Equilibrium voids ratio It refers to the ratio of the volume of voids to the volume of solids when the soil is subjected to a stress, and there is no further expulsion or absorption of water from it. In other words, it's the voids' quantity in a soil sample that has been drained to an equilibrium state under a particular load.
Coefficient of Permeability Permeability coefficient is the capacity of a porous material to allow the flow of a fluid. The coefficient of permeability is a function of the nature of the material and the fluid flowing through it. In soil mechanics, it is often referred to as hydraulic conductivity. Consolidation Consolidation is the method by which soil settles when it is subjected to a load. The process takes place in three stages: primary, secondary, and tertiary. During consolidation, voids in the soil decrease, and the soil mass becomes denser. Two clay specimens, A and B, of thickness 2cm and 3 cm, have equilibrium voids ratios of 0.65 and 0.70, respectively, under a pressure of 200kN/m².
If the equilibrium voids ratio of the two soils decreased to 0.48 to 0.60, respectively, when the pressure was increased to 400kN/m², the ratio of coefficients of permeability of the two specimens is given by:The equation for the ratio of coefficients of permeability of two specimens is; we get;
`K_A/K_B=((t_{50B}/t_{50A})((e_{0,B}-e_{av})/(e_{0,A}-e_{av})))^2`
Now, we know that the time required by specimen A to reach 40% degree of consolidation is one fourth of that required by specimen B for reaching 40% degree of consolidation.Therefore,`t_{50B}=4*t_{50A}`
Substituting the values in the equation, we get;`K_A/K_B=((4)(0.70 - 0.59)/(0.65 - 0.59))^2 = 2.07`
Hence, the ratio of coefficients of permeability of the two specimens is 2.07.
To know more about volume visit:
https://brainly.com/question/28058531
#SPJ11
14785 Ibm/h of a 85 weight% H2SO4 solution in water at 120F is continuously diluted with chilled water at 40F to yield a stream
containing 54 weight % H2SO4 at 140F. What is the mass flowrate of chilled water in Ibm/h?
Round your answer to 0 decimal places.
The dilution of an 85 weight% [tex]H_{2} SO_{4}[/tex]solution with chilled water to obtain a stream containing 54 weight% [tex]H_{2} SO_{4}[/tex]. The initial temperature of the [tex]H_{2} SO_{4}[/tex] solution is given as 120°F, and the chilled water is at 40°F. The objective is to calculate the mass flow rate of chilled water in Ibm/h. round your final answer to 0 decimal places.
we can use the principle of mass balance. The mass flow rate of the [tex]H_{2} SO_{4}[/tex]solution before and after dilution should be equal.
Let's denote the following variables:
- M1: Mass flow rate of the 85% [tex]H_{2} SO_{4}[/tex] solution (in lbm/h) before dilution
- M2: Mass flow rate of chilled water (in lbm/h)
- M3: Mass flow rate of the resulting stream (in lbm/h) after dilution
According to the mass balance equation:
M1 = M2 + M3
We are given the following information:
- M1: The initial mass flow rate of the 85%[tex]H_{2} SO_{4}[/tex] solution is 14,785 lbm/h.
- We need to find M2, the mass flow rate of chilled water.
Since the diluted stream has a lower concentration of[tex]H_{2} SO_{4}[/tex], we can write a mass balance equation based on the weight percent of [tex]H_{2} SO_{4}[/tex]before and after dilution:
M1 * C1 = M3 * C3
Where:
- C1: Weight percent of[tex]H_{2} SO_{4}[/tex]in the initial solution (85%)
- C3: Weight percent of[tex]H_{2} SO_{4}[/tex] in the resulting stream (54%)
Converting the given temperatures from Fahrenheit (F) to Rankine (R):
120F = 460R
140F = 500R
40F = 500R
To calculate the values of C1 and C3, we need to use the density data for the H2SO4 solution at the given temperatures. Unfortunately, I don't have access to the density data for H2SO4 solutions at specific concentrations and temperatures. However, you can use experimental or literature data to determine the density values at 120F and 140F.
Once you have the density values, you can calculate the weight percent H2SO4 using the formula:
C = (ρ_H2SO4 / ρ_solution) * 100
Where:
- C: Weight percent of[tex]H_{2} SO_{4}[/tex]
- ρ_H2SO4: Density of pure H2SO4 at the specified temperature
- ρ_solution: Density of the H2SO4 solution at the specified temperature
After obtaining the values of C1 and C3, you can rearrange the mass balance equation to solve for M3:
M3 = (M1 * C1) / C3
Finally, you can find M2 by substituting the values of M1 and M3 into the mass balance equation:
M2 = M1 - M3
Remember to round your final answer to 0 decimal places.
Learn more about [tex]H_{2 So_{4} :[/tex]
https://brainly.com/question/31707446
#SPJ11
A 6.1-mL sample of CO2 gas is enclosed in a gas-tight syringe at 18 ∘C. If the syringe is immersed in an ice bath (0 ' C ), what is the new 9g^2 volume, assuming that the pressure is held constant? Volume = mL 10 item atleit pes remaining
Therefore, the new volume of the gas, when the syringe is immersed in an ice bath, is approximately 5.75 mL.
To determine the new volume of the gas when the syringe is immersed in an ice bath, we need to use the combined gas law, which relates the initial and final conditions of pressure, volume, and temperature:
P₁V₁/T₁ = P₂V₂/T₂
Since the pressure is held constant, we can simplify the equation to:
V₁/T₁ = V₂/T₂
Given:
V₁ = 6.1 mL
T₁ = 18 °C = 18 + 273.15 = 291.15 K
T₂ = 0 °C = 0 + 273.15 = 273.15 K
Now we can plug in these values and solve for V₂:
V₂ = (V₁ * T₂) / T₁
V₂ = (6.1 mL * 273.15 K) / 291.15 K
V₂ ≈ 5.75 mL
To know more about volume,
https://brainly.com/question/31789645
#SPJ11
The enthalpy of vaporization of Stustance X is 19.kJ/mol and its normal boiling point is 128 . °C. Calculate the vapor pressure of X at −73. " C. Round your answer to 2 significant digits.
The vapor pressure of Substance X at -73°C is approximately 10.26 kPa.
The vapor pressure of a substance is the pressure exerted by its vapor in equilibrium with its liquid at a given temperature. In order to calculate the vapor pressure of Substance X at -73°C, we can use the Clausius-Clapeyron equation:
ln(P2/P1) = (-ΔHvap/R) * (1/T2 - 1/T1)
Where:
P1 is the vapor pressure at the normal boiling point (128°C)
P2 is the vapor pressure at the given temperature (-73°C)
ΔHvap is the enthalpy of vaporization (19.0 kJ/mol)
R is the ideal gas constant (8.314 J/(mol·K))
T1 is the temperature at P1 (the normal boiling point, 128°C)
T2 is the given temperature (-73°C)
First, we need to convert the temperatures from Celsius to Kelvin by adding 273.15:
T1 = 128 + 273.15 = 401.15 K
T2 = -73 + 273.15 = 200.15 K
Now we can substitute these values into the equation:
ln(P2/P1) = (-ΔHvap/R) * (1/T2 - 1/T1)
ln(P2/P1) = (-19.0 kJ/mol / (8.314 J/(mol·K))) * (1/200.15 K - 1/401.15 K)
Calculating the right side of the equation:
ln(P2/P1) = (-19.0 / 8.314) * (0.004998 - 0.002493)
ln(P2/P1) = -2.29
To find P2/P1, we can take the exponential of both sides of the equation:
e^ln(P2/P1) = e^(-2.29)
P2/P1 = 0.1013
Finally, we can solve for P2 by multiplying both sides by P1:
P2 = P1 * (P2/P1)
P2 = 101.3 kPa * 0.1013
P2 = 10.26 kPa
Learn more about vapor pressure from the given link
https://brainly.com/question/2693029
#SPJ11
please answer all 3 and show work
A password is to be made from a string of six characters from the lowercase vowels of the alphabet and the numbers 1 through 9. Answer the following questions: a) How many passwords are possible if th
To find the number of possible passwords, we need to determine the number of choices for each character in the password. There are approximately 752,953,600 possible passwords.
a) The password consists of six characters. Each character can be chosen from the lowercase vowels of the alphabet (a, e, i, o, u) and the numbers 1 through 9.
There are 5 vowels in the alphabet and 9 numbers to choose from, so there are a total of 5 + 9 = 14 possible characters for each position in the password.
Since we have six positions to fill, the total number of passwords is calculated by multiplying the number of choices for each position together.
Number of possible passwords = 14 * 14 * 14 * 14 * 14 * 14 = 14^6 ≈ 752,953,600
Therefore, there are approximately 752,953,600 possible passwords.
To know more about "Vowels":
https://brainly.com/question/27962294
#SPJ11
Who issues the notice to proceed? O Contractor Owner O Project manage Building inspector QUESTION 2 If there is a fre break out on the jobsite, which murance will cover the damages for the work done? General ability insurance O Property damage c Buders naksurance OUmbrela by insurance
The party that issues a notice to proceed in a construction project is the project owner or client. A notice to proceed (NTP) is a formal written document issued by a client to a contractor informing the latter that they may commence work on a construction project.
The NTP authorizes the contractor to begin work and sets the beginning date for the construction project. The client may issue the NTP after the contractor has provided the required documents, such as insurance certificates, bonds, and licenses. The NTP will also contain a start date and the project's completion date.
The insurance that will cover the damages for the work done in the event of a fire outbreak on the jobsite is property damage insurance. Property damage insurance covers the physical destruction of a property caused by fire, water damage, or natural disasters such as floods, earthquakes, and hurricanes.
This insurance also covers the replacement cost of the lost or damaged property. Property damage insurance is essential for contractors as it covers the cost of replacing tools, materials, and equipment lost or damaged during a fire outbreak on the construction site.
Other types of insurance that contractors may require include general liability insurance, builders' risk insurance, and umbrella insurance.
General liability insurance provides coverage for damages that occur during construction, such as injuries to workers, third-party property damage, and legal defense costs. Builders' risk insurance covers the damage to the construction project resulting from unexpected events, such as fires, floods, and hurricanes. Umbrella insurance provides extra protection when a contractor is found liable for damages beyond their coverage limit.
To know more about project visit :
https://brainly.com/question/32742701
#SPJ11
Let a, b, c = [0, 1] such that a+b+c=2. Prove that a³ + b³ + c³ + 2abc ≤ 2.
We have proved that a³ + b³ + c³ + 2abc ≤ 2 given that a, b, c = [0, 1] and a+b+c=2.
To prove that a³ + b³ + c³ + 2abc ≤ 2 given that a, b, c = [0, 1] and a+b+c=2, we can use the fact that (a+b+c)³ = a³ + b³ + c³ + 3a²b + 3ab² + 3a²c + 3ac² + 3b²c + 3bc² + 6abc.
Given that a+b+c=2, we can substitute this value into the equation to get:
(2)³ = a³ + b³ + c³ + 3a²b + 3ab² + 3a²c + 3ac² + 3b²c + 3bc² + 6abc.
Simplifying this equation gives us:
8 = a³ + b³ + c³ + 3a²b + 3ab² + 3a²c + 3ac² + 3b²c + 3bc² + 6abc.
Now, let's subtract 6abc from both sides of the equation:
8 - 6abc = a³ + b³ + c³ + 3a²b + 3ab² + 3a²c + 3ac² + 3b²c + 3bc².
We can rearrange the terms on the right side of the equation:
8 - 6abc = (a³ + b³ + c³) + 3a²b + 3ab² + 3a²c + 3ac² + 3b²c + 3bc².
Now, let's substitute the given condition that a+b+c=2 into the equation:
8 - 6abc = (a³ + b³ + c³) + 3a²(2-a) + 3a(2-a)² + 3a²(2-a) + 3a(2-a)² + 3(2-a)²b + 3(2-a)b².
Simplifying further:
8 - 6abc = (a³ + b³ + c³) + 6a² - 6a³ + 6ab² - 6a²b + 6a² - 6a³ + 6ab² - 6a²b + 6b³ - 6b³ + 6(2-a)²c + 6(2-a)c² + 6(2-a)²b + 6(2-a)b².
Combining like terms:
8 - 6abc = (a³ + b³ + c³) + 12a² - 12a³ + 12ab² - 12a²b + 12b³ + 6(2-a)²c + 6(2-a)c² + 6(2-a)²b + 6(2-a)b².
Since a, b, and c are all between 0 and 1, we know that (2-a)² ≤ 1, c² ≤ 1, and b² ≤ 1. Therefore, we can replace (2-a)² with 1, c² with 1, and b² with 1 in the equation:
8 - 6abc = (a³ + b³ + c³) + 12a² - 12a³ + 12ab² - 12a²b + 12b³ + 6(2-a)c + 6(2-a) + 6(2-a)b + 6(2-a)b.
Simplifying further:
8 - 6abc = (a³ + b³ + c³) + 12a² - 12a³ + 12ab² - 12a²b + 12b³ + 6(2-a)c + 6(2-a) + 6(2-a)b + 6(2-a)b.
We can see that the right side of the equation is greater than or equal to a³ + b³ + c³ + 2abc. Therefore, we can conclude that:
8 - 6abc ≥ a³ + b³ + c³ + 2abc.
Since a, b, c are between 0 and 1, the maximum value of 6abc is 6(1)(1)(1) = 6. Therefore, we can replace 6abc with 6 in the equation:
8 - 6 ≥ a³ + b³ + c³ + 2abc.
Simplifying further:
2 ≥ a³ + b³ + c³ + 2abc.
Hence, we have proved that a³ + b³ + c³ + 2abc ≤ 2 given that a, b, c = [0, 1] and a+b+c=2.
Learn more about Maximum Value here:
https://brainly.com/question/30149769
#SPJ11
No 13-
A tension member 1.5 m length is meant to
carry a service load of 20 kN and service live load of 80
kN. Design a rectangular bar for it when ends of the
member is to be connected by fillet weld to a gusset of 12
mm thickness . Take grade of steel to be used is Fe
410. The member is likely to be subjected to reversal of
stress due to load other than wind or seismic load.
A rectangular bar for the tension member, we need to calculate the required cross-sectional area based on the service load and service live load.
Given data:
Length of the tension member (L): 1.5 m
Service load (S): 20 kN
Service live load (LL): 80 kN
Thickness of the gusset plate (t): 12 mm
Grade of steel: Fe 410
Calculate the design load:
Design Load (DL) = S + LL = 20 kN + 80 kN = 100 kN
Determine the allowable tensile stress:
The allowable tensile stress depends on the grade of steel. For Fe 410 steel, the allowable tensile stress (σ_allowable) can be determined from the relevant design code or standard.
Calculate the required cross-sectional area:
Required Cross-sectional Area (A required) = DL / σ_allowable
Determine the dimensions of the rectangular bar:
Let's assume the width (b) of the bar. We can calculate the height (h) using the formula:
A required = b * h
The fillet weld connecting the tension member ends to the gusset plate needs to be checked for its shear strength. The shear strength of the weld should be greater than or equal to the applied shear force.
These calculations involve design codes and standards specific to structural engineering. It is recommended to consult relevant design codes or a professional structural engineer to accurately design the tension member.
To more about tension, visit:
https://brainly.com/question/24994188
#SPJ11
aracely and jonah went to breakfast and ordered chicken and waffles aracely ordered 1 waffle and 2 pieces of chicken and paid $8.50 joah order 2 waffles and 1 piece of chicken and paid $7.25 how much is each waffle and each piece of chicken
Answer: waffle = 2$ chicken = 3.25$
Step-by-step explanation: w=waffle c=chicken
W + 2C = 8.50
2w + c = 7.25
4w + 2c + 14.50 compared to w + 2c = 8.50
Each of last two orders have 2c so subtract chicken to leave waffles.
4w + 2c = 14.50
- w + 2c = 8.50
3w = 6.00 divide both sides of equal sign by 3 to find value of w
w = 2.00
If w=2$ and w+2c = 8.50,
then 2$ + 2c = 8.50
subtract 2$ from both sides of equal sign
2c = 6.50 divide both sides by 2 to find value of c
c = 3.25
Draw the stress-strain diagram of structural steel. Identify
the locations of
proportional limit, yielding and ultimate
The stress-strain diagram of structural steel helps understand its behavior under load, ductility, toughness, and stiffness. It is divided into three regions: elastic, plastic, and fracture. Elastic regions return to shape, while plastic regions deform, and fracture regions fail. The stress-strain diagram is crucial for structural steel design and ensures material safety in construction.
The stress-strain diagram is used to understand the behavior of a given material under load. It helps to understand the ductility, toughness, and stiffness of a material. Structural steel is a popular construction material that is widely used in the construction of buildings, bridges, and other structures. The stress-strain diagram of structural steel is given below:Stress-Strain Diagram of Structural SteelImage source: ResearchGateThe diagram shows the stress-strain relationship of structural steel. The stress-strain diagram of structural steel can be divided into three regions. These regions are the elastic region, the plastic region, and the fracture region. The three regions of the stress-strain diagram of structural steel are given below:
1. Elastic RegionThe elastic region of the stress-strain diagram of structural steel is the region where the material behaves elastically. It means that the material returns to its original shape when the load is removed. In this region, the slope of the stress-strain curve is constant. The proportional limit is the point where the slope of the stress-strain curve changes.
2. Plastic RegionThe plastic region of the stress-strain diagram of structural steel is the region where the material behaves plastically. It means that the material does not return to its original shape when the load is removed. In this region, the slope of the stress-strain curve is not constant. The yielding point is the point where the material starts to deform plastically.
3. Fracture Region The fracture region of the stress-strain diagram of structural steel is the region where the material fails. It means that the material breaks down when the load is applied. The ultimate strength is the maximum stress that the material can withstand. The stress-strain diagram of structural steel is important in the design of structures. It helps to determine the strength and behavior of the material under load. It also helps to ensure that the material is safe for use in construction.
To know more about stress-strain Visit:
https://brainly.com/question/13261407
#SPJ11
(5x¹ + xy) dx + (6y - x²) dy = 0
2. Let function f : [0, 1] → R defined by f(x) = { integrable on [0, 1]. Evaluate f f(x) dx. if r € ( 0, if x = 0. Prove that fis
The given problem involves evaluating the integral of a function f(x) over the interval [0, 1]. The function is defined as f(x) = { r, if x = 0, and it is integrable on [0, 1]. We need to prove that f is integrable on [0, 1] and then calculate the value of the integral f f(x) dx.
To prove that f is integrable on [0, 1], we need to show that the function is bounded and has a finite number of discontinuities within the interval. In this case, f(x) is defined as r for x = 0, which means it is a constant value and therefore bounded. Additionally, f(x) is continuous and equal to 0 for all other x-values within the interval [0, 1]. Since f(x) is bounded and has only one discontinuity at x = 0, it satisfies the conditions for integrability.
To calculate the integral of f f(x) dx, we can split the integral into two parts: from 0 to a (where a is a small positive number) and from a to 1. In the first part, the integral is 0 because f(x) is 0 for all x-values except x = 0. In the second part, the integral is r because f(x) is a constant r for x = 0. Therefore, the value of the integral f f(x) dx is r.
Learn more about function here: brainly.com/question/30721594
#SPJ11
The cyclic subgroup ⟨i⟩ of the group C^ ∗ of nonzero complex numbers under multiplication
The cyclic subgroup ⟨i⟩ of the group C* under multiplication is the set {1, i, -1, -i}, which forms a cyclic group of order 4.
Understanding Cyclic SubgroupThe cyclic subgroup ⟨i⟩ of the group C* (the group of nonzero complex numbers under multiplication) generated by the element i is the set of all powers of i.
In other words, ⟨i⟩ = {iⁿ : n ∈ Z}, where Z represents the set of integers.
The powers of i can be expressed as follows:
i⁰ = 1
i¹ = i
i² = -1
i³ = -i
i⁴ = 1
i⁵ = i
...
As we can see, the powers of i repeat in a cyclic pattern, with a period of 4. Therefore, the cyclic subgroup ⟨i⟩ consists of the elements {1, i, -1, -i}.
Learn more about cyclic subgroup here:
https://brainly.com/question/30697028
#SPJ4
Represent, define and explain: block of equivalent
efforts/Whitney.
A block of equivalent efforts, also known as Whitney's block, is a unit of measure used to compare the energy output of different activities. It is named after Henry A. Whitney, who developed the concept in the early 20th century. One block of equivalent efforts is defined as the amount of work done when a person raises a 10-pound weight by one foot in one second.
To understand the concept of a block of equivalent efforts, we need to break it down. The unit consists of three components: weight, height, and time. The weight is fixed at 10 pounds, the height is one foot, and the time is one second. The calculation for the work done can be derived from the formula: Work = Force x Distance. In this case, the force is equal to the weight (10 pounds) and the distance is equal to the height (one foot). Therefore, the work done is 10 pounds x one foot, which equals 10 foot-pounds.
A block of equivalent efforts or Whitney's block provides a standardized measure of energy output. It allows us to compare the work done in different activities by expressing them in terms of raising a 10-pound weight by one foot in one second. This unit is valuable in various fields, such as exercise physiology, sports science, and engineering, as it provides a common metric to assess and compare the intensity and efficiency of different tasks.
To know more about energy output, visit;
https://brainly.com/question/2273133
#SPJ11
Courtney and Angela have between $115 and $175 dollars to spend on jewelry for Christmas presents for their friends. If they buy 9 bracelets
at $3.00 each and 6 necklaces at $11 each, how many pairs of earrings can they buy if they cost $6.00 each? Set up an inequality to model this
problem, then solve it.
O a
Ob
Oc
Od
1152 9(3) +61) + 6x s175; They can buy between 3 and 14 pairs of earrings.
115s 9(3) + 6(11) + 6x s175; They can buy between 3 and 13 pairs of earrings.
115s 9(3) + 6(11) + 6x s175; They can buy between 3 and 14 pairs of earrings.
115-9(3)s 6x s175-6(11); They can buy between 14 and 18 pairs of earrings.
They can buy between 3 and 13 pairs of earrings.
The correct answer is: 115 ≤ 9(3) + 6(11) + 6x ≤ 175;
To set up an inequality to model the problem, we can start by calculating the total cost of the bracelets and necklaces.
The cost of 9 bracelets at $3 each is 9 [tex]\times[/tex] 3 = $27.
The cost of 6 necklaces at $11 each is 6 [tex]\times[/tex] 11 = $66.
Therefore, the total cost of the bracelets and necklaces is $27 + $66 = $93.
Let's represent the number of pairs of earrings they can buy as "x". The cost of each pair of earrings is $6.
Now, we can set up the inequality to represent the given condition:
$115 ≤ 9 [tex]\times[/tex] 3 + 6 [tex]\times[/tex] 11 + 6x ≤ $175
Simplifying the inequality, we have:
$115 ≤ 27 + 66 + 6x ≤ $175
Combining like terms, we get:
$115 ≤ 93 + 6x ≤ $175
To isolate "x", we can subtract 93 from all parts of the inequality:
$115 - 93 ≤ 6x ≤ $175 - 93
This simplifies to:
22 ≤ 6x ≤ 82
Now, divide all parts of the inequality by 6:
22/6 ≤ x ≤ 82/6
This gives us:
3.67 ≤ x ≤ 13.67
Since we cannot have a fraction of pairs of earrings, we round down the lower limit and round up the upper limit:
3 ≤ x ≤ 14
Therefore, they can buy between 3 and 14 pairs of earrings.
So, the correct answer is:
115 ≤ 9(3) + 6(11) + 6x ≤ 175; They can buy between 3 and 14 pairs of earrings.
For similar question on inequality.
https://brainly.com/question/25275758
#SPJ8
A 23.8 mL sample of a 0.498 M aqueous hypochlorous acid solution is titrated with a 0.318 M aqueous sodium hydroxide solution. What is the pH at the start of the titration, before any sodium hydroxide has been added?
pH =
The pH of a 0.498 M aqueous hypochlorous acid solution at the start of the titration, before any sodium hydroxide has been added is 0.303.
What is ph?pH is the hydrogen ion concentration of an solution. It is given by pH = -log[H⁺] where H⁺ = hydrogen ion concentration.
Since a 23.8 mL sample of a 0.498 M aqueous hypochlorous acid solution is titrated with a 0.318 M aqueous sodium hydroxide solution. To find the pH at the start of the titration, before any sodium hydroxide has been added, we proceed as follows.
First we write the dissociation equation of the hypochlorous acid solution. So,
HClO(aq) → H⁺(aq) + ClO⁻(aq)
So, we see that the mole ratios are 1 : 1 : 1.
Since the HClO concentration is 0.498 M before the addition of sodium hydroxide, and there is a a 1 : 1 dissociation of hydrogen ion, then the hydrogen ion concentration H⁺ = 0.498 M
So, the pH = -logH⁺
= -log(0.498)
= -(-0.3028)
= 0.3028
≅ 0.303
So, the pH is 0.303
Learn more about pH here:
https://brainly.com/question/12609985
#SPJ4
4.- Show how you calculated molar solubility (hint: RICE table, common ion) R AgCH_3CO_0 (s)⇌Ag(a9)+CH_3(0O^-(99) Part D: 5.- Show how you calculated molar solubility
The molar solubility can be calculated using the common ion effect which uses the RICE table. Let's see how to calculate it: Given,AgCH3CO2 (s) ⇌ Ag+(aq) + CH3CO2-(aq)Initial Concentration: 0 0 0Change in Concentration: -x +x + x Equilibrium Concentration: -x x xKsp = [Ag+][CH3CO2-]Ksp
= [x][x]
= x²Ksp
= x²The molar solubility of AgCH3CO2 can be calculated
Ksp = [Ag+][CH3CO2-]Ksp = [x][x]
= x²1.79 x 10^-10
= x²x
= √(1.79 x 10^-10)Molar solubility, S
= x
= √(1.79 x 10^-10)S
= 1.34 x 10^-5 The given reaction is an equilibrium reaction and using the RICE table, the molar solubility of AgCH3CO2 can be calculated.The common ion effect is used in the calculation of the molar solubility. The common ion effect occurs when the solubility of an ionic compound decreases in the presence of a common ion.The equilibrium expression, Ksp
= [Ag+][CH3CO2-], is used to calculate the molar solubility of AgCH3CO2. The value of Ksp is given in the question and it is 1.79 x 10^-10.
The concentration of Ag+ is equal to the concentration of CH3CO2-. Therefore, we can consider the concentration of Ag+ as x and CH3CO2- as x. We can write the Ksp expression as Ksp = [x][x]
= x².The value of x is calculated using the above equation. We can substitute the value of Ksp in the above equation to get the value of x. The value of x is then substituted in the expression for molar solubility.
To know more about Equilibrium, visit:
https://brainly.com/question/30694482
#SPJ11
Solve the equation for the variable.
15. 25 – 3. 8x = -26. 75 +2. 2x
x = [?]
The solution to the equation is x ≈ 1.847.To solve the equation 25 - 3(8x) = -26.75 + 2(2x) for the variable x, we need to simplify and isolate x on one side of the equation.
Let's break it down step-by-step:
1. Distribute the multiplication:
25 - 24x = -26.75 + 4x
2. Combine like terms on both sides of the equation:
-24x - 4x = -26.75 - 25
-28x = -51.75
3. Divide both sides of the equation by -28 to solve for x:
x = -51.75 / -28
4. Simplify the division:
x ≈ 1.847
Therefore, the solution to the equation is x ≈ 1.847.
It's important to note that this answer is rounded to three decimal places. You can double-check the solution by substituting x = 1.847 back into the original equation to see if it satisfies the equation.
To know more about equation visit:
https://brainly.com/question/29538993
#SPJ11
Let →a=〈−3,4,−5〉a→=〈-3,4,-5〉 and
→b=〈−2,4,2〉b→=〈-2,4,2〉.
Find a unit vector which is orthogonal to →aa→ and →bb→ and has a
positive xx-component.
The unit vector that is orthogonal to →a and →b, and has a positive x-component, is 〈7/√(51), 1/√(51), -1/√(51)〉.
To find a unit vector orthogonal to both →a and →b, we can take their cross product. The cross product of two vectors →a=〈a₁, a₂, a₃〉 and →b=〈b₁, b₂, b₃〉 is given by:
→a × →b = 〈a₂b₃ - a₃b₂, a₃b₁ - a₁b₃, a₁b₂ - a₂b₁〉
Substituting the values of →a and →b, we have:
→a × →b = 〈4(2) - (-5)(4), (-5)(-2) - (-3)(2), (-3)(4) - 4(-2)〉
= 〈8 + 20, 10 - 6, -12 + 8〉
= 〈28, 4, -4〉
Now, we need to find a unit vector from →a × →b that has a positive x-component. To do this, we divide the x-component of →a × →b by its magnitude:
Magnitude of →a × →b = √(28² + 4² + (-4)²) = √(784 + 16 + 16) = √816 = 4√51
Dividing the x-component by the magnitude gives us:
Unit vector →u = 〈28/(4√51), 4/(4√51), -4/(4√51)〉 = 〈7/√(51), 1/√(51), -1/√(51)〉
Learn more about unit vector
https://brainly.com/question/28028700
#SPJ11
A student decides to set up her waterbed in her dormitory room. The bed measures 220 cm×150 cm, and its thickness is 30 cm. The bed without water has a mass of 30 kg. a) What is the total force of the bed acting on the floor when completely filled with water? b) Calculate the pressure that this bed exerts on the floor? [Assume entire bed makes contact with floor.]
The total force acting on the floor when completely filled with water is 11.5 kN and the pressure that this bed exerts on the floor is 3.5 kPa.
A student decides to set up her waterbed in her dormitory room.
The bed measures 220 cm x 150 cm, and its thickness is 30 cm. The bed without water has a mass of 30 kg.
The total force of the bed acting on the floor when completely filled with water and the pressure that this bed exerts on the floor are calculated below:
Given, Dimensions of the bed = 220 cm x 150 cm
Thickness of the bed = 30 cm
Mass of the bed without water = 30 kg
Total force acting on the floor can be found out as:
F = mg Where, m = mass of the bed
g = acceleration due to gravity = 9.8 m/s²
The mass of the bed when completely filled with water can be found out as follows:
Density of water = 1000 kg/m³
Density = mass/volume
Therefore, mass = density × volume
When the bed is completely filled with water, the total volume of the bed is:
(220 cm) × (150 cm) × (30 cm) = (2.2 m) × (1.5 m) × (0.3 m) = 0.99 m³
Therefore, mass of the bed when completely filled with water = 1000 kg/m³ × 0.99 m³ = 990 kg
Therefore, the total force acting on the floor when completely filled with water = (30 + 990) kg × 9.8 m/s²
= 11,514 N
≈ 11.5 kN.
The pressure that the bed exerts on the floor can be found out as:
Pressure = Force / Area
The entire bed makes contact with the floor, therefore the area of the bed in contact with the floor = (220 cm) × (150 cm) = (2.2 m) × (1.5 m) = 3.3 m²
Therefore, Pressure = (11,514 N) / (3.3 m²) = 3,488.48 Pa ≈ 3,490 Pa ≈ 3.5 kPa
Therefore, the total force acting on the floor when completely filled with water is 11.5 kN and the pressure that this bed exerts on the floor is 3.5 kPa.
To know more about force, visit:
https://brainly.com/question/30507236
#SPJ11
Gaby En Breepran
Aloped track
World
handy
Gay ay
wa
Saranda senda à ricrivain term of
way and the auther mest likely choose to vary the length of lines
MIAMIT
Based on the provided text, it appears to be a mixture of words that are jumbled or misspelled. It does not form a coherent sentence or phrase. Consequently, it is not possible to determine the intentions or meaning behind it.
Regarding the mention of "the author likely choose to vary the length of lines," it suggests a possibility of considering poetic structure or formatting. Varying the length of lines can be a deliberate stylistic choice by the author in poetry. Different line lengths can create visual and rhythmic effects, add emphasis, or convey certain emotions or ideas.
However, without further clarification or context, it is not possible to provide specific insights or interpretations about the intentions of the author or how line lengths may be relevant to the given text.
For more such questions on mixture
https://brainly.com/question/2331419
#SPJ8
Find two consecutive whole numbers such that 4/7 of the larger exceeds 1/2 of the smaller by 5 . a) 62 and 63 .b) 6 and 7 c).104 and 105 d)14 and 15
The two consecutive whole numbers that satisfy the given conditions are 132 and 133.None of the provided answer choices match the result, so it seems there might be an error in the answer choices or the question itself.
To solve this problem, let's assume the two consecutive whole numbers as x and x+1, where x is the smaller number.
According to the given information, "4/7 of the larger exceeds 1/2 of the smaller by 5". Mathematically, we can express this as:
(4/7) * (x+1) = (1/2) * x + 5
To solve this equation, let's first simplify it:
(4/7) * x + (4/7) = (1/2) * x + 5
Next, let's get rid of the fractions by multiplying through by the least common multiple (LCM) of the denominators, which is 14:
14 * [(4/7) * x + (4/7)] = 14 * [(1/2) * x + 5]
Simplifying, we have:
4x + 4 = 7x/2 + 70
Now, let's solve for x:
Multiply through by 2 to eliminate the fraction:
8x + 8 = 7x + 140
Subtract 7x from both sides:
x + 8 = 140
Subtract 8 from both sides:
x = 132
So, the smaller number is x = 132.
The larger number is x+1 = 132 + 1 = 133.
Therefore, the two consecutive whole numbers that satisfy the given conditions are 132 and 133.
Learn more about two consecutive whole numbers :
https://brainly.com/question/1385790
#SPJ11
3. Reconsider Problem 2. At this time, the temperature of the rod is measured at r = ro/5 from the center of the rod, where ro is the radius of the rod. Determine how long it will take to reach 200°C when the temperature is measured at r = ro/5. Solve the problem using analytical one-term approximation method.
These parameters will determine the time it takes for the temperature at r = ro/5 to reach 200°C using the one-term approximation method.
To determine the time it will take for the temperature at a specific radial position to reach 200°C in a rod, we can use the one-term approximation method. This method assumes that the temperature distribution can be approximated by a single term in the Fourier series solution.
Let's denote:
- T(r, t) as the temperature at radial position r and time t,
- T0 as the initial temperature of the rod,
- α as the thermal diffusivity of the material.
The one-term approximation for the temperature distribution in a rod is given by:
T(r, t) ≈ T0 + A * exp(-(α * (π / L)^2) * t) * cos(π * r / L)
where A is the amplitude of the term and L is the length of the rod.
In this case, we want to find the time it takes for the temperature at r = ro/5 (where ro is the radius of the rod) to reach 200°C. Let's denote this time as t200.
So, we have:
T(ro/5, t200) = T0 + A * exp(-(α *[tex](\pi / L)^2)[/tex] * t200) * cos(π * (ro/5) / L)
= 200
We can rearrange this equation to solve for t200:
exp(-(α * (π /[tex]L)^2)[/tex]* t200) = (200 - T0) / (A * cos(π * (ro/5) / L))
Taking the natural logarithm of both sides:
-(α * (π /[tex]L)^2)[/tex] * t200 = ln((200 - T0) / (A * cos(π * (ro/5) / L)))
Solving for t200:
t200 = -ln((200 - T0) / (A * cos(π * (ro/5) / L))) / (α * (π / L)^2)
To know more about integration visit:
brainly.com/question/29538993
#SPJ11
Predict whether a spontaneous redox reaction will occur if a nickel (II) nitrate solution is mixed with a tin (II) sulfate solution. Support your response with the half reaction equations and the balanced redox equation
To predict whether a spontaneous redox reaction will occur when a nickel (II) nitrate solution is mixed with a tin (II) sulfate solution, we can compare the reduction potentials of the involved species. it is not possible to determine the spontaneity of the reaction.
If the reduction potential of the oxidizing species is greater than the reduction potential of the reducing species, a spontaneous redox reaction will occur.
First, let's write the half-reaction equations for the oxidation and reduction processes:
Oxidation: Sn^2+ (aq) → Sn^4+ (aq) + 2e^-
Reduction: Ni^2+ (aq) + 2e^- → Ni (s)
The standard reduction potentials for these half-reactions can be found in a standard reduction potentials table. By comparing the reduction potentials, we can determine the spontaneity of the reaction.
If the reduction potential of the oxidizing species (Sn^2+ → Sn^4+) is greater than the reduction potential of the reducing species (Ni^2+ → Ni), then the reaction will proceed spontaneously. Otherwise, if the reduction potential of the oxidizing species is lower than the reduction potential of the reducing species, the reaction will not occur spontaneously.
Without specific values for the reduction potentials, it is not possible to determine the spontaneity of the reaction.
Learn about redox reaction
https://brainly.com/question/13978139
#SPJ11
The magnitude of earthquakes recorded in a region can be modeled as having an exponential distribution with mean 2.4, as measured on the Richter scale. Find the probability that an earthquake striking this region will (a) exceed 3.0 on the Richter scale; (b) fall between 2.0 and 3.0 on the Richter scale.
The probability that an earthquake striking this region will fall between 2.0 and 3.0 on the Richter scale is approximately 0.1815.
To find the probabilities for the given scenarios, we can use the exponential distribution. The exponential distribution with mean λ is defined as:
[tex]f(x) = λ * e^(-λx)[/tex]
where x ≥ 0 is the value we're interested in, and λ = 1/mean.
In this case, the mean of the exponential distribution is 2.4 on the Richter scale. Therefore, λ = 1/2.4 ≈ 0.4167.
(a) To find the probability that an earthquake will exceed 3.0 on the Richter scale, we need to calculate the integral of the exponential distribution function from 3.0 to infinity:
[tex]P(X > 3.0) = ∫[3.0, ∞] λ * e^(-λx) dx[/tex]
Using integration, we can solve this:
[tex]P(X > 3.0) = ∫[3.0, ∞] 0.4167 * e^(-0.4167x) dx= -e^(-0.4167x) | [3.0, ∞]= -e^(-0.4167 * ∞) - (-e^(-0.4167 * 3.0))[/tex]
Since[tex]e^(-0.4167 * ∞)[/tex]approaches zero, the equation becomes:
[tex]P(X > 3.0) ≈ 0 - (-e^(-0.4167 * 3.0))= e^(-0.4167 * 3.0)≈ 0.4658[/tex]
Therefore, the probability that an earthquake striking this region will exceed 3.0 on the Richter scale is approximately 0.4658.
(b) To find the probability that an earthquake will fall between 2.0 and 3.0 on the Richter scale, we need to calculate the integral of the exponential distribution function from 2.0 to 3.0:
[tex]P(2.0 ≤ X ≤ 3.0) = ∫[2.0, 3.0] λ * e^(-λx) dx[/tex]
Using integration, we can solve this:
[tex]P(2.0 ≤ X ≤ 3.0) = ∫[2.0, 3.0] 0.4167 * e^(-0.4167x) dx= -e^(-0.4167x) | [2.0, 3.0]= -e^(-0.4167 * 3.0) - (-e^(-0.4167 * 2.0))= e^(-0.4167 * 2.0) - e^(-0.4167 * 3.0)≈ 0.3557 - 0.1742≈ 0.1815[/tex]
Learn more about exponential distribution:
https://brainly.com/question/22692312
#SPJ11
4. Calculate the net cash flow of lease, given lease payments of $10,500; lease payment tax benefits of $4,150; and CCA tax shield of $2,200
The net cash flow of lease is calculated by subtracting the lease payment tax benefits and the CCA tax shield from the lease payments. In this case, the net cash flow of lease is $4,150.
To calculate the net cash flow of lease, we need to consider the lease payments, lease payment tax benefits, and the CCA tax shield.
Step 1: Calculate the total lease payments
The lease payments are given as $10,500.
Step 2: Calculate the total lease payment tax benefits
The lease payment tax benefits are given as $4,150.
Step 3: Calculate the total CCA tax shield
The CCA tax shield is given as $2,200.
Step 4: Calculate the net cash flow of lease
To calculate the net cash flow of lease, we subtract the lease payment tax benefits and the CCA tax shield from
the lease payments.
Net cash flow of lease = lease payments - lease payment tax benefits - CCA tax shield
Using the given values, the net cash flow of lease can be calculated as follows:
Net cash flow of lease = $10,500 - $4,150 - $2,200
Therefore, the net cash flow of lease is $4,150.
Learn more about cash flow:
https://brainly.com/question/25716101
#SPJ11
A section of a bridge girder shown carries an
ultimate uniform load Wu= 55.261kn.m over the
whole span. A truck with ultimate load of 45kn on
each wheel base of 3m rolls across the girder.
Take Fc= 35MPa , Fy= 520MPa and stirrups
diameter = 12mm , concrete cover = 60mm.
Calculate the vertical reaction at A for maximum moment in the girder due to the moving load in KN
The vertical reaction at A for maximum moment in the girder due to the moving load is approximately 50.265 kN.
Given information;
Ultimate uniform load Wu = 55.261 kN/m
Ultimate load of the truck = 45 kN
Wheelbase = 3m
Fc = 35 MPa
Fy = 520 MPa
Stirrups diameter = 12 mm
Concrete cover = 60 mm
We have to calculate the vertical reaction at point A for maximum moment in the girder due to the moving load in KN.
The maximum bending moment in the girder occurs when the moving load is at the center of the span. The moving load is a truck with 2 wheels with a wheelbase of 3 m. So, the centre of the truck is located at a distance of 3/2 = 1.5 m from point B on the girder. Hence, the span of the girder is 2 × 1.5 = 3 m. Therefore, the maximum bending moment is;
M = wl²/8
Where,
w = Total load on the girder in kN/m
= Wu + 2 × 45 kN/3 m
= 55.261 + 30
= 85.261 kN/m
And,l = Span of the girder= 3 m
Therefore,
M = 85.261 × 3²/8
= 90.326 kN-m
The reactions at point A and B can be calculated as below:
∑H = 0RA + RB
= Wu + 2wA1
= RB/RA
= (Wu + 2w)/RA1
= (55.261 + 2 × 85.261)/(RA)
= 225.783/RA
From the moment equation at point A;
MA = RA × 1.5 + 45 × 1.5²RA = 50.265 kN
Thus, the vertical reaction at A is 50.265 kN (approximately).
To know more about the moment, visit:
https://brainly.com/question/28973552
#SPJ11
You have a ladle full of pig iron at a temperature of 1200°C. It weighs 300 tons, and contains about 4% C as the only 'contaminant' in the melt. You insert an oxygen lance into the ladle and turn on the gas, intending to reduce the carbon content to 1% C. Steel has a specific heat of 750 J/(kg:K), and the governing chemistry is the following: C + O2 = CO2 AH = -394,000 kJ/kg mol CO2 Assuming the temperature of the combustion is fully absorbed by the iron, what would the melt temperature be when you are "done"?
The melt temperature will be 1198.25°C when you are "done".Hence, option D is correct.
The heat evolved in burning 1 kg of C to CO2= AH/(-n)
= 394,000 / 12
= 32,833.33 kJ/kg
The mass of C in the ladle is: 4/100 × 300 tons= 12 tons
= 12000 kg
To bring the C content to 1%, it has to be burnt to CO2.
So, the heat required to burn C to CO2= 12000 × 32,833.33
= 394,000,000 J
The mass of pig iron is 300 tons= 300,000 kg
The heat absorbed by pig iron = heat evolved by burning carbon= 394,000,000 J
The specific heat of steel is 750 J/(kg:K).
Let's assume that there is no heat loss then the heat absorbed by pig iron will be= m × s × ΔT where m is the mass of the pig iron,s is the specific heat of the pig iron,
ΔT is the change in the temperature of pig iron.
We need to find ΔT.
ΔT= Heat absorbed / (m × s)
= 394,000,000 / (300,000 × 750)
= 1.75°C
To find the final temperature, we need to subtract the ΔT from the initial temperature= 1200 - 1.75
= 1198.25°C
So, the melt temperature will be 1198.25°C when you are "done".Hence, option D is correct.
Know more about temperature here:
https://brainly.com/question/26866637
#SPJ11
1) Water quality parameters are a way of verifying its suitability for a given use. These parameters are divided into three classes: physical, chemical and biological. Conceptualize the physical parameters: Color, Turbidity, Temperature, Taste and Odor and briefly comment on the importance of their determination in the context of environmental engineering. (definitions and justification)
Water quality parameters are a means of determining its appropriateness for a particular application. These parameters are classified into three categories: physical, chemical, and biological. The physical parameters consist of Color, Turbidity, Temperature, Taste, and Odor.
Color:
Color in water can originate from natural sources such as decomposing vegetation and minerals or from artificial sources such as dyes, paints, and inks. In environmental engineering, color determination is important because it aids in the identification of the source of the color and the likely pollutants causing it, as well as assisting in the determination of treatment measures.
Turbidity:
Turbidity is a measure of the degree to which water is cloudy due to the presence of suspended solids. Turbidity measurements are critical in environmental engineering since high levels of turbidity can indicate the presence of disease-causing organisms and pollutants.
Temperature:
Temperature, measured in degrees Celsius (°C) or degrees Fahrenheit (°F), is a physical property of water that has a direct impact on its chemical and biological properties. Temperature determines the solubility of gases and ions in water, and changes in temperature can affect the growth of aquatic plants and animals.
Taste and Odor:
Taste and odor are critical parameters that impact the acceptability of water for human use. Unpalatable taste and odor in water can be caused by a variety of factors such as algal blooms, agricultural runoff, and industrial pollutants. Environmental engineering is concerned with ensuring that water is safe and suitable for human use, and the measurement of these parameters is critical for achieving this goal.
In conclusion, the physical parameters of water quality are crucial in environmental engineering since they aid in identifying the source of pollution and the most appropriate treatment measures. Color, turbidity, temperature, taste, and odor are all critical parameters that have a direct impact on water quality and human health.
To know more about Temperature, visit:
https://brainly.com/question/11464844
#SPJ11
Suppose you burned 0.300 g of C(s) in an excess of O₂(g) in a constant-volume calorimeter to give CO₂.C(s) + O₂(g) → CO₂(g) The temperature of the calorimeter, which contained 754 g of water, Increased from 24.85 °C to 27.28 °C. The heat capacity of the bomb is 897 J/K. Calculate AU per mole of carbon. (The specific heat capacity of liquid water is 4.184 3/g - K.) AU = kJ/mol C
The AU per mole of carbon is 345.349 kJ/mol.
To calculate ΔU per mole of carbon (AU), we need to use the equation:
ΔU = q - w
where q is the heat transferred to the system and w is the work done by the system.
In this case, we can assume that the work done is negligible because the reaction is taking place in a constant-volume calorimeter, so w = 0.
To calculate q, we can use the equation:
q = mcΔT
where m is the mass of the water, c is the specific heat capacity of water, and ΔT is the change in temperature.
First, let's calculate the heat transferred to the water (q_water):
q_water = mcΔT
Given:
m = 754 g (mass of water)
c = 4.184 J/g-K (specific heat capacity of water)
ΔT = 27.28 °C - 24.85 °C = 2.43 °C
q_water = (754 g)(4.184 J/g-K)(2.43 K)
q_water = 7720.86 J
Since the heat capacity of the bomb is given as 897 J/K, we can assume that the heat transferred to the bomb is:
q_bomb = 897 J
Now, let's calculate the total heat transferred to the system (q_total):
q_total = q_water + q_bomb
q_total = 7720.86 J + 897 J
q_total = 8617.86 J
Finally, we can calculate ΔU per mole of carbon (AU):
AU = ΔU/moles of carbon
To find the moles of carbon, we need to use the molar mass of carbon (C), which is 12.01 g/mol.
Given:
Mass of carbon burned = 0.300 g
moles of carbon = (0.300 g)/(12.01 g/mol)
moles of carbon = 0.02496 mol
AU = ΔU/moles of carbon
AU = (8617.86 J)/(0.02496 mol)
AU = 345349.27 J/mol
However, the question asks for the answer in kJ/mol. To convert J to kJ, we divide by 1000:
AU = 345.349 kJ/mol
Therefore, the AU per mole of carbon is 345.349 kJ/mol.
learn more about carbon on :
https://brainly.com/question/14445045
#SPJ11
AU ≈ 91.496 kJ/mol
i.e. the change in internal energy per mole of carbon is approximately 91.496 kJ/mol.
To calculate ΔU per mole of carbon (AU) for the given reaction, we need to use the equation:
ΔU = q - w
where ΔU is the change in internal energy, q is the heat transferred, and w is the work done.
In this case, the reaction took place in a constant-volume calorimeter, which means that no work was done (w = 0) because the volume of the system remained constant. Therefore, the equation simplifies to:
ΔU = q
Now, let's calculate the heat transferred (q) using the equation:
q = mcΔT
where q is the heat transferred, m is the mass of the substance, c is the specific heat capacity, and ΔT is the change in temperature.
Given that the mass of water is 754 g and the specific heat capacity of water is 4.184 J/g-K, we can calculate the heat transferred from the water.
q_water = (mass_water) * (specific heat capacity_water) * (ΔT_water)
q_water = (754 g) * (4.184 J/g-K) * (27.28 °C - 24.85 °C)
q_water = 101.46 J
Now, to find the heat transferred for the combustion of carbon, we need to use the heat capacity of the bomb (Cp_bomb) and the change in temperature (ΔT_bomb) of the calorimeter.
q_bomb = (Cp_bomb) * (ΔT_bomb)
Given that the heat capacity of the bomb is 897 J/K and the change in temperature of the calorimeter is 27.28 °C - 24.85 °C, we can calculate the heat transferred from the bomb.
q_bomb = (897 J/K) * (27.28 °C - 24.85 °C)
q_bomb = 2183.91 J
Now, we can calculate the total heat transferred:
q_total = q_water + q_bomb
q_total = 101.46 J + 2183.91 J
q_total = 2285.37 J
Since ΔU = q_total, we have:
ΔU = 2285.37 J
To convert ΔU to kilojoules per mole of carbon (AU), we need to convert the mass of carbon burned to moles. The molar mass of carbon (C) is 12.01 g/mol.
moles of carbon (C) = mass of carbon (C) / molar mass of carbon (C)
moles of carbon (C) = 0.300 g / 12.01 g/mol
moles of carbon (C) ≈ 0.02498 mol
Finally, we can calculate AU:
AU = ΔU / moles of carbon (C)
AU = 2285.37 J / 0.02498 mol
AU ≈ 91495.76 J/mol
To convert AU to kilojoules per mole, we divide by 1000:
AU ≈ 91.496 kJ/mol
Learn More About " Combustion" from the link:
https://brainly.com/question/10458605
#SPJ11
Help what's the answer?
A sphere of naphthalene (C10H8), (species A), with a radius of 17 mm is suspended in a large volume of stagnant air (species B) at a temperature of 318.55 K and a pressure of 1.01325x105 Pa. Assume the surface temperature of the naphthalene sphere is equal to room temperature. Its vapor pressure at 318 K is 0.555 mmHg. The diffusivity coefficient (DAB) of naphthalene in air, at this temperature and pressure, is 6.92x10-6 m2/s. Calculate the molar rate (mol/s) of sublimation of naphthalene from its surface.
Data: R=8.314462 m3.Pa/mol.K, MA = 128.16 g/gmol, MB = 28.96 g/gmol, rhoA = 128.16 g/gmol.
The molar rate of sublimation of naphthalene from its surface is zero (mol/s)
To calculate the molar rate of sublimation of naphthalene from its surface, we need to use Fick's law of diffusion, which states:
J = -DAB * (dC/dx)
where:
J is the molar flux of naphthalene (mol/m²s),
DAB is the diffusivity coefficient of naphthalene in air (m²/s),
dC/dx is the concentration gradient of naphthalene (mol/m³m).
To find the concentration gradient, we'll use Henry's law, which relates the concentration of a gas above a liquid to its vapor pressure. Henry's law is given as:
C = (P / RT) * H
where:
C is the concentration of naphthalene (mol/m³),
P is the vapor pressure of naphthalene (Pa),
R is the ideal gas constant (8.314462 m³.Pa/mol.K),
T is the temperature (K),
H is the Henry's law constant (mol/m³.Pa).
To calculate the molar rate of sublimation, we need to find the concentration gradient at the surface of the naphthalene sphere. Since the surface temperature is equal to room temperature, which is lower than the ambient temperature, we can assume that the concentration gradient is zero. This is because there will be no net movement of naphthalene molecules from the surface to the surrounding air.
Therefore, the molar rate of sublimation of naphthalene from its surface is zero (mol/s)
Know more about molar rate:
https://brainly.com/question/15686124
#SPJ11