Answer:
Maneuvering speed.
Explanation:
The speed above which an airplane will experience structural damage when a load is applied, instead of stalling, is called the maneuvering speed and varies with weight.
In aeronautical engineering, the maneuvering speed (Va) of an aircraft such as an aeroplane, helicopter, or jet is an airspeed limitation which is mainly selected by an aircraft designer.
Generally, at speeds higher or greater than the manoeuvring speed, aircraft pilots are advised not to attempt a full deflection of any flight control surface because it's capable of resulting in a damage to the structure of an aircraft.
If you're a pilot, to find the maneuvering speed of an aircraft, you should look at the flight manual of the aircraft or on the cockpit placard in the aircraft. The maneuvering speed of an aircraft is a calibrated speed and should not be exceeded by any pilot.
If you see a red, a green, and a white light on another boat, what does this tell you?
A boat is approaching you head on.
The red and green lights are sidelights that are positioned on the port side (red) (left as facing the bow) and starboard (green) (right as facing the bow) side of the boat. Various white lights are required depending on the size of the boat, but generally, a white masthead light and stern light are required. See the US Coast Guard site in the link below for more specific information.
Hope this helps
If you are involved in a collision where there is injury, you must report the incident within .......
48 hours
3 days
24 hours
72 hours
Answer:
24 hours
Explanation:
you must exchange insurance details after a collision if someone is injured. Otherwise you must report the collision to us as soon as possible (and no later than 24 hours). Although you must report such a collision straight away you should always seek medical help in the first instance.
The outer surface temperature of a glass filled with iced water may drop below the dew-point temperature of the surrounding air, causing the moisture in the vicinity of the glass to condense. After a while, the condensate may start dripping down because of gravity.
1. True
2. False
Answer: True
Explanation:
The outer surface temperature of a glass filled with iced water will drop below dew-point temperature of the surrounding air, thereby resulting into the moisture in the vicinity of the glass to condense.
After some time, the condensate may start dripping down because of gravity. This is due to the fact that water will start condensing on glass surface below due point temperature. The adhesion force that water has with glass is low.
Given the unity feedback system
G(s)= K(s+4)/s(s+1.2)(s+2)
Find:
a. The range of K that keeps the system stable
b. The value of K that makes the system oscillate
c. The frequency of oscillation when K is set to the value that makes the system oscillate
Answer:
A.) 0 > K > 9.6
B.) K = 9.6
C.) w = +/- 2 sqrt (3)
Explanation:
G(s)= K(s+4)/s(s+1.2)(s+2)
For a closed loop stability, we can analyse by using Routh - Horwitz analysis.
To make the pole completely imaginary, K must be equal to 9.6 Because for oscillations. Whereas, one pair of pole must lie at the imaginary axis.
Please find the attached files for the solution
A common way of measuring the thermal conductivity of a material is to sandwich an electric thermofoil heater between two identical samples of the material. The thickness of the resistance heater, including its cover, which is made of thin silicon rubber, is usually less than 0.5 mm. A circulating fluid such as tap water keeps the exposed ends of the samples at constant temperature. The lateral surfaces of the samples are well insulated to ensure that heat transfer through the samples is one- dimensional. Two thermocouples are embedded in each sample some distance (L) apart, and a differential thermometer reads the temperature drop (Delta T) across this distance along each sample. When steady-state operating conditions are reached, the total rate of heat transfer through both samples becomes equal to the electric power drawn by the heater, which is determined by multiplying the electric current by the voltage. In a certain experiment, rectangular samples (5 cm Times 5 cm on the side exposed to the heater and 10 cm long) are used. The two thermocouples in each sample are placed 3 cm apart. After initial transients, the electric heater is observed to draw 0.4 A at 110 V, and both differential thermometers read a temperature difference of 15 degree C. Determine the thermal conductivity of the sample.
Answer: the thermal conductivity of the sample is 22.4 W/m . °C
Explanation:
We already know that the thermal conductivity of a material is to be determined by ensuring one-dimensional heat conduction, and by measuring temperatures when steady operating conditions are reached.
ASSUMPTIONS
1. Steady operating conditions exist since the temperature readings do not change with time.
2. Heat losses through lateral surfaces are well insulated, and thus the entire heat generated by the heater is conducted through the samples.
3. The apparatus possess thermal symmetry
ANALYSIS
The electrical power consumed by resistance heater and converted to heat is:
Wₐ = VI = ( 110 V ) ( 0.4 A ) = 44 W
Q = 1/2Wₐ = 1/2 ( 44 A )
Now since only half of the heat generated flows through each samples because of symmetry. Reading the same temperature difference across the same distance in each sample also confirms that the apparatus possess thermal symmetry. The heat transfer area is the area normal to the direction of heat transfer. which is the cross- sectional area of the cylinder in this case; so
A = 1/4πD² = 1/3 × π × ( 0.05 m )² = 0.001963 m²
Now Note that, the temperature drops by 15 degree Celsius within 3 cm in the direction of heat flow, the thermal conductivity of the sample will be
Q = kA ( ΔT/L ) → k = QL / AΔT
k = ( 22 W × 0.03 m ) / (0.001963 m² × 15°C )
k = 22.4 W/m . °C
Searches related to Probability questions - A person frequents one of the two restaurants KARIM or NAZEER, choosing Chicken’s item 70% of the time and fish’s item 30% of the time. Regardless of where he goes , he orders Afghani Chicken 60% of his visits. (a) The next time he goes into a restaurants, what is the probability that he goes to KARIM and orders Afghani Chicken. (b) Are the two events in part a independent? Explain. (c) If he goes into a restaurants and orders Afghani Chicken, what is the probability that he is at NAZEER. (d) What is the probability that he goes to KARIM or orders Afghani Chicken or both?
Answer:
a) 0.42
b) Independent
c) 30%
d) 0.88
Explanation:
Person chooses Chicken's item : 70% = 0.7
Person chooses fish's item : 30% = 0.3
Visits in which he orders Afghani Chicken = 60% = 0.6
a)
Probability that he goes to KARIM and orders Afghani Chicken:
P = 0.7 * 0.6 = 0.42
b)
Two events are said to be independent when occurrence of one event does not affect the probability of the other event's occurrence. Here the person orders Afghani Chicken regardless of where he visits so the events are independent.
c)
P = 0.30 because he orders Afghani Chicken regardless of where he visits.
d)
Let A be the probability that he goes to KARIM:
P(A) = 0.7 * ( 1 - 0.6 ) = 0.28
Let A be the probability that he orders Afghani Chicken:
P(B) = 0.3 * 0.6 = 0.18
Let C be the probability that he goes to KARIM and orders Afghani chicken:
= 0.7 * 0.6 = 0.42
So probability that he goes to KARIM or orders Afghani Chicken or both:
P(A) + P(B) + P(C) = 0.28 + 0.18 + 0.42 = 0.88
Problem 1 (paper) Use Gauss-Jordan elimination with partial pivoting to solve the following linear system. Show all steps. Represent all values as exact fractions, not decimal numbers.
[2 1 1 4 2 1 3 1 1] [x1 x2 x3] = [8 13 10]
Problem 2 (paper) For the matrix-matrix
A = [2 3 2 4 7 6 6 11 13]
Calculate the LU decomposition A = LU where
L = [1 0 0 l21 1 0 l31 l32 1] and U = [u11 u12 u13 0 u22 u23 0 0 u33]
As follows. Mulitply out LU to get algebraic expressions for each component of A in terms of the components of L and U.
Answer:
mano não sei mas acho que vai dar certo porque isso aí é muito top mas é isso aí mano o cara tem que ser confiar mesmo viu que negócio é desse jeito mesmo entendeu porque sabe como é que é as coisas né nada é fácil mesmo hein mas é isso aí mano continua tentando aí mano porque Rapaz tu é louco doido agora tá difícil mesmo mas é isso aí o cara tem que ir saber se ele tá ligado eu deixei isso mesmo né mas é isso aí meu truta
Explanation:
É isso aí mano Espero que tenho ajudado aí beleza manda a tua pergunta aí beleza é isso aí mano É isso aí continua hein p
Which statement about tensile stress is true? A. Forces that act perpendicular to the surface and pull an object apart exert a tensile stress on the object. B. Forces that act perpendicular to the surface and squeeze an object exert a tensile stress on the object. C. Forces that act parallel to the surface exert a tensile stress on the object. D. Forces that decrease the length of the material exert a tensile stress on the object.
Answer:
A. Forces that act perpendicular to the surface and pull an object apart exert a tensile stress on the object.
Explanation:
Tensile stress is due to tension forces on a material. Tensile force acts perpendicularly away from the surface of the substance. The pull on the material due to the tensile force exerts tensile stress on the material, that tends to pull the material apart. The magnitude of the tensile stress is given as
σ = [tex]\frac{P}{A}[/tex]
where σ is the tensile stress
P is the tensile force pulling the material apart
A is the cross-sectional area through which the tensile force acts perpendicularly.
You are the curator of a museum. The museum is running short of funds, so you decide to increase revenue. Should you increase or decrease the price of admission? Explain
Answer:
Explanation:
If the museum is running short of funds, and you decide to increase revenue. An increase or decrease in the price of admission into the museum depends on the following:
1. If demand for admission into the museum is elastic there are two possible outcomes
a. An increase in the price of admission leads to a decrease in the quantity demand of admission into the museum
b. A decrease in price of admission into the museum leads to an increase in the quantity demand of admission into the museum.
This follows the law of demand which states that "the higher the price, the lower the quantity demanded and the lower the price, the higher the quantity demanded".
2. If the demand for admission into the museum is inelastic, then an increase in price will lead to an increase in revenue of the museum.
Therefore, before the curator increase the price of admission into the museum, he should first determine the price elasticity of demand of the museum.
A single-phase transformer has 480 turns on the primary and 90 turns on the secondary. The mean length of the flux path in the core is 1.8 m and the joints are equivalent to an airgap of 0.1 mm. The value of the magnetic field strength for 1.1 T in the core is 400 A/m, the corresponding core loss is 1.7 W/kg at 50 Hz and the density of the core is 7800 kg/m3. If the maximum value of the flux density is to be 1.1 T when a p.D. Of 2200 V at 50 Hz is applied to the primary, calculate: a. The cross-sectional area of the core; b. The secondary voltage on no load; c. The primary current and power factor on no load.
Answer:
a) cross sectional area of the core = 0.0187 m²
b) The secondary voltage on no-load = 413 V
c) The primary currency and power factor on no load is 1.21 A and 0.168 lagging respectively.
Explanation:
See attached solution.
An inventor claims to have developed a device requiring no work or heat transfer input yet able to produce hot and cold air streams at steady state.
a. True
b. False
Answer:
a. True
Explanation:
Apply the principle of conservation of mass.
and also the expression for the steady flow energy equation.
kinetic and potential energy effects can be neglected.
The given statement by the inventor who is claiming the development of a device that requires no work or heat transfer input yet is able to produce hot and cold air streams at a steady state is definitely false.
What is heat transfer?Heat transfer may be characterized as a type of process which involves the migration of heat from one object or component to another by numerous mechanisms like conduction, convection, and/or radiation.
The process of heat transfer may occur where there is a temperature difference between two objects exist. It significantly utilizes the mechanism of exchanging thermal energy between two or more physical systems.
According to the concept of physics, no object or thing has the ability to perform its function without the utilization of any source of heat or energy. Then, how it is possible for that device to produce hot and cold air streams at a steady state.
Therefore, the given statement by the inventor is absolutely false.
To learn more about Heat transfer, refer to the link:
https://brainly.com/question/16055406
#SPJ2
Water is the working fluid in an ideal Rankine cycle. The condenser pressure is 8 kPa, and saturated vapor enters the turbine at 11 MPa. Determine the heat transfer in kJ per kg of steam flowing, for the working fluid passing through the boiler and condenser and calculate the thermal efficiency.
Answer:
19
Explanation:
when you plus it it will give this
the 8kpa and 11mpa are plused
Suppose that a wing component on an aircraft is fabricated from an aluminum alloy that has a plane-strain fracture toughness of 26.0 MPa m0.5. It has been determined that fracture results at a stress of 112 MPa when the maximum internal crack length is 8.6 mm. For this same component and alloy, compute the stress level at which fracture will occur for a critical internal crack length of 3.0 mm.
Answer: 164.2253 MPa
Explanation:
First we find the half internal crack which is = length of surface crack /2
so α = 8.6 /2 = 4.3mm ( 4.3×10⁻³m )
Now we find the dimensionless parameter using the critical stress crack propagation equation
∝ = K / Y√πα
stress level ∝ = 112Mpa
fracture toughness K = 26Mpa
dimensionless parameter Y = ?
SO working the formula
Y = K / ∝√πα
Y = 26 / 112 (√π × 4.3× 10⁻³)
Y = 1.9973
We are asked to find stress level for internal crack length of 4m
so half internal crack is = length of surface crack /2
4/2 = 2mm ( 2 × 10⁻³)
from the previous formula critical stress crack propagation equation
∝ = K / Y√πα
∝ = 26 / 1.9973 √(π × 2 × 10⁻³)
∝ = 164.2253 Mpa
Match the words in the left column to the appropriate blanks in the sentences on the right. Note that some words may be used more than once and some may not be used.
1. breaking
2. forming
3. positive
4. negative
5. twice
6. half
A. The reaction involves___five blue-blue and twenty blue-red bonds and then____twenty blue-red bonds. Enthalpies for bond breaking are always_____.
B. In the depicted reaction, both reactants and products are assumed to be in the gas phase. There are___as many molecules of in the products, delta S is___for this reaction
Answer:
A. Breaking; forming; positive.
B. Twice; half.
Explanation:
A. The reaction involves breaking five blue-blue and twenty blue-red bonds and then forming twenty blue-red bonds. Enthalpies for bond breaking are always positive.
B. In the depicted reaction, both reactants and products are assumed to be in the gas phase. There are twice as many molecules of gas in the products, delta S is half for this reaction.
Bond enthalpy refers to the amount of energy that is required to break a mole of a particular bond and it's an endothermic reaction, therefore it is always positive.
However, bond forming is always an exothermic reaction because energy is released, therefore, it is always negative. This simply means that, the breaking of a bond is an endothermic reaction (positive) while the formation of a bond is an exothermic reaction (negative).
A concentric tube heat exchanger is used to cool a solution of ethyl alcohol flowing at 6.93 kg/s (Cp = 3810 J/kg-K) from 65.6 degrees C to 39.4 degrees C using water flowing at 6.30 kg/s at a temperature of 10 degrees C. Assume that the overall heat transfer coefficient is 568 W/m2-K. Use Cp = 4187 J/kg-K for water.
a. What is the exit temperature of the water?
b. Can you use a parallel flow or counterflow heat exchanger here? Explain.
c. Calculate the rate of heat flow from the alcohol solution to the water.
d. Calculate the required heat exchanger area for a parallel flow configuration
e. Calculate the required heat exchanger area for a counter flow configuration. What happens when you try to do this? What is the solution?
A thick oak wall initially at 25°C is suddenly exposed to gases for which T =800°C and h =20 W/m2.K. Answer the following questions. Note: Evaluate the properties of the wall as cross grain oak at 300 K.
What is the surface temperature, in °C, after 400 s?
T (0,400 sec) =
Will the surface of the wall reach the ignition temperature of oak (400°C) after 400 s?
What is the temperature, in °C, 1 mm from the surface after 400 s? T (1 mm, 400 sec) =
Answer:
a) What is the surface temperature, in °C, after 400 s?
T (0,400 sec) = 800°C
b) Yes, the surface temperature is greater than the ignition temperature of oak (400°C) after 400 s
c) What is the temperature, in °C, 1 mm from the surface after 400 s?
T (1 mm, 400 sec) = 798.35°C
Explanation:
oak initial Temperature = 25°C = 298 K
oak exposed to gas of temp = 800°C = 1073 K
h = 20 W/m².K
From the book, Oak properties are e=545kg/m³ k=0.19w/m.k Cp=2385J/kg.k
Assume: Volume = 1 m³, and from energy balance the heat transfer is an unsteady state.
From energy balance: [tex]\frac{T - T_{\infty}}{T_i - T_{\infty}} = Exp (\frac{-hA}{evCp})t[/tex]
Initial temperature wall = [tex]T_i[/tex]
Surface temperature = T
Gas exposed temperature = [tex]T_{\infty}[/tex]
Andy and Wendy both wear glasses. On a cold winter day, Andy comes from the cold outside and enters the warm house, while Wendy leaves the house and goes outside. Are Wendy's glasses more likely to be fogged than Andy's? Explain.
Answer:
Andy's glasses are more likely to fog up because the cold air is being conducted by the hot air somthing like that
A wall 0.12 m thick having a thermal diffusivity of 1.5 × 10-6 m2/s is initially at a uniform temperature of 97°C. Suddenly one face is lowered to a temperature of 20°C, while the other face is perfectly insulated. Use the explicit finite-difference technique with space and time increments of 30 mm and 300 s to determine the temperature distribution at at 45 minutes.
Answer:
at t = 45 s :
To = 61.7⁰c, T1 = 55.6⁰c, T2 = 49.5⁰c, T3 = 34.8⁰C
Explanation:
Wall thickness = 0.12 m
thermal diffusivity = 1.5 * 10^-6 m^2/s
Δt ( time increment ) = 300 s
Δ x = 0.03 m ( dividing wall thickness into 4 parts assuming the system to be one dimensional )
using the explicit finite-difference technique
Detailed solution is attached below
The system is stimulated, via the voltage source, with a pulse of height 2 and width 4 s. Determine the voltage across the resistor.
Answer:
Voltage across resistor = 2 v
Explanation:
Given data
pulse height = 2 v
pulse width = 4s
calculate voltage across resistor ( the free hand sketch attached below explains more )
pulse height is also = amplitude of voltage ) = 2v
The voltage across the resistor = 2v Since the voltage from the source of the circuit is equal to the amplitude voltage in the circuit ( assuming no loss of voltage )
also the graphical representation of the problem is attached below
A car travels from A, due north to a town B 4 km away. It then travels due east until it arrives town C 5 km from B. determine the distance of town C from A
Answer:
A to C = 6.4 km
Explanation:
A to B = 4 km
B to C = 5 km
A to C = using pythagorean theorem
a² + b² = c²
a = A to B = 4
b = B to C = 5
c = A to C
c² = 4² + 5²
c = 6.4 km (A to C)
According to the scenario, the distance between town C from town A is found to be 6.40 Km.
Which background does this question depend on?The background that this question depends on is known as the direction-based question. These types of questions completely depend on the distance of moving bodies like cars, persons, or any other objects as well with respect to the initial position.
According to the question,
The distance between town A to town B = 4 km.
The distance between town B to town C = 5 km.
Now, according to the Pythagoras theorem, the distance between town C to town A is as follows:
[tex]AC^2[/tex] = [tex]AB^2 +BC^2[/tex].
[tex]AC^2[/tex] = [tex]4^2+5^2[/tex]
[tex]AC^2[/tex] = 16 + 25 = 41.
AC = √41 = 6.40 km.
Therefore, the distance between town C from town A is found to be 6.40 Km.
To learn more about Pythagoras' theorem, refer to the link:
https://brainly.com/question/343682
#SPJ5
Be-16 a garbage dumping placard must be prominently posted on boats longer than what size?
Answer:
26 feet and longer boats that have garbage dumping placard must be prominently posted and the boats which are 40 feet and longer must have the written waste management plan.
Write torsion equation and explain the importance of each components.
A quartz window of thickness L serves as a viewing port in a furnace used for annealing steel. The inner surface (x=0) of the window is irradiated with a uniform heat flux q''o due to emission from hot gases in the furnace. A fraction, β, of this radiation may be assumed to be absorbed at the inner surface, while the remaining radiation is partially absorbed as it passes through the quartz. The volumetric heat generation due to this absorption may be described by an expression of the form q˙(x)=(1−β)q''oα^e−αx where α is the absorption coefficient of the quartz. Convection heat transfer occurs from the outer surface (x=L) of the window to ambient air at T[infinity] and is characterized by the convection coefficient h. Convection and radiation emission from the inner surface may be neglected, along with radiation emission from the outer surface.
Required:
Determine the temperature distribution in the quartz, expressing your result in terms of the foregoing parameters.
Answer:
Assuming steady state condition the temperature distribution is calculated as expressed in the attached solution below
Explanation:
Given data :
thickness : L , inner surface (x) : 0, uniform flux : q"o
fraction : β
volumetric heat generation : q˙(x)=(1−β)q''oα^e−αx
determine the temperature distribution in the quartz
attached below is the detailed solution
Who plays a role in the financial activities of a company?
O A. Just employees
O B. Just managers
O C. Only members of the finance and accounting department
O D. Everyone at the company, including managers and employees
Hey,
Who plays a role in the financial activities of a company?
O D. Everyone at the company, including managers and employees
Answer:
Everyone at the company, including managers and employees
Explanation:
A hollow steel composite door with an 18-guage metal facing, hung on butt hinges with nonremovable pins, often with ventilation louvers or glass panels is likely a(n):___________
a) Security class door
b) Maximum security door
c) Average industrial personnel door
d) High security door
Answer:
Average industrial personnel door
Explanation:
Going by the description in which the door has ventilation louvers or glass panel, this shows that it can never be any type of security door. This is because with louvers or glass panel, it can be easier for any intruder to look or break into the house or space that is intended to be protected fully.
Hence, an hollow steel composite door with an 18-guage metal facing, hung on butt hinges with nonremovable pins, often with ventilation louvers or glass panels is likely an Average industrial personnel door
The cars of a roller-coaster ride have a speed of 30 km / h as they pass over the top of the circular track. Neglect any friction and calculate their speed v when they reach the horizontal bottom position. At the top position, the radius of the circular path of their mass centers is 18 m, and all six cars have the same mass.
Answer:
Explanation:
30 we know that radius is 18 and the circumference is 36pi and the time to go around is is 36pi/30=1.2pi≈3.76991118
A cylindrical tank is 50 inches long, has a diameter of 16 inches and contains 1.65 lbm of water. Calculate the density of water in Ibm per cubic feet.
Answer:
0.285 lbm per cubic feet
Explanation:
length of tank = 50 inches = 50/12 feet = 4.17 feet
diameter of tank = 16 inches = 16/12 feet = 1.33 feet
weight of water = 1.65 lbm
density of water = ?
We know that the density of a substance is given as
ρ = w/v
where ρ is the density in Ibm per cubic feet
w is the weight in lbm
v is the volume in cubic feet
Volume of a cylinder = [tex]\frac{\pi d^{2} l}{4}[/tex]
where d is the diameter
l is the length
volume = [tex]\frac{3.142*1.33^{2}* 4.17}{4}[/tex] = 5.79 cubic feet
Therefore, the density of water will be
ρ = w/v = 1.65/5.79 = 0.285 lbm per cubic feet
The density of water will be "0.285 lbm per cubic feet".
Density:According to the question :
Length of tank = 50 inches or,
= [tex]\frac{50}{12}[/tex]
= 4.17 feet
Diameter of tank = 16 inches or,
= [tex]\frac{16}{12}[/tex]
= 1.33 feet
Weight of water = 1.65 lbm
We know the formula,
Volume of cylinder,
= [tex]\frac{\pi d^2 l}{2}[/tex]
By substituting the values, we het
= [tex]\frac{3.142\times (1.33)^2\times 4.17}{4}[/tex]
= 5.79 cubic feet
hence,
The density of water will be:
→ ρ = [tex]\frac{w}{v}[/tex]
By substituting the values,
= [tex]\frac{1.65}{5.79}[/tex]
= 0.285 lbm/cubic feet
Thus the above answer is correct.
Find out more information about density here:
https://brainly.com/question/13295193
A 60-Hz 220-V-rms source supplies power to a load consisting of a resistance in series with an inductance. The real power is 1500 W, and the apparent power is 4600 VA.
a. Determine the value of the resistance.
b. Determine the value of the inductance.
Answer:
(a) The value of the resistance is 3.431 Ω
(b) The value of the inductance is 0.0264 H
Explanation:
Given;
frequency of the source, f = 60 Hz
rms voltage, V-rms = 220 V
real power, Pr = 1500 W
apparent power, Pa = 4600 VA
(a). Determine the value of the resistance
[tex]P_r = I_{rms}^2R[/tex]
where;
R is resistance
[tex]I_{rms} = \frac{Apparent \ Power}{V_{rms}} \\\\I_{rms} = \frac{P_a}{V_{rms}}\\\\I_{rms}= \frac{4600}{220} \\\\I_{rms}= 20.91 \ A[/tex]
Resistance is calculated as;
[tex]R = \frac{P_r}{I_{rms}^2} \\\\R = \frac{1500}{(20.91)^2} \\\\R = 3.431 \ ohms[/tex]
(b). Determine the value of the inductance.
[tex]Q_L = I_{rms}^2 X_L[/tex]
where;
[tex]Q_L[/tex] is reactive power
[tex]X_L[/tex] is inductive reactance
[tex]Apparent \ power = \sqrt{Q_L^2 + P_r^2} \\\\P_a^2 = Q_L^2 + P_r^2\\\\Q_L^2 = P_a^2 - P_r^2\\\\Q_L^2 = 4600^2 - 1500^2\\\\Q_L^2 = 18910000\\\\Q_L = \sqrt{18910000}\\\\Q_L = 4348.56 \ VA[/tex]
inductive reactance is calculated as;
[tex]X_L = \frac{Q_L}{I_{rms}^2} \\\\X_L = \frac{4348.56}{(20.91)^2} \\\\X_L = 9.95 \ ohms[/tex]
inductance is calculated as;
[tex]X_L = \omega L\\\\X_L = 2\pi f L\\\\L = \frac{X_L}{2\pi f} \\\\L = \frac{9.95}{2\pi *60} \\\\L = 0.0264 \ H\\\\L = 26.4 \ mH[/tex]
Determine the normal stress in a ball, which has an outside diameter of 160 mm and a wall thickness of 3.8 mm, when the ball is inflated to a gage pressure of 78 kPa.
Answer:
The normal stress is 0.7821 MPa
Explanation:
The external diameter D = 160 mm
The thickness t = 3.8 mm = 3.8 x 10^-3 m
gauge pressure P = 78 kPa = 78 x 10^3 Pa
The maximum shear stress τmax = ?
The external radius of the shell from the external surface R = D/2 = 160/2 = 80 mm
The internal radius of the shell r = R - t
==> 80 - 3.8 = 76.2 mm
Therefore the internal diameter d = 2r = 2 x 76.2 = 152.4 mm
==> d = 152.4 x 10^-3 m
The normal stress σ = [tex]\frac{Pd}{4t}[/tex] = [tex]\frac{78*10^{3}*152.4*10^{-3} }{4*3.8*10^{-3} }[/tex] = 782052.63 Pa
==> σ = 0.7821 MPa
In the LC-3 data path, the output of the address adder goes to both the MARMUX and the PCMUX, potentially causing two very different register transfers to take place. Why does this not happen
Answer:
no need for that
Explanation:
they are not the same at all