Which mineral property is associated with breaking on planes? A), Crystal form.
B), Cleavage.
C), Hardness.

A backsaw is the saw that is best suited for cutting mitre joints. For precise tasks like cutting dovetails, mitres, or tenons in cabinetry and joinery, backsaws are typically used in woodworking.

Any hand saw with a stiffening rib on the edge opposite the cutting edge known as a backsaw enables better control and more accurate cutting than other saws. For precise tasks like cutting dovetails, mitres, or tenons in cabinetry and joinery, backsaws are typically used in woodworking. Backsaws can only cut a certain amount of depth due to the stiffening rib. Backsaws typically have teeth that are closely spaced and frequently have little to no set.

Visit here to learn more about the Backsaw: https://brainly.com/question/28957018

#SPJ4

Answer:

they trap coarse particulate contamination and copper shavings

The correct answer is  I do not have access to any figure or visual representation of the building plan you mentioned. Hence, I am unable to provide an accurate calculation for the required square footage of waterproofing material.

However, I can provide you with a general idea of the steps you need to take to calculate the required square footage. Firstly, you need to determine the total perimeter of the building by adding the length of all sides together. Then, subtract the openings such as doors and windows from the total perimeter.  Next, you need to determine the height of the wall section that needs to be waterproofed. Measure the distance from the top of the wall down to the top of the footing. Once you have the total perimeter and height of the wall section, you can calculate the square footage required for waterproofing. Simply multiply the perimeter by the height of the wall section to get the total square footage. It's also important to consider any additional factors such as overlaps and waste that may affect the amount of waterproofing material needed. Always remember to add a little extra material to ensure adequate coverage and avoid running short during installation.

To learn more about waterproofing material click on the link below:

brainly.com/question/16363151

#SPJ1

Answer: point A[{-40i + 0j + 45k}], B[{0i + 0j + 60k}], C[{ 60i + 0j + 60k}] from there you can now find the Magnitudes then The unit vectors multiplied by the forces provided 425lb AB and 510lb AC.

Explanation:

A method statement for site setup and temporary works in construction should include the following steps:

1. Identify the scope of work and establish the project requirements for site setup and temporary works. This includes the location, size, and nature of the project, as well as any specific regulatory or safety requirements.

2. Develop a detailed plan for site setup and temporary works, including timelines, resources, and responsibilities. This should include a list of all temporary works required, such as access roads, fencing, and scaffolding.

3. Identify potential hazards and risks associated with site setup and temporary works, and develop a risk assessment and mitigation plan. This should include measures to ensure the safety of workers and the public, as well as measures to protect the environment.

4. Obtain all necessary permits and approvals, including building permits, environmental permits, and safety certifications.

5. Develop a site-specific safety plan and ensure all workers are properly trained and equipped to carry out the work safely. This should include safety procedures for working at heights, using heavy equipment, and handling hazardous materials.

6. Monitor the progress of site setup and temporary works, and make adjustments as necessary to ensure the work is completed on time, within budget, and to the required quality standards.

7. Conduct regular inspections and audits to ensure that all site setup and temporary works are in compliance with regulatory and safety requirements.

8. Document all site setup and temporary works activities, including any incidents or accidents that occur, and use this information to improve future projects.

Overall, the method statement for site setup and temporary works in construction should be a detailed plan that outlines all the necessary steps, resources, and safety measures required to ensure the successful completion of the project. It should be regularly reviewed and updated as necessary to ensure that the work is carried out safely and efficiently.

To answer the question about a system that is not determinate:

1. A system is not determinate if it lacks a unique and predictable solution or outcome. This could be due to insufficient constraints, inconsistent information, or the presence of multiple solutions that satisfy the given conditions.

2. To make a non-determinate system determinate, you should add elements to the precedence relation. The precedence relation defines the order in which tasks or events must occur. By introducing new constraints or relationships between the elements, you can reduce ambiguity and ensure a unique solution or outcome. Follow these steps:

  a. Identify the elements in the system that are causing indeterminacy.
  b. Determine the necessary constraints or relationships that will provide a clear order or hierarchy among these elements.
  c. Add the new constraints or relationships to the precedence relation, ensuring that they do not contradict any existing information.
  d. Verify that the modified system now has a unique and predictable solution or outcome, making it determinate.

Learn more about hierarchy here:

https://brainly.com/question/9647678

#SPJ11

29,430 J of work is required to raise a mass of 500 kg to a height of 6 m in 30 seconds (Joules).

F = m 9.8 m/s2 is the formula for computing weight, where m is the object's mass in kilogrammes and N is the object's weight in Newtons (N). The SI unit for weight is the Newton, and one Newton is equal to 0.225 pounds.

work = force x distance

weight = mass x gravity

weight = 500 x 9.81

weight = 4905 N

Now, we can calculate the work done:

work = force x distance

work = weight x height

work = 4905 x 6

work = 29,430 J

To know more about mass visit:-

https://brainly.com/question/16200632

#SPJ1

The Delivery Truck class is designed to manage a collection of Mail objects. It has a single member variable called mail_list, which is an array of length 10 that holds the Mail objects.

The load method takes a Mail object as an argument and stores it in the mail_list array at the next available spot. It does this by checking the current value of a member variable called next_available_spot, which keeps track of the index of the next available spot in the array. If there is space in the array, the Mail object is stored at the index indicated by next_available_spot, and next_available_spot is incremented. If the array is full, the load method does not add the Mail object and returns an error message or raises an exception.

To know more about mail_list click here:

brainly.com/question/20435559

#SPJ4

Answer:Overflowing drains are often caused by sanitary products, paper towels or other hard to flush materials which can clog pipes and obstruct drains. Wipes, tissues, and even hair can also be the culprits

Explanation:

A safety committee is a group of staff members and management who work together to discover, assess, and control workplace risks as well as to encourage worker awareness of and adherence to safety procedures.

To help establish and maintain a safe workplace, management and employees collaborate on a safety committee. Any factory or industrial facility with 50 or more employees is required by law to have one.

Safety committees and meetings serve the objective of bringing management and employees together in a non-competitive, cooperative endeavour to advance safety and health. You may keep improving your safety and health programme by using safety committees and meetings.

To know more about management visit:-

brainly.com/question/30468659

#SPJ1

Answer: To find the total real, reactive, and apparent power used by the facility, we need to calculate the power consumption of each individual load first.

Explanation:

a. The power consumed by the 50hp motor is given by:

P = (50 hp) / (0.86 × 0.70) = 83.63 kW

The reactive power consumed by the motor is given by:

Q = P × tan(cos⁻¹(0.70)) = 57.63 kVAR

b. The power consumed by the 100hp motor is given by:

P = (100 hp × 0.82) / 0.89 = 91.01 kW

The reactive power consumed by the motor is given by:

Q = P × tan(cos⁻¹(0.80)) = 54.72 kVAR

c. The power consumed by each of the two 20hp motors is given by:

P = (20 hp) / (0.92 × 0.85) = 25.08 kW

The reactive power consumed by each motor is given by:

Q = P × tan(cos⁻¹(0.85)) = 14.07 kVAR

d. The power consumed by the 300hp motor is given by:

P = (300 hp × 0.75) / 0.92 = 245.11 kW

The reactive power consumed by the motor is given by:

Q = P × tan(cos⁻¹(0.84)) = 160.89 kVAR

e. The power consumed by the incandescent lighting is given by:

P = 50 kW

The reactive power consumed by the lighting is zero, since it is a resistive load.

Now we can find the total real, reactive, and apparent power used by the facility:

Total real power = 83.63 kW + 91.01 kW + 2 × 25.08 kW + 245.11 kW + 50 kW = 529.91 kW

Total reactive power = 57.63 kVAR + 54.72 kVAR + 2 × 14.07 kVAR + 160.89 kVAR + 0 kVAR = 301.98 kVAR

Total apparent power = √(529.91² + 301.98²) = 609.57 kVA

The total power factor is given by:

cos(θ) = 529.91 kW / 609.57 kVA = 0.8691

θ = cos⁻¹(0.8691) = 29.59 degrees

Therefore, the total power factor is 0.869 lagging. The real power used by the facility is 529.91 kW, the reactive power used is 301.98 kVAR, and the apparent power is 609.57 kVA.

SPJ11

Answer:

  short circuit

Explanation:

You want to know what type of circuit fault is characterized by current bypassing all or some of the electrical load in the circuit.

When the current in a circuit follows a shorter (or lower-impedance) path than the one intended, bypassing some or all of the intended load, the circuit is said to suffer from a "short circuit."

Total energy change = PE + KE + Energy consumed = 6500 J + 284859 J + 8.82 * 10^9 J ≈ 8.82 * 10^9 J

To find the total energy change, we need to consider the potential energy gained (due to elevation increase), kinetic energy gained (due to increase in speed), and the energy consumed from gasoline.

Potential energy change (PE) = m * g * h = (3700 lbm * 0.453592 kg/lbm) * 9.81 m/s² * (6500 N / (3700 lbm * 0.453592 kg/lbm * 9.81 m/s²)) = 6500 J

Kinetic energy change (KE) = 0.5 * m * (v_f² - v_i²) = 0.5 * (3700 lbm * 0.453592 kg/lbm) * ((68 mph * 0.44704 m/s/mph)² - 0) ≈ 284859 J

Energy consumed from gasoline = Energy per gallon * gallons used = (1.2 * 10^8 J/gallon) * (234 miles / 32 mpg) ≈ 8.82 * 10^9 J

Total energy change = PE + KE + Energy consumed = 6500 J + 284859 J + 8.82 * 10^9 J ≈ 8.82 * 10^9 J

Most of the energy went into overcoming the car's internal inefficiencies (engine, transmission, etc.) and external resistances (air drag, rolling resistance). The remaining energy was used to increase the car's potential and kinetic energy.

Read more about energy change here:

https://brainly.com/question/23883411

#SPJ1

(c) A baseband signal is a good example of a message signal as it carries the actual information to be transmitted, while (a) and (b) are typically used for carrier signals.

Out of the given options, a baseband signal is a good example of a message signal. This is because a baseband signal carries the actual information to be transmitted, such as audio or video data, while a radio frequency (RF) signal or a pilot carrier is typically used for the carrier signal, which is modulated by the message signal to carry the information over the transmission medium.

The baseband signal is a low-frequency signal that contains the original information to be transmitted, and it is typically in the range of a few hundred Hertz to a few megahertz. The carrier signal is a high-frequency signal that is modulated by the baseband signal, and it is typically in the range of tens to hundreds of megahertz or even higher. Together, the baseband signal and the carrier signal form the modulated signal that is transmitted over the communication channel.

Learn more about baseband signal here:

brainly.com/question/15831249

#SPJ1

To determine the percentage of the moment that is resisted by the web of the beam, we need to find the moment of inertia of the entire cross-section of the beam, as well as the moment of inertia of just the web. The moment of inertia of the web represents the portion of the total moment that is resisted by the web.

Assuming a rectangular beam with dimensions b (width), h (height), and t (thickness of the web), the moment of inertia of the entire cross-section can be calculated as:

I_total = (1/12) * b * h^3

The moment of inertia of just the web can be calculated as:

I_web = (1/12) * t * h^3

The moment of the applied load is 15 kip-ft. To determine the percentage of this moment that is resisted by the web, we can use the formula:

% resisted by web = (I_web / I_total) * 100%

Substituting the expressions for I_web and I_total, we get:

% resisted by web = [(1/12) * t * h^3 / (1/12) * b * h^3] * 100%

Simplifying the expression, we get:

% resisted by web = (t/b) * 100%

Therefore, the percentage of the moment that is resisted by the web of the beam is equal to the ratio of the thickness of the web to the width of the beam, multiplied by 100%.

For more questions like percentage visit the link below:

https://brainly.com/question/31215720

#SPJ11

Explanation:

The calculation is as follows:

The general lighting load is 10,000 VA.

The voltage used in homes is typically 120 volts.

Dividing the general lighting load by the voltage gives us the amperage: 10,000 VA / 120 volts = 83.33 amps

According to the National Electrical Code (NEC), a 15-amp branch circuit can handle a maximum of 15 amps.

To determine the number of 15-amp branch circuits required, we divide the amperage by the maximum allowed on one circuit: 83.33 amps / 15 amps = 5.55

Therefore, we need at least 6, 15-amp branch circuits to handle the general lighting load of 10,000 VA.

The answer is (D) 6.

FAY = 62.4 lb/ft^3 * 7.01 ft^3/s * 11.67 ft/s * sin(30 degrees) ≈ 674 lbs

Thus, the flow rate through the bend is approximately 7.01 ft^3/s, and the y-direction anchoring force required to hold the bend in place is approximately 674 lbs.

A vector is a quantity or phenomenon that has two independent properties: magnitude and direction. The term also denotes the mathematical or geometrical representation of such a quantity.

It is claimed that two vectors are equal if their magnitude and direction are the same. The study of mathematics, physics, and engineering are all dependent on it. The basic ideas of vector algebra may be used to add one vector to another vector head to tail.

As follows

|v⃗ |=|v1→+v2→|

one which is held

|v| = v21 + v22 + 2 v1 v 2 cos,

angle that the two vectors make with one another. cognizant of

v22 = 144 and v21 = 81 correspondingly.

2(9)(12)cosθ=216(−7,591×10−3)=−1639,656×10−3

so that we have

144+81−1,639656=223,360344

√=14,94524486=|v⃗ |

The angle being taken

θ=(90−63)+(90−α) \s,

In order for the angle we compute to be the angle that really results, for instance, an angle where is the angle between the positive axe-y and the v1.

learn more about vectors here:

https://brainly.com/question/29740341

#SPJ1

Answer:

periscopes, microscopes, telescopes, and cameras.

Answer:

   1. Keep it clean: Use a soft, lint-free cloth or a specialized lens cleaning cloth to clean the lenses of the optical instrument. Avoid using rough materials or paper towels as they can scratch the lenses. Also, be careful when cleaning as some lenses are coated and can be damaged if they come into contact with liquids or certain cleaning solutions.

   2. Store it properly: When not in use, store the optical instrument in a protective case or bag. This will protect it from dust, scratches, and other potential damage. Avoid leaving the instrument in direct sunlight or extreme temperatures, as this can cause the lenses to warp or crack.

   3. Handle it with care: When using the instrument, handle it with care to avoid dropping or knocking it. Many optical instruments are fragile and can be damaged easily. Be particularly careful with any moving parts or delicate mechanisms.

   4. Regular maintenance: Depending on the type of optical instrument, it may require periodic maintenance, such as calibration or alignment. Follow the manufacturer's instructions for maintenance, or consult a professional if you are unsure of how to properly maintain the instrument. Regular maintenance can help to prolong the life of the instrument and ensure that it performs accurately.

The allowed range of mass flow rates for water, in kg/s is 23.56 - 30.44.

Given,

The mass flow rate of oil, m₁ = 10 kg/sThe inlet temperature of oil, T₁ = 450 kThe exit temperature of oil, T₂ = 350 kThe inlet temperature of water, T₃ = 208 °C = (208 + 273) K = 481 K

The inlet pressure of water, P₃ = 5 bar = 500 kPaThe specific heat of oil, c = 2 kJ/kgK

We can calculate the heat transferred to water by the oil using the heat balance equation as:

q = m₁c(T₁-T₂)

Where,q = Heat transferred to water by oilm₁ = mass flow rate of oilc = specific heat of oilT₁ and T₂ = inlet and exit temperature of oil respectively

Substituting the values in the equation,q = 10 × 2 × (450-350)q = 2000 kJ/sThe heat transferred to water is equal to the heat gained by water, i.e.,q = m₂c(T₄-T₃).

Where,m₂ = mass flow rate of waterc = specific heat of waterT₃ and T₄ = inlet and exit temperature of water respectively.

Substituting the values in the equation,2000 = m₂ × 4.18 × (481 - T₄)T₄ = 481 - (2000 / (m₂ × 4.18))

Range of mass flow rates for water, can be calculated by assuming the exit temperature of water to be 100 °C (373 K).481 - (2000 / (m₂ × 4.18)) = 373m₂ = 28.12 kg/s481 - (2000 / (m₂ × 4.18)) = 373m₂ = 25.64 kg/s

Therefore, the allowed range of mass flow rates for water, in kg/s is 23.56 - 30.44.

Learn more about inlet temperature

brainly.com/question/30137358

#SPJ11

To prevent aliasing, the anti-aliasing filter's cutoff frequency should be less than half of the sampling frequency (Nyquist frequency). Therefore, for a signal to be sampled at 1 kHz, the cutoff frequency of the anti-aliasing filter should be less than 500 Hz.

When sampling an analog signal, it is important to ensure that the resulting digital signal accurately represents the original signal. Aliasing can occur when the signal is not properly sampled, resulting in distortion or errors in the digital signal.

To prevent aliasing, an anti-aliasing filter is used to remove any frequency components above the Nyquist frequency, which is half the sampling rate. In this case, the signal is to be sampled at 1 kHz, so the Nyquist frequency is 500 Hz.

Therefore, the cutoff frequency of the anti-aliasing filter should be set at or below 500 Hz to prevent any frequency components above the Nyquist frequency from being sampled and causing aliasing. A good rule of thumb is to set the cutoff frequency at about 70% of the Nyquist frequency, so a cutoff frequency of around 350 Hz would be appropriate in this case.

Learn more about aliasing here brainly.com/question/14983964

#SPJ4

The correct definition for the word Decimal is a shortened version of the term "decimal fraction.A decimal is a fraction that has a denominator of ten, hundred, thousand, or any other power of ten.

Decimals are a way of expressing parts of a whole, especially when dealing with fractional values. They are often used in money calculations, measurement, and science to give precise values.The decimal system is a method of organizing numbers that employs the digits 0 through 9. It is based on the powers of ten and place values. Decimal fractions can subtracted, added,  multiplied, and divided like whole numbers, making them simple to work with.

Learn more about Decimal here:

https://brainly.com/question/28338004

#SPJ4

When capacitors are connected in series, the total capacitance is given by:

1/C_total = 1/C_1 + 1/C_2 + 1/C_3 + 1/C_4

Substituting the values given, we get:

1/C_total = 1/14 + 1/14 + 1/14 + 1/14
1/C_total = 4/14
C_total = 3.5 μF

Therefore, the minimum capacitance that can be obtained by connecting four 14- μf capacitors in series is 3.5 μF.

When capacitors are connected in parallel, the total capacitance is simply the sum of the individual capacitances. Therefore, the minimum capacitance that can be obtained by connecting four 14- μf capacitors in parallel is:

C_total = 4 * 14 μF
C_total = 56 μF

Therefore, the minimum capacitance that can be obtained by connecting four 14- μf capacitors is 3.5 μF in series and 56 μF in parallel.

Learn more about capacitors here:

https://brainly.com/question/29100869

#SPJ11

The aim of the content planning process is to create a content strategy that aligns with your organization's goals and objectives. This process involves developing information and ideas through research, analysis, and creative thinking.

The process typically includes the following steps:
1. Define your audience: In this step, you need to identify the audience you want to target with your content. This can be done by analyzing your existing customer base or by conducting market research to understand the needs and interests of your target audience.
2. Set goals and objectives: You need to establish clear goals and objectives for your content marketing efforts. These goals should be specific, measurable, achievable, relevant, and time-bound (SMART). For instance, your goal may be to increase brand awareness, generate leads, or boost sales.
3. Develop a content strategy: Once you have identified your audience and set your goals, you need to develop a content strategy that will help you achieve these objectives. This involves identifying the types of content you will create, the channels you will use to distribute it, and the key messages you want to communicate.
4. Create a content calendar: A content calendar is a schedule that outlines the topics, formats, and channels you will use to distribute your content over a specified period. This helps ensure that your content is timely, relevant, and consistent.
5. Execute your plan: Once you have developed your content plan, you need to execute it by creating and publishing your content. You should also track your progress and adjust your strategy as needed to ensure that you are meeting your goals.

For such  more questions on planning process:

brainly.com/question/27989299

#SPJ11

The given statement "an engineering notebook is used for documenting all research, proving the origin of an idea, keeping sketches in one place, and a personal calendar" is true because an engineering notebook is a type of journal or logbook used by engineers.

It is often used to track the evolution of a project or to prove the origin of a particular concept or invention. In addition to keeping sketches in one place and serving as a personal calendar, an engineering notebook is also useful for maintaining accurate records and staying organized.

An engineering notebook is a written record of an engineer's ideas, observations, designs, and experiments. It serves as a legal document that provides evidence of the engineer's work.

Learn more about engineering notebook: https://brainly.com/question/11250014

#SPJ11

Answer:

To determine the compressibility and bulk modulus of elasticity of a gas, we can use the following formulas:

Compressibility:

β = - (1/V) * (∆V/∆P)

where V is the initial volume of the gas, ∆V is the change in volume, and ∆P is the change in pressure.

Bulk modulus of elasticity:

B = - V * (∆P/∆V)

where V is the initial volume of the gas, ∆V is the change in volume, and ∆P is the change in pressure.

Using the given values, we can calculate the compressibility as follows:

∆V = V2 - V1 = 0.111m3 - 0.30m3 = -0.189m3

∆P = P2 - P1 = 202.8kPa - 50.7kPa = 152.1kPa

Therefore,

β = - (1/0.30m3) * (-0.189m3/152.1kPa) ≈ 0.0048 kPa^-1

Similarly, we can calculate the bulk modulus of elasticity as follows:

B = - 0.30m3 * (152.1kPa/-0.189m3) ≈ 2418 kPa

Therefore, the compressibility of the gas is approximately 0.0048 kPa^-1, and the bulk modulus of elasticity is approximately 2418 kPa.

Explanation:

In many ways, uncertainty is essential to science because it motivates researchers to conduct additional studies and research.

Being free of uncertainty is a major driving force behind many actions and decisions because the desire for certainty is a strong human emotion. We never know how decisions or actions will turn out, even when we seem to put uncertainty to rest—we pick a career, our elected officials tighten laws to address pollution, the Federal Reserve Board lowers interest rates to boost economic activity. Whether we like it or not, there is always uncertainty.

But a lot of us tend to believe that science offers conclusive solutions. In the end, science explains how and why things occur. Science is a problem-solver. Future predictions are made by scientists.

However, despite our desire for scientific findings to be indisputable, they are not. Scientists can't work with absolute certainty. Probabilities are used to base conclusions. Predictions can be proved wrong by new information, and well-established theories can even be changed. In many ways, uncertainty is essential to science because it motivates researchers to conduct additional studies and research.

Visit here to learn more about the Scientists: https://brainly.com/question/12965344

#SPJ4

A gravitational force of 4.93 10-12 N in the positive x-direction is applied by the copper sphere to the steel sphere.

Along the line connecting the centres of the two objects, the force is applied. Coulomb's law has an undesirable effect if the two charges have opposing signs. This indicates that there is an attractive force acting on the particles.

[tex]F = G * m1 * m2 / r^2[/tex]

[tex]m = rho * (4/3) * pi * r^3[/tex]

r = 65 mm = 0.065 m

a = 3.7r = 0.241 m

b = 2.1r = 0.137 m

c = 0.6r = 0.039 m

m_copper = rho_copper [tex]* (4/3) * pi * r^3[/tex]

[tex]= 8,960 kg/m^3 * (4/3) * pi * (0.065 m)^3[/tex]

= 0.0138 kg

m_steel = rho_steel [tex]* (4/3) * pi * r^3[/tex]

= [tex]7,860 kg/m^3 * (4/3) * pi * (0.065 m)^3[/tex]

= 0.0119 kg

F = G  m_copper  m_steel / [tex]r^2[/tex]

= [tex]6.674 × 10^-11 N·(m/kg)^2 * 0.0138 kg * 0.0119 kg / (0.065 m)^2[/tex]

[tex]= 4.74 × 10^-11 N[/tex]

u = (0.241 - 0.137)i + 0j + 0k

= 0.104i + 0j + 0k

So the gravitational force F can be expressed as:

[tex]= 4.74 × 10^-11 N[/tex]

[tex]= 4.74 × 10^-11 N[/tex]

To know more about force visit:-

https://brainly.com/question/30478824

#SPJ1