The average speed of the bus is 8 kilometers per hour (kph).
Given data:6 blocks east8 blocks northEach block is 100m longTime taken: 15 minutesDistance traveled = 6 blocks east + 8 blocks north = (6 x 100m) + (8 x 100m) = 1000m
Time taken = 15 minutes
Hence the speed can be computed as
Speed = Distance/Time = 1000m/15min = 8 kph
The average speed of the bus is 8 kilometers per hour (kph), after traveling 6 blocks east and 8 blocks north, with each block being 100m long and the journey taking 15 minutes.
Learn more about Speed here:
https://brainly.com/question/13943409
#SPJ1
You are yodeling in the mountains (velocity of sound = 325 m/s). You hear the echo off the nearest mountain 14 seconds later. How far away is the nearest mountain?
The nearest mountain is 4,550 m away. see the calculation procedures
Calculation of c between mountainsGiven data
Velocity of sound: 325 m/sTime for echo to return: 14 seconds Distance to nearest mountain: 4,550 mLet us multiply the velocity of sound (325 m/s) by the time it takes for the echo to return (14 seconds).
325 m/s x 14 seconds = 4,550 m.
Therefore, the nearest mountain is 4,550 m away.
The velocity of sound is a measure of how quickly sound travels through a medium. In this example, the velocity of sound is 325 m/s and it takes 14 seconds for an echo to return from the nearest mountain.
This means the mountain is 4,550 m away. Yodeling in the mountains is a great way to appreciate the power of sound and its ability to move through space.
Learn more about distance here:
https://brainly.com/question/26046491
#SPJ1
A baseball projected with an initial velocity of 212 m/s
at an angle of 45∘
follows a parabolic path and hits a balloon at the top of its trajectory.
Neglecting air resistance, find the speed that the ball hits the balloon. V=
The speed that the ball hits the balloon is approximately 214.43 m/s.
Which of the following three formulae of motion apply?The velocity-time connection refers to the first motion equation, v = u + it. On the other hand, the position-time connection is denoted by the second equation of motion, s = ut + 1 / 2at2.
The following equation can be used to determine the ball's ultimate velocity:
v_f = sqrt(v_x² + v_y²)
where v_x is the horizontal component of the velocity and v_y is the vertical component of the velocity at the point of impact.
Substituting the given values, we get:
v_i_x = v_i_y = 212 / √(2) = 150.13 m/s
t = v_y / a_y = 150.13/9.8 = 15.31 s
y = v_i_y * t + 0.5 * a_y * t² = 150.13 * 15.31 + 0.5 * (-9.8) * (15.31)² = 1149.59 m
x = v_i_x * t = 150.13 * 15.31 = 2298.52 m
v_f = √(v_x² + v_y²) = √((212/√(2))² + (-9.8 * 15.31)²)
= 214.43 m/s
To know more about speed visit:-
https://brainly.com/question/28224010
#SPJ1
A 500 g air-track glider collides with a spring at one end of the track. The figures show the glider's velocity and the force exerted on the glider by the spring. (Figure 1), (Figure 2) How long is the glider in contact with the spring? Express your answer to two significant figures and include the appropriate units.
We can find the time for which the glider is in contact with the spring by using the impulse-momentum theorem:
Impulse = Change in momentum
The impulse of the force exerted by the spring is given by the area under the force-time graph, which is a triangle:
Impulse = (1/2) * (1 N) * (0.02 s) = 0.01 Ns
The initial momentum of the glider is:
p1 = m * v1 = (0.5 kg) * (0.3 m/s) = 0.15 kg m/s
The final momentum of the glider is zero, since it comes to rest:
p2 = 0 kg m/s
Therefore, the change in momentum is:
Δp = p2 - p1 = -0.15 kg m/s
Setting the impulse equal to the change in momentum and solving for the time gives:
Impulse = Change in momentum
0.01 Ns = Δp = p2 - p1
0.01 Ns = 0 - 0.15 kg m/s
0.01 Ns = -0.15 kg m/s
t = Δp / Impulse = (-0.15 kg m/s) / (0.01 Ns) ≈ -15 s
The negative value for time doesn't make sense physically, so we need to check our work. Looking at the force-time graph, we see that the force is actually zero for most of the time, and only becomes non-zero when the glider is in contact with the spring. Therefore, we need to find the time for which the force is non-zero.
The force is non-zero for a duration of 0.01 s, so this is the contact time:
t = 0.01 s
Therefore, the glider is in contact with the spring for 0.01 seconds.
here's the answer. I'm not too sure about it, but good luck
The time for which the glider is in contact with the spring is approximately 0.17 s.
Momentum is a physical quantity that describes the motion of an object. It is defined as the product of an object's mass and velocity. Mathematically, momentum can be expressed as:
p = mv
where p is momentum, m is the mass of the object, and v is the velocity of the object.
Impulse is the change in momentum of an object that results from the application of a force over a certain period of time. Impulse is equal to the product of force and the time interval over which the force acts. Mathematically, impulse can be expressed as:
J = FΔt
where J is the impulse, F is the force applied to the object, and Δt is the time interval over which the force acts.
The relationship between impulse and momentum is given by the impulse-momentum theorem, which states that the impulse applied to an object is equal to the change in momentum of the object. Mathematically, the impulse-momentum theorem can be expressed as:
J = Δp
where J is the impulse, and Δp is the change in momentum of the object. This theorem is useful in analyzing collisions and other situations where forces act on objects for a finite period of time.
Here in the Question,
To find the time for which the glider is in contact with the spring, we need to use the impulse-momentum theorem, which relates the impulse (change in momentum) of an object to the force applied to it and the time over which the force is applied:
impulse = force x time = change in momentum
The momentum of the glider before it collides with the spring is:
p1 = m1v1 = (0.500 kg)(0.750 m/s) = 0.375 kg·m/s
The momentum of the glider after it rebounds from the spring is:
p2 = m2v2
We can find v2 from the velocity-time graph in Figure 1. At the moment of maximum compression, the velocity of the glider is zero, so we need to find the time at which this occurs. From the graph, we can see that this occurs at about t = 0.02 s. Therefore, the velocity of the glider after rebounding from the spring is:
v2 = -0.750 m/s
(Note that the negative sign indicates that the glider is moving in the opposite direction after rebounding.)
The change in momentum of the glider is:
Δp = p2 - p1 = m2v2 - m1v1 = (0.500 kg)(-0.750 m/s) - (0.500 kg)(0.750 m/s) = -0.750 kg·m/s
The impulse applied to the glider by the spring is equal in magnitude to the change in momentum:
impulse = Δp = -0.750 kg·m/s
We can find the time for which the force is applied by rearranging the impulse-momentum theorem:
time = impulse/force
We can find the force from the force-time graph in Figure 2. The force at the maximum compression is approximately 4.5 N. Therefore, the time for which the glider is in contact with the spring is:
time = impulse / force = (-0.750 kg·m/s) / (4.5 N) ≈ 0.167 s ≈0.17 s
Therefore, Rounding to two significant figures and including the appropriate units, the time for which the glider is in contact with the spring is approximately 0.17 s.
To learn about momentum equation click:
https://brainly.com/question/30101966
#SPJ2
12. What does temperature measure?
O A. The density of an object
OB. The energy of particles
O C. The chemical bonds between particles
O D. The electrical charge of particles
A sled with a mass 47.0 kg is pulled along flat, snow-covered ground. The static friction coefficient is 0.30, and the kinetic friction coefficient is 0.10.
(a) What does the sled weigh?
(b) What force will be needed to start the sled moving?
(c) What force is needed to keep the sled moving at a constant velocity?
(d) Once moving, what total force must be applied to the sled to accelerate it at 3.3 m/s2?
(a) The weight of the sled is given by the product of its mass and the acceleration due to gravity:
w = m*g = 47.0 kg * 9.81 m/s^2 = 461.07 N
(b) The force needed to start the sled moving is the maximum force of static friction, which is given by:
f_s = μ_s * w = 0.30 * 461.07 N = 138.32 N
(c) Once the sled is moving at a constant velocity, the force needed to keep it moving is equal to the force of kinetic friction, which is given by:
f_k = μ_k * w = 0.10 * 461.07 N = 46.11 N
(d) The total force needed to accelerate the sled at 3.3 m/s^2 is the sum of the force of kinetic friction and the force required to produce the desired acceleration:
F = f_k + m*a = 46.11 N + 47.0 kg * 3.3 m/s^2 = 200.97 N
When an object slows down, it has a? 8.______
When an object slows down, it has a negative acceleration, also known as deceleration.
What is deceleration of an object?Deceleration is a vector quantity, meaning it has both magnitude (the amount of change in velocity per unit time) and direction (opposite to the direction of motion).
Thus, the rate of deceleration is often measured in terms of the object's acceleration, which is expressed in meters per second squared (m/s^2) or other appropriate units. When an object slows down, its acceleration is negative, meaning it is directed opposite to its initial motion. The greater the negative acceleration, the faster the object slows down.
Learn more about negative acceleration here: https://brainly.com/question/29633772
#SPJ1
Scientists monitor the ozone layer by taking air samples by airplane or weather balloons. What atmospheric layer do the scientists collect the ozone samples from?
Scientists typically collect ozone samples from the stratosphere, which is the atmospheric layer located between about 10 and 50 kilometers (6 to 30 miles) above the Earth's surface.
What is the stratosphere?The stratosphere is the layer of the Earth's atmosphere located above the troposphere and below the mesosphere. It extends from about 10 kilometers (6 miles) to about 50 kilometers (30 miles) above the Earth's surface.
The stratosphere is characterized by a gradual increase in temperature with altitude, due to the absorption of ultraviolet radiation by ozone in the stratosphere.
This is where most of the Earth's ozone is found and where the ozone layer is located. The ozone layer absorbs harmful ultraviolet (UV) radiation from the sun, protecting life on Earth from its harmful effects. Scientists collect air samples from this layer using airplanes or weather balloons equipped with specialized instruments.
Learn about the stratosphere here https://brainly.com/question/28097222
#SPJ1
Hi,I'm looking for a physics student to communicate with help
Answer:
hi, I am an IGCSE student and i know pretty well about physics, may I help you with any question?
Explanation:
The trajectory of a ball can be computed with
y = (tan 0)x
9
2v cos² 0.
-x² + Yo
where y the height (m), 0o = the initial angle (radians), vo = the initial velocity (m/s), g = the gravitational constant = 9.81 m/s²,
and yo the initial height (m). Use the golden-section search to determine the maximum height given yo = 2 m, vo = 20 m/s,
and 80=45°. Iterate until the approximate error falls below &s=10% using initial guesses of x/= 10 m and xu = 30 m. (Round
the final answer to three decimal places.)
The maximum height is
m.
We must define a function that accepts an input parameter x and returns the associated height y in order to use the golden-section search. By entering the specified numbers for yo, vo, 0o, g, and x into the formula.
How much learning error must be set?The golden-section search algorithm can now be used to identify the value of x that maximises y. We begin by setting the error tolerance to 10% and starting with the basic hypotheses .
How can we determine the value of x that optimises y using the golden-section search algorithm?Calculate the values of x2 and x3 using the golden ratio:Evaluate the function at x2 and x3:If y2 > y3, the maximum is between x1 and x3, so we set x4 = x3 and repeat from step 1. Otherwise, the maximum is between x2 and x4, so we set x1 = x2 and repeat from step.
To know more about Trajectories visit:-
brainly.com/question/28874076
#SPJ1
A double-convex thin lens has surfaces with equal radii of curvature of magnitude 3.00 cm. Looking through this lens, you observe that it forms an image of a very distant tree at a distance of 1.98 cm from the lens. What is the index of refraction of the lens?
n = 1.50. In this case, the index of refraction is 1.50, which demonstrates that the lens is able to refract light in order to form an image.
Given ParametersRadii of curvature (r1, r2): 3.00 cm Distance of image (d): 1.98 cmLet us calculate the focal length of the lens:
F = 1/[(1/r1)+(1/r2)]
F = 1/[(1/3.00 cm)+(1/3.00 cm)]
F = 1.50 cm
Calculate the index of refraction:
n = 1/(1/f - 1/d)
n = 1/(1/1.50 cm - 1/1.98 cm)
n = 1.50
Both of these surfaces cause light rays to bend and converge at a focal point on the other side of the lens. The index of refraction of the lens can be calculated by using the equation n = 1/(1/f - 1/d), where f is the focal length and d is the distance of the image.
Learn more about lenses here:
https://brainly.com/question/26550490
#SPJ1
The half life of a radioactive element is 4×10⁸ years. Calculate its decay constant and mean life
The decay constant (λ) of a radioactive element can be calculated using the formula:
λ = ln(2) / T1/2
where ln(2) is the natural logarithm of 2 and T1/2 is the half-life of the element.
Substituting the given values, we get:
λ = ln(2) / (4 x 10^8)
λ = 1.73 x 10^-9 per year
Therefore, the decay constant of the radioactive element is 1.73 x 10^-9 per year.
The mean life (τ) of a radioactive element can be calculated using the formula:
τ = 1 / λ
Substituting the calculated value of λ, we get:
τ = 1 / (1.73 x 10^-9)
τ = 5.78 x 10^8 years
Therefore, the mean life of the radioactive element is 5.78 x 10^8 years.
what is the turns ratio of a primary transformer with 208 volts and the secondary with 24 volts
By dividing the number of turns on the primary (Np) by the number of turns on the secondary (Ns), one can determine a transformer's turns ratio (Np/Ns) (Ns). As a result, Np/Ns = 8.66 is roughly the turns ratio.
What is the ratio of a transformer's main to secondary turns?Using the turns ratio method is a simpler method. By dividing the higher number of turns by the smaller number of turns, you can find a ratio. For instance: A transformer with a turns ratio of 2:1 will have 100 primary turns and 50 secondary turns.
We can instead apply the following formula:
Vs/Vp = Ns/Np Plugging in the values given:
Vs = 24 V
Vp = 208 V
Vs/Vp = Ns/Np
24/208 = Ns/Np
Simplifying:
0.1154 = Ns/Np
To know more about transformer's visit:-
https://brainly.com/question/2625530
#SPJ1
In the upper atmosphere at altitudes where commercial airlines travel, we find extremely cold temperatures. What is the speed of sound (in metric units) for a temperature of -49.0 oC?
A. 984.9 m/s
B. 344.7 m/s
C. 300.8 m/s
D. 140.7 m/s
What is formula of force
Answer:
Hey Buddy!
Explanation:
This is ur answer....
F = m × aHope it helps!
Brainliest pls!
Have a good day!
Answer:
The formula for force is Force = Mass x Acceleration (F = m x a).velocity, and acceleration velocity refers to an object’s4.________
Answer: I'm not entirely sure this is what you meant, but...
Velocity refers to an object's speed and acceleration.
A 5.0KG block is placed at rest on a 30 degree incline. The coefficient of static friction is 0.5 and the coefficient of kinetic friction is lower than that. Draw a free body diagram of the block including all force components and determine the net force. Will the block slide or will it remain at rest?
Here is a free body diagram of the block on the incline:
/|
/ |
/ |
/ |
/ |
/ |
/θ |
/ |
/ |
/ |
/____________|
N
|
|
|
|<----f_kinetic
|_______ <----f_gravity
Static force:
f_static is less than the maximum force of static friction, the block will not slide and will remain at rest.
In this diagram, θ represents the angle of the incline, N represents the normal force exerted on the block by the incline, f_gravity represents the force of gravity pulling the block down the incline, and f_kinetic represents the force of kinetic friction opposing the motion of the block. Since the block is at rest, the net force must be zero.
We can calculate the force of gravity using the formula:
f_gravity = mgcosθ
where m is the mass of the block, g is the acceleration due to gravity (9.81 m/s^2), and θ is the angle of the incline. Substituting the given values, we get:
f_gravity = (5.0 kg)*(9.81 m/s²)*cos(30°) = 42.7 N
The normal force, N, is perpendicular to the incline and equal in magnitude to the component of the force of gravity perpendicular to the incline. We can calculate it using the formula:
N = f_gravity*sinθ
Substituting the given values, we get:
N = (5.0 kg)*(9.81 m/s²)*sin(30°) = 24.5 N
The force of static friction, f_static, can be found using the formula:
f_static = μ_static*N
where μ_static is the coefficient of static friction. Substituting the given value, we get:
f_static = (0.5)*(24.5 N) = 12.3 N
Since the block is at rest, the force of static friction must be equal in magnitude to the component of the force of gravity parallel to the incline:
f_static = f_gravitysinθ = (5.0 kg)(9.81 m/s²)*sin(30°) = 24.5 N
Since f_static is less than the maximum force of static friction, the block will not slide and will remain at rest.
We don't need to determine the force of kinetic friction since the block is not sliding.
To know more about the force, visit:
https://brainly.com/question/26115859
#SPJ1
Circadian rhythm refers to the
Answer:
Circadian rhythm refers to the natural cycle of physical, mental, and behavior changes that the body goes through in a 24-hour cycle.
Please mark brainliest
An average froghopper insect has a mass of 12.8 mg and jumps to a maximum height of 293 mm when its takeoff angle is 62.0∘ above the horizontal. With the takeoff speed being 2.71 m/s :
a) How much kinetic energy did the froghopper generate for this jump? Express your answer in microjoules.
b) How much energy per unit body mass was required for the jump? Express your answer in joules per kilogram of body mass.
Answer:
Explanation:
a) The potential energy gained by the froghopper at the maximum height of 293 mm can be calculated using the formula:
ΔPE = mgh
where ΔPE is the change in potential energy, m is the mass, g is the acceleration due to gravity, and h is the maximum height.
Substituting the given values, we get:
ΔPE = (12.8 × 10^-6 kg) × (9.81 m/s^2) × (0.293 m) = 3.69 × 10^-6 J
The kinetic energy of the froghopper at takeoff can be calculated using the formula:
KE = 0.5mv^2
where KE is the kinetic energy and v is the takeoff speed.
Substituting the given values, we get:
KE = 0.5 × (12.8 × 10^-6 kg) × (2.71 m/s)^2 = 4.75 × 10^-5 J
Therefore, the total energy generated by the froghopper for the jump is the sum of the potential and kinetic energy, which is:
Total energy = ΔPE + KE = 3.69 × 10^-6 J + 4.75 × 10^-5 J = 5.12 × 10^-5 J
Expressing the answer in microjoules, we get:
Total energy = 5.12 × 10^-5 J = 51.2 µJ
b) The energy per unit body mass required for the jump can be calculated by dividing the total energy generated by the froghopper by its body mass.
Substituting the given values, we get:
Energy per unit body mass = (5.12 × 10^-5 J) ÷ (12.8 × 10^-6 kg) = 4 J/kg
Therefore, the energy per unit body mass required for the jump is 4 J/kg.
PLEASE HELP! I AM SO LOST! BRAINLIEST AND 40 PTS!
Answer:
R (total) = 14 Ω
V1 = 68,58 V
V2 = 68,58 V
V3 = 51,42 V
I (total) ≈ 8,57 A
I1 ≈ 4,29 A
I2 = 4,28 A
I3 ≈ 8,57 A
Explanation:
Given:
R1 and R2 are connected in parallel
R3 with (R1 and R2) are connected in series
V (total) = 120,0 V
R1 = 16,0 Ω
R2 = 16,0 Ω
R3 = 6,0 Ω
R (total) = R1 + R2 + R3
First, let's find the resistance in (R1 and R2) part
Since R1 = R2, we can use this formula:
R = R1/n (n is the number of resistors, in this case it's 2)
R = 16/2 = 8 Ω
Now, we add this number to R3 and we'll get the total resistance in this circuit:
R (total) = 8 + 6 = 14 Ω
I (total) = V (total) / R (total)
I (total) = 120/14 ≈ 8,57 A
I3 = I ≈ 8,57 A, since it's connected in series with the current source
V3 = I3 × R3
V3 = 8,57 × 6 = 51,42 V
V1 = V2 = V (total) - V3, since it's a parallel connection
V1 = V2 = 120 - 51,42 = 68,58 V
I1 = V1/R1
I1 = 68,58/16 ≈ 4,29 A
I2 = I (total) - I1
I2 = 8,57 - 4,29 = 4,28 A
I hope I did everything correct
How can 2-phenylethanoic acid can be prepared from toluene?
Answer: C6H5CH3 (toluene) + Br2 + Mg + CO2 + oxidizing agent → C6H5CH2COOH (2-phenylethanoic acid)
Explanation:
2-Phenylethanoic acid, also known as phenylacetic acid, can be prepared from toluene through the following steps:
Bromination: Toluene is brominated using Br2 and FeBr3 as a catalyst to form 2-bromotoluene.
Grignard reaction: The 2-bromotoluene is reacted with magnesium (Mg) in dry ether to form phenylmagnesium bromide (C6H5MgBr).
Acidification: The phenylmagnesium bromide is then reacted with carbon dioxide (CO2) to form 2-phenylpropanoic acid (also known as phenylpropionic acid). This reaction is carried out by bubbling CO2 gas through the solution of phenylmagnesium bromide in dry ether.
Oxidation: The 2-phenylpropanoic acid is then oxidized using a strong oxidizing agent, such as potassium permanganate (KMnO4) or chromic acid (H2CrO4), to form 2-phenylethanoic acid.
The overall reaction can be represented as follows:
C6H5CH3 (toluene) + Br2 + Mg + CO2 + oxidizing agent → C6H5CH2COOH (2-phenylethanoic acid)
Note: This is a complex reaction sequence and should only be attempted by experienced chemists in a well-equipped laboratory with appropriate safety measures.
Ronaldo has two pots of water. Pot 1 has a large number of particles, moving slowly on average. Pot 2 has a smaller number of particles, but they are moving faster on average.
Match the pot with its description.
Pot 1
Pot 2
[ Choose ]
I Choose I
Has a higher kinetic energy
Has a hicher kinetic energy and a higher temperature
Does not have a higher kinetic energy or temperature
Has a higher temperature
The kinetic theory of matter, which holds that all matter is made up of microscopic particles that are always in motion, can be used to explain this situation.
What happens as the particle velocity increases to an object's temperature?When the average kinetic energy of the object's particles increases, so does its thermal energy. The thermal energy of an object therefore increases as its temperature does.
Which example has the most kinetic energy for the water molecules?Water molecules usually have the highest kinetic energy in the steam phase. Since the gaseous phase of a substance always has the highest kinetic energy of the three states of matter, steam is a gaseous state in which water molecules have the highest kinetic energy.
To know more about motion visit:-
https://brainly.com/question/22810476
#SPJ1
Two particles are initially separated by 20 cm. Particle A, with mA = 10pg and qA = -5 nC, is on the left and makes a head-on collision with Particle B at a speed of 4 * 10^4 m/s. Particle B, with mB = 5pg and qB = -10nC, is on the right and moves toward Particle A at a speed of 6 * 10^4 m/s. Assume Particle A is moving in the positive direction. (If you wish to get correct answers, then be sure to use ke = 9 * 10^9 N * m^2 / C^2 and e = 1.6 * 10^-19 C.)
(a) The initial mechanical energy of the system in muJ (μJ - microjoules) and to three decimal places, is?
(b) The magnitude of the maximum force acting on qA during the collision in mN (miliNewton) and to three decimal places, is?
(c) The work done by the electric force on the system to stop the particles in muJ (μJ) and to two decimal places, is?
(d) The minimum separation distance between the two particles in cm and to three decimal places, is?
(e) The maximum speed experienced by Particle A is
Option 1: when it is infinitely far away from Particle B
2: is unable to be determined
3: when it is closest to Particle B
4: at its initial location
5: at a location that cannot be determined without more information
When particle A is infinitely far from particle B, option 1, it moves at its top speed.
Initial velocity of the first particle was u₁ = 4×10 ⁴m/s Initial velocity of the second particle was u₂ = 6×10⁴ m/s Initial velocity of the third particle was v = Final velocity of both particles after collision was v =
Use the idea of linear momentum conservation;
a) After a collision, a 5 kg particle moves at a speed of -1 m/s, changing the total kinetic energy of the system by -40 joules. More kinetic energy can be obtained by adding an external substance.k e = 9 ₓ 10⁹ N m² / C² and e = 1.6 ₓ 10⁻¹⁹ C.)
b) The Joule is the unit used to measure kinetic energy, which is the energy that an item stores as a result of motion. The product of a particle's mass and velocity is known as momentum. In order to determine the particle's velocity following a collision, we must first compare the values in the momentum conservation formula, which is provided as:c) m1 and v1 represent the mass and speed of a 10 pg item (before collision)m2, v2 represent the mass and speed of a 10 kilogram item (before collision)
M1, V1 stand for mass and speed.
d) A first particle and a second particle are O.v(m₁+ m₂) = m₁u₁ - m₂u₂.
11 x 2 - 11 x 2 = v( 11 + 11)
22 - 22 = v(22) (22)
0 = 22v = 0/22 = 0
e) After colliding, both particles' final velocities are zeroAs a result, both particles are at rest.
Learn more about particle here
https://brainly.com/question/30296584
#SPJ1
Need help with these two please!! Thank you in advance.
Answer:
I agree with Erikson stages of development that all adolescents and young adults pass through the stage
A basketball has a mass of approximately 624 grams [g] and a volume of 0.25 cubic feet [ft3]. Determine the density of the basketball in units of slug per gallon [slug/gal].
The basketball has a slugs density of 0.0228 per gallon (m/V = 0.0427 slugs/1.8697 gallons) (approximately).
What in density is a slug?Based on normal gravity, the international foot, and the avoirdupois pound, one slug weighs 32.1740 lb (14.59390 kg). An item with a mass of 1 slug would weigh around 32.2 lbf, or 143 N, at the Earth's surface.
We need to apply the following conversion factor to convert grammes to slugs:
1 slug = 14.5939 kg
1 kg = 1000 g
Therefore:
1 slug = 14.5939 kg = 14.5939 x 1000 g = 14593.9 g
So, the mass of the basketball in slugs is:
m = 624 g / 14593.9 g/slug = 0.0427 slugs
To convert from cubic feet to gallons, we need to use the following conversion factor:
1 gallon = 0.133681 ft^3
Therefore:
0.25 ft⁻³ = 0.25 / 0.133681 = 1.8697 gallons
So, the volume of the basketball in gallons is:
V = 1.8697 gallons
The density of the basketball in slug/gal is:
ρ = m / V = 0.0427 slugs / 1.8697 gallons = 0.0228 slug/gal (approximately)
To know more about slugs density visit:-
https://brainly.com/question/30024936
#SPJ1
EARTH AND SPACE SCIENCE!
All of the following are Kepler's laws of planetary motion EXCEPT?
a.) Planets follow elliptical orbits with the sun at one of its foci
b.) The period of a planet (time it takes to go around the sun) is related to its distance from its Sun
c.) The period of a planet(time it takes to go around the sun) is related to the planet's mass
C. The period of a planet (time it takes to go around the sun) is not related to its mass.
The first law states that the planets follow elliptical orbits with the sun at one of its foci, the second law states that an imaginary line drawn from the sun to a planet sweeps out equal areas in equal times, and the third law states that the square of the period of a planet is directly proportional to the cube of its average distance from the sun. Since the period of a planet is not related to its mass, answer C is not one of Kepler's laws of planetary motion.
learn more about Kepler's laws Refer:brainly.com/question/30760148
#SPJ1
Hanif is the tallest player in a volleyball team. He is in spiking position when Johan delivers him the ball. The 0.226-kg volleyball is 2.29 m above the ground and has a speed of 1.06 m/s. Hanif spikes the ball, doing 9.89 J of work on it. (a) Determine the potential energy and the kinetic energy of the ball before Hanif spikes it. (b) The total mechanical energy of the ball before Hanif spikes it.
(a)
Potential Energy = 4.95 J
Kinetic Energy =0.132 J
b.) the total mechanical energy of the ball before Hanif spikes it is 5.08 J.
How to calculate?Potential energy (PE) = mgh
Kinetic energy (KE) = (1/2)mv^2
m = 0.226 kg
h = 2.29 m
v = 1.06 m/s
g = 9.81 m/s^2 (acceleration due to gravity)
PE = mgh = (0.226 kg)(9.81 m/s^2)(2.29 m) = 4.95 J
KE = (1/2)mv^2 = (1/2)(0.226 kg)(1.06 m/s)^2 = 0.132 J
(b) The total mechanical energy of the ball before Hanif spikes it is the sum of its potential and kinetic energy:
Total mechanical energy = PE + KE = 4.95 J + 0.132 J = 5.08 J
Learn more about kinetic energy at: https://brainly.com/question/8101588
#SPJ1
A 15.0 cm tall object is placed 35.0 cm from a convex lens, which
has a focal length of 15.0 cm. Calculate the height for the image.
The image is reversed if the image height has a negative sign. The image is inverted and has a height of -6.45 cm.
How is the image's height determined?The lens equation describes how a convex lens's object distance (d o), image distance (d i), and focal length (f) relate to one another:
1/f = 1/d_o + 1/d_i
1/d_i = 1/15.0 cm - 1/35.0 cm 1/d_i = 1/f - 1/d o
1/d_i = 0.0667 cm -1
d_i = 15.0 cm
The image's magnification (M) is determined by:
M = - d_i / d_o
M = -15.0 cm / 35.0 cm
M = -0.43
M = h_i / h_o
h_i = M x h_o
The value for h_o is 15.0 cm. With M = -0.43, we obtain:
h_i = -0.43 * 15.0 cm
h_i = -6.45 cm
To learn more about convex lens visit:
brainly.com/question/27038900
#SPJ1
In scratch, a Sensing block, such as touching edge , can be combined with a(n) _____ block, such as not , to create a new condition.
Data
Motion
Operator
Events
Blocks of colored instructions are connected to create programs. Scripts are the name for these collection of blocks. They direct on-screen characters in what to do.
What are movement and an example?Motion can be characterized as a shift in an object's location with regard to time. Motion can be heard in a variety of sounds, such a book sliding off a table, water running from a faucet, rattling windows, etc. There is motion even in the air we breathe! The universe is a moving thing.
What effects motion has?Delete your calendars, task lists, and project management software. Motion uses AI to schedule your day and the days of your team! Your projects, tasks, and meetings are required.
To know more about Motion visit:
https://brainly.com/question/22810476
#SPJ1
1. a) Find the diffusion coefficient of copper-silver penetration at 500°C. b) For this system, what time is required to achieve the same results (the same size at the same distance) of the diffusion process at 500°C for 10 hours at 600°C? ? 2. The iron-carbon alloy with FCC structure initially content, and its surface was exposed to an environment with C = 1.0% carbon content and carbonization treatment was carried out by increasing the ambient temperature. If after 49.5 hours the alloy has a carbon content of 0.35%C at a depth of 2 = 4.0mm from the surface, at what temperature was this heat treatment carried out? C = 0,20% C 334
The time required to achieve the same diffusion results at 500°C for 10 hours at 600°C is approximately 1.1 minutes.
What is Diffusion?
Diffusion is a physical process where molecules or particles move from an area of high concentration to an area of lower concentration. This movement is driven by the natural tendency of molecules to spread out and achieve a state of equilibrium, where the concentration is the same throughout the system. Diffusion occurs in gases, liquids, and solids, and is responsible for a wide range of phenomena, from the movement of oxygen and carbon dioxide in the lungs to the mixing of chemicals in a beaker.
a) The diffusion coefficient of copper-silver penetration at 500°C can be calculated using Fick's first law:
J = -D*(dc/dx)
where J is the diffusion flux, D is the diffusion coefficient, dc/dx is the concentration gradient.
Assuming that copper and silver diffuse independently and the concentration gradient is constant, we can write:
J = -Dc*(dc/dx)
where Dc is the effective diffusion coefficient for copper in silver.
At 500°C, the value of Dc for copper in silver is approximately 2.7 x 10^-11 m^2/s.
b) To determine the time required to achieve the same diffusion results at 500°C for 10 hours at 600°C, we can use the Arrhenius equation:
D2/D1 = exp(-Q/R)*exp((1/T1) - (1/T2))
where D1 and T1 are the diffusion coefficient and temperature at 500°C, D2 and T2 are the diffusion coefficient and temperature at 600°C, Q is the activation energy for diffusion, and R is the gas constant.
Assuming that the activation energy for diffusion is 100 kJ/mol, we can calculate the diffusion coefficient at 600°C:
D2 = D1exp(-Q/R)exp((1/T1) - (1/T2))
= 2.7 x 10^-11 m^2/s * exp(-100000/(8.314500))(1/773 - 1/873)
= 1.3 x 10^-9 m^2/s
Now, we can use Fick's second law to determine the distance traveled by diffusion in 10 hours at 600°C:
x = sqrt(4Dt)
= sqrt(4*(1.3 x 10^-9 m^2/s)*36000 s)
= 0.016 m
To achieve the same diffusion results at 500°C, the same distance must be traveled. Therefore, we can calculate the time required at 500°C:
t = x^2/(4D1)
= (0.016 m)^2/(4*(2.7 x 10^-11 m^2/s))
= 0.019 hours
Learn more about Diffusion from given link
https://brainly.com/question/94094
#SPJ1
You are driving your car through a roundabout that has a radius of 11 m. Your physics textbook is lying on the seat next to you.
What is the fastest speed at which you can go around the curve without the book sliding? The coefficient of static friction between the book and the seat is 0.40.
The formula v = sqrt(grs), where v is the speed and g is the radius, can be used to determine the quickest speed at which you can navigate the curve without the book sliding is the acceleration due to gravity, r is the radius of the curve, and μs is the coefficient of static friction.
What distinguishes kinetic friction from static friction??Static friction is the friction that exists between two objects that are not moving relative to each other, while kinetic friction is the friction that exists between two objects that are moving relative to each other. The force of static friction is typically greater than the force of kinetic friction.
How does the coefficient of friction affect the force of friction between two surfaces?The force of friction between two surfaces is directly proportional to the coefficient of friction, with the equation Ff = μFn, where Ff is the force of friction, μ is the coefficient of friction, and Fn is the normal force between the two surfaces. A higher coefficient of friction means a greater force of friction, and vice versa.
To know more about speed,visit:
https://brainly.com/question/28224010
#SPJ1