Part A

Determine the force in member DE of the truss, and state if the member is in tension or compression. Take F1 = 564 N , F2 = 905 N .
(Figure 1)

Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.

Part B

Determine the forces in members DC and CB of the truss, and state if the members are in tension or compression.

Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.

Part C

Determine the force in member CE of the truss, and state if the member is in tension or compression.

Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.

Part D

Determine the force in member EB of the truss, and state if the member is in tension or compression.

Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.

Part E

Determine the force in member EA of the truss, and state if the member is in tension or compression.

Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression.

The branch circuit conductors for a 5 hp, 230V, single-phase motor with a nameplate rating of 25 A must have an ampacity of 30 A or greater.

What is circuit?
A circuit is an interconnection of electronic components that allows electricity, signals or data to flow from one component to another. It can be as simple as a single resistor or as complex as a microprocessor. Circuits are used to provide power to devices, control signals, process data or any combination of these. Circuits can be made from components such as resistors, capacitors, transistors, integrated circuits and microprocessors.

According to the National Electrical Code (NEC), the minimum branch circuit conductor size for a 5 hp, 230V, single-phase motor with a nameplate rating of 25 A must be sized at 30 A or greater. This is because the NEC requires a branch circuit conductor to have an ampacity at least 125% of the full-load current rating of the motor.

To learn more about circuit
https://brainly.com/question/30018555

#SPJ4

The principal of the loan that TMI Systems repaid was $90,000.

The formula to calculate the principal of a loan is P = L + I, where P is the principal, L is the loan amount, and I is the total interest paid over the duration of the loan.

In this case, we are given that the loan amount was 10% per year simple interest, which can be calculated by multiplying the principal by the interest rate (0.1) and the duration of the loan (5 years). Therefore, the total interest paid over the duration of the loan is P x 0.1 x 5 = $50,000.

We are also given the total amount repaid, which is the sum of the principal and the total interest paid. Therefore, we can calculate the principal by subtracting the total interest paid from the total amount repaid.

This gives us $140,000 - $50,000 = $90,000. As the principal must be a positive value, the principal of the loan is $90,000.

For more questions like Principal click the link below:

https://brainly.com/question/17960115

#SPJ4

You would expect each of the following to have a lower p50 qualitative effect on hemoglobin (5 pts) a) Raising the pH from 7.0 to 7.4.

On the forecasts, there is a "qualitative influence." Reliability and accuracy are two characteristics of forecasts. The dependability or accuracy of the forecasts may improve or worsen, depending on the qualitative effect.

Acitric Acids As an illustration, amino acid monomers make up proteins. A functional protein is created by folding a chain of linked polypeptides into a three-dimensional (3D) structure.

To know more about qualitative effect on hemoglobin visit :-

https://brainly.com/question/30216819

#SPJ4

The procedure is as follows in C++: double base calcPyramidVolume. Length, two bases. Double pyramid, width, Height.

The parameter variable for the following function prototype has a data type of double. Using the C double data type, high-precision floating-point data or integers are saved (up to 15 to 17 digits). There are large decimal number values recorded. In comparison to float data, values data may store twice as much information. As a result, it is referred to as a double data type. The double data type of the C programming language is used to store high-precision floating-point data or integers in computer memory. The double data type is so named because it can hold data that is twice as large as the float data type. Eight bytes, or 64 bits, make up a double.

Learn more about Double data type here:

https://brainly.com/question/29846304

#SPJ4

Answer:

B

Explanation:

Aluminium doesn't rust unless exposed to copper for a duration of time.

The letters A to H on the blank, 'A' being the first step, and so on is as follows:

8-F, 9-E, 10-B, 11-C, 12-G, 13.D 14.A

In mathematics, a sequence is an ordered list of objects where repetitions are allowed. It has members and is comparable to a set (also called elements, or terms). The number of elements determines the length of the sequence (possibly infinite). In contrast to a set, the same elements can appear multiple times in a sequence at different positions, and unlike a set, the order matters.

Formally, a sequence can be defined as a function from natural numbers (the positions of the sequence's elements) to the elements at each of those positions. You can think of an indexed family, which is a function from any index set, as a generalisation of the concept of a sequence.

Learn more about sequence

https://brainly.com/question/21961097

#SPJ4

It is TRUE that the Tactical ventilation should be performed only when the fire attack hoselines and teams are ready to advance toward the fire.

What is Tactical ventilation?

Through purposeful flow path management, the overarching goal of all forms of tactical ventilation is to improve interior tenability for occupants and firefighters.

Flow path management for control and extinguishment is best accomplished by placing ventilation openings as close to the source fire as possible (e.g., not in a remote location) and working in collaboration with the fire attack team (e.g., vent ahead of rather than behind the attack team).

Firefighters must constantly control their environment with hose stream techniques when using ventilation tactics and interior attack to cool and dilute the highly combustible smoke.

To know more about Tactical ventilation, visit: https://brainly.com/question/27841064

#SPJ4

Answer:

Who care

Explanation:

Lol

Answer:

the correct answer is option B. W

Answer:

it is b and w

Explanation:

pls mark as brainlist

Answer:

Dependent Variable: Academic achievement

Independent Variable: After school programs

Answer: true

Explanation:

Given statement: smiles.substring(1, 5) returns "mile". This assertion absolutely is true.

In the try block, we transform the string to a Double using the parseDouble() method of Double to determine whether the text solely contains integers. The string isn't a number if it throws an error (such as a NumberFormatException fault), in which case numeric is set to false. It is a number if not.

Similar to declaring a one-dimensional array, a string can be declared easily.  size[char str name]; In the aforementioned syntax, size is used to specify the string's length, or the amount of characters it may hold. Str name is any name supplied to the string variable.

To learn more about string visit:

brainly.com/question/30099412

#SPJ1

For gas piping other than black or galvanized steel installed in a concealed location, where a bored hole is located a maximum of 1/2 inch from the edge of the wood member.

What is galvanized steel?
Galvanized steel is a type of steel that has been treated with a layer of zinc oxide to protect it from corrosion. This layer is bonded to the steel so that it will not flake or peel off. Galvanized steel is often used in the construction industry because it is highly resistant to rust and other forms of corrosion. It is also used in the automotive and appliance industries as well as in the production of water pipes, fencing, and other metal items. Galvanized steel is cost-effective and easy to maintain, making it a popular choice for many applications. It is also environmentally friendly since it does not require the use of chemicals or paints. Galvanized steel is a durable and versatile material that is essential for many projects.

To learn more about galvanized steel
https://brainly.com/question/14835168

#SPJ4

The function that causes values of both x and to develop the highest feasible moment at A according to the provided suspended mass is written as 14715 Nm (clockwise).

The quantity of matter or substance that makes up a thing is known as its mass. The unit of measurement is the kilogramme, abbreviated as kg. It's crucial to keep in mind that mass differs from weight. While weight varies with changes in gravity, mass never changes.

We have identified the following values,

adjust for any angle 00 ≤ θ ≤ 900 any extension 0 ≤ x ≤ 5 m.

So,

Let us consider an equation to calculate the moment using θ and x as variables around point A.

⇒ ((9−1.5) + x) (cosθ) (120) (9.81)

When we are simplifying the given equation gives us:

⇒ MA ​= (7.5+x) 1177.2 cosθ

Here the maximum moment will develop if θ = 0 and x=5 m.

Then, by substituting these values gives us:

⇒ MA​=(7.5+x)1177.2cosθ

⇒ MA​=(7.5+5)1177.2cos00

Thus, the value of MA is written as, 14715 Nm (clockwise)

To learn more about the mass, follow the link;

https://brainly.com/question/19694949

#SPJ1

The shear plane angle is calculated as 49.4 degrees while the shear strain is given as 1.17

Shear strain is a measure of deformation resulting from an applied force that is parallel to the surface of an object. It is usually expressed as a fractional change in the length of the object. Shear strain is a measure of the displacement of the surface points of an object in the direction perpendicular to the direction of the applied force.

The shear plane angle is the angle between the plane of shear stress and the normal to the plane of shear. It is typically measured in degrees and can range from 0 to 90 degrees.

(a) Shear plane angle = tan⁻¹((0.65-0.30)/0.30) = 49.4°

(b) Shear strain = (deformed chip thickness - initial chip thickness)/initial chip thickness

Substituting the values into the formula;

Shear Strain = (0.65-0.30)/0.30 = 1.17

learn more on shear strain here;

https://brainly.com/question/22714442

#SPJ1

An inverter or ac module is required to automatically switchover its output when utility power is lost.

What is an inverter?
An inverter is an electrical device that converts direct current (DC) to alternating current (AC). It is a type of power electronic converter that is used to convert low-voltage DC electricity from sources such as batteries or solar panels into a higher voltage AC output. Inverters allow for the use of DC power sources such as batteries to power AC appliances, and are commonly used in recreational vehicles and off-grid energy systems. They are also used in adjustable speed drives, uninterruptible power supplies, and in many consumer electronics applications. Inverters come in a variety of sizes ranging from small microcontrollers that control a single appliance, to large industrial models that are used to power entire buildings.

To learn more about inverter
https://brainly.com/question/28086004

#SPJ4

Using the formula of shear stress, the minimum required diameter is 0.81mm

Shear stress is a force that causes two objects to slide past each other in opposite directions. It is the force per unit area of the surface on which the force is applied. Shear stress is often caused by two objects rubbing against each other, such as a car tire sliding on the road. It can also be caused by wind, gravity, or other forces.

The shear stress on the shaft can be calculated using the formula:

τ(allow) = P/(2*π*d*J)

where P is the total power transferred by the shaft, d is the diameter of the shaft, and J is the polar moment of inertia.

J = π*d⁴/32

Substituting the given values,

τ(allow) = (15 + 6 + 4 + 5)/(2*π*d*π*d⁴/32)

d = √[32*(15 + 6 + 4 + 5)/(τ(allow)*2*π²)]

d = √[32*(30)/(75*2*π²)]

d = 0.81mm

The minimum required diameter of the shaft is 0.81 mm to the nearest millimeter.

Learn more shear stress here;

https://brainly.com/question/13670232

#SPJ1

Answer:

Terms in this set (18)

Original

Which agency is responsible for managing Florida's hunting laws and regulations?

*The Fish & Wildlife Conservation Commission

*The US Fish & Wildlife Service

*The International Hunter Education Association

*The National Rifle Association

The Fish & Wildlife Conservation Commission

How are laws and regulations different from one another?

*Laws are long-standing, while regulations can be modified quickly

*Laws can be modified quickly, while regulations are long-standing

*Laws are governed by the federal government while regulations are governed by the state government

*Violators of laws are taken to criminal court while violators of regulations are taken to civil court.

Laws are long-standing, while regulations can be modified quickly

Why were hunting laws and regulations initially enacted?

*To help market hunters get enough game to survive

*To protect wildlife from over hunting and market hunting

*To help hunters get a fair price for food from wild game

*To protect wildlife from fair chase and conservation efforts

To protect wildlife from over hunting and market huntingExplanation:

2500 : 3

To solve this, let's build some relationships among the power, voltage, current and number of loops in an ideal transformer.

For an ideal transformer, the powers generated by the primary and secondary coils are the same. In other words, the input power and output power remain the same.

Input power = Output power

Where;

Input power = [tex]V_{p}[/tex] x [tex]I_p[/tex]

Output power = [tex]V_{s}[/tex] x [tex]I_s[/tex]

=> [tex]V_{p}[/tex] x [tex]I_p[/tex] = [tex]V_{s}[/tex] x [tex]I_s[/tex]

This can be re-written as:

[tex]\frac{V_p}{V_s}[/tex] = [tex]\frac{I_s}{I_p}[/tex]             ------------------(i)

Also, the transformer turns ratio (r) is the quotient of the number of turns/loops in the primary coil and the number of turns/loops in the secondary coil. i.e

r = [tex]\frac{N_p}{N_s}[/tex]

This ratio is equal to the ratio given in equation (i) i.e

r = [tex]\frac{N_p}{N_s}[/tex] = [tex]\frac{V_p}{V_s}[/tex] = [tex]\frac{I_s}{I_p}[/tex]

=> r = [tex]\frac{N_p}{N_s}[/tex] = [tex]\frac{V_p}{V_s}[/tex]

=> [tex]\frac{N_p}{N_s}[/tex] = [tex]\frac{V_p}{V_s}[/tex]

This can be re-written as

=> [tex]\frac{N_s}{N_p}[/tex] = [tex]\frac{V_s}{V_p}[/tex]       -----------(ii)

From the question,

[tex]V_{p}[/tex] = 120V

[tex]V_{s}[/tex] = 100kV = 100000V

Substitute these values into equation (ii) as follows;

[tex]\frac{N_s}{N_p}[/tex] = [tex]\frac{100000}{120}[/tex]

[tex]\frac{N_s}{N_p}[/tex] =  [tex]\frac{10000}{12}[/tex]

[tex]\frac{N_s}{N_p}[/tex] =  [tex]\frac{2500}{3}[/tex]

Therefore, the ratio of the number of loops in the secondary to the number of loops in the primary is 2500 : 3

Answer: true

Explanation: I haves

Answer:

a)  Cr = Co - Fx / D

b)   ΔC / Δx = ( CR - Cr )  / ( xR - xRo )

Explanation:

A) Derive an expression for the profile c(r) inside the tissue

F = DΔC / X  = D ( Co - Cr ) / X   ------ 1

where : F = flux , D = drug diffusion coefficient

            X = radial distance between Ro and R

Hence : Cr = Co - Fx / D

B) Express the diffusive flux at outer surface of the balloon

Diffusive flux at outer surface =  ΔC / Δx = CR - Cr / xR - xRo

The size of RHW copper conductors needed for this 3-phase, 240-volt load is 4/10 AWG.

Copper conductors are electrical wires composed of copper that are used to carry electrical currents. They are used in a variety of applications, including power generation and transmission, electronics, telecommunications, and consumer products. Copper is an ideal material for electrical conductors because it is highly conductive, durable, and cost-effective. Copper conductors are available in a range of sizes and shapes and are used in both residential and commercial settings.

This is based on the National Electrical Code (NEC) Table 310.15(B)(16), which states that the minimum size for a 196 ampere load is 4/10 AWG for three insulated conductors in an EMT conduit.

To learn more about copper conductors
https://brainly.com/question/14941254
#SPJ4

According to the question, net use \\Romulus\AlbaLonga is the correct syntax.

What is syntax?
Syntax is the set of rules and principles that govern the structure of sentences in a given language. It is a component of grammar that focuses on the arrangement of words and phrases to form correct sentences. Syntax helps to determine the meaning of a sentence and provides clarity for the reader. Syntax also plays an important role in writing, as it helps to create coherent and effective sentences that convey the right message. Syntax is a complex subject and involves the use of a variety of terms such as syntax, morphology, semantics, and pragmatics. Syntax also includes the use of punctuation and other stylistic devices. By understanding syntax, one can learn how to properly construct sentences, enabling them to communicate effectively in writing.

To learn more about syntax
https://brainly.com/question/14398309

#SPJ4

The structural number of the pavement, constructed with 5 inches of the sand-mix asphaltic wearing surface is 14.5.

The structural number is an estimate of the number of inches of asphaltic wearing surface that a pavement can support without exceeding the allowable structural layer strain. It is calculated by multiplying each layer's drainage coefficient by its thickness and then adding the products together.

T In this case, the 5-inch wearing surface has a drainage coefficient of 0.90, the 9-inch base has a coefficient of 1.0, and the 10-inch subbase has a coefficient of 1.0.

The structural number can be calculated by using the following formula:

SN = (5 x 0.90) + (9 x 1.0) + (10 x 1.0) = 14.5. Therefore, the structural number of the pavement is 14.5.

For more questions like Pavement click the link below:

https://brainly.com/question/14452903

#SPJ4

The Pilot Car is the vehicle that alerts drivers to oversized loads. So, the correct answer to the question is a. Pilot car.

What exactly is a Pilot Car?

A pilot car is a vehicle that is used to guide and support convoys of large vehicles or trucks carrying heavy loads. Pilot cars can be sedans, SUVs, vans, or pickup trucks and must be equipped with lights, flags, and a CB radio in order to communicate with the oversized vehicle. ‍

To know more about Pilot Cars, visit: https://brainly.com/question/30002465

#SPJ4

The router will be informed of the appropriate host ID by the last octet, which is the octet of the sub-net mask 255.255.255.0.

In the IPv4 component of the address, one octet is referred to as x and is a decimal value between 0 and 255. Periods are used to separate the octets. Three periods and four octets are required in the IPv4 component of the address. People may have also heard the term "octets" used to describe the four numbers that make up an IP address. The right name for the four distinct digits that make up an IP address is an octet. The third octet of sub-netting is used to specify specific sub nets of network 150.150.0.0. In the example in the image, each sub-net number has a different value in the third byte, signifying that it is a separate sub-net number.

Learn more about Octets here:

https://brainly.com/question/28276191

#SPJ4

Answer:

112.5 watts

Explanation:

The output voltage (V) = 15 volts

The equivalent resistance for the speakers connected in parallel ([tex]R_T[/tex]) is gotten by using the formula:

[tex]\frac{1}{R_T}=\frac{1}{R_1}+\frac{1}{R_2}+\frac{1}{R_3}+\frac{1}{R_4}\\\\But\ R_1=R_2=R_3=R_4=8\ ohm\\\\\frac{1}{R_T} =\frac{1}{8} +\frac{1}{8} +\frac{1}{8} +\frac{1}{8} \\\\\frac{1}{R_T} =\frac{1+1+1+1}{8} \\\\\frac{1}{R_T} =\frac{4}{8} \\\\R_T=\frac{8}{4} \\\\R_T=2\ ohm[/tex]

The current flowing through the amplifier (I) is:

I = V / [tex]R_T[/tex] = 15 / 2 = 7.5 A

The audio power (P) when outputting this maximum voltage is given by:

P = V² / [tex]R_T[/tex] = I²[tex]R_T[/tex]. Therefore:

P = V² / [tex]R_T[/tex] = 15² / [tex]R_T[/tex] = 112.5 watts

The motor feeder conductor size for the described system would be 4 AWG aluminum THHN rated for a 75-degree C temperature.

The total horsepower for the three-phase motors is 45 hp and the total horsepower for the single-phase motors is 4 hp. The total horsepower is then 49 hp.

The next step is to calculate the load in amps as follows:

(49 hp x 746 watts)/(208 volts x 1.25 efficiency factor)

= 177 amps.

With 177 amps as the total load, the next step is to select the conductor size using the NEC Table 310.16. A 4 AWG aluminum THHN conductor is rated for a maximum of 195 amps.

For more questions like Conductor click the link below:

https://brainly.com/question/29360867

#SPJ4

Answer:

The correct answer will be "1477.84 N".

Explanation:

Given that,

Mass,

m = 1.6 mg

or,

   = 1600 kg

Initial velocity,

u = 72 km/h

  = [tex]72\times \frac{5}{18} \ m/s[/tex]

  = [tex]20 \ m/s[/tex]

Final velocity,

v = 18 km/h

  = [tex]18\times \frac{5}{18}[/tex]

  = [tex]5 \ m/s[/tex]

Covered distance,

s = 250 m

By using the below relation, we get

⇒  [tex]v^2=u^2+2as[/tex]

On putting the values, we get

⇒  [tex](5)^2=(20)^2+2\times a\times 250[/tex]

⇒      [tex]a=-0.75 \ m/s^2[/tex] (shows the deceleration)

Slope will be given as 1 in 25, then

⇒  [tex]Sin \theta=\frac{1}{25}[/tex]

           [tex]\theta=2.3^{\circ}[/tex]

hence,

As we know,

⇒  [tex]\Sigma F=ma[/tex]

or,

⇒  [tex]Braking \ force+350-mgSin\theta=ma[/tex]

⇒  [tex]Braking \ force=ma+mgSin\theta-350[/tex]

On substituting all the values, we get

⇒                           [tex]=1600(0.75+1600\times 9.81 Sin(2.3^{\circ})-350[/tex]

⇒                           [tex]=1477.84 \ N[/tex]