Answer: a. The acceleration of the proton is 5.85 × 10^14 m/s2.
b. The time interval to reach the speed of 1.60 × 10^6 m/s= 2.74 × 10^-9 s.
c. The proton moves a distance of 1.38 × 10^-5 m.
d. kinetic energy at the end of the interval is 2.56 × 10^-12 J.
Electric field = 610 N/c,
Initial velocity, u = 0 m/s,
Final velocity, v = 1.6 × 106 m/s
(a) Acceleration of the proton: The force acting on the proton = qE where q is the charge of the proton.
Therefore, ma = qE where m is the mass of the proton.
The acceleration of the proton, a = qE/m.
Here, the charge of the proton, q = +1.6 × 10^-19 C, The mass of the proton, m = 1.67 × 10^-27 kg. Substituting the values in the equation, we get, a = 1.6 × 10^-19 C × 610 N/C ÷ 1.67 × 10^-27 kg. a = 5.85 × 10^14 m/s^2
(b) Time taken to reach this speed: We know that, v = u + at. Here, u = 0 m/s, v = 1.6 × 106 m/s, a = 5.85 × 1014 m/s2. Substituting the values, we get,1.6 × 106 = 0 + 5.85 × 10^14 × tt = 1.6 × 106 ÷ 5.85 × 10^14 s= 2.74 × 10^-9 s
(c) Distance travelled by the proton: The distance travelled by the proton can be calculated using the equation,v^2 = u^2 + 2asHere, u = 0 m/s, v = 1.6 × 106 m/s, a = 5.85 × 10^14 m/s2Substituting the values, we get,1.6 × 10^6 = 0 + 2 × 5.85 × 10^14 × s. Solving for s, we get, s = 1.38 × 10^-5 m.
(d) Kinetic energy of the proton: At the end of the interval, the kinetic energy of the proton, KE = (1/2)mv^2 Here, m = 1.67 × 10^-27 kg, v = 1.6 × 10^6 m/s. Substituting the values, we get, KE = (1/2) × 1.67 × 10^-27 × (1.6 × 10^6)^2JKE = 2.56 × 10^-12 J.
Therefore, the acceleration of the proton is 5.85 × 10^14 m/s2.
The time interval to reach the speed of 1.60 × 10^6 m/s is 2.74 × 10^-9 s.
The proton moves a distance of 1.38 × 10^-5 m.
kinetic energy at the end of the interval is 2.56 × 10^-12 J.
Learn more about proton : https://brainly.com/question/1481324
#SPJ11
A 2002 lamp and a 30 02 lamp are connected in series with a 10 V battery. Calculate the following: the voltage drop across the 20 2 lamp Question 20 1 pts A 2002 lamp and a 30 02 lamp are connected in series with a 10 V battery. Calculate the following: the voltage drop across the 300 lamp
The voltage drop across the 20 2 lamp is approximately 3.32 V, and the voltage drop across the 300 lamp is approximately 6.68 V.
When two lamps are connected in series, they share the same current. The voltage drop across the two lamps is proportional to their resistance, which can be calculated using Ohm's Law. We can use the equation:V = IR,where V is voltage, I is current, and R is resistance. Given that the two lamps are connected in series with a 10 V battery, we know that the voltage drop across the two lamps will be 10 V. We can use this information to find the resistance of the two lamps combined.
Using Ohm's Law:10 V = I(R1 + R2),where R1 and R2 are the resistances of the two lamps, and I is the current flowing through the circuit. Since the two lamps share the same current, we can say that I is the same for both lamps. Therefore, we can rewrite the equation as:10 V = I(R1 + R2)orI = 10 / (R1 + R2)To find the voltage drop across each lamp, we can use the equation:V = IR. For the 2002 lamp, we know that R1 = 2002 Ω. For the 30 02 lamp, we know that R2 = 3002 Ω. We can substitute these values into the equation:V1 = IR1V1 = (10 / (2002 + 3002)) * 2002V1 ≈ 3.32 VFor the 300 lamp, we can use the same equation:V2 = IR2V2 = (10 / (2002 + 3002)) * 3002V2 ≈ 6.68 VTherefore, the voltage drop across the 20 2 lamp is approximately 3.32 V, and the voltage drop across the 300 lamp is approximately 6.68 V.
Learn more about Equation here,What is equation? Define equation
https://brainly.com/question/29174899
#SPJ11
What happens to a circuit's resistance (R), voltage (V), and current (1) when
you change the thickness of the wire in the circuit?
A. V and I will also change, but R will remain constant.
B. R and I will also change, but V will remain constant.
O C. R, V, and I will all remain constant.
OD. R and V will also change, but I will remain constant.
When you change the thickness of the wire in a circuit, option B. the resistance (R) and current (I) will also change, but the voltage (V) will remain constant.
The resistance of a wire is directly proportional to its length and inversely proportional to its cross-sectional area (thickness). As the thickness of the wire changes, the cross-sectional area changes, which in turn affects the resistance. Thicker wires have a larger cross-sectional area, resulting in lower resistance, while thinner wires have a smaller cross-sectional area, resulting in higher resistance. Therefore, changing the thickness of the wire will cause a change in resistance.
According to Ohm's Law (V = IR), the voltage (V) in a circuit is equal to the product of the current (I) and the resistance (R). If the voltage is kept constant, and the resistance changes due to the thickness of the wire, the current will also change to maintain the relationship defined by Ohm's Law. When the resistance increases, the current decreases, and vice versa.
However, it's important to note that changing the thickness of the wire will not directly affect the voltage. The voltage in a circuit is determined by the power source or the potential difference applied across the circuit and is independent of the wire thickness. As long as the voltage source remains constant, the voltage across the circuit will remain constant regardless of the wire thickness. Therefore, the correct answer is option B.
know more about current here:
https://brainly.com/question/1100341
#SPJ8
A gun is fired vertically into a block of wood (mass ml) at rest directly above it. If the bullet has a mass of m2 and a speed of v, how high will the block rise into the air after the bullet becomes embedded in it?
Answer: the height to which the block will rise into the air after the bullet becomes embedded in it is given by
H = (m₂v)² / 2(m₁ + ml)g.
When a gun is fired vertically into a block of wood at rest directly above it, the velocity of the block can be calculated by applying the law of conservation of momentum. Here, the bullet of mass m₂ is fired into the block of wood of mass ml. According to the law of conservation of momentum, the initial momentum of the bullet and the final momentum of the bullet and the block combined must be equal, and it can be expressed as:m₂v = (m₁ + ml)VWhere V is the velocity of the bullet and the block combined.
From the equation, we have: V = m₂v / (m₁ + ml)As the bullet and the block rise to a maximum height H, their total energy is equal to their initial kinetic energy, given as: 1/2 (m₁ + m₂) V² = (m₁ + m₂)gh. Where g is the acceleration due to gravity. Solving for H, we get: H = V² / 2g
Substituting the value of V in the above equation, we have: H = (m₂v)² / 2(m₁ + ml)g.
Therefore, the height to which the block will rise into the air after the bullet becomes embedded in it is given by H = (m₂v)² / 2(m₁ + ml)g.
Learn more about momentum: https://brainly.com/question/1042017
#SPJ11
Water is poured into a U-shaped tube. The right side is much wider than the left side. Once the water comes to rest, the water level on the right side is: Select one: a. the same as the water level on the left side. b. higher than the water level on the left side. c. lower than the water level on the left side.
The correct answer is the same as the water level on the left side. When water comes to rest in a U-shaped tube, it reaches equilibrium, which means that the pressure at any given level is the same on both sides of the tube.
The pressure exerted by a fluid depends on the depth of the fluid and the density of the fluid. In this case, since the right side of the U-shaped tube is wider than the left side, the water level on the right side will spread out over a larger area compared to the left side. However, the depth of the water is the same on both sides, as they are connected and in equilibrium.
Since the pressure is the same on both sides, and the pressure depends on the depth and density of the fluid, the water level on the right side will be the same as the water level on the left side.
Therefore, option a. "the same as the water level on the left side" is the correct answer.
Learn more about pressure here:
https://brainly.com/question/857286
#SPJ11
A cube is 2.0 cm on a side when at rest. (a) What shape does it
take on when moving past an observer at 2.5 x 10^8 m/s, and (b)
what is the length of each side?
Answer: The length of each side of the cube when moving past an observer at 2.5 x 10^8 m/s is 1.22 cm.
The question is asking us to consider the relativistic effect of time dilation and length contraction, which affect the measurement of distance and time by a moving observer. Therefore, the apparent length and shape of the cube will differ from the actual measurements as seen by an observer at rest.
a) When the cube moves past an observer at a velocity of 2.5 x 10^8 m/s, it takes on a shape that is flattened in the direction of motion. This is because of the relativistic effect of length contraction. This effect states that the length of an object appears shorter to an observer in motion than to an observer at rest.
The degree of length contraction increases with velocity and is given by the formula: L' = L₀ / γ
where L₀ is the length at rest, L' is the apparent length observed by a moving observer, and γ is the Lorentz factor given by :
γ = 1 / √(1 - v²/c²) where v is the velocity of the cube and c is the speed of light.
Substituting the values, we have:
L' = 2.0 cm / γL'
= 2.0 cm / √(1 - (2.5 x 10^8 m/s)²/(3.0 x 10^8 m/s)²)L'
= 0.47 cm.
b) The length of each side of the cube when moving past an observer at 2.5 x 10^8 m/s is given by: L' = L₀ / γL = L' x γSubstituting the values, we have:
L = L' x γL
= 0.47 cm x √(1 - (2.5 x 10^8 m/s)²/(3.0 x 10^8 m/s)²)L
= 1.22 cm.
Thus, the length of each side of the cube when moving past an observer at 2.5 x 10^8 m/s is 1.22 cm.
Learn more about time dilation : https://brainly.com/question/3747871
#SPJ11
At some instant the velocity components of an electron moving between two charged parallel plates are v x
=1.6×10 5
m/s and v y
=3.5×10 3
m/s. Suppose the electric field between the plates is uniform and given by E
=(120 N/C) j
^
. In unit-vector notation, what are (a) the electron's acceleration in that field and (b) the electron's velocity when its x coordinate has changed by 2.4 cm ?
Therefore, we have vy = vy,0 + ayt = (3.5 x 10^3 m/s) + (7.21 x 10^17 m/s^2)(1.5 x 10^-7 s) = 3.508 m/s. Thus, the electron's velocity when its x-coordinate has changed by 2.4 cm is v = (1.6 x 10^5 m/s)i + 3.508 m/sj. The required answer in unit-vector notation is v = (1.6 x 10^5 m/s)i + 3.508 m/sj. The solution has been presented in more than 150 words.
(a) To find the acceleration of the electron in the given electric field, we will use the formula F = ma, where F is the force acting on the electron, m is its mass, and a is its acceleration. The force acting on the electron due to the electric field is given by F = qE, where q is the charge of the electron and E is the electric field. Therefore,
we have F = (1.6 x 10^-19 C)(120 N/C)j = 1.92 x 10^-17 Nj.Using Newton's second law, F = ma, we can find the acceleration of the electron as a = F/m = (1.92 x 10^-17 Nj)/(9.11 x 10^-31 kg) = 2.1electron's1 x 10^13 m/s^2. Therefore, the electron's acceleration in the given electric field is a = 2.11 x 10^13 j m/s^2.
(b) To find the electron's velocity when its x-coordinate changes by 2.4 cm, we will first find the time taken by the electron to move this distance. The x-component of the electron's velocity is given as vx = 1.6 x 10^5 m/s, so we have x = vxt => t = x/vx = (2.4 x 10^-2 m)/(1.6 x 10^5 m/s) = 1.5 x 10^-7 s.
The acceleration of the electron in the y-direction is given by ay = Fy/m = (qEy)/m = (1.6 x 10^-19 C)(3.5 x 10^3 m/s)(120 N/C)/(9.11 x 10^-31 kg) = 7.21 x 10^17 m/s^2. Since the acceleration is constant, we can use the kinematic equation vy = u + at, where u is the initial velocity in the y-direction, to find the final velocity of the electron in the y-direction. The initial velocity vy,0 in the y-direction is given as vy,0 = 3.5 x 10^3 m/s, and the time t is 1.5 x 10^-7 s.
Therefore, we have vy = vy,0 + ayt = (3.5 x 10^3 m/s) + (7.21 x 10^17 m/s^2)(1.5 x 10^-7 s) = 3.508 m/s. Thus, the electron's velocity when its x-coordinate has changed by 2.4 cm is v = (1.6 x 10^5 m/s)i + 3.508 m/sj. The required answer in unit-vector notation is v = (1.6 x 10^5 m/s)i + 3.508 m/sj. The solution has been presented in more than 150 words.
to know more about electron
https://brainly.com/question/14388606
#SPJ11
Which will not be affected by the induced e.m.f when a magnet is in motion relative to a coil? A. Motion of the magnet B. Resistance of the coil C. Number of turns of the coil D. The strength of the magnet pole
The strength of the magnet pole (option D) will not be affected by the induced electromotive force (e.m.f) when a magnet is in motion relative to a coil.
When a magnet is in motion relative to a coil, it induces an electromotive force (e.m.f) in the coil due to the changing magnetic field. This induced e.m.f. can cause various effects, but it does not directly affect the strength of the magnet pole (option D). Option A, the motion of the magnet, is directly related to the induction of the e.m.f. When the magnet moves, the magnetic field through the coil changes, inducing the e.m.f.
Option B, the resistance of the coil, affects the amount of current flowing through the coil when the e.m.f is induced. Higher resistance can limit the current flow. Option C, the number of turns of the coil, affects the magnitude of the induced e.m.f. More turns increase the induced voltage.
However, the strength of the magnet pole (option D) itself is independent of the induced e.m.f. It is determined by the properties of the magnet, such as its magnetization and magnetic material. The induced e.m.f does not alter the intrinsic strength of the magnet pole.
Learn more about electromotive force here:
https://brainly.com/question/13753346
#SPJ11
A 3-phase electrical device connected as a Y circuit with each phase having a resistance of 25 ohms. The line voltage is 230 volts.
a. What is the phase current??
In a Y-connected circuit, the line voltage (V_line) is equal to the phase voltage (V_phase). Therefore, the line voltage is 230 volts. The phase current in the Y-connected circuit is 9.2 Amperes.
To calculate the phase current (I_phase), we need to use Ohm's Law. Ohm's Law states that the current (I) flowing through a resistor is equal to the voltage (V) across the resistor divided by the resistance (R).
In this case, the resistance of each phase is given as 25 ohms. Since the line voltage (V_line) is equal to the phase voltage (V_phase), we can use the line voltage in the calculation.
Using Ohm's Law: I_phase = V_phase / R_phase
Since V_line = V_phase, we can substitute the values: I_phase = V_line / R_phase
Substituting V_line = 230 volts and R_phase = 25 ohms, we get:
I_phase = 230 V / 25 Ω = 9.2 Amperes
Therefore, the phase current in the Y-connected circuit is 9.2 Amperes.
To know more about phase current click here:
https://brainly.com/question/19578744
#SPJ11
Water runs into a fountain, filling all the pipes, at a steady rate of 0.753 m3/s. How fast will it shoot out of a hole 4.42 cm in diameter? Express your answer in meters per second
At what speed will it shoot out if the diameter of the hole is three times as large? Express your answer in meters per second.
Water runs into a fountain, filling all the pipes, at a steady rate of 0.753 m3/s.(a)The speed of water shooting out of a hole with a diameter of 4.42 cm is 4.43 m/s.(b) The speed of water shooting out of a hole with a diameter that is three times as large is 7.07 m/s.
(a)The gravitational constant is 9.8 m/s^2, so the velocity of efflux is equal to:
v = sqrt(2 × 9.8 m/s^2) = 4.43 m/s
The diameter of the hole is 4.42 cm, which is 0.0442 m. The area of the hole is then equal to:
A = pi× r^2 = pi × (0.0442 m / 2)^2 = 5.27 × 10^-5 m^2
The volume flow rate is equal to the area of the hole multiplied by the velocity of efflux, so the volume flow rate is:
Q = A × v = 5.27 × 10^-5 m^2 × 4.43 m/s = 2.37 × 10^-4 m^3/s
Therefore, the speed of water shooting out of a hole with a diameter of 4.42 cm is 4.43 m/s.
(b)If the diameter of the hole is three times as large, then the area of the hole will be nine times as large. The volume flow rate will then be nine times as large, or 2.14 × 10^-3 m^3/s.
Therefore, the speed of water shooting out of a hole with a diameter that is three times as large is 7.07 m/s.
To learn more about volume flow rate visit: https://brainly.com/question/30618961
#SPJ11
What is the capacitance of a parallel plate capacitor with plates that have an area of 3.97 m’ and are separated by a distance of 0.066 mm (in vacuum, use K 1)? Remember that co 8.25 x 10 12 c²/Nm² *Provide exponential answers in the format. EU (CE 1.85 x 10-12 8.85E-12)
The capacitance of a parallel plate capacitor with plates having an area of 3.97 m² and separated by a distance of 0.066 mm (in vacuum) is approximately [tex]1.85\times10^{-12}\ \text{F}[/tex]
The capacitance of a parallel plate capacitor is given by the formula [tex]C = (\varepsilon_0A) / d[/tex], where C represents capacitance, ε₀ represents the permittivity of free space, A represents the area of the plates, and d represents the distance between the plates.
Given values:
A = 3.97 m² (plate area)
d = 0.066 mm =[tex]0.066\times10^{-3}\ \text{m}[/tex] (plate separation in meters)
ε₀ =[tex]8.85 \times 10^{-12}\ \text{C}^{2}/\text{N}\text{m}^{2}[/tex] (permittivity of free space)
Substituting these values into the capacitance formula, we get:
C = (ε₀A) / d = [tex](8.85 \times 10^{-12}\times3.97 ) / 0.066 \times 10^{-3}[/tex]
Simplifying this expression, we have:
C = [tex]35.06 \times 10^{-15}\ \text{ F}[/tex]
To express the answer in exponential format, we convert the final value to the standard form:
C ≈[tex]1.85\times10^{-12}\ \text{F}[/tex]
Learn more about capacitance here:
https://brainly.com/question/31871398
#SPJ11
An elevator is hoisted by its cables at constant speed. Is the total work done on the elevator positive, negative, or zero? Explain your reasoning.
The force applied by the cables to lift the elevator is equal to the weight of the elevator, which is mg. Since the elevator is moving at a constant speed, the net force acting on the elevator is zero.
When an elevator is hoisted by its cables at a constant speed, the total work done on the elevator is zero.
The work done on an object is defined as the product of the force applied on it and the displacement caused by that force.
Work done can be positive or negative depending on the direction of the force and the displacement caused by it.
In this case, the elevator is hoisted by its cables at a constant speed. Since the speed is constant, the net force acting on the elevator is zero. This means that no work is being done on the elevator by the cables, and hence the total work done on the elevator is zero.
Let's take an example to understand this better. Suppose an elevator of mass m is being hoisted by its cables with a constant speed v.
The force applied by the cables to lift the elevator is equal to the weight of the elevator, which is mg.
Since the elevator is moving at a constant speed, the net force acting on the elevator is zero.
Therefore, the work done on the elevator by the cables is zero.
In conclusion, when an elevator is hoisted by its cables at a constant speed, the total work done on the elevator is zero.
Learn more about force here:
https://brainly.com/question/30507236
#SPJ11
An LC circuit is comprised of a capacitor with 10.0 mF and initial charge of 1.5 C, and inductor with L = 6.2 H.
a) What is the angular frequency of oscillation?
b) Assuming a phase of 0, what is the current at t = 3.0 s?
c) Now assume the circuit has resistance 45Ω. What is the angular frequency of the oscillation of charge?
d) What is the current in this circuit after 3.0 s assuming a phase of zero? Compare this to your answer to part b).
e) If this circuit instead had an AC voltage source with a maximum voltage of 40V and a frequency of 120Hz, what would the impedance of the circuit be? What is the RMS voltage?
The angular frequency of oscillation is 5.06 rad/s. the current at t = 3.0 s is 0.71 A. The angular frequency of the oscillation of charge is 5.05 rad/s. the current in this circuit after 3.0 s assuming a phase of zero is 0.68 A. The impedance of the circuit is 45.09Ω and the RMS voltage is 28.28V.
a) The angular frequency (ω) of the LC circuit can be calculated using the formula ω = 1 / sqrt(LC). Plugging in the values,[tex]\omega = 1 / \sqrt((6.2 H)(10.0 mF)) = 5.06 rad/s[/tex].
b) To find the current (I) at t = 3.0 s with a phase of 0, we can use the equation[tex]I = (Q_0 / C) * cos(\omega t)[/tex]. Substituting the given values, [tex]I = (1.5 C / 10.0 mF) * cos(5.06 rad/s * 3.0 s) = 0.71 A[/tex].
c) Considering the circuit has a resistance of 45Ω, the angular frequency (ω') of the oscillation of charge can be determined using the formula [tex]\omega' = \sqrt((1 / LC) - (R^2 / (4L^2)))[/tex]. Substituting the given values, [tex]\pmega' = \sqrt((1 / ((10.0 mF)(6.2 H))) - ((45[/tex]Ω[tex])^2 / (4(6.2 H)^2))) = 5.05 rad/s.[/tex]
d) The current in the circuit after 3.0 s with a phase of zero can be calculated using the same equation as part b. Substituting the values, I' = (1.5 C / 10.0 mF) * cos(5.05 rad/s * 3.0 s) = 0.68 A. This can be compared to the previous answer to assess the impact of resistance.
e) If the circuit had an AC voltage source with a maximum voltage of 40V and a frequency of 120Hz, the impedance (Z) can be determined using the formula [tex]Z = \sqrt(R^2 + (\omega L - 1 / (\omega C))^2)[/tex]. Substituting the given values, [tex]Z = \sqrt((45[/tex]Ω[tex])^2[/tex] [tex]+ ((2\pi(120Hz)(6.2 H)) - 1 / (2\pi(120Hz)(10.0 mF)))^2) = 45.09[/tex]Ω. The RMS voltage can be calculated as [tex]V_{RMS} = (V_{max}) / \sqrt(2) = 40V / \sqrt(2) = 28.28V.[/tex]
Learn more about angular frequency here:
https://brainly.com/question/32670038
#SPJ11
A generator connected to an RLC circuit has an rms voltage of 150 V and an rms current of 33 mA .A generator connected to an RLC circuit has an rms voltage of 150 V and an rms current of 33 mA .
If the resistance in the circuit is 3.0 kΩ and the capacitive reactance is 6.7 kΩ , what is the inductive reactance of the circuit?
The required solution is:Inductive reactance of the circuit is 1.38 kΩ.
Given information: The rms voltage (Vrms) of the generator = 150 VThe rms current (Irms) in the circuit = 33 mAThe resistance (R) in the circuit = 3.0 kΩThe capacitive reactance (Xc) = 6.7 kΩThe formula to calculate the inductive reactance (XL) of the circuit is given as,XL = √[R² + (Xl - Xc)²]where,XL is the inductive reactanceXc is the capacitive reactance of the circuit. R is the resistance of the circuit.
Substituting the given values in the formula,XL = √[ (3.0 kΩ)² + (Xl - 6.7 kΩ)²]⇒ XL² = (3.0 kΩ)² + (XL - 6.7 kΩ)²⇒ XL² = 9.0 kΩ² + XL² - 2 * 6.7 kΩ * XL + (6.7 kΩ)²⇒ 0 = 9.0 kΩ² - 2 * 6.7 kΩ * XL + (6.7 kΩ)²⇒ 0 = (3.0 kΩ - XL) (3.0 kΩ + XL) - (6.7 kΩ)²XL = (6.7 kΩ)² / (3.0 kΩ + XL)⇒ (3.0 kΩ + XL) XL = (6.7 kΩ)²⇒ XL² + 3.0 kΩ * XL - (6.7 kΩ)² = 0Solving for XL using the quadratic formula, we get,XL = 1.38 kΩ and XL = -4.38 kΩ.
Since inductive reactance can never be negative, we ignore the negative value.So, the inductive reactance of the circuit is 1.38 kΩ (approximately).Hence, the required solution is:Inductive reactance of the circuit is 1.38 kΩ.
Learn more about Inductive reactance here,
https://brainly.com/question/32092284
#SPJ11
A loop of wire with a diameter of 20 cm is located in a uniform magnetic field. The loop is perpendicular to the field. The field has a strength of 2.0 T. If the loop is removed completely from the field in 1.75 ms, what is the average induced emf? If the loop is connected to a 150 kohm resistor what is the current in the resistor?
Answer: The current in the resistor is 0.00024 A.
The average induced emf can be determined by Faraday's law of electromagnetic induction which states that the emf induced in a loop of wire is proportional to the rate of change of the magnetic flux passing through the loop.
Mathematically: ε = -N(ΔΦ/Δt)
where,ε is the induced emf, N is the number of turns in the loop, ΔΦ is the change in the magnetic flux, Δt is the time interval.
The magnetic flux is given as,Φ = BA
where, B is the magnetic field strength, A is the area of the loop.
Since the loop has been completely removed from the field, the change in magnetic flux (ΔΦ) is given by,ΔΦ = BA final - BA initial. Where,
BA initial = πr²
B = π(0.1m)²(2.0 T)
= 0.0628 Wb.
BA final = 0 Wb (As the loop has been removed completely from the field).
Therefore,ΔΦ = BA final - BA initial
= 0 - 0.0628
= -0.0628 Wb.
Since the time interval is given as Δt = 1.75 ms
= 1.75 × 10⁻³ s, the induced emf can be calculated as,
ε = -N(ΔΦ/Δt)
= -N × (-0.0628/1.75 × 10⁻³)
= 35.94 N.
The average induced emf is 35.94 V (approx).
Now, if the loop is connected to a 150 kΩ resistor, the current in the resistor can be determined using Ohm's law, which states that the current passing through a conductor between two points is directly proportional to the voltage across the two points and inversely proportional to the resistance between them. Mathematically, it can be represented as,
I = V/R Where, I is the current flowing through the resistor V is the voltage across the resistor R is the resistance of the resistor. From the above discussion, we know that the induced emf across the loop of wire is 35.94 V, and the resistor is 150 kΩ = 150 × 10³ Ω
Therefore, I = V/R
= 35.94/150 × 10³
= 0.00024 A.
The current in the resistor is 0.00024 A.
Learn more about Ohm's law : https://brainly.com/question/14296509
#SPJ11
If the magnetic field at the center of a single loop wire with radius of 8.08cm in 0.015T, calculate the magnetic field if the radius would be 3.7cm with the same current. Express your result in units of T with 3 decimals.
Answer:
The magnetic field if the radius would be 3.7cm with the same current is 0.0069T.
Let B1 be the magnetic field at the center of a single loop wire with radius of 8.08cm and B2 be the magnetic field if the radius would be 3.7cm with the same current.
Now,
The magnetic field at the center of a single loop wire is given by;
B = (μ₀I/2)R
Where μ₀ is the magnetic constant,
I is the current and
R is the radius.
The magnetic field at the center of a single loop wire with radius of 8.08cm is given as,
B1 = (μ₀I/2)R1 …(i)
Similarly, the magnetic field at the center of a single loop wire with radius of 3.7cm is given as,
B2 = (μ₀I/2)R2 …(ii)
As given, current I is same in both the cases,
i.e., I1 = I2 = I
Also, μ₀ is a constant, hence we can write equation (i) and (ii) as, B1 ∝ R1 and B2 ∝ R2
Thus, the ratio of magnetic field for the two different radii can be written as;
B1/B2 = R1/R2
On substituting the values, we get;
B1/B2 = (8.08)/(3.7)
B2 = B1 × (R2/R1)
B2 = 0.015 × (3.7/8.08)
B2 = 0.00686061947
B2= 0.0069 (approx)
Therefore, the magnetic field if the radius would be 3.7cm with the same current is 0.0069T.
Hence, the answer is 0.0069T.
Learn more about magnetic field, here
https://brainly.com/question/7645789
#SPJ11
A proton moving perpendicular to a magnetic field of 9.80 μT follows a circular path of radius 4.95 cm. What is the proton's speed? in m/s.
(uses above question) If the magnetic field is pointed into the page and the proton is moving to the left when it enters the region of the magnetic field, the proton goes in what direction as viewed from above?
Clockwise
Counterclockwise
Down the page
Up the page
The speed of the proton is approximately 2.29 x 10^6 m/s.
Regarding the direction of motion as viewed from above, the proton will move counterclockwise in the circular path.
To calculate the proton's speed, we can use the formula for the centripetal force acting on a charged particle moving in a magnetic field:
F = qvB
where F is the centripetal force, q is the charge of the proton, v is its velocity, and B is the magnetic field strength.
In this case, the centripetal force is provided by the magnetic force, so we can equate the two:
qvB = mv²/r
where m is the mass of the proton and r is the radius of the circular path.
Solving for v, we get:
v = (qB*r) / m
The values:
q = charge of a proton = 1.6 x 10^-19 C (Coulombs)
B = magnetic field strength = 9.80 μT = 9.80 x 10^-6 T (Tesla)
r = radius of the circular path = 4.95 cm = 4.95 x 10^-2 m
m = mass of a proton = 1.67 x 10^-27 kg
Substituting the values into the formula, we can calculate the speed:
v = (1.6 x 10^-19 C * 9.80 x 10^-6 T * 4.95 x 10^-2 m) / (1.67 x 10^-27 kg) = 2.29 x 10^6 m/s.
To know more about proton
https://brainly.com/question/29248303
#SPJ11
Find the flux of the Earth's magnetic field of magnitude 5.00 ✕ 10-5 T, through a square loop of area 10.0 cm2 for the following.
(a) when the field is perpendicular to the plane of the loop
T·m2
(b) when the field makes a 60.0° angle with the normal to the plane of the loop
T·m2
(c) when the field makes a 90.0° angle with the normal to the plane
T·m2
To find the flux of the Earth's magnetic field through a square loop of area 10.0 cm^2, we need to consider the angle between the magnetic field and the normal plane of the loop.
The flux is given by the product of the magnetic field magnitude and the component of the field perpendicular to the loop, multiplied by the area of the loop.
(a) When the magnetic field is perpendicular to the plane of the loop, the flux is given by the formula Φ = B * A, where B is the magnetic field magnitude and A is the area of the loop. Substituting the given values, we can calculate the flux.
(b) When the magnetic field makes a 60.0° angle with the normal to the plane of the loop, the flux is given by the formula Φ = B * A * cos(θ), where θ is the angle between the magnetic field and the normal to the plane. By substituting the given values, we can calculate the flux.
(c) When the magnetic field makes a 90.0° angle with the normal to the plane, the flux is zero since the magnetic field is parallel to the plane and does not intersect it.
Learn more about magnetic flux here:
https://brainly.com/question/13851713
#SPJ11
An electron is accelerated from rest by a potential difference of 350 V. It than enters a uniform magnetic field of magnitude 200 mT with its velocity perpendicular to the field. Calculate (a) the speed of the electron and (b) the radius of its path in the magnetic field. * (2 Points) O 7.11 x 10^7 m/s, 3.16 x 10^-4 m 5.11 x 10^7 m/s, 6.16 x 10^-4 m 1.11 x 10^7 m/s, 3.16 x 10^-4 m O 3.11 x 10^7 m/s, 3.16 x 10^-4 m O 1.11 x 10^7 m/s, 6.16 x 10^-4 m
Substituting the values, we getr = [(9.11 × 10⁻³¹ kg)(1.11 × 10⁷ m/s)]/[(1.6 × 10⁻¹⁹ C)(200 mT)]r = 3.16 × 10⁻⁴ mTherefore, the answer is 1.11 x 10^7 m/s, 3.16 x 10^-4 m.
(a) Speed of the electronThe formula for potential energy isPE = qVWhere q is the charge and V is the potential difference. The electron is negatively charged, and its charge is 1.6 × 10⁻¹⁹ C.Therefore, PE = (1.6 × 10⁻¹⁹ C)(350 V)PE = 5.6 × 10⁻¹⁷ JThe formula for kinetic energy isKE = (1/2)mv²where m is the mass and v is the velocity of the electron. The mass of the electron is 9.11 × 10⁻³¹ kg.Using the law of conservation of energy, we can equate the kinetic energy of the electron with the potential energy it gains when accelerated by the potential difference.
Kinetic energy of the electron = Potential energy gainedKE = PEKE = 5.6 × 10⁻¹⁷ Jv² = (2KE)/mv² = (2(5.6 × 10⁻¹⁷ J))/(9.11 × 10⁻³¹ kg)v² = 1.23 × 10¹⁷v = √(1.23 × 10¹⁷)v = 1.11 × 10⁷ m/s(b) Radius of the pathThe formula for the radius of the path of a charged particle moving in a magnetic field isr = (mv)/(qB)where r is the radius, m is the mass of the charged particle, v is its velocity, q is its charge, and B is the magnetic field strength.Substituting the values, we getr = [(9.11 × 10⁻³¹ kg)(1.11 × 10⁷ m/s)]/[(1.6 × 10⁻¹⁹ C)(200 mT)]r = 3.16 × 10⁻⁴ mTherefore, the answer is 1.11 x 10^7 m/s, 3.16 x 10^-4 m.
Learn more about Velocity here,
https://brainly.com/question/80295
#SPJ11
1. We saw how hydrostatic equilibrium can be used to determine the conditions in the interior of the Sun, but it can also be applied to the Earth's ocean. The major difference is that water, to a good approximation, is incompressible-you can take its density to be constant. Furthermore, we can take the acceleration of gravity to be constant, since the depth of the ocean is thin compared to the radius of the Earth.
Using this approximation, find the pressure in the ocean 1 km beneath the surface.
Side note: the reason that we can assume that water is incompressible is that it does not obey the ideal gas law, but rather a different relation where pressure is proportional to density to a high power.
Hydrostatic equilibrium
can be used to determine the conditions in the interior of the sun, and it can also be applied to the Earth's ocean.
The major difference between the two is that water, to a good approximation, is incompressible; you can take its
density
to be constant. We can also take the acceleration of gravity to be constant because the depth of the ocean is thin compared to the radius of the Earth.The reason we can assume that water is incompressible is that it does not obey the ideal gas law but rather a different relation in which
pressure
is proportional to density to a high power. The pressure in the ocean 1 km beneath the surface can be calculated using hydrostatic equilibrium.Pressure is proportional to density and depth. Since the density of water is almost constant, we can use the expression pressure = ρgh to calculate the pressure at any depth h in the ocean, where ρ is the density of water and g is the acceleration due to gravity. Using this equation, we can calculate the pressure 1 km beneath the
surface
of the ocean.ρ = 1,000 kg/m³, g = 9.8 m/s², and h = 1,000 mUsing the expression pressure = ρgh, we get the following:Pressure = 1,000 x 9.8 x 1,000 = 9,800,000 PaThus, the pressure 1 km beneath the surface of the ocean is 9.8 MPa.
Learn more about
pressure
https://brainly.com/question/21611721
#SPJ11
Calculating this, we find that the pressure in the ocean 1 km beneath the surface is approximately 9,800,000 Pascals (Pa).
To find the pressure in the ocean 1 km beneath the surface, we can use the concept of hydrostatic equilibrium. In this case, we assume that water is incompressible, meaning its density remains constant. Additionally, we can consider the acceleration due to gravity as constant, since the depth of the ocean is much smaller compared to the radius of the Earth.
In hydrostatic equilibrium, the pressure at a certain depth is given by the equation P = P0 + ρgh, where P is the pressure, P0 is the pressure at the surface, ρ is the density of the fluid (water), g is the acceleration due to gravity, and h is the depth.
Since the density of water is constant, we can ignore it in our calculations. Given that the depth is 1 km (1000 m) and assuming the acceleration due to gravity as [tex]9.8 m/s^2[/tex], we can plug these values into the equation to find the pressure:
P = P0 + ρgh
P = P0 + (density of water) * (acceleration due to gravity) * (depth)
P = P0 + (1000 kg/m^3) * ([tex]9.8 m/s^2[/tex]) * (1000 m)
Learn more about pressure
https://brainly.com/question/30673967
#SPJ11
f B⇀ represents a magnetic field and A represents the total area of the surface, what does the equation B→·A→=0 describe?
A magnetic field that is everywhere parallel to the surface.
A magnetic field that is uniform in magnitude and everywhere horizontal.
The equation is false because it describes a magnetic monopole, which does not exist.
The equation describes any magnetic field that can exist in nature.
The equation B→·A→=0 accurately describes a magnetic field that is everywhere parallel to the surface, indicating that the magnetic field lines are not intersecting or penetrating the surface but are instead running parallel to it.
The equation B→·A→=0 describes a magnetic field that is everywhere parallel to the surface. Here, B→ represents the magnetic field vector, and A→ represents the vector normal to the surface with a magnitude equal to the total area of the surface A. When the dot product B→·A→ equals zero, it means that the magnetic field vector B→ is perpendicular to the surface vector A→. In other words, the magnetic field lines are parallel to the surface.This scenario suggests that the magnetic field is not penetrating or intersecting the surface, but rather running parallel to it. This can occur, for example, when a magnetic field is generated by a long straight wire placed parallel to a surface. In such a case, the magnetic field lines would be perpendicular to the surface.
Learn more about magnetic field here:
https://brainly.com/question/30331791
#SPJ11
What is the total energy of an electron moving with a speed of 0.74c, (in keV )?
The total energy of an electron moving at a speed of 0.74c is approximately 250 keV. The total energy of a moving electron can be determined using the relativistic energy equation.
The relativistic energy equation states that the total energy (E) of an object moving with a relativistic speed can be calculated using the equation:
[tex]E = (\gamma - 1)mc^2[/tex]
where γ (gamma) is the Lorentz factor given by:
[tex]\gamma = 1/\sqrt(1 - v^2/c^2)[/tex]
In this case, the electron is moving with a speed of 0.74c, where c is the speed of light in a vacuum. Calculate γ by substituting the given velocity into the Lorentz factor equation:
[tex]\gamma = 1/\sqrt(1 - (0.74c)^2/c^2)[/tex]
Simplifying this equation,
[tex]\gamma = 1/\sqrt(1 - 0.74^2) = 1/\sqrt(1 - 0.5484) = 1/\sqrt(0.4516) = 1/0.6715 \approx 1.49[/tex]
Next, calculate the rest mass energy ([tex]mc^2[/tex]) of the electron, where m is the mass of the electron and [tex]c^2[/tex] is the speed of light squared. The rest mass energy of an electron is approximately 0.511 MeV (mega-electron volts) or 511 keV.
Finally, calculate the total energy of the electron:
E = (1.49 - 1)(511 keV) = 0.49(511 keV) ≈ 250 keV
Therefore, the total energy of an electron moving with a speed of 0.74c is approximately 250 keV.
Learn more about total energy here:
https://brainly.com/question/14062237
#SPJ11
Find the range in wavelengths (in vacuum) for visible light in the frequency range between 7.9 × 10¹⁴ Hz (violet light) Express the answers in nanometers. (Express your answer in whole number)
The range in wavelengths (in vacuum) for visible light in the frequency range between 7.9 × 10¹⁴ Hz (violet light) is 380 nm (approx).
The formula is given as:
frequency = (speed of light) / (wavelength)
Where:
frequency = 7.9 x 10¹⁴ Hz
speed of light = 3 x 10⁸ m/s (in vacuum)
Solving for wavelength:
wavelength = (speed of light) / (frequency)
Therefore, wavelength = (3 x 10⁸) / (7.9 x 10¹⁴) = 3.80 x 10⁻⁷ m or 380 nm (approx)
Hence, the range in wavelengths (in vacuum) for visible light in the frequency range between 7.9 × 10¹⁴ Hz (violet light) is 380 nm (approx).
Learn more about frequency: https://brainly.com/question/254161
#SPJ11
A radionsonde was launched at an elevation 200 m with observed surface air temperature 20∘ Cnd surface pressure 1002mb. The radiosonde data show that temperatures are 18∘ C at 980mb,15∘ C at 950mb, etc. Calculate geopotential heights at 980mb and 950mb
Answer:A radiosonde is a battery-powered telemetry instrument carried into the atmosphere usually by a weather balloon that measures various atmospheric parameters and transmits them by radio to a ground receiver. Modern radiosondes measure or calculate the following variables: altitude, pressure, temperature, relative humidity, wind (both wind speed and wind direction), cosmic ray readings at high altitude and geographical position (latitude/longitude). Radiosondes measuring ozone concentration are known as ozonesondes.[1]
sorry if this is to much
Explanation:
Alkaline batteries have the advantage of putting out constant voltage until very nearly the end of their life. How long will an alkaline battery rated at 1.04 A⋅h and 1.4 V keep a 0.92 W flashlight bulb burning? _____________ hours
The alkaline battery rated at 1.04 A⋅h and 1.4 V will keep the 0.92 W flashlight bulb burning for about 0.996 hours.
Alkaline battery rated at 1.04 A⋅h and 1.4 V
Power required for flashlight bulb to burn = 0.92 W
Power is given by P = VI, where P is the power, V is the voltage, and I is the current.
Rearranging the above equation, we get I = P/V.
The current required for the flashlight bulb to burn is:
I = 0.92/1.4 = 0.657 A
The total charge in the battery is Q = It.
Charge is given in the unit of Coulombs (C).
1 A flows when 1 C of charge passes a point in 1 second.
Hence, 1 A flows when 3600 C of charge passes a point in 1 hour.
Therefore, 1 Coulomb = 1 A × 1 s
1 Ah = 1 A × 3600 s
So, 1 A⋅h = 3600 C
Charge in the battery Q = It = 0.657 A × (1.04 A ⋅ h) × (3600 s/h) = 2.36 × 10⁶ C
The time for which the battery will last is t = Q/I = (2.36 × 10⁶ C)/(0.657 A) = 3.59 × 10³ s
The time in hours is 3.59 × 10³ s/(3600 s/h) = 0.996 h
Therefore, the alkaline battery rated at 1.04 A⋅h and 1.4 V will keep the 0.92 W flashlight bulb burning for about 0.996 hours.
Learn more about battery: https://brainly.com/question/26466203
#SPJ11
you to analyse a single phase inverter utilizing thyristors that supply an RL load (R=1092 and L-25mH). Given that the supply voltage is from 12 Vpc PV solar systems which is then boosted to 125 Vpc and finally inverted to give the output of 110 Vrms, 60 Hz. Find: (i) the thyristors firing angle (ii) the inverter Total Harmonic Distortion (THD) (iii) a new firing angle for the thyristors to reduce the inverter THD (iv) the new THD of the inverter (10 marks) Assume: the inverter only carry odd number harmonics, and only harmonic up to n=11 are deemed significant.
The thyristors firing angle is 0°. The inverter Total Harmonic Distortion (THD) is 0%. Since the THD is already 0%, there is no need to adjust the firing angle. The new THD of the inverter remains 0%.
Supply voltage: 12 Vdc from PV solar systems
Boosted voltage: 125 Vdc
Inverted output voltage: 110 Vrms, 60 Hz
Load: RL load, where R = 1092 Ω and L = 25 mH
(i) Thyristors firing angle:
The firing angle of the thyristors in a single-phase inverter can be determined using the formula:
α = cos^(-1)((R/L)(Vdc/Vm))
Substituting the given values:
α = cos^(-1)((1092/25 × 10^(-3))(125/110))
= cos^(-1)(4.88)
≈ 0°
Note: The calculated firing angle of 0° indicates that the thyristors are triggered at the beginning of each half-cycle.
(ii) Inverter Total Harmonic Distortion (THD):
The THD of the inverter can be calculated using the formula:
THD = √[(V2^2 + V3^2 + V5^2 + ...)/(V1^2)]
Since the question assumes that the inverter carries only odd-numbered harmonics up to n = 11, we can calculate the THD considering the significant harmonics.
THD = √[(V2^2 + V3^2 + V5^2 + ...)/(V1^2)]
= √[(0^2 + 0^2 + 0^2 + ...)/(110^2)]
= 0
Note: The calculated THD of 0% indicates that there are no significant harmonics present in the inverter output.
(iii) New firing angle to reduce the inverter THD:
Since the THD was already 0% in the previous calculation, there is no need to adjust the firing angle to further reduce the THD.
(iv) New THD of the inverter:
As mentioned in the previous calculation, the THD is already 0% in this case, so there is no change in the THD.
Learn more about Total Harmonic Distortion at: https://brainly.com/question/30198365
#SPJ11
To push a 28.0 kg crate up a frictionless incline, angled at 25.0° to the horizontal, a worker exerts a force of 219 N parallel to the incline. As the crate slides 1.5 m, how much work is done on the crate by (a) the worker's applied force. (b) the gravitational force or the crate, and (c) the normal force exerted by the incline on the crate? (d) What is the total work done on the crate? (a) Number ______________ Units ________________
(b) Number ______________ Units ________________
(c) Number ______________ Units ________________
(d) Number ______________ Units ________________
To push a 28.0 kg crate up a frictionless incline, angled at 25.0° to the horizontal, a worker exerts a force of 219 N parallel to the incline.
Mass, m = 28.0 kg, angle of inclination, θ = 25.0°, distance travelled, d = 1.5 m, applied force, F = 219 N.
Work is defined as the product of the applied force and the displacement of the object. It is represented by W.
So, the work done by the worker is calculated as follows
:W = Fdcos∅
W = 219*1.5cos 25.0°
W = 454.8J
So, the work done by the worker is 454.8 J.
The gravitational force acting on the crate can be calculated as follows:
mg = 28.0*9.8 = 274.4N
Now, the work done by the gravitational force can be calculated as follows:
W = mgh
W = 28.0*9.8*1.5sin 25.0°
W = 362.3J
So, the work done by the gravitational force is 362.3 J.
The normal force is equal and opposite to the component of the gravitational force acting perpendicular to the incline, that is,
N = mgcos∅
Now, the work done by the normal force can be calculated as follows:
W = Ndcos (90.0° - ∅ )
W = mgcos∅*dsin∅
W = 28.0*9.8*1.5*sin 25.0°*cos 65.0°
W = 98.1J
So, the work done by the normal force is 98.1 J.
The total work done on the crate is the sum of the work done by the worker, gravitational force and normal force.
W_total = W_worker + W_gravity + W_normaW_total = 454.8+ 362.3+ 98.1
W_total= 915.2
Hence, the total work done on the crate is 915.2 J.
a) The work done by the worker is 454.8 J.
(b) The work done by the gravitational force is 362.3 J.
(c) The work done by the normal force is 98.1 J.
(d) The total work done on the crate is 915.2 J.
Learn more on how incline affects force applied: https://brainly.com/question/11544063
#SPJ11
Solve numerically for the thermal efficiency, η, assuming that T h
=910 ∘
C and T c
=580 ∘
C. Numeric : A numeric value is expected and not an expression. η= =1− 1183.15K
331.15K
=.72011=7 Problem 5: Suppose you want to operate an ideal refrigerator that has a cold temperature of −10.5 ∘
C, and you would like it to have a coefficient of performance of 5.5. What is the temperature, in degrees Celsius, of the hot reservoir for such a refrigerator? Numeric : A numeric value is expected and not an expression. T h
=
Therefore, the numeric value is 339.1.
Given, the hot and cold temperatures of the refrigerator, respectively are Th = 910 °C and Tc = 580 °C. We are supposed to solve numerically for the thermal efficiency η.
Formula to calculate the efficiency of the heat engine is given by:η=1- (Tc/Th)η = 1 - (580 + 273.15) / (910 + 273.15)η = 0.72011Hence, the thermal efficiency η is 0.72011. The numeric value is given as 0.72011. Therefore, the numeric value is 0.72011.
Now, let's solve the second problem.Problem 5:Suppose you want to operate an ideal refrigerator that has a cold temperature of -10.5°C, and you would like it to have a coefficient of performance of 5.5. What is the temperature, in degrees Celsius,
of the hot reservoir for such a refrigerator?
The formula to calculate the coefficient of performance of a refrigerator is given by:K = Tc / (Th - Tc)The desired coefficient of performance of the refrigerator is given as 5.5. We are supposed to calculate the hot temperature, i.e., Th.
Thus, we can rearrange the above formula and calculate Th as follows:Th = Tc / (K - 1) + TcTh = (-10.5 + 273.15) / (5.5 - 1) + (-10.5 + 273.15)Th = 325.85 / 4.5 + 262.65 = 339.1 °CHence, the temperature of the hot reservoir for such a refrigerator is 339.1 °C.
The numeric value is given as 339.1.
to know more about thermal efficiency
https://brainly.com/question/13982702
#SPJ11
A baseball bat traveling rightward strikes a ball when both are moving at 30.1 m/s (relative to the ground) toward each other. The bat and ball are in contact for 1.10 ms, after which the ball travels rightward at a speed of 42.5 m/s relative to the ground. The mass of the bat and the ball are 850 g and 145 g, respectively. Define rightward as the positive direction.
Calculate the impulse given to the ball by the bat
Calculate the impulse given to the bat by the ball.
What average force ⃗ avg does the bat exert on the ball?
The impulse given to the ball by the bat is equal to the change in momentum of the ball during their interaction. The impulse can be calculated by subtracting the initial momentum of the ball from its final momentum.
The initial momentum of the ball is given by the product of its mass (m_ball) and initial velocity (v_initial_ball): p_initial_ball = m_ball * v_initial_ball. The final momentum of the ball is given by: p_final_ball = m_ball * v_final_ball.
To calculate the impulse, we can use the equation: Impulse = p_final_ball - p_initial_ball. Substituting the values, we have Impulse = (m_ball * v_final_ball) - (m_ball * v_initial_ball).
Similarly, we can calculate the impulse given to the bat by the ball using the same principle of conservation of momentum. The impulse given to the bat can be obtained by subtracting the initial momentum of the bat from its final momentum.
The average force (F_avg) exerted by the bat on the ball can be calculated using the equation: F_avg = Impulse / Δt, where Δt is the time of contact between the bat and the ball.
Learn more about momentum here;
https://brainly.com/question/18798405
#SPJ11
Tell us on what basis we select following for
measuring flow rates
a) Pitot Tube
b) Orifice meter
c) Venturi meter
d) Rotameter
The selection of the following devices for measuring flow rates are based on the following factors: a) Pitot Tube: The Pitot tube is a device used to measure the flow velocity of fluids. It is used to measure the velocity of air or other gases flowing in a pipe.
The selection of a pitot tube is based on the following factors: Pipe size Accuracy of measurement Required flow range Fluid properties b) Orifice meter: An orifice meter is a device used to measure the flow rate of a fluid. The selection of an orifice meter is based on the following factors: Pipe size Accuracy of measurement Fluid properties Cost. c) Venturi meter: A Venturi meter is a device used to measure the flow rate of a fluid. The selection of a Venturi meter is based on the following factors: Pipe size Accuracy of measurement Fluid properties Cost. d) Rotameter: A rotameter is a device used to measure the flow rate of a fluid. The selection of a rotameter is based on the following factors: Pipe size. Accuracy of measurement Fluid properties Cost.
To know more about pressure visit:
https://brainly.com/question/31555867
#SPJ11
Two metal plates with only air between them are separated by 148 cm One of the plates is at a potential of 327 volts and the other plate is at a potential of 341 volts. What is the magnitude of the electric field between the plates in volts/meter? (Enter answer as a positive integer Do not include unit in answer
The magnitude of the electric field between the plates is approximately 9 V/m.
To calculate the magnitude of the electric field between the plates, we can use the formula:
Electric field (E) = Potential difference (V) / Distance (d).
Given that the potential difference between the plates is 341 V - 327 V = 14 V, and the distance between the plates is 148 cm = 1.48 m, we can substitute these values into the formula:
E = 14 V / 1.48 m.
Calculating the value, we find:
E ≈ 9.459 V/m.
Therefore, the magnitude of the electric field between the plates is approximately 9 V/m.
Learn more about magnitude here:
https://brainly.com/question/30033702
#SPJ11