through these points will give you the average resistance (R) of the ohmic conductor.

To learn more about current, refer below:

https://brainly.com/question/13076734

#SPJ11

Genes are the basic units of heredity. (Los genes son las unidades básicas de la herencia.)

A short stretch of ADN called a gene. The body's genes instruct it on how to produce particular proteins. About 20,000 genes are found in each human body cell. Together, they make up the genetic makeup of the human body and determine how it functions.

Fundamental unit of the inheritance from parents to children. The genes are constructed from ADN sequences and are arranged one after the other in certain locations within the chromosomal nuclei of cells.

To know more about ADN visit:-

https://brainly.com/question/30297148

#SPJ1

A simple circuit has a 20 Ω resistor and carries 0. 3 A. The voltage of the power source is 6 V.  In a simple circuit with only one resistor, the voltage across the resistor is equal to the voltage of the power source.

Using Ohm's law, we can determine the voltage of the power source by multiplying the resistance (R) of the circuit by the current (I) flowing through it. Thus, we have:

V = IR

Substituting the given values, we get:

[tex]V = (0.3 A)(20\; \Omega) = 6 V[/tex]

Therefore, the voltage of the power source in the circuit is 6 volts. In a simple circuit with only one resistor, the voltage across the resistor is equal to the voltage of the power source.

This is because the sum of the voltages across all the components in the circuit must equal the total voltage of the power source, due to the conservation of energy.

It's important to note that in real-world circuits, the voltage of the power source can fluctuate due to various factors such as fluctuations in the electrical grid or changes in the internal resistance of the power source itself.

To know more about resistors refer here:

https://brainly.com/question/31258648#

#SPJ11

If lamp A1 turns off, the brightness of A2 will not be affected, as it is still connected in parallel to the power source.

The brightness of A3 will decrease, since it is connected in series to the parallel combination of A1 and A2. In a series circuit, the current flowing through each element is the same, so if one element fails, the current through the remaining elements will decrease, causing a decrease in brightness.

Consider the analogy of a water pipe. The parallel connection of A1 and A2 is like two pipes connected to the same source, allowing the water (or current) to flow equally through both. The series connection of A3 to A1 and A2 is like a pipe connected in series to two others. If one of the pipes fails, the water flow through the other two will decrease, resulting in less water coming out of the end of the series pipe. Similarly, the brightness of A3 will decrease if A1 turns off, as the current flowing through it will decrease.

To know more about the Identical lamps, here

https://brainly.com/question/29018302

#SPJ4

The time it will take the radio signal to travel from Earth to the spaceship is 36,500 seconds.

The time it will take the radio signal to travel from Earth to the spaceship is calculated as follows;

t = d/v

where;

The time taken for the signal to travel is calculated as follows;

t = (7.3 x 10¹⁰ m ) / (2 x 10⁶ m/s )

t = 36,500 seconds

Learn more about time of motion of signals here: https://brainly.com/question/21235005

#SPJ1

The current in the coil is approximately 0.1419 A (amps).

To find the current in a coil, we need to use the formula for magnetic field strength (B) in a solenoid:
B = μ₀ × n × I
Where:
- B is the magnetic field strength (given as 388 x 10⁻³ T)
- μ₀ is the permeability of free space (approximately 4π x 10⁻⁷ T m/A)
- n is the number of turns per meter (density of turns, given as 861658 turns/m)
- I is the current in the coil (the value we want to find)
First, let's plug in the given values:
388 x 10⁻³ T = (4π x 10⁻⁷ T m/A) × 861658 turns/m × I
Now, we need to isolate I by dividing both sides of the equation by (4π x 10⁻⁷ T m/A × 861658 turns/m):
I = (388 x 10⁻³ T) / (4π x 10⁻⁷ T m/A × 861658 turns/m)
Next, we can calculate the current:
I ≈ 0.1419 A

Learn more about current here:-

https://brainly.com/question/13076734

#SPJ11

If you consistently consume four cookies (140 Calories) every day for a year, you will end up consuming an extra 51,100 calories (140 x 365).

This excess of calories can lead to weight gain as your body stores the excess energy as fat.

In general, one pound of body weight is equal to approximately 3,500 calories. So, if you consume 51,100 extra calories in a year, you may gain approximately 14.6 pounds (51,100 / 3,500). This weight gain can contribute to various health problems such as increased risk of heart disease, diabetes, and joint problems.

It is important to maintain a balanced and healthy diet by consuming the appropriate amount of calories needed to sustain your body's energy needs. Consuming too many extra calories can lead to unintended weight gain and negative health outcomes.

It is recommended to consult with a healthcare professional to determine the appropriate amount of calories needed to maintain a healthy weight and lifestyle.

To Learn More About Calories

https://brainly.com/question/11844409

SPJ11

The electromagnetic waves that travel at the same speed as light are x-rays, gamma rays, infrared radiation, radio waves, and microwaves.

The speed of light in a vacuum is a constant value, known as the speed of light, which is approximately 299,792,458 meters per second. All electromagnetic waves, including x-rays, gamma rays, infrared radiation, radio waves, and microwaves, travel at this speed in a vacuum.

Radar is an electromagnetic wave that is used for detecting and locating objects. It travels at a speed close to the speed of light but is not exactly the same. Ultrasonic waves, on the other hand, are sound waves that travel through a medium, such as air or water, and have a much lower speed than light.

Cell phone signals are a form of electromagnetic waves, but they do not travel at the same speed as light. Their speed is significantly lower and depends on various factors such as the distance from the transmitter, interference, and the type of carrier signal used.

In summary, only x-rays, gamma rays, infrared radiation, radio waves, and microwaves travel at the same speed as light, while radar, cell phone signals, and ultrasonic waves do not.

To learn more about speed click on,

https://brainly.com/question/31165460

#SPJ4

The minimum height the mirror must have for you to be able to see the top of the table in the mirror is 4.5 meters.

To see the top of the table in the mirror, the line of sight from your eyes to the top of the table must reflect off the mirror and enter your eyes. This means that the angle of incidence (the angle between the incident light and the normal to the mirror) must equal the angle of reflection (the angle between the reflected light and the normal to the mirror).

Let h be the height of the mirror. The distance from your eyes to the top of the table is:

d = 1.9 m + 0.8 m = 2.7 m

The distance from the mirror to the top of the table (along the reflected path) is:

2 × 3.2 m = 6.4 m

The angle of incidence is the angle between the line of sight from your eyes to the top of the table and the normal to the mirror. This angle can be calculated using trigonometry. The opposite side of the angle is the height of your eyes above the floor (1.9 m), and the adjacent side is the distance from your eyes to the mirror (3.2 m). Thus:

sin θ = opposite/hypotenuse = 1.9/3.2 = 0.59375

θ = sin^-1(0.59375) = 36.87°

Since the angle of incidence equals the angle of reflection, the angle between the reflected path and the normal to the mirror is also 36.87°.

Using trigonometry, we can find the height of the mirror required for the top of the table to be visible in the mirror. The opposite side of the angle is the height of the mirror, and the adjacent side is the distance from the mirror to the top of the table (6.4 m). Thus:

tan θ = opposite/adjacent = h/6.4

h = 6.4 × tan 36.87° = 4.5 m

To know more about mirror, here

brainly.com/question/31383194

#SPJ4

Answer:

The wavelength of this wave is 1.857 m.

Step-by-step explanation:

We can use the formula:

[tex]\sf\qquad\dashrightarrow Wavelength = \dfrac{Speed\: of\: wave}{Frequency}[/tex]

where:

Substituting these values, we get:

[tex]\sf:\implies Wavelength = \dfrac{78\: m/s}{42\: Hz}[/tex]

[tex]\sf:\implies \boxed{\bold{\:\:Wavelength = 1.857\: m\:\:}}\:\:\:\green{\checkmark}[/tex]

Therefore, the wavelength of this wave is 1.857 m.

Because the human body is a holistic organism, this means that D. A negative effect in one area can affect others areas.

This is because all the components of the human body are interconnected, and any disturbance in one part may have repercussions on other parts as well.

When there is a negative effect or disturbance in one area of the body, it can indeed have repercussions on other areas. Here are a few reasons why this occurs:

Physiological Systems: The human body is composed of several physiological systems, such as the cardiovascular system, respiratory system, digestive system, and nervous system, among others.

These systems work in harmony to maintain homeostasis and support each other's functions. Disruption or dysfunction in one system can affect the functioning of other systems, as they are interdependent.

Communication Pathways: The body relies on complex communication pathways to transmit signals and information between different organs and tissues. Hormones, neurotransmitters, and electrical impulses are examples of the communication mechanisms involved.

When there is an issue in one area, it can interfere with the signaling pathways and disrupt the communication network, potentially impacting other areas that rely on these signals.

Compensation Mechanisms: The body often has built-in compensation mechanisms to adapt and maintain balance when faced with challenges or disturbances.

However, if a negative effect persists or overwhelms the compensatory abilities, it can lead to imbalances or compromises in other areas that are trying to compensate. This can manifest as symptoms or further complications.

Blood Circulation: Blood circulation plays a vital role in distributing oxygen, nutrients, and various substances throughout the body.

Any disruption in blood flow, such as blockages or decreased perfusion, can affect multiple organs and tissues, as they rely on a steady supply of oxygen and nutrients for proper functioning.

To learn more about circulation, refer below:

https://brainly.com/question/16144348

#SPJ11

The value of the rate of flow of heat through the insulating fiber glass slab is 196 W.

The quantity of heat that is transmitted through a material per unit of time is known as the rate of heat flow and is often expressed in watts (joules per second).

The term "heat flow" is redundant because heat is the movement of thermal energy caused by thermal non-equilibrium.

Area of the fiber glass slab, A = 1.4 m²

Temperature of the fiber glass, T₁ = 175°C

Temperature outside, T₂ = 35°C

Thermal conductivity of the fiberglass, k = 0.04 Wm⁻¹K⁻¹

Thickness of the fiberglass, d = 0.04 m

The expression for the rate of flow of heat through the insulation is given by,

Q/t = kAΔT/d

Q/t = 0.04 x 1.4 x (175 - 35)/0.04

Q/t = 1.4 x 140

Q/t = 196 W

To learn more about heat flow, click:

https://brainly.com/question/30888604

#SPJ12

The shortest plane mirror in which you can see your entire image is typically half your body's height, assuming that the mirror is positioned vertically and you are standing in front of it.

When you stand in front of a plane mirror, the mirror reflects the light rays that hit it, creating a virtual image. The virtual image appears to be behind the mirror and is the same size as the object being reflected.

To see your entire image in the mirror, you need to position yourself in such a way that the top of your head and the bottom of your feet are both within the field of view of the mirror. Therefore, the height of the mirror should be at least equal to your body height.

However, if you position the mirror at an angle or tilt it, you may be able to see your entire image in a mirror that is shorter than half your body height. The angle and orientation of the mirror will affect the field of view and the visibility of your image.

It's important to note that this measurement assumes an average human body height and a mirror that is positioned vertically. Individual variations in height and the specific arrangement of the mirror can affect the minimum height of the mirror needed to see your entire image.

To know more about virtual image refer here

https://brainly.com/question/13197137#

#SPJ11

They are the same - the sweep out the same angular displacement (radians or degrees) in the same amount of time. Option A

Angular velocity is how we measure how fast an object is rotating around an axis. It can be identifies with the symbol omega (ω) and has units of radians per second (rad/s).

Angular velocity may also be see as the rate of change of the angular position of an object with respect to time.

The formula used in calculatin it is

ω = Δθ/Δt

Find more exercises on angular velocity,;

https://brainly.com/question/12446100

#SPJ1

The new research framework of Alzheimer is one that is based on biomarkers that are set into different pathologic processes of Alzheimer's which is then measured in living people with the use of imaging technology as well as analysis of cerebral spinal fluid samples.

Research suggests that inflammation in the brain may lead to AD by forming amyloid plaques and neurofibrillary tangles. Researchers explore anti-inflammatory drugs & personalized treatment for AD.

Therefore, Using genetics and biomarkers to identify high-risk AD patients, and customizing treatment plans with drugs or therapies that target underlying factors.

Learn more about Alzheimer from

https://brainly.com/question/27414232

#SPJ1

During dilemma, a person may experience conflicting thoughts and emotions, uncertainty, anxiety, and stress. Two alternative solutions you implemented to solve the dilemma are the Pros and cons list and Seeking advice.

They may struggle to make a decision, as each option has its pros and cons. To solve a dilemma, one can consider alternative solutions, weigh their potential outcomes, and decide which one aligns better with their values, beliefs, and goals. Here are two examples of alternative solutions:

Pros and cons list: One way to solve a dilemma is by making a list of pros and cons for each option. This can help to clarify the potential benefits and drawbacks of each choice, which can help in making a more informed decision.

Seeking advice: Another way to solve a dilemma is to seek advice from a trusted friend, family member, or professional. Talking through the situation with someone else can help to gain a different perspective and see the situation from a new angle.

Ultimately, the solution to a dilemma will depend on the specific situation and the individual's unique circumstances. It's important to take the time to consider all options and their potential outcomes before making a decision.

To know more about advice refer here:

https://brainly.com/question/30874899#

#SPJ11

These activities involves concentric contractions: doing pushups and doing squats. The correct option is B and D

Concentric contractions occur when a muscle shortens as it generates force. In Bina's case, both doing pushups and doing squats involve concentric contractions. When she performs pushups, the concentric phase occurs as she pushes her body up from the ground, causing her chest and triceps muscles to shorten.

Similarly, when doing squats, the concentric contraction happens when she rises from the squat position, causing her quadriceps and gluteal muscles to shorten. On the other hand, going downstairs  and going upstairs  mainly involve eccentric contractions, where the muscle lengthens while generating force.

To know more about concentric contractions, refer here:

https://brainly.com/question/15048619#

#SPJ11

Complete question:

Bina goes downstairs to her basement, does 20 pushups and 20 squats, and then returns upstairs. which of these activities involves concentric contractions?

a. going downstairs

b. doing pushups

c. going upstairs

d. doing squats

The function of transformers in power transmission lines is to step up or step down the voltage of electrical energy being transmitted.

High voltage transmission lines use high voltages to minimize energy loss due to heat during transmission. However, this high voltage is not suitable for use in homes and businesses. Therefore, transformers are used to reduce the voltage to a safer and more manageable level for consumers. A transformer consists of two coils of wire wound around a common core.

When an alternating current flows through the primary coil, it generates a magnetic field, which induces a current in the secondary coil. By varying the number of turns in the primary and secondary coils, the transformer can step up or step down the voltage of the electrical energy being transmitted. In summary, transformers play a critical role in enabling efficient and safe transmission of electrical energy from high voltage supply lines to consumers.

To know more about transmission line, here

brainly.com/question/17144572

#SPJ4

--The complete question is, What is the function of transformers in power transmission lines between high voltage supply lines and consumers, such as households or homes?--

It would take light about 1.3 million seconds, or approximately 15.05 days, to reach Earth from a star that is 390 trillion km away.

If light travels around 10 trillion km in one year, it means that its speed is approximately 300,000 km/s.

To find out how long it would take light to reach Earth from a star that is 390 trillion km away, we need to divide the distance by the speed of light.

390 trillion km ÷ 300,000 km/s = 1,300,000 seconds

So it would take light about 1.3 million seconds, or approximately 15.05 days, to reach Earth from a star that is 390 trillion km away.

To know more about Earth, refer here:

https://brainly.com/question/31064851#

#SPJ11

The sound intensity level (SIL) of a sound source decreases as the distance from the source increases.

The relationship between the SIL and the distance from the source is given by the inverse square law:

SIL2 = SIL1 + 20 log10(d1/d2)

where SIL1 is the initial sound intensity level, d1 is the initial distance, SIL2 is the new sound intensity level, and d2 is the new distance.

In this case, we are given that the initial SIL of the rocket launch is 102 dB at a distance of 2000 m.

We want to find the new SIL at a distance of 20 m. Using the inverse square law, we have:

SIL2 = SIL1 + 20 log10(d1/d2)

SIL2 = 102 dB + 20 log10(2000 m / 20 m)

SIL2 = 102 dB + 20 log10(100)

SIL2 = 102 dB + 40

SIL2 = 142 dB

Therefore, the sound intensity level of the rocket launch from a distance of 20 m is 142 dB.

To know more about sound intensity level refer here

https://brainly.com/question/30101270#

#SPJ11