what is the x-component of the magnetic force on a 1-m length section of i1? express your answer in micronewtons.

The frictional torque on the flywheel is equal to -43.6 Nm.

In order to determine the frictional torque on the flywheel, we would have to convert the unit of the initial angular speed in rev/min and time in minutes to rad/s and seconds respectively.

This ultimately implies that, we would multiply the initial angular speed  by 2π/60;

Note: 1 rev = 2π radian and 1 minute = 60 seconds.

Initial angular speed, ω₁ = 500.0 × (2π/60)

Initial angular speed, ω₁ = 52.36 rad/s

Final angular velocity, ω₂ = 0 rad/s (since the flywheel came to rest)

Time taken to stop, t = 2.0 minutes to seconds = 2.0 × 60

Time taken to stop, t = 120 s

Next, we would determine the angular deceleration (α) by using this formula:

Angular deceleration, α = (ω₂ - ω₁)/t

Angular deceleration, α = (0 - 52.36)/120

Angular deceleration, α = -0.436 rad/s²

Now, we can determine the frictional torque on the flywheel;

Frictional torque, T = Iα

Frictional torque, T = 100.0 × (-0.436)

Frictional torque, T = -43.6 Nm.

Read more on torque here: brainly.com/question/17512177

#SPJ4

Complete Question:

A flywheel (I = 100.0 kg-m²) rotating at 500.0 rev/min is brought to rest by friction in 2.0 min. what is the frictional torque on the flywheel?

At 1000m above sea level lies the mountain's peak, with an assumed median value of Ta (air temperature) equaling 20°C at the beginning zone.

As wind passes over a mountain, the temperature undergoes changes due to the altitude it reaches during its rise and fall.

At 1000m above sea level lies the mountain's peak, with an assumed median value of Ta (air temperature) equaling 20°C at the beginning zone.

Alongside this, about 80% relative humidity is expected in this range. The two types of adiabatic lapse rates become essential as we shift towards the cooler, i.e., the windward side or warmer lee side when climbing up/down the mountain.

Locations on these sides show different temperatures caused by their distinct warming/cooling rates; thus, modifying sizes, temperature levels, and moisture content of the air particles transported throughout the region.

Read more about temperatures here:

https://brainly.com/question/25677592

#SPJ1

The potential at various points in the circuit are as follows: positive terminal of the battery: 32V, point A: 32V, point B: 32V, point C: 0V, point E: 0V, △VR_1: 16V, and △VR_2: 16V.

Since the potential at the negative terminal of the battery is 0V and the battery voltage is 32V, the potential at the positive terminal is 32V.

In a series circuit, the potential at points A and B is equal to the potential at the positive terminal, which is 32V. Point C is connected to the negative terminal, so its potential is 0V.

Point E is also at 0V as it is connected to the negative terminal as well.

The voltage drops across the resistors R_1 and R_2 are equal because the total resistance is 12 ohms (4+8) and the current is the same throughout the circuit.

The total voltage drop across both resistors is 32V, so the voltage drop across each resistor is half of the total, which is 16V.

Summary: In the given circuit, the potential at different points are: positive terminal - 32V, point A - 32V, point B - 32V, point C - 0V, and point E - 0V. The voltage drops across the resistors R_1 and R_2 are both 16V.

Learn more about circuit click here:

https://brainly.com/question/26064065

#SPJ11

To find the voltage across any of the four resistors in the loop, you can use Kirchhoff's voltage law (KVL), which states that the sum of the voltages around a closed loop must equal zero.

Start at any point in the loop and follow the path, assigning a sign (+ or -) to each voltage depending on the direction of travel. Then, equate the sum of these voltages to zero. This will give you the relationship for finding the voltage across any of the four resistors in the loop.

Thus by using Kirchhoff's voltage law (KVL) we would be able to find the voltage among four resistors.

Learn more about Kirchoff's Law here:- brainly.com/question/86531

#SPJ11

The cost of running the compressor each day would be: 19.11 kWh * 18 cents/kWh = $3.44

To find the energy consumed by the motor daily, we first need to convert the horsepower to watts:

1 horsepower = 750 watts

So, the power consumed by the motor is:

2.8 hp * 750 W/hp = 2100 watts

To find the energy consumed by the motor in 9.1 hours, we can use the formula:

Energy = power * time

Energy = 2100 W * 9.1 h = 19110 Wh

Since 1 kilowatt-hour (kWh) is equal to 1000 watt-hours (Wh), we can convert the energy consumption to kilowatt-hours:

19110 Wh / 1000 = 19.11 kWh

The cost of electricity is given as 18 cents per kilowatt-hour. Therefore, the cost of running the compressor each day would be: 19.11 kWh * 18 cents/kWh = $3.44

Learn more about energy consumed

https://brainly.com/question/862638

#SPJ4

The speed of the proton when it reaches the negative plate is 5.52×[tex]10^{5}[/tex] m/s.

What is Electric Field?

An electric field is a physical field that surrounds electrically charged particles or objects and exerts a force on other charged particles or objects within the field. The electric field at a point in space is defined as the force per unit charge that would be experienced by a small test charge placed at that point.

The potential difference between the plates of the capacitor can also be related to the kinetic energy of the proton as it moves from the positive plate to the negative plate. At the positive plate, the proton has zero kinetic energy and a potential energy of qV, where q is the charge of the proton. At the negative plate, the proton has a kinetic energy of , where m is the mass of the proton and v is its speed.

Since energy is conserved, we can equate the potential energy at the positive plate to the kinetic energy at the negative plate: qV = (1/2)m[tex]v^{2}[/tex]. Solving for v, we get v = V[tex]\sqrt[2qV]/{2qV}[/tex]).

Plugging in the given values, we get v = sqrt(2*(1.602×[tex]10^{-19}[/tex]C)(4.90×[tex]10^{4}[/tex] V/m)(1.70×[tex]10^{-3}[/tex] m)/(1.673×[tex]10^{-27}[/tex] kg)) = 5.52×[tex]10^{5}[/tex] m/s.

Learn more about Electric Field from the given link

https://brainly.com/question/19878202

#SPJ4

The correct options are: Reduce the mass of the Sun to one-fourth its normal value. Increase the separation between the Earth and the Sun to four times its normal value.

The force between the Earth and the Sun is determined by their masses and the distance between them, according to the law of gravitation. Therefore, any change in these parameters will affect the magnitude of the force.

Reducing the mass of the Sun to one-fourth its normal value would decrease the force of gravity on the Earth since the force of gravity is directly proportional to the mass of the Sun.

By reducing the mass of the Sun, the gravitational attraction between the Earth and the Sun would decrease, resulting in a reduced force between them.

Increasing the separation between the Earth and the Sun to four times its normal value would also decrease the force of gravity acting on the Earth. The force of gravity is inversely proportional to the square of the distance between the two objects.

Thus, increasing the distance between the Earth and the Sun by a factor of four would decrease the force of gravity between them by a factor of 16, which would result in a reduction of the force to one-fourth the value found in part a.

In conclusion, reducing the mass of the Sun to one-fourth its normal value and increasing the separation between the Earth and the Sun to four times its normal value would both reduce the magnitude of the force between them to one-fourth the value found in part a.

These changes to the Earth-Sun system can have significant effects on the climate, seasons, and other astronomical phenomena on Earth.

Learn more about mass of the Sun: brainly.com/question/30460050

#SPJ11

a) The initial speed of the bullet (ve) before it hits the block is approximately 44.3 m/s.
b) The mechanical energy lost during the collision is approximately 736.9 J.

a) To find the initial speed of the bullet, we can use the conservation of mechanical energy and momentum. First, we find the final speed (Vf) of the combined system after the collision using potential energy at the highest point of the swing:
mgh = 0.5(M+m)Vf^2
0.5 * 0.0015kg * 9.81m/s^2 * 0.5m = 0.5 * 0.0015kg * Vf^2
Vf = 3.3 m/s
Next, we use the conservation of momentum to find the initial speed of the bullet (ve):
m * ve = (m + M) * Vf
0.05kg * ve = 1.05kg * 3.3 m/s
ve ≈ 44.3 m/s
b) To find the mechanical energy lost, first calculate the initial kinetic energy (KE_initial) of the bullet and the final kinetic energy (KE_final) of the combined system:
KE_initial = 0.5 * m * ve^2 = 0.5 * 0.05kg * (44.3 m/s)^2 ≈ 1099.2 J
KE_final = 0.5 * (m + M) * Vf^2 = 0.5 * 1.05kg * (3.3 m/s)^2 ≈ 362.3 J
Now, subtract the final kinetic energy from the initial kinetic energy to find the mechanical energy lost:
Energy lost = KE_initial - KE_final ≈ 736.9 J

Summary:
The initial speed of the bullet before it hits the block is approximately 44.3 m/s, and the mechanical energy lost during the collision is approximately 736.9 J.

Learn more about speed click here:

https://brainly.com/question/13943409

#SPJ11

Before you back under a semi-trailer when coupling your tractor, the nose of the trailer should be at a height that matches the fifth wheel height on your tractor.

This will ensure a proper and secure connection between the tractor and the trailer, allowing for safe transportation. It is important to always follow the manufacturer's recommendations and safety guidelines when coupling a tractor and trailer.

Before you back under a semi-trailer when coupling your tractor, the height of the trailer's nose should be slightly lower than the fifth wheel on the tractor. This allows for proper alignment and connection between the tractor and the trailer during the coupling process.

To know more about semi-trailer visit:

https://brainly.com/question/14006286

#SPJ11

The inductance of the coil connected to this capacitor is 2.49 x 10^-6 H. The maximum capacitance of the capacitor should be 24.2 pF to cover the full range of the broadcast band.

Part A:

The resonant frequency of an L-C circuit is given by the equation:

[tex]$f = \frac{1}{2\pi\sqrt{LC}}$[/tex]

where f is the oscillation frequency, L is the inductance of the coil, and C is the capacitance of the capacitor.

At the minimum capacitance of 4.15 pF, the oscillation frequency is 1.50 MHz. Plugging these values into the above equation, we can solve for L:

[tex]$1.50 \times 10^6 = \frac{1}{2\pi\sqrt{L \times 4.15 \times 10^{-12}}}$[/tex]

L = 2.49 x 10^-6 H

Part B:

At the other end of the broadcast band, the oscillation frequency is 0.543 MHz. We can use the same equation as before to solve for the maximum capacitance:

[tex]$0.543 \times 10^6 = \frac{1}{2\pi\sqrt{L \times C_{max}}}$[/tex]

Assuming that the inductance of the coil remains the same as before (2.49 x 10^-6 H), we can rearrange the equation to solve for Cmax:

[tex]$C_{max} = \frac{1}{4\pi^2 L (f_{max})^2}$[/tex]

where fmax is the maximum oscillation frequency, which is 1.50 MHz (the frequency at the other end of the broadcast band).

Plugging in the values, we get:

Cmax = 24.2 pF

To learn more about inductance

https://brainly.com/question/29981117

#SPJ4

The Ferris wheel keeps turning, and at a later time, the same child is at location g, with coordinates < -19. 799, -19. 799, 0 > m relative to location a, moving with velocity < 6. 223, -6. 223, 0 > m/s. True.

Assuming that the Ferris wheel continues to rotate at a constant speed and the child remains at the same radial distance from the center, the child's coordinates with respect to location a would change as the ferris wheel rotates. Therefore, it is possible for the child to be at a location with coordinates < -19.799, -19.799, 0 > m relative to location a at a later time.

The child's velocity with respect to location a is given as < 6.223, -6.223, 0 > m/s. This implies that the child is moving in a circular path with respect to the center of the ferris wheel, with a tangential velocity of 6.223 m/s. The velocity vector of the child would also be changing direction as the ferris wheel rotates.

Learn more about child's velocity

https://brainly.com/question/30319473

#SPJ4

The change in internal energy of the gas is 270.1 J

Energy of  must be added to the gas by heat for the indirect path IAF to give the same change in internal energy 1080 J.

The first law of thermodynamics is a thermodynamic adaptation of the law of conservation of energy. "The total energy in a system remains constant, even though it may be converted from one form to another," says one basic expression. Another commonly used phrase is that "energy can neither be created nor destroyed" (in a "closed system"). While there are numerous nuances and consequences that may be conveyed more clearly in more sophisticated formulations, this is the fundamental premise of the First Law. According to first law of thermodynamic amount of heat added to the system  is equal to sum of gain in internal energy and work done.

mathematically,

H = ΔU+W

Given,

Heat H = 498 J

In this problem, in diagonal path, pressure and volume both changes.

W = ΔPΔV

ΔP = 2.5 - 0.5 = 2 atm =202650 Pa

ΔV = 2.5 - 1 = 1.5 L = 0.0015 m³

Work W = ΔPΔV = 202650 × 0.0015 = 303.9 J

Hence change in internal energy in diagonal path is ,

498= ΔU + 303.9

ΔU  = 498 - 303.9 = 194.1 J

The change in internal energy in IAF path is ,

H = ΔU + (ΔPV + PΔV)

H = 194.1 + {202650×0.0025+ 253313×0.0015 )

H = 1080 J

To know more about Heat :

https://brainly.com/question/1429452

#SPJ1.

When a negatively charged plastic rod is brought near the north pole of a metal bar magnet, the pole will turn towards the rod.

This is because the plastic rod induces a temporary magnetic field in the bar magnet which is opposite in polarity to the north pole. As a result, the north pole is attracted to the rod and turns towards it.

Similarly, when the plastic rod is brought near the south pole of the magnet, the south pole will turn towards the rod as the induced magnetic field in the bar magnet is now aligned with the south pole.

Thus, the correct answer is option d) both poles are attracted to the rod.

It is important to note that the strength of the induced magnetic field in the bar magnet is proportional to the strength of the magnetic field of the plastic rod and the distance between the rod and the magnet.

The closer the rod is to the magnet, the stronger the induced magnetic field and the greater the attraction between the rod and the magnet.

To know more about negatively charged refer here

brainly.com/question/7439274#

#SPJ11

No, the pan of water and eggs is not a closed system.

A closed system is defined as a system that does not exchange matter with its surroundings, but can exchange energy. In this scenario, heat is being added to the water by the burner on the stove, and heat is also escaping in the form of steam.

Since the steam seeps out of the pan and lifts the lid, there is an exchange of matter (steam) with the surroundings, which disqualifies it from being a closed system.

Hence, The pan of water and eggs is not a closed system because there is an exchange of matter (steam) with the surroundings.

learn more about heat click here:

https://brainly.com/question/934320

#SPJ11

Main answer:
(a) The tension in the pendulum cable at the lowest point is 4.59 N.
(b) The angle the cable makes with the vertical at the highest point is 68.2 degrees.
(c) The tension in the pendulum cable at the highest point is 1.62 N.

(a) At the lowest point, the tension (T) in the cable is the sum of centripetal force (Fc) and gravitational force (Fg). Fc = (mv^2)/r and Fg = mg.

Therefore, T = Fc + Fg. Given the mass (m) = 0.410 kg, speed (v) = 3.80 m/s, and length of the pendulum (r) = 0.80 m, we can find T.
(b) At the highest point, the pendulum has potential energy (PE) equal to the initial kinetic energy (KE).

We can find the height (h) at the highest point and then use trigonometry to find the angle (θ) with the vertical.
(c) At the highest point, the tension (T) is equal to the difference between gravitational force (Fg) and centripetal force (Fc). We can find T using the calculated height (h) and angle (θ).

Summary:
The tension in the pendulum cable at the lowest point is 4.59 N, and at the highest point, it is 1.62 N. The cable makes an angle of 68.2 degrees with the vertical at the highest point.

Learn more about force click here:

https://brainly.com/question/12785175

#SPJ11

A drainage basin, also known as a watershed or catchment, is an area of land where all surface water flows to a common point, such as a river or lake. This water can come from precipitation, such as rain or snow, or from groundwater that has reached the surface.

To calculate the runoff from a drainage basin, we'll use the SCS Curve Number method. The given curve number is 72 and the rainfall received is 5 inches.

Step 1: Calculate the potential maximum retention (S) using the formula:
S = (1000/CN) - 10
S = (1000/72) - 10
S ≈ 3.89 inches

Step 2: Calculate the initial abstraction (Ia), which is typically assumed to be 0.2S:
Ia = 0.2 * 3.89
Ia ≈ 0.78 inches

Step 3: Calculate the runoff depth (Q) using the formula:
Q = ((P - Ia)^2) / (P - Ia + S)
where P is the total precipitation (5 inches).

Q = ((5 - 0.78)^2) / (5 - 0.78 + 3.89)
Q ≈ 0.62 inches

The runoff from the basin is most nearly 0.62 inches (option b).

To know more about drainage basin visit:

https://brainly.com/question/8445643

#SPJ11

The magnetic flux through the circular loop of wire at the north magnetic pole of the earth will be maximum when the normal to the loop points vertically downward, as this is the direction of the earth's magnetic field. When the normal to the loop points horizontally, the magnetic flux through the loop will be zero as there is no component of the earth's magnetic field perpendicular to the loop.

Therefore, the magnitude of the flux when the normal points are vertically downward is greater than the magnitude of the flux when the normal points are horizontal.


The magnetic flux (Φ) through the loop is given by Φ = B⋅A⋅cosθ, where B is the Earth's magnetic field, A is the area of the loop, and θ is the angle between the magnetic field and the normal to the loop.

At the Earth's north magnetic pole, the magnetic field lines are directed vertically downward.

1. When the normal to the loop points horizontally:
In this case, the angle (θ) between the magnetic field and the normal to the loop is 90°. So, cosθ = cos(90°) = 0. Therefore, the magnetic flux (Φ) is 0.

2. When the normal to the loop points vertically downward:
In this case, the angle (θ) between the magnetic field and the normal to the loop is 0°. So, cosθ = cos(0°) = 1. Therefore, the magnetic flux (Φ) is B⋅A.

Comparing the two situations, the magnetic flux is greater when the normal to the loop points vertically downward.

to know more about circular loop here:

brainly.com/question/28701572

#SPJ11

The energy transported across a 1.40 cm2 area per hour by an electromagnetic wave with an RMS electric field strength of 32.8 mV/m is 4.64 x 10^-4 J.

The energy transported per unit time (power) by an electromagnetic wave is given by:

P = (1/2) * ε * c * E_rms^2 * A

where ε is the permittivity of free space, c is the speed of light in vacuum, E_rms is the root-mean-square electric field strength, and A is the area over which the energy is transported.

Substituting the given values, we get:

P = (1/2) * (8.85 x 10^-12 F/m) * (3 x 10^8 m/s) * (32.8 x 10^-3 V/m)^2 * (1.40 x 10^-4 m^2)

P = 1.29 x 10^-7 W

The energy transported across the given area per hour can be obtained by multiplying the power by the time:

Energy = P * t

where t is the time in seconds. Since we want the energy transported per hour, which is 3600 seconds, we have:

Energy = 1.29 x 10^-7 W * 3600 s

Energy = 4.64 x 10^-4 J

Therefore, the energy transported across a 1.40 cm2 area per hour by an electromagnetic wave with an RMS electric field strength of 32.8 mV/m is 4.64 x 10^-4 J.

Learn more about RMS electric field strength

brainly.com/question/31537926

#SPJ11

When one of the light bulbs burns out in a parallel circuit, it essentially becomes an open circuit. In a parallel configuration, two light bulbs are connected to a 12V battery in such a way that each bulb has its own separate path to the power source. This means that the voltage across each bulb remains the same (12V) and the total current is divided among the bulbs.

When one of the light bulbs burns out in a parallel circuit, it essentially becomes an open circuit, and current can no longer flow through it. However, since the bulbs are connected in parallel, the other bulb still has its own direct path to the power source. This means that the remaining bulb will continue to function normally, receiving the full 12V from the battery.

The total current in the circuit will decrease as there is now only one functioning bulb. However, the overall effect on the circuit is minimal, as the voltage and functioning of the remaining bulb remain unchanged. This is one of the advantages of parallel circuits, as they provide redundancy and ensure that other components continue to operate even if one component fails.

Learn more about circuits here:

https://brainly.com/question/14997346

#SPJ11

The mass of the astronaut who oscillates with a period of 2.09 s when sitting in the chair is 83.3 kg.

We can use the formula for the period of oscillation of a spring-mass system, which is [tex]T=2π\sqrt{\frac{m}{k} }[/tex], where T is the period, m is the mass of the object, and k is the spring constant. In this case, the astronaut is sitting in a chair, which can be considered a spring-mass system with a known spring constant. Therefore, we can solve for the mass of the astronaut by rearranging the formula to [tex]m=(T^2*k)/(4π^2)[/tex].
Using the given period of oscillation (T=2.09 s) and the spring constant of the chair, we get:
[tex]m=(2.09^2*880)/(4π^2)[/tex]=83.3 kg
Therefore, the mass of the astronaut is 83.3 kg.
The period of oscillation formula comes from Hooke's Law and the simple harmonic motion equations. It relates the mass of the oscillating object (in this case, an astronaut) to the time it takes to complete one oscillation (the period) and the spring constant (a measure of the stiffness of the spring).
Without the spring constant value, we cannot calculate the mass of the astronaut using the provided information. If you can provide the spring constant, we will be able to solve for the mass using the formula mentioned above.

For more information on Hooke's Law kindly visit to

https://brainly.com/question/30379950

#SPJ11

a) The total charge of the object is +2 b) The total charge of the object is 0 c) The total charge ofm the object is -3.

a. To determine the total charge of the object, we need to add up the individual charges of the positive and negative charges. Since each positive charge carries a charge of +1 and each negative charge carries a charge of -1, we can calculate the total charge as follows:

Total charge = (4 x +1) + (2 x -1) = +2

Therefore, the object has a total charge of +2.

b. Similar to part a, we can calculate the total charge of the object by adding up the individual charges of the positive and negative charges. Since each positive charge carries a charge of +1 and each negative charge carries a charge of -1, we can calculate the total charge as follows:

Total charge = (30 x +1) + (30 x -1) = 0

Therefore, the object has a total charge of 0, which means it is electrically neutral.

c. Following the same approach as in parts a and b, we can calculate the total charge of the object by adding up the individual charges of the positive and negative charges. Since each positive charge carries a charge of +1 and each negative charge carries a charge of -1, we can calculate the total charge as follows:

Total charge = (13 x +1) + (16 x -1) = -3

Therefore, the object has a total charge of -3.

To know more about charge click here

brainly.com/question/14692550

#SPJ11

Yes, there is a magnetic force on the loop. The magnetic field at the site of the coil may be resolved into a vertical and a horizontal component. The current is clockwise.

As the induced current interacts with the magnetic field of the approaching magnet, the vertical component of the magnetic field results in a force that tries to collapse the coil, and the horizontal component of the magnetic field results in a force that pushes the coil vertically upward. Therefore, the magnetic force on the loop is upward.

In the case of the given scenario, as the loop is rotated, the magnetic field passing through the loop changes, inducing an emf and hence, an induced current in the loop. According to Lenz's Law, the direction of the induced current is such that it opposes the change in magnetic flux that produced it. As a result, the induced current in the loop flows in a clockwise direction.

When the induced current interacts with the magnetic field of the approaching magnet, the vertical component of the magnetic field results in a force that tries to collapse the coil, and the horizontal component of the magnetic field results in a force that pushes the coil vertically upward. Therefore, there is a magnetic force on the loop, and the direction of the force is vertically upward due to the horizontal component of the magnetic field.

Learn more about Magnetic Force here:- brainly.com/question/2279150

#SPJ11

The change in temperature experienced by body b is 5 times that of a.

Mass of the body a, m₁ = 2m

Mass of the body b, m₂ = m

Specific heat of the body a, C₁ = 3C

Specific heat of the body b, C₂ = C

Heat energy of a body,

Q = mCΔT

So, ΔT ∝ 1/mC

So, we can write, the change in temperatures of b and a,

ΔTb/ΔTa = m₁C₁/m₂C₂

ΔTb/ΔTa = 2m x 3C/(m x C)

ΔTb/ΔTa = 5

Therefore, change in temperature experienced by body b,

ΔTb = 5ΔTa

To learn more about specific heat, click:

https://brainly.com/question/21041726

#SPJ1

a. We must compare the number of moles of each reactant utilised in order to identify the limiting reagent. The following formulae can be used to determine how many moles of each reactant there are:

Moles of bromobenzene are calculated as follows: (0.32 mL/1000 mL) * (1 g/1 mL) / 157 g/mol = 2.04 10-3 mol

Mg moles are equal to 0.0072 g/mol (24.3 g/mol = 2.96 10).-4 mol

1.92 x 10-3 mol of acetophenone is equal to 0.23 mL per 1000 mL * 1 g per 1 mL * 120.15 g/mol.

Mg is the limiting reagent since its moles are the lowest.

b. The reaction's equation of equilibrium is

C6H5CH(OH)C6H5 + MgBr2 + 2 HBr = Mg + 2 C6H5Br + 2 C8H8O

1,1-diphenylethanol moles equal 2.04 10-3 mol of bromobenzene divided by 2 * 1 mol of 1,1-diphenylethanol divided by 2 mol of bromobenzene, which equals 5.10 10-4 mol of 1,1-diphenylethanol.

Therefore, the 1,1-diphenylethanol theoretical yield is:

Theoretical yield is equal to moles of 1,1-diphenylethanol times its molecular weight, which is 5.10 10-4 mol times 198.28 g/mol, or 0.101 g.

c. 0.172 g is listed as the actual yield.

learn more about identify  here:

https://brainly.com/question/15285166

#SPJ11

If a cube of 1 mm side is divided into 1 nm-sized cubes, the total surface area will increase by a factor of 6 x 10⁶, hence C is correct option.

Each face of the original cube has an area of (1 mm)² = 10⁶ nm². When we divide the cube into smaller cubes of 1 nm on each side, we increase the number of faces by a factor of (1 nm / 1 mm)² = 10⁻⁶, since each small cube has six faces. Therefore, the total surface area of the small cubes is:

= 6 x (10⁶ nm²) x (10⁶ x 10⁻⁶)

= 6 x 10⁶ nm².

This is an increase in the total surface area by a factor of 6 x 10⁶.

To know more about surface area of cube, visit,

https://brainly.com/question/28776132

#SPJ4

If iron filings are placed 10 cm away from the magnet, the pattern they form will be different from the pattern formed when they are placed closer to the magnet.

A magnet is a material or object that produces a magnetic field. This field is responsible for the attractive or repulsive force that magnets exhibit towards other magnets, magnetic materials, and electrically charged particles. Magnetic materials, such as iron, cobalt, and nickel, have their electrons arranged in a particular way that creates a magnetic moment or an intrinsic magnetic field.

When these materials are magnetized, their magnetic moments align in the same direction, creating a stronger magnetic field. Magnets are used in a wide range of applications, including motors, generators, magnetic storage devices, and medical imaging machines. They are also used in everyday objects like fridge magnets, compasses, and speakers.

To learn more about Magnet visit here:

brainly.com/question/2841288

#SPJ4

When Isatou drops the plastic bag, it stays the same (option A).

The plastic bag does not melt in the rain or crumble into dust too. It will most likely stay the same for a very long time, as plastic takes hundreds of years to break down naturally when Isatou drops it. However, if the bag is left outside and exposed to rain and sunlight, it may start to degrade and break apart into smaller pieces called microplastics. Eventually, these microplastics can end up in the soil, waterways, and even in our food chain, posing a significant threat to the environment and wildlife. Therefore, it is important to properly dispose of plastic bags and other single-use plastics to prevent environmental harm.

Learn more about plastic: https://brainly.com/question/29915081

#SPJ11

During isokinetic testing at high angular velocities (>240 degrees/sec), the approximate torque capability of eccentric muscle actions is higher than that of concentric muscle actions.

This is because eccentric muscle actions involve the lengthening of the muscle fibers while under tension, which results in a greater amount of force production compared to concentric muscle actions that involve shortening of the muscle fibers. Additionally, during eccentric actions, the muscle fibers can recruit more motor units, leading to a greater force output.
In isokinetic testing, where the speed of the movement is constant, eccentric muscle actions can generate higher torque due to their ability to produce greater force per unit of time. Therefore, athletes who engage in activities that require high levels of eccentric muscle actions, such as running downhill or jumping, may have a greater capacity to generate force at high angular velocities.
Overall, the higher torque capability of eccentric muscle actions during isokinetic testing at high angular velocities may have implications for athletes and rehabilitation programs that aim to improve strength and power output.

Learn more about torque here:

https://brainly.com/question/25708791

#SPJ11

The record for the longest single space flight is Mark Vande Hei. The record of the days was 341 days.

Astronautics is used in spaceflight, which involves launching or navigating a spacecraft into or through space, either with or without people on board. The majority of spaceflight is undertaken without a crew and uses satellite-type spacecraft in orbit around the Earth, but it also uses space probes for missions outside of Earth orbit.

With a 341-day space mission, NASA astronaut Mark Vande Hei beat the previous record set by an American explorer. Since April 2021, he has been residing aboard the International Space Station. In order to learn more about how spaceflight affects the human body, Mark Vande Hei broke the record that another former US astronaut, Scott Kelly, established in the year 2016.

Read more about space flight on:

https://brainly.com/question/924308

#SPJ4

It takes approximately 0.75 seconds for the soot to get all the way through the precipitator tube.


To calculate the time it takes for the soot to get through the precipitator tube, we need to first calculate the distance that the soot needs to travel.

The length of the precipitator is given as 3 meters. Each tube or honeycomb is 25 cm wide, which is equal to 0.25 meters.

Assuming that the soot is traveling through the center of each tube, it needs to travel a distance of 3 meters divided by 0.25 meters per tube, which equals 12 tubes.

So the total distance the soot needs to travel is 12 tubes x 0.25 meters per tube, which equals 3 meters.

Now, we can use the formula: time = distance / speed to calculate the time it takes for the soot to travel through the precipitator.

The distance we calculated is 3 meters, and the speed at which the soot is rising is given as 10 m/s.

Plugging these values into the formula, we get: time = 3 meters / 10 m/s = 0.3 seconds.

Therefore, it takes approximately 0.75 seconds (12 tubes x 0.3 seconds per tube) for the soot to get all the way through the precipitator tube.

To know more about precipitator tube, visit here :

brainly.com/question/31270808

#SPJ11