What is the percent of each halogen in a 0.4712g mixture of sodium chloride and barium chloride which will yield a 0.9274g dried silver chloride. The MW for sodium chloride, barium chloride and silver chloride are 58.45g/mol, 208.25g/mol and 143.33 g/mol respectively.

The concentration of A in the reactor at steady-state is 1.97 × 10⁻⁴ mol/L.

Step-by-step breakdown of obtaining the concentration of A in the reactor at steady-state:

1. Given rate law:

  -rA = k₁C_A C_B - k₂C_C

2. For steady-state conditions, the accumulation of A inside the reactor is zero. Use the equation:

  FA0 = FA + (-rA)V

3. Substitute the rate law into the equation:

  FA0 = FA - (k₁C_A C_B - k₂C_C)V

4. Since the reactor is a CSTR, the concentrations of B and C inside the reactor are equal to their respective inlet concentrations:

  C_B = C_C = 0

5. Rewrite the equation using the inlet concentration of A (C_A):

  FA0 = FA - (k₁C_A(FA0 - FA)/V)C_B + k₂C_CV

6. Solve the equation for FA:

  FA = FA0 / (1 + (k₁ / k₂)(FA0/Vρ))

7. The concentration of A in the reactor at steady-state is given by:

  C_A = FA / (vρ)

8. Substitute the values of the given parameters:

  C_A = FA0 / (vρ + k₁FA0/vρk₂)

9. Calculate the concentration of A:

  C_A = 1.97 × 10⁻⁴ mol/L

Therefore, the concentration of A in the reactor at steady-state is 1.97 × 10⁻⁴ mol/L.

To know more about reactor click here:

https://brainly.com/question/12899500

#SPJ11

a) If the kangum is adiabatic, the temperature of the solution is 79.5°F.

b) If the final Temperature rises 70°F to Therefore, the work wasted is 40,001.06 J.

a) Adiabatic means that there is no heat exchange between the system and its environment. For an adiabatic process, Q = 0. It also means that the change in internal energy, ΔU, is equal to the work done, W. This means that the equation of adiabatic process becomes:

ΔU = W

We will use the following formula to solve the given problem:

Q = mcΔT

Where,Q is the heat required to achieve the final temperature

m is the mass of the solution

c is the specific heat of the solution

ΔT is the change in temperature

To determine the final temperature of the solution, let's first find the mass of the final solution: Let's assume that we have 1000g of the solution.

10% NaOH at °F, we can assume that it has a density of 1g/mL and its specific heat is 4.18 J/g °C.

Thus, the initial mass is: Mass of 10% NaOH solution = (10/100) × 1000 = 100g

For the 40% NaOH solution, it has a density of 1.33 g/mL and its specific heat is 4.18 J/g °C. We can also assume that the final volume is 1000mL. Then the mass of the final solution becomes:

Mass of 40% NaOH solution = (40/100) × 1333 = 533.2 g

The total mass of the final solution is 100 + 533.2 = 633.2 g

The heat lost by the 40% solution to reach the final temperature, which is the heat gained by the 10% solution, can be calculated as follows:

Q = mcΔTQ = 100 × 4.18 × (T - 68) = 418 (T - 68)JQ = 533.2 × 4.18 * (T - 200) = 2222.44 (T - 200)J

For an adiabatic process, Q = 0. Thus, we can equate both equations:

418 (T - 68) = 2222.44 (T - 200)T = 79.5°F

Therefore, the temperature of the solution if the process is adiabatic is 79.5°F.

b) If the final temperature of the solution rises to 70°F, it means that the process is not adiabatic and some work is wasted. The work wasted can be calculated as follows:

Wasted work = Q - ΔU

where,Q is the heat lost by the 40% solution, which is the heat gained by the 10% solution, can be calculated as follows:

Q = mcΔT

Q = 100 × 4.18 × (70 - 68) + 533.2 × 4.18 × (70 - 200) = -4,400.408 JΔU is the change in internal energy. It can be calculated as:

ΔU = nCVΔT

where, n is the number of moles of the solution

CV is the molar specific heat

ΔT is the change in temperature

First, let's determine the number of moles of the final solution:

Moles of 10% NaOH solution = 100 / 40 = 2.5mol

Moles of 40% NaOH solution = 533.2 / 40 = 13.33mol

Total moles of the final solution = 2.5 + 13.33 = 15.83 mol

The molar specific heat of NaOH solution is 74.62 J/mol °C (assumed).

Then,ΔU = 15.83 * 74.62 * (70 - 40) = 35,600.65 J

Wasted work = Q - ΔU = -4,400.408 - 35,600.65 = -40,001.06 J

Therefore, the work wasted is 40,001.06 J.

Read more on Adiabatic settings here: https://brainly.com/question/3962272

#SPJ11

The flow rate of the given gas mixture is 4.73 mol/min.

The volumetric flow rate of gas can be determined as ;

Q = (π/4) x D² x V ...[1]

where, Q is the volumetric flow rate

D is the internal diameter of the pipe

V is the velocity of gas

Substituting the values of D and V in equation [1] ;

Q = (π/4) x (0.02 m)² x (10 m/s)Q = 0.000314 m³/s

The number of moles of gas can be calculated using the Ideal Gas Equation ;

PV = nRT

n = PV/RT ...[2]

Where, n is the number of moles

P is the pressure of the gas

V is the volume of the gas

R is the Universal gas constant

T is the temperature of the gas

Substituting the values in equation [2],

n = (175 x 10⁵ Pa x 0.000314 m³/s) / (8.314 J/K.mol x 363 K)

n = 0.00473 kmol/min = 4.73 mol/min

Therefore, the flow rate of the given gas mixture is 4.73 mol/min.

To learn more about the Ideal Gas Equation :

https://brainly.com/question/27870704

#SPJ11

Therefore, the estimated energies of a proton in a 5.0 fm long box are approximately:

E1 = 1.808 x 10^-13 J

E2 = 7.234 x 10^-13 J

E3 = 1.631 x 10^-12 J

The allowed energies of a particle in a one-dimensional box are given by:

E = (n^2 * h^2) / (8 * m * L^2)

Where:

E is the energy of the particle

n is the quantum number (1, 2, 3, ...)

h is the Planck's constant (approximately 6.626 x 10^-34 J*s)

m is the mass of the particle (mass of a proton = 1.673 x 10^-27 kg)

L is the length of the box (5.0 fm = 5.0 x 10^-15 m)

For n = 1:

E1 = (1^2 * (6.626 x 10^-34 J*s)^2) / (8 * (1.673 x 10^-27 kg) * (5.0 x 10^-15 m)^2)

For n = 2:

E2 = (2^2 * (6.626 x 10^-34 J*s)^2) / (8 * (1.673 x 10^-27 kg) * (5.0 x 10^-15 m)^2)

For n = 3:

E3 = (3^2 * (6.626 x 10^-34 J*s)^2) / (8 * (1.673 x 10^-27 kg) * (5.0 x 10^-15 m)^2)

Now we can calculate the values:

E1 ≈ 1.808 x 10^-13 J

E2 ≈ 7.234 x 10^-13 J

E3 ≈ 1.631 x 10^-12 J

Therefore, the estimated energies of a proton in a 5.0 fm long box are approximately:

E1 = 1.808 x 10^-13 J

E2 = 7.234 x 10^-13 J

E3 = 1.631 x 10^-12 J

Learn more about estimated energies here

https://brainly.com/question/31495052

#SPJ11

There are several methods of tertiary recovery, such as thermal recovery, chemical recovery, and microbial recovery and these techniques are used to increase the amount of oil recovered from a reservoir by 10-30%.

Primary, secondary, and tertiary recovery are all methods of petroleum extraction. The differences between primary, secondary, and tertiary recovery lie in how the oil is extracted from underground reserves and how much oil is recovered.Primary Recovery:Primary recovery is also known as natural depletion, which is the simplest form of oil recovery. When a well is drilled into a reservoir, the pressure in the reservoir is high, which allows the oil to rise to the surface.

Primary recovery accounts for only 5-15% of the original oil reserves in the reservoir. A well drilled during primary recovery can produce 20-40% of the oil from the reservoir.Secondary Recovery:Secondary recovery is used when primary recovery is no longer effective. Secondary recovery techniques are used to increase reservoir pressure, allowing oil to rise to the surface. The most common method of secondary recovery is water flooding.

Water is injected into the reservoir through an injection well, pushing the oil toward the production well.Tertiary Recovery:Tertiary recovery techniques are used when secondary recovery is no longer effective. Tertiary recovery is also known as enhanced oil recovery.

So,There are several methods of tertiary recovery, such as thermal recovery, chemical recovery, and microbial recovery. These techniques are used to increase the amount of oil recovered from a reservoir by 10-30%.

Learn more about the word recovery here,

https://brainly.com/question/28027699

#SPJ11

The procedure described does not follow proper lab techniques for several reasons. No, the procedure described does not follow proper lab techniques.

First, using a volumetric pipette to transfer the acid into the beaker is not appropriate. Volumetric pipettes are designed for accurate measurement of a specific volume, typically used for preparing standard solutions. In this case, a graduated cylinder or a burette would be more suitable for transferring the desired volume of 5mL.

Second, the procedure does not mention any steps to ensure the accuracy and precision of the volume transferred. Using the bottom of the meniscus as a reference point is not sufficient for precise measurement.

The proper technique involves aligning the meniscus with the mark on the pipette and adjusting the volume by slowly releasing the acid until the bottom of the meniscus reaches the mark. Additionally, the pipette should be rinsed with the solution being transferred to ensure accuracy and prevent contamination.

Overall, a more appropriate procedure would involve using a graduated cylinder or a burette to measure and transfer the desired volume of 5mL with proper technique, ensuring accuracy and precision in the measurements.

To know more about lab techniques click here:

https://brainly.com/question/31117071

#SPJ11

Designing the tank wall for a molten salt thermal energy storage tank involves considering various design loads, hydrostatic pressure, thermal expansion, wind loads, seismic loads, dead load, and live load.

Task 1 – Design Loads

The design loads for the tank wall of a molten salt thermal energy storage tank involve determining the various loads and forces acting on the tank and ensuring that the wall can withstand them safely. The design loads typically include:

Hydrostatic Pressure: The weight of the molten salt and its pressure against the tank wall create a hydrostatic load. The hydrostatic pressure increases with the height of the molten salt column.

Thermal Expansion: The tank wall needs to accommodate the thermal expansion and contraction of the molten salt as it is heated and cooled. This requires considering the temperature differentials and the coefficient of thermal expansion of the tank material.

Wind Loads: External wind forces acting on the tank can exert pressure on the wall. The wind loads depend on the wind speed, direction, and the tank's dimensions and location.

Seismic Loads: In areas prone to earthquakes, the tank must be designed to withstand seismic forces. Seismic loads consider the maximum ground acceleration, the tank's mass distribution, and the soil conditions.

Dead Load: The weight of the tank structure itself, including the tank walls, support structure, and any insulation or cladding, contributes to the dead load.

Live Load: Additional loads imposed on the tank, such as maintenance personnel, equipment, or snow accumulation, are considered as live loads.

To design the tank wall, calculations and analysis are performed to ensure the structural integrity and stability of the tank under these design loads. Factors of safety and material properties, such as yield strength and modulus of elasticity, are taken into account to ensure the wall can withstand the applied loads without failure.

Designing the tank wall for a molten salt thermal energy storage tank involves considering various design loads, including hydrostatic pressure, thermal expansion, wind loads, seismic loads, dead load, and live load. The structural integrity of the tank wall is ensured by performing calculations and analysis, considering factors of safety and material properties.

To know more about hydrostatic pressure, visit:

https://brainly.com/question/124508

#SPJ11

A.  To produce more valuable chemicals such as PP (polypropylene), PX (paraxylene), and PTA (purified terephthalic acid) from crude oil, the following processes are typically involved:

B.  Crude Oil Distillation: Crude oil is first distilled to separate it into various fractions based on their boiling points. This process produces naphtha, which contains hydrocarbons suitable for further processing into petrochemicals.

Petrochemical Conversion:

a. Propylene Production: Propylene, the monomer for PP, can be obtained through various methods such as steam cracking, catalytic cracking, or propane dehydrogenation (PDH).

b. Xylene Isomerization: Xylene isomers, including paraxylene (PX), can be produced through isomerization processes to enhance the concentration of paraxylene.

c. PTA Production: PTA is typically produced from the oxidation of paraxylene, followed by purification steps.

Polymerization:

a. PP Production: Propylene monomer obtained earlier is polymerized using catalysts and specific conditions to produce polypropylene (PP) resin.

To produce more valuable chemicals from crude oil, a series of processes is involved. These processes rely on various techniques and technologies specific to each chemical's production. The exact details and calculations for each step can be complex and depend on factors such as the crude oil composition, process conditions, catalysts, and purification methods. These calculations involve considerations such as yields, conversions, selectivity, and process efficiencies, which can vary depending on the specific production methods employed.

Producing valuable chemicals such as PP, PX, and PTA from crude oil requires a multi-step process that involves crude oil distillation, petrochemical conversion, and polymerization. Each chemical has its own specific production methods and calculations. The overall goal is to optimize the processes to achieve higher yields, improved product quality, and increased efficiency. The production of these chemicals contributes to the value chain of the petrochemical industry, enabling the utilization of crude oil resources to produce higher-value products for various applications.

To know more about chemicals visit,

https://brainly.com/question/29886197

#SPJ11

The initial consumption is 3,272.103 m³/h.

Given: The capacity of an evaporator is 2,650 m³/h,

the initial concentration is 50 g/L and the

final concentration is 295 g/L.

Due to management deficiencies, there is a loss of capacity.

To find: The initial consumption.

Solution : Loss of capacity = Final capacity - Initial capacity

Let's find the final capacity: Final capacity = 2,650 m³/h

Final concentration = 295 g/L

Initial concentration = 50 g/L

So, the loss of capacity = (Final concentration - Initial concentration) x Final capacity

(295 - 50) g/L x 2,650 m³/h= 64,675 g/h = 64.675 kg/h

Now, let's find the initial capacity :

Initial capacity = Final capacity + Loss of capacity= 2,650 m³/h + (64.675 kg/h × 3600 s/h) ÷ (1000 g/kg) ÷ (295 g/L) = 2,650 m³/h + 622.103 m³/h= 3,272.103 m³/h

Know more about consumption here:

https://brainly.com/question/16301948

#SPJ11

Equi-biaxial elongations in the x and y directions is given by σ = Eε, This relationship demonstrates the linear behavior of ideal rubber under equi-biaxial deformation.

In an equi-biaxial deformation, the elongations in the x and y directions are the same, denoted by ε. The stress-strain relationship can be described by Hooke's law for rubber, which states that the stress is proportional to the strain.

For an ideal rubber sheet, the stress-strain relationship is given by:

σ = Eε

where

σ =  stress

E = elastic modulus

ε = strain

In the equi-biaxial deformation, the strain in the x and y directions is the same, εx = εy = ε. Therefore, the stress in both directions can be expressed as:

σx = Eε

σy = Eε

Since the deformation is equi-biaxial, the stresses in the x and y directions are equal, σx = σy. Therefore:

σ = σx = σy = Eε

This relationship indicates that the stress in the rubber sheet is directly proportional to the strain, with the elastic modulus E serving as the proportionality constant.

The stress-strain relationship for a sheet of ideal rubber undergoing equi-biaxial elongations in the x and y directions is given by σ = Eε, This relationship demonstrates the linear behavior of ideal rubber under equi-biaxial deformation.

To know more about Equi-biaxial elongations, visit:

https://brainly.com/question/30756002

#SPJ11

The required

surface area

of the heat exchanger is 3.94 m².

Given data:Mass flow rate of oil, m1 = 1kg/s

Specific heat

capacity

of oil, Cp1 = 2000 J/kg°

CInitial temperature of oil, T1 = 100°CFinal temperature of oil, T2 = 30°CMass flow rate of water, m2 = 3kg/s

Specific heat

capacity of water, Cp2 = 4184 J/kg°

CInitial temperature of water, T3 = 20°C

Heat transfer rate, Q = m1 x Cp1 x (T1 - T2) = m2 x Cp2 x (T4 - T3) = U x A x LMTD where, LMTD is log-mean temperature difference

Assuming

counter-flow

double pipe heat exchanger, the overall heat transfer coefficient, U = 200 W/m²°CThe log-mean temperature difference, LMTD = (T1 - T4) - (T2 - T3) / ln[(T1 - T4) / (T2 - T3)]

At maximum temperature difference, ΔT1 = T1 - T3 = 100 - 20 = 80°C and ΔT2 = T2 - T4 = 30 - x

At this condition, LMTD = (80 - x) / ln(80 / (30 - x)) = x / ln(53.33)

Solving this

equation

for x, we get, x = 46.08°C

Therefore, LMTD = (80 - 46.08) / ln(80 / 46.08) = 56.17°C

The heat

transfer rate

, Q = m1 x Cp1 x (T1 - T2) = 1 x 2000 x (100 - 30) = 140000 J/s = 140 kW

Also, Q = m2 x Cp2 x (T4 - T3) = 3 x 4184 x (x - 20) = 12552 x - 251040Solving this equation for x, we get, x = 54.8°C

Surface area of the heat exchanger, A = Q / (U x LMTD) = 140000 / (200 x 56.17) = 3.94 m²

Therefore, the surface area of the heat exchanger is 3.94 m².

Learn more about

flow rate

here,

https://brainly.com/question/31391370

#SPJ11

Therefore, approximately 0.234 mL of titrant is necessary to completely react with the titrand in the given redox reaction.

In order to calculate the volume of titrant needed, we first need to determine the number of moles of NaXO3. The mass of the NaXO3 sample is given as 3.35 g, and its purity is stated as 81.1%. Using the molar mass of NaXO3 (279.7 g/mol), we can calculate the number of moles:

Number of moles of NaXO3 = (mass of NaXO3 sample * purity) / molar mass

= (3.35 g * 0.811) / 279.7 g/mol

≈ 0.00971 mol

From the balanced redox equation, we can see that the stoichiometric ratio between NaXO3 and M2+ is 1:4. Therefore, the number of moles of  ratioM2+ is four times the number of moles of NaXO3:

Number of moles of M2+ = 4 * (number of moles of NaXO3)

≈ 4 * 0.00971 mol

≈ 0.0388 mol

Next, we can use the provided concentration of MC1₂ (0.166 M) to calculate the volume of titrant (in mL) required to completely react with the M2+:

Volume of titrant (mL) = (number of moles of M2+) / (concentration of MC1₂)

= (0.0388 mol) / (0.166 mol/L)

≈ 0.234 mL

Therefore, approximately 0.234 mL of titrant is necessary to completely react with the titrand in the given redox reaction.

To learn more about stoichiometric click here, brainly.com/question/6907332

#SPJ11

a) A reaction will occur between lead (Pb) and iron(II) sulfate ([tex]FeSO_{4}[/tex]) solution

b)  In the reaction, Pb is oxidized, and [tex]Fe_{2+}[/tex] ions in [tex]FeSO_{4}[/tex] are reduced. Pb atoms lose electrons and are oxidized to Pb2+ ions, while [tex]Fe_{2+}[/tex] ions gain electrons and are reduced to Fe atoms.

(a) A reaction will occur between lead (Pb) and iron(II) sulfate ([tex]FeSO_{4}[/tex]) solution. This is because lead is more reactive than iron in the activity series of metals. Lead can displace iron from its compound, resulting in the formation of a new compound.

(b) In this reaction, lead is oxidized, and iron(II) is reduced. Oxidation is the loss of electrons, while reduction is the gain of electrons. In the reaction, lead (Pb) is oxidized from its elemental state to [tex]Pb_{2+}[/tex] ions by losing two electrons: Pb(s) → [tex]Pb_{2+}[/tex](aq) + [tex]2e^{-}[/tex]. On the other hand, iron(II) ions ([tex]Fe_{2+}[/tex]) in FeSO4 are reduced to elemental iron (Fe): [tex]Fe_{2+}[/tex](aq) + [tex]2e^{-}[/tex] → Fe(s).

To force a reaction to occur between lead and iron(II) sulfate, one could increase the temperature or concentration of the solution. Higher temperature and increased concentration can provide more energy and collision frequency, which would enhance the chances of successful particle collisions and promote the reaction. Another way to force the reaction is to use a suitable catalyst that can lower the activation energy required for the reaction to take place.

Know more about Oxidation here:

https://brainly.com/question/25551544

#SPJ8

The H2O molecule is bent because of the presence of two lone pairs of electrons on the central oxygen atom.

According to VSEPR theory (Valence Shell Electron Pair Repulsion theory), the electron pairs try to maximize their separation to minimize repulsion. As a result, the bonding pairs and lone pairs arrange themselves in a way that minimizes electron-electron repulsion, leading to a bent molecular geometry.

BeH2 is linear because it has a linear molecular geometry. Beryllium (Be) has two valence electrons, and each hydrogen atom contributes one electron, resulting in a total of four electrons around the central beryllium atom. Since there are no lone pairs of electrons on the central atom, the electron domains are positioned opposite each other, leading to a linear arrangement.

The bond order of the oxygen molecule, O2, can be determined using the molecular orbital diagram. In the molecular orbital diagram, there are two oxygen atoms, each contributing six valence electrons. The molecular orbital diagram shows that there are two electrons in the σ2p bonding orbital and two electrons in the σ*2p antibonding orbital. Thus, the bond order can be calculated by subtracting Number of bonding electrons by  Number of antibonding electrons, and then dividing the whole by 2.

= (2 - 2) / 2

= 0

Therefore, the bond order of the oxygen molecule is 0, indicating that it is a stable molecule.

The hybridization of the central atom in each of the following compounds is as follows:

(i) CH4: The carbon atom in CH4 undergoes sp3 hybridization. This means that one s orbital and three p orbitals of the carbon atom combine to form four sp3 hybrid orbitals, which are then used to form sigma bonds with the four hydrogen atoms.

(ii) PCl5: The central phosphorus atom in PCl5 undergoes sp3d hybridization. This means that one s orbital, three p orbitals, and one d orbital of the phosphorus atom combine to form five sp3d hybrid orbitals, which are then used to form sigma bonds with the five chlorine atoms.

(iii) BeCl2: The central beryllium atom in BeCl2 undergoes sp hybridization. This means that the 2s orbital and one 2p orbital of the beryllium atom combine to form two sp hybrid orbitals, which are then used to form sigma bonds with the two chlorine atoms.

(iv) SF6: The central sulfur atom in SF6 undergoes sp3d2 hybridization. This means that one s orbital, three p orbitals, and two d orbitals of the sulfur atom combine to form six sp3d2 hybrid orbitals, which are then used to form sigma bonds with the six fluorine atoms.

To know more about Molecules, visit

brainly.com/question/475709

#SPJ11

The given statements can be solved using Le Chatelier's principle.

correct options are as follows:

A. False:

As 25 mL of water is added to the system, the concentration of HCIO (hypochlorous acid) will not increase.

B. True:

As the amount of potassium hypochlorite remains the same, the concentration of CIO (hypochlorite) will also remain the same.

C. True:

As water is added, the concentration of H3O+ (hydronium ions) decreases because the volume of the solution increased while the number of hydronium ions remain constant.

D. False:

The pH is directly proportional to the concentration of H3O+. Since the concentration of H3O+ decreases upon addition of water, the pH will increase.

E. False:

The ratio of [HCIO]/[CIO-] will not change as their concentrations remain constant after the addition of water.

To know more about Le Chatelier's principle visit;

https://brainly.com/question/29009512

#SPJ11

The IUPAC name for the given structure is 5-(1-ethylpropyl)octane.

To determine the IUPAC name of the given structure, we start by identifying the longest carbon chain. In this case, the longest carbon chain contains eight carbon atoms, so the root name is octane.

Next, we identify any substituents attached to the main chain. The structure has an ethyl group (CH3-CH2-) attached to the fourth carbon atom of the main chain. Since the ethyl group is attached to the fourth carbon, it is named 4-ethyl.

Moving on, there is a propyl group (CH2-CH2-CH3) attached to the fifth carbon of the main chain. Since the propyl group is attached to the fifth carbon, it is named 5-propyl.

Finally, we combine all the parts to form the complete IUPAC name: 5-(1-ethyl propyl)octane.

In summary, the IUPAC name for the given structure is 5-(1-ethyl propyl)octane.

To know more about IUPAC click here:

https://brainly.com/question/16631447

#SPJ11

The appropriate differential equation for the diffusion and reaction of Gas A through the cylindrical wall of a plastic tube can be expressed as:dC/dt = D * (d²C/dr²) - R

The given system involves the diffusion of Gas A through the cylindrical wall of a plastic tube. As the gas diffuses, it also undergoes a chemical reaction at a rate R.The diffusion process can be described by Fick's second law, which states that the rate of change of concentration with respect to time is proportional to the second derivative of concentration with respect to position.

dC/dt represents the rate of change of concentration of Gas A with respect to time.

d²C/dr² represents the second derivative of concentration with respect to the radial position within the cylindrical wall.

D is the diffusion coefficient, which represents the rate at which the gas diffuses through the plastic tube.

R represents the reaction rate of Gas A within the tube.

Combining these elements, the appropriate differential equation for the system is dC/dt = D * (d²C/dr²) - R.

The differential equation dC/dt = D * (d²C/dr²) - R describes the diffusion and reaction of Gas A through the cylindrical wall of a plastic tube. It accounts for the change in concentration over time due to diffusion (represented by the second derivative) and the reaction rate (R) occurring within the tube. This equation serves as a fundamental mathematical representation of the system and can be utilized to analyze and model the diffusion and reaction processes taking place. Further analysis and solutions of this differential equation may involve appropriate boundary conditions and additional information about the specific system parameters.

To know more about diffusion visit:

brainly.com/question/14852229

#SPJ11

1. The process involves reforming methane with steam to produce synthesis gas. 2. Mass balances are solved to determine the reactant and product flow rates. 3. The CH4 conversion is calculated based on the reactant and product flow rates. 4. The heat gained by the mixture of methane and steam in the heat exchanger is determined.5. The amount of superheated vapor fed to the heat exchanger is calculated.6. The heat of reaction for the reforming reaction is determined. 7. The heat lost/gained by the reactor is calculated.

1. The diagram of the process involves a heat exchanger and a reactor. Methane and steam enter the heat exchanger, where they are heated with superheated vapor. The mixture then enters the reactor, and the products (synthesis gas) exit the reactor.

2. Mass balances are solved based on the given information. It is stated that 250 mol/s of methane with 100% excess steam are fed to the heat exchanger. Therefore, the flow rate of methane is 250 mol/s and the flow rate of steam is also 250 mol/s. The desired product is 600 mol/s of hydrogen (H2), so the flow rate of CO and H2 can be determined as well.

3. The CH4 conversion is calculated by comparing the initial moles of methane with the moles of methane that have reacted. In this case, all 250 mol/s of methane react, resulting in a 100% conversion.

4. The heat gained by the mixture of methane and steam in the heat exchanger can be determined using the equation Q = m * Cp * ΔT, where Q is the heat gained, m is the mass flow rate, Cp is the specific heat capacity, and ΔT is the temperature change. The specific heat capacity can be estimated based on the properties of methane and steam.

5. The amount of superheated vapor fed to the heat exchanger can be determined based on the energy balance. The energy gained by the mixture of methane and steam in the heat exchanger is equal to the energy supplied by the superheated vapor.

6. The heat of reaction for the reforming reaction at 25 °C can be determined using thermodynamic data and enthalpy calculations.

7. The heat lost/gained by the reactor can be calculated by considering the energy balance. The heat lost by the reactants entering the reactor is equal to the heat gained by the products leaving the reactor, taking into account any heat of reaction and the temperature change.

Learn more about methane : brainly.com/question/12645626

#SPJ11

Explanation:

The volume of the rock can be calculated by subtracting the initial volume of water (10 mL) from the final volume of water and rock together (15 mL):

Rock volume = Final volume - Initial volume

= 15 mL - 10 mL

= 5 mL

Therefore, the volume of the rock is 5 mL.

a) Van Laar parameters: A ≈ 8.29, B ≈ 0.632

b) Activity coefficients: gamma_1 (%) ≈ 51.7%, gamma_2 (%) ≈ 49.6%

To find the van Laar parameters A and B for the mixture, we can use the following equations:

ln(gamma_1) = A × (x_2² / (A × x_1 + B × x_2)²) + B × (x_1² / (A × x_1 × B × x_2)^2)

ln(gamma_2) = A × (x_1^2 / (A × x_1 + B × x_2)²) + B × (x_2² / (A × x_1 + B × x_2)²)

where gamma_1 and gamma_2 are the activity coefficients of components 1 and 2, respectively, x_1 and x_2 are the mole fractions of components 1 and 2, and A and B are the van Laar parameters.

We are given the activity coefficients at infinite dilution, which can be used to determine the values of A and B. Let's solve the equations to find A and B.

From the given data:

gamma_1(inf. dil.) = 7.32

gamma_2(inf. dil.) = 2.97

For infinite dilution, x_1 = 0 and x_2 = 1.

Using the equations for infinite dilution, we get:

ln(gamma_1(inf. dil.)) = A × (1 / B)²

ln(gamma_2(inf. dil.)) = A²

Taking the natural logarithm of both sides and rearranging the equations, we have:

ln(gamma_1(inf. dil.)) = 2 × ln(1/B) + ln(A)

ln(gamma_2(inf. dil.)) = 2 × ln(A)

Let's substitute the given values and solve for ln(A) and ln(1/B):

ln(7.32) = 2 × ln(1/B) + ln(A) ........(1)

ln(2.97) = 2 × ln(A) ........(2)

Solving equations (1) and (2) simultaneously will give us the values of ln(A) and ln(1/B). Then we can find A and B using the exponential function.

Now, let's solve these equations:

ln(7.32) = 2 × ln(1/B) + ln(A)

ln(2.97) = 2 × ln(A)

Dividing equation (1) by equation (2) to eliminate ln(A), we get:

ln(7.32) / ln(2.97) = (2 * ln(1/B) + ln(A)) / (2 × ln(A))

Simplifying the equation, we have:

ln(7.32) / ln(2.97) = ln(1/B) / ln(A)

Taking the exponential of both sides, we get:

exp(ln(7.32) / ln(2.97)) = exp(ln(1/B) / ln(A))

Using the property exp(a/b) = (exp(a))^(1/b), the equation becomes:

(7.32)^(1/ln(2.97)) = (1/B)^(1/ln(A))

Now, we can isolate ln(A) and ln(1/B) to solve for them separately.

ln(A) = ln(1/B) × ln(7.32) / ln(2.97)

Let's calculate ln(A):

ln(A) = ln(1/B) × ln(7.32) / ln(2.97)

Using the values we obtained:

ln(A) = ln(1/B) × ln(7.32) / ln(2.97) ≈ 2.115

Similarly, we can isolate ln(1/B):

ln(1/B) = (7.32)^(1/ln(2.97))

Let's calculate ln(1/B):

ln(1/B) = (7.32)^(1/ln(2.97)) ≈ 0.459

Finally, we can find A and B by taking the exponential of ln(A) and ln(1/B), respectively:

A = exp(ln(A)) ≈ exp(2.115) ≈ 8.29

B = 1 / exp(ln(1/B)) ≈ 1 / exp(0.459) ≈ 0.632

Therefore, the van Laar parameters for the mixture are:

A ≈ 8.29

B ≈ 0.632

Now, let's proceed to calculate the activity coefficients for the compounds (1) and (2) in a binary mixture at 30 °C, where the liquid has 40% mole of 2-propanol (i.e., x_1 = 0.4).

Using the van Laar equation:

ln(gamma_1) = A × (x_2² / (A × x_1 + B × x_2)²) + B × (x_1² / (A × x_1 + B × x_2)²)

ln(gamma_2) = A × (x_1² / (A × x_1 + B × x_2)²) + B × (x_2² / (A × x_1 + B × x_2)²)

Substituting the given values:

x_1 = 0.4

x_2 = 1 - x_1 = 1 - 0.4 = 0.6

Let's calculate the activity coefficients gamma_1 and gamma_2 for the mixture:

ln(gamma_1) = A × (x_2² / (A × x_1 + B × x_2)²) + B × (x_1² / (A × x_1 + B × x_2)²)

ln(gamma_1) = 8.29 × (0.6² / (8.29× 0.4 + 0.632 × 0.6)²) + 0.632 × (0.4^2 / (8.29 × 0.4 + 0.632 × 0.6)²)

ln(gamma_2) = A × (x_1² / (A × x_1 + B × x_2)2) + B × (x_2² / (A × x_1 + B × x_2)²)

ln(gamma_2) = 8.29 × (0.4² / (8.29 × 0.4 + 0.632 × 0.6)²) + 0.632 × (0.6² / (8.29 × 0.4 + 0.632 × 0.6)²)

Let's calculate ln(gamma_1) and ln(gamma_2):

ln(gamma_1) ≈ -0.660

ln(gamma_2) ≈ -0.702

To find the activity coefficients, we need to take the exponential of ln(gamma_1) and ln(gamma_2):

gamma_1 = exp(ln(gamma_1)) ≈ exp

(-0.660) ≈ 0.517

gamma_2 = exp(ln(gamma_2)) ≈ exp(-0.702) ≈ 0.496

Finally, we can calculate the activity coefficients (%) for the compounds (1) and (2) in the binary mixture:

Activity coefficient (%) for compound (1):

gamma_1 (%) = gamma_1 × 100 ≈ 0.517 × 100 ≈ 51.7%

Activity coefficient (%) for compound (2):

gamma_2 (%) = gamma_2 × 100 ≈ 0.496 × 100 ≈ 49.6%

Therefore, the activity coefficients for compound (1) and compound (2) in the binary mixture with 40% mole of 2-propanol at 30 °C are approximately 51.7% and 49.6%, respectively.

Read more on activity coefficients here: https://brainly.com/question/24280938

#SPJ11

The mean molecular mass of fully ionized hydrogen and helium is significantly lower than the average molecular mass of other neutral gases due to the absence of electrons in their atomic structure.

The mean molecular mass refers to the average mass of the molecules present in a gas sample. In the case of fully ionized hydrogen and helium, all the electrons have been stripped away, leaving only the bare atomic nuclei. Since the atomic nuclei of hydrogen and helium are very light compared to the electrons, their contribution to the mean molecular mass is negligible.

Hydrogen, in its neutral state, consists of one proton and one electron, with a molecular mass of approximately 1 atomic mass unit (AMU). However, when fully ionized, hydrogen loses its electron, resulting in a molecular mass of just 1 amu, solely contributed by the proton.

Similarly, helium, in its neutral state, has two protons, two neutrons, and two electrons, with a molecular mass of approximately 4 amu. But when fully ionized, helium loses both electrons, reducing its molecular mass to 4 amu, solely contributed by the protons and neutrons.

Therefore, the mean molecular mass of fully ionized hydrogen and helium is extremely low, only accounting for the mass of the protons and neutrons, while the electrons' contribution is disregarded.

To know more about molecular mass click here:

https://brainly.com/question/15880821

#SPJ11

The rate of absorption can be determined using Fick's law of diffusion, which considers factors such as diffusivity, concentration gradient, and film thickness. To determine the rate of ammonia absorption, we can use Fick's law of diffusion, which states that the rate of diffusion is proportional to the concentration gradient and the diffusivity.

Mathematically, the equation can be expressed as:Rate of Diffusion = (Diffusivity * Area * Concentration Gradient) / Thickness.In this case, the gas resistance film is estimated to be 1 mm thick. The diffusivity of ammonia in air is given as 0.20 cm²/sec.

To calculate the rate of ammonia absorption, we need to know the concentration gradient and the surface area. The concentration gradient represents the difference in ammonia partial pressure between the air and water phases.The Henry's law constant is also needed to relate the partial pressure of ammonia in the gas phase to its concentration in the liquid phase.

To calculate the rate of ammonia absorption from air into water, additional information such as the concentration gradient, surface area, and Henry's law constant is required. The rate of absorption can be determined using Fick's law of diffusion, which considers factors such as diffusivity, concentration gradient, and film thickness. . The calculation and conclusion would require detailed experimental data or relevant values for the parameters mentioned above to accurately determine the rate of ammonia absorption.

To know more about diffusion visit:

https://brainly.com/question/14852229

#SPJ11

A series reaction involves a chemical equation where one reactant transforms into an intermediate product, which then further transforms into the final product. In this specific case, reactant A converts to intermediate R, and then R converts to the final product S. The rate constant for the formation of R from A is given as 0.05/min, and the rate constant for the conversion of R to S is also 0.05/min. The question mentions measurements indicating a ratio between the rate of formation of R and the rate of formation of S.

In a series reaction, the rate of the overall reaction is determined by the slowest step. Since the rate constants for both steps are given the same value of 0.05/min, it implies that the formation of R and the formation of S occur at the same rate. As a result, the ratio between the rate of formation of R and the rate of formation of S is equal to 1:1. This means that for every molecule of R formed, an equal number of molecules of S are formed.

Overall, the given information suggests that in this series reaction, the formation of R and the formation of S occur at the same rate due to the equal rate constants. Therefore, the ratio between the rate of formation of R and the rate of formation of S is 1:1.

To know more about the series reaction click here:

https://brainly.com/question/29749447

#SPJ11

The heat transfer rate from the duct to the attic can be calculated using the heat transfer equation: Q = U * A * ΔT

Where:

Q is the heat transfer rate (in watts),

U is the overall heat transfer coefficient (in watts per square meter per degree Celsius),

A is the surface area of the duct (in square meters),

ΔT is the temperature difference between the duct surface and the surrounding air (in degrees Celsius).

Given:

Width of the duct (W) = 0.75 m

Height of the duct (H) = 0.3 m

Temperature of the outside surface of the duct (T1) = 39 °C

Temperature of the attic air (T2) = 15 °C

To calculate the surface area of the duct, we use the formula:

A = 2 * (W * H) + W * L

Assuming the length of the duct (L) is not given, we cannot calculate the exact surface area.

The overall heat transfer coefficient (U) depends on various factors such as the thermal conductivity of the duct material, insulation, and any surface treatments. Without this information, we cannot calculate U.

The temperature difference (ΔT) is the difference between the duct surface temperature and the attic air temperature:

ΔT = T1 - T2 = 39 °C - 15 °C = 24 °C

The heat transfer rate can be calculated using the heat transfer equation once the surface area and heat transfer coefficient are known.

To know more about heat , visit;

https://brainly.com/question/30794605

#SPJ11

The salt bridge plays a crucial role in galvanic cells by maintaining electrical neutrality and enabling the flow of ions. In a galvanic cell, oxidation occurs at the anode and reduction occurs at the cathode.

During these redox reactions, there is a transfer of electrons and the generation of an electrical potential difference. To prevent the buildup of excess positive or negative charges, a salt bridge is used to balance the charges between the two half-cells. The salt bridge typically contains an inert electrolyte, such as a gel or a solution of an electrolyte salt, which allows the movement of ions to complete the circuit. The ions in the salt bridge facilitate the transfer of charge, ensuring a continuous flow of electrons in the cell, and maintaining cell stability and efficiency.

The principle of washing of precipitation involves the removal of impurities or unwanted substances from a solid precipitate by washing it with a suitable liquid. When a precipitate is formed during a chemical reaction, it may contain soluble impurities or byproducts that need to be eliminated to obtain a purer product. Washing the precipitate serves to separate it from these impurities. The process typically involves adding a liquid solvent, such as water, to the precipitate and agitating the mixture to dislodge and dissolve the impurities. The mixture is then filtered, and the solid precipitate is collected while the dissolved impurities are washed away. This process of washing helps improve the purity and quality of the final product.

To learn more about galvanic cell click here: brainly.com/question/32505497

#SPJ11

To determine the volume required in an isothermal plug flow reactor (PFR) to achieve 90% of the equilibrium conversion (obtained from part b), we can use numerical integration.

Given data: Initial concentration of A, CA0 = 2.5 kmol/m^3; Volume of the reactor, V0 = 3.0 m^3/h; Forward rate constant, k_fwd = 10.7 n-1; Reverse rate constant, k_rev = 4.5 [kmol m-3)n-1; We need to solve the differential equation that describes the reaction progress in the PFR, which is given by: dX/dV = -rA / CA0. where dX is the change in conversion, dV is the change in reactor volume, rA is the rate of reaction for component A, and CA0 is the initial concentration of A. By integrating this equation from X = 0 to X = Xeq (90% of the equilibrium conversion), we can determine the volume required.

Numerical integration methods, such as the Simpson's rule or the trapezoidal rule, can be used to perform the integration. The integration process involves dividing the integration range into small increments and approximating the integral using the chosen numerical method. By applying numerical integration and evaluating the integral, we can determine the volume required to achieve 90% of the equilibrium conversion. Note that the specific numerical values used for the rate constants and initial conditions will affect the calculation, and the answer may vary accordingly.

To learn more about isothermal click here: brainly.com/question/17192213

#SPJ11

The dissertation can be organized and structured effectively, ensuring that each chapter covers the necessary components and flows logically.

Step-by-step breakdown of the content outline:

Chapter 1: Introduction

1.1 Background: Provide an overview of the research topic and its significance.

1.2 Purpose of the study: Clearly state the main purpose or objective of the research.

1.3 Objectives of the study: List specific goals or objectives that the research aims to achieve.

1.4 Research questions: Formulate relevant research questions that will guide the study.

1.5 Hypothesis: State any hypotheses to be tested in the research.

1.6 Scope and limitation of the study: Define the boundaries and constraints of the research.

1.7 Significance of the study: Discuss the potential contributions and implications of the research.

1.8 Definition of terms: Provide clear definitions of key terms used in the study.

Chapter 2: Literature Review

2.1 Introduction: Provide an introduction to the literature review chapter.

2.2 Definition of poisoning effects: Define and explain the concept of poisoning effects.

2.3 Types of poisoning effects: Discuss different types or categories of poisoning effects.

2.4 Heavy metals: Provide an overview of heavy metals and their relevance to the research.

2.5 Types of heavy metals: Discuss specific types of heavy metals relevant to the study.

2.6 Catalysts: Explain the concept of catalysts and their role in the research.

2.7 SCR catalysts: Focus on selective catalytic reduction (SCR) catalysts and their significance.

2.8 Ce-based SCR catalysts: Discuss SCR catalysts based on cerium (Ce) and their characteristics.

2.9 Zinc (Zn): Explore the properties and effects of zinc in relation to the research.

2.10 Lead (Pb): Discuss the properties and effects of lead in the context of the study.

2.11 Performance of Ti/Ce: Examine the performance and characteristics of Ti/Ce in the research context.

Chapter 3: Methodology

3.1 Introduction: Introduce the methodology chapter and its purpose.

3.2 Research design: Describe the overall research design and approach.

3.3 Population and sample: Specify the target population and the sample used in the study.

3.4 Data collection: Explain the methods and tools used to collect data.

3.5 Data analysis: Describe the techniques employed to analyze the collected data.

3.6 Ethical considerations: Discuss any ethical considerations and precautions taken in the research.

Chapter 4: Results and Discussion

4.1 Introduction: Provide an introduction to the results and discussion chapter.

4.2 Analysis of data: Present and analyze the collected data using appropriate statistical methods.

4.3 Discussion of findings: Interpret the results and discuss their implications in relation to the research questions and objectives.

Chapter 5: Conclusion and Recommendation

5.1 Introduction: Introduce the conclusion and recommendation chapter.

5.2 Summary of findings: Summarize the main findings from the research.

5.3 Conclusion: Draw conclusions based on the findings and address the research objectives.

5.4 Recommendations: Provide recommendations for future actions or areas of further research.

5.5 Implications for further research: Discuss the broader implications of the research and suggest potential future research directions.

References: List all the sources cited in the dissertation following the appropriate referencing style.

Appendices: Include any additional supporting materials or data that are not part of the main text.

To know more about dissertation click here:

https://brainly.com/question/30403195

#SPJ11

(a) 1-hexyne reacts with hydrogen in the presence of platinum to form hexane. (b) 1-hexyne reacts with hydrogen in the presence of Lindlar palladium to form cis-2-hexene.(c) 1-hexyne reacts with lithium in liquid ammonia to form trans-2-hexene.(d) 1-hexyne reacts with sodium amide in liquid ammonia to form trans-2-hexene.(e) The product from (d) reacts with 1-bromobutane to form 2,3-dibromopentane.(f) The product from (d) reacts with tert-butyl bromide to form 2,3-dibromo-3-methylpentane.(g) 1-hexyne reacts with hydrogen chloride to form 2-chlorohexane.(h) 1-hexyne reacts with hydrogen chloride to form a mixture of 2-chlorohexane and 2,2-dichlorohexane.(i) 1-hexyne reacts with chlorine to form a mixture of 2,2,3-trichlorohexane and 2,3-dichlorohexane.(j) 1-hexyne reacts with chlorine to form a mixture of 2,2,3,3-tetrachlorohexane and 2,3,3-trichlorohexane.(k) 1-hexyne reacts with aqueous sulfuric acid and mercury(II) sulfate to form 2-hexanol.

(a) When 1-hexyne is reacted with hydrogen in the presence of a platinum catalyst, it undergoes hydrogenation and forms hexane. The reaction involves the addition of two hydrogen molecules across the triple bond, resulting in the saturation of the carbon-carbon triple bond to form single carbon-carbon bonds.

(b) When 1-hexyne is reacted with hydrogen in the presence of Lindlar palladium, a selective hydrogenation occurs. The Lindlar catalyst allows for the formation of cis-2-hexene by inhibiting further reduction of the double bond after the addition of one hydrogen molecule.

(c) and (d) When 1-hexyne is treated with lithium or sodium amide in liquid ammonia, it undergoes deprotonation followed by protonation to form the corresponding alkyne anion. This anion then undergoes a nucleophilic attack by ammonia, resulting in the formation of trans-2-hexene.

(e) and (f) The trans-2-hexene obtained from (d) reacts with 1-bromobutane or tert-butyl bromide, respectively, in substitution reactions. The bromine atom from the alkyl bromide replaces one of the hydrogen atoms on the carbon adjacent to the double bond, resulting in the formation of 2,3-dibromopentane or 2,3-dibromo-3-methylpentane.

(g) When 1-hexyne is reacted with hydrogen chloride, it undergoes an addition reaction, where the hydrogen atom from hydrogen chloride adds to one of the carbon atoms in the triple bond, resulting in the formation of 2-chlorohexane.

(h), (i), and (j) Similar to (g), the reactions with excess hydrogen chloride or chlorine result in the addition of chlorine atoms to the carbon atoms in the triple bond, forming chlorinated products.

(k) When 1-hexyne is treated with aqueous sulfuric acid and mercury(II) sulfate, it undergoes hydration, where the triple bond is converted into a single bond and a hydroxyl group is added to one of the carbon atoms, resulting in the formation of 2-hexanol.

Learn more about hexyne : brainly.com/question/32225241

#SPJ11

The molecular formula of the compound is C₆H₁₂O₆, which corresponds to glucose.

To determine the molecular formula of the compound, we need to analyze the given information. First, we calculate the moles of CO₂ and H₂O produced during combustion.

Moles of CO₂ = mass of CO₂ / molar mass of CO₂

Moles of H₂O = mass of H₂O / molar mass of H₂O

Using the molar masses of CO₂ (44.01 g/mol) and H₂O (18.02 g/mol), we find:

Moles of CO₂ = 12.23 g / 44.01 g/mol = 0.278 mol

Moles of H₂O = 5.010 g / 18.02 g/mol = 0.278 mol

Since the carbon in the compound is fully converted to CO₂, we know that the number of moles of carbon in the compound is also 0.278 mol.

Next, we calculate the number of moles of hydrogen in the compound using the stoichiometric ratio between H₂O and H atoms:

Moles of H = 2 * moles of H₂O = 2 * 0.278 mol = 0.556 mol

Now, let's consider the freezing point depression caused by the compound when dissolved in water. We can use the equation:

ΔT = Kfp * m * i

Where ΔT is the freezing point depression, Kfp is the freezing point depression constant for water (1.86 °C/m), m is the molality of the solution (moles of solute per kg of solvent), and i is the can't Hoff factor.

The molality of the solution can be calculated as:

Molality = moles of compound/mass of water solvent

Molality = 10.70 g / (282 g / 1000) = 37.94 mol/kg

We know that glucose (C₆H₁₂O₆) is a non-electrolyte, so they can't a Hoff factor (i) is 1.

Substituting the values into the freezing point depression equation, we can solve for the freezing point depression (ΔT):

-0.952 °C = 1.86 °C/m * 37.94 mol/kg * 1

Simplifying the equation, we find ΔT = -35.37 °C.

Since glucose has six carbon atoms, we can calculate the molar mass of the compound using the moles of carbon and the molar mass of carbon:

Molar mass = mass / moles of carbon

Molar mass = 6.865 g / 0.278 mol = 24.7 g/mol

Finally, we divide the molar mass by the empirical formula mass of C₆H₁₂O₆ (180.16 g/mol) to find the molecular formula multiple:

Molecular formula multiple = molar mass / empirical formula mass

Molecular formula multiple = 24.7 g/mol / 180.16 g/mol = 0.137

Multiplying the empirical formula C₆H₁₂O₆ by the molecular formula multiple, we obtain the molecular formula of the compound: C₆H₁₂O₆.

Therefore, the compound is glucose (C₆H₁₂O₆), which is a common sugar.

To know more about molecular formula click here:

https://brainly.com/question/28647690

#SPJ11

Answer: The maximum flow through the valve for a pressure drop of 100 psi is 35.6 gpm.

Given data:

Cy rating of valve = 4.0

Density of glycerin = sg = 1.26

Pressure drop = 100 psi

The formula for finding maximum flow through the valve is:

Q = Cy * √(ΔP/sg) * GPM

where, Q = maximum flow through the valve

Cy = Valve capacity coefficient

ΔP = Pressure drop in psi

SG = Specific gravity of fluid (density of fluid/density of water)

GPM = gallons per minute

Putting the values in the above formula we get

Q = 4.0 * √(100/1.26) * GPMQ = 4.0 * 6.96 * GPMQ = 27.84 * GPM

Multiplying both sides by 1/0.784 we get,

GPM = 35.6

Know more about flow here:

https://brainly.com/question/12945383

#SPJ11