The unsteady state population balance can be used to describe the cooling crystallisation process. This equation is used to describe the dynamic changes in crystal population during the process.
The seeded batch cooling crystallization process is considered the best option for the purification of an API. The following is the detailed explanation of a general crystallizer with unsteady and steady-state population balances and their meaning: Unsteady-state population balance: The unsteady-state population balance for a general crystallizer can be written as: dN/dt = G - R Here, dN/dt = Rate of accumulation of crystals in the crystallizer, , G = Generation rate of crystals due to nucleation, R = Rate of removal of crystals due to growth. The physical meaning of each term appearing in the equation: G: The generation rate of crystals (i.e., the rate of appearance of new crystals) is related to nucleation. R: The rate of removal of crystals (i.e., the rate at which the existing crystals disappear) is related to growth. dN/dt: The rate of accumulation of crystals is related to the difference between the generation and removal rates. Steady-state population balance: The steady-state population balance for a general crystallizer can be written as:G = R, Here, G = Generation rate of crystals due to nucleation R = Rate of removal of crystals due to growth. The population balance under steady-state conditions describes a process that has reached equilibrium and is in a state of balance between the rates of generation and removal. When the rate of nucleation equals the rate of growth, the system has reached steady-state, and the generation rate equals the removal rate.
Therefore, the unsteady-state population balance for a general crystallizer can be written as dN/dt = G - R, while the steady-state population balance for a general crystallizer can be written as G = R.
learn more about crystallisation visit:
brainly.com/question/31058900
#SPJ11
Please help me on this I will mark you brainlist :)))))))
The sequence is arithmetic, and the common difference is of 10.
What is an arithmetic sequence?An arithmetic sequence is a sequence of values in which the difference between consecutive terms is constant and is called common difference d.
The common difference of the sequence in this problem is given as follows:
40 - 30 = 10.30 - 20 = 10.20 - 10 = 10.As the common difference is equal, the sequence is arithmetic.
More can be learned about arithmetic sequences at https://brainly.com/question/6561461
#SPJ1
speed by ing angutar compute linear velocity from this, the speedometer needs to know the radius of the wheels. This information is programmed when the car is produced. If this radius changes (if you get different tires, for instance), the calculation becomes inaccurate. Suppose your car's speedometer is geared to accurately give your speed using a certain tire size: 13.5-inch diameter wheels (the metal part) and 4.65-inch tires (the rubber part). If your car's instruments are properly calibrated, how many times should your tire rotate per second if you are travelling at 45 mph? rotations per second Give answer accurate to 3 decimal places. Suppose you buy new 5.35-inch tires and drive with your speedometer reading 45 mph. How fast is your car actually traveling? mph Give answer accurate to 1 decimal place. Next you replace your tires with 3.75-inch tires. When your speedometer reads 45 mph, how fast are you really traveling? mph Give answer accurate to 1 decimal places.
- When your car's speedometer reads 45 mph with the 4.65-inch tires, your tires rotate approximately 4.525 times per second.
- When you have the new 5.35-inch tires and your speedometer reads 45 mph, your car is actually traveling at approximately 3.93 rotations per second.
- When you have the new 3.75-inch tires and your speedometer reads 45 mph, your car is actually traveling at approximately 5.614 rotations per second.
Step 1: Convert the tire size to radius
To find the radius of the tire, we divide the diameter by 2. So the radius of the 4.65-inch tire is 2.325 inches.
Step 2: Find the circumference of the tire
The circumference of a circle is calculated using the formula C = 2πr, where C is the circumference and r is the radius. Plugging in the radius, we get C = 2π(2.325) = 14.579 inches.
Step 3: Calculate the number of rotations per second
To find the number of rotations per second, we need to know the linear velocity of the car. We are given that the car is traveling at 45 mph.
To convert this to inches per second, we multiply 45 mph by 5280 (the number of feet in a mile), and then divide by 60 (the number of minutes in an hour) and 60 again (the number of seconds in a minute). This gives us a linear velocity of 66 feet per second.
Next, we need to calculate the number of rotations per second. Since the circumference of the tire is 14.579 inches, for every rotation of the tire, the car moves forward by 14.579 inches. Therefore, to find the number of rotations per second, we divide the linear velocity (66 inches/second) by the circumference of the tire (14.579 inches). This gives us approximately 4.525 rotations per second.
So, when your car's speedometer reads 45 mph, the tires should rotate approximately 4.525 times per second.
Now, let's consider the scenario where you buy new 5.35-inch tires and drive with your speedometer reading 45 mph.
Step 4: Calculate the new linear velocity
Following the same steps as before, we find that the new tire has a radius of 2.675 inches (half of 5.35 inches). The circumference of the new tire is approximately 16.795 inches.
Using the linear velocity of 45 mph (66 inches/second), we divide by the new circumference of the tire (16.795 inches) to find the number of rotations per second. This gives us approximately 3.93 rotations per second.
Therefore, when you have the new 5.35-inch tires and your speedometer reads 45 mph, your car is actually traveling at approximately 3.93 rotations per second.
Lastly, let's consider the scenario where you replace your tires with 3.75-inch tires and your speedometer reads 45 mph.
Step 5: Calculate the new linear velocity
Again, using the same steps as before, we find that the new tire has a radius of 1.875 inches (half of 3.75 inches). The circumference of the new tire is approximately 11.781 inches.
Dividing the linear velocity of 45 mph (66 inches/second) by the new circumference of the tire (11.781 inches), we find that the number of rotations per second is approximately 5.614 rotations per second.
Therefore, when you have the new 3.75-inch tires and your speedometer reads 45 mph, your car is actually traveling at approximately 5.614 rotations per second.
To know more about "Car's Speedometer":
https://brainly.com/question/5830082
#SPJ11
Given: AB = 10. 2 cm and BC = 3. 7 cm Find: The length of AC or AC
The length of AC is approximately 10.85 cm.
To find the length of AC, we can use the Pythagorean theorem.
According to the Pythagorean theorem, in a right triangle where c is the hypotenuse (the side opposite the right angle) and a and b are the other two sides, the relationship between the lengths of the sides is:
c^2 = a^2 + b^2
In this case, we can use AB as one of the legs of the right triangle and BC as the other leg, with AC being the hypotenuse. So we have:
AC^2 = AB^2 + BC^2
AC^2 = (10.2 cm)^2 + (3.7 cm)^2
AC^2 = 104.04 cm^2 + 13.69 cm^2
AC^2 = 117.73 cm^2
To find the length of AC, we take the square root of both sides:
AC = sqrt(117.73 cm^2)
AC ≈ 10.85 cm
Therefore, the length of AC is approximately 10.85 cm.
Learn more about length from
https://brainly.com/question/2217700
#SPJ11
Five families each fave threo sons and no daughters. Assuming boy and girl babies are equally tikely. What is the probablity of this event? The probabsity is (Type an integer of a simplified fraction)
The probability of five families each having three sons and no daughters is 1/32768. So, the probability of this event is 1/32768.
Given that there are five families, and each family has three sons and no daughters.
We have to find the probability of this event.
Let's solve this problem, We know that there are two genders, boy and girl.
Since a baby can be either a boy or a girl, there is a 1/2 chance of a family having a son or daughter.
The probability of having three sons in a row is 1/2 * 1/2 * 1/2 = 1/8
For all five families to have three sons, the probability is:
1/8 * 1/8 * 1/8 * 1/8 * 1/8 = (1/8)⁵
= 1/32768
Thus, the probability of five families each having three sons and no daughters is 1/32768.
So, the probability of this event is 1/32768.
To know more about probability visit:
https://brainly.com/question/31828911
#SPJ11
With the use of appropriate examples explain the difference between the conductivities of strong and weak electrolytes.
Electrolytes conduct electricity when dissolved in water or melted. Strong electrolytes, like NaCl, HCl, H2SO4, and KOH, dissociate completely into ions, resulting in higher conductivity. Weak electrolytes, like CH3COOH, NH3, and H2O, dissociate partially, resulting in lower conductivity.
Electrolytes are the compounds that conduct electricity when dissolved in water or melted. The conductivity of strong electrolytes is higher than that of weak electrolytes. A strong electrolyte dissociates completely into ions when dissolved in water, while a weak electrolyte dissociates only partially into ions.Strong electrolytes such as NaCl, HCl, H2SO4, KOH, etc., are compounds that completely dissociate into ions when dissolved in water. These ions carry the current and result in higher conductivity.
For example, if NaCl is dissolved in water, it will dissociate completely into Na+ and Cl- ions. The solution will have a high conductivity as the ions are highly mobile in the solution and carry the charge. Similarly, a concentrated solution of HCl will conduct electricity well.
The following is the chemical reaction that takes place when HCl is dissolved in water.
HCl → H+ + Cl-Weak electrolytes, on the other hand, are compounds that dissociate only partially into ions when dissolved in water. Examples of weak electrolytes include CH3COOH (acetic acid), NH3 (ammonia), and H2O (water). These electrolytes do not dissociate completely when dissolved in water. As a result, the conductivity is lower. For example, acetic acid in water will dissociate partially as shown below.CH3COOH → CH3COO- + H+
The solution will have a low conductivity because only a small number of ions are available to carry the charge.Hence, strong electrolytes dissociate completely into ions and conduct electricity well. In contrast, weak electrolytes dissociate partially into ions and conduct electricity poorly.
To know more about Electrolytes Visit:
https://brainly.com/question/32477009
#SPJ11
Thermally isolated gas CH4 is slowly compressed to a 3.000 times smaller volume and then isothermally, decompressed back to the initial volume. What would be the gas temperature in degrees Celsius after compression and decompression if its initial temperature is 100.00°C and initial pressure is 2.00 atm? Use classical expression for the gas specific heat.
The gas in question is CH4, which is methane. It is initially thermally isolated, meaning there is no heat exchange with the surroundings.
First, the gas is slowly compressed to a volume 3.000 times smaller than its initial volume. During this compression, the gas is still thermally isolated, so there is no heat exchange.
Next, the gas is decompressed isothermally, meaning the temperature remains constant during this process. The gas is returned to its initial volume.
To find the final temperature after compression and decompression, we can use the formula for the specific heat capacity of an ideal gas:
Q = nCΔT
Where:
Q is the heat transferred to the gas (or from the gas),
n is the number of moles of the gas,
C is the molar specific heat capacity of the gas at constant volume,
ΔT is the change in temperature.
Since the gas is thermally isolated, no heat is transferred during the compression and decompression processes. Therefore, Q = 0.
Since the volume is reduced by a factor of 3.000 during compression, the pressure will increase by the same factor according to Boyle's Law:
P1V1 = P2V2
Where:
P1 is the initial pressure,
V1 is the initial volume,
P2 is the final pressure,
V2 is the final volume.
Plugging in the given values:
P1 = 2.00 atm
V1 = 1 (initial volume, arbitrary unit)
P2 = ?
V2 = 1/3 (final volume)
2.00 atm * 1 = P2 * 1/3
P2 = 6.00 atm
Now, we can use the ideal gas law to find the number of moles of the gas:
PV = nRT
Where:
P is the pressure,
V is the volume,
n is the number of moles,
R is the ideal gas constant (0.0821 L·atm/(mol·K)),
T is the temperature in Kelvin.
Plugging in the values:
P = 6.00 atm
V = 1 (initial volume, arbitrary unit)
n = ?
R = 0.0821 L·atm/(mol·K)
T = 100.00°C + 273.15 = 373.15 K (initial temperature in Kelvin)
6.00 atm * 1 = n * 0.0821 L·atm/(mol·K) * 373.15 K
n = 0.145 mol
Since the compression and decompression processes are reversible, the number of moles of the gas remains constant.
Now, we can find the final temperature after decompression using the ideal gas law again:
P = 2.00 atm (initial pressure)
V = 1 (initial volume, arbitrary unit)
n = 0.145 mol
R = 0.0821 L·atm/(mol·K)
T = ?
2.00 atm * 1 = 0.145 mol * 0.0821 L·atm/(mol·K) * T
T = 13.74 K
Converting the temperature to degrees Celsius:
T = 13.74 K - 273.15 = -259.41°C
Therefore, the gas temperature after compression and decompression would be approximately -259.41°C.
Know more about heat exchange:
https://brainly.com/question/13039682
#SPJ11
For each problem, the available design formulas and tables from the lecture slides and the AISC manual can be used. Problem 1 Determine the distributed service load (30% DL including beam weight, 70%LL) that can be applied on a 50-ft long simply supported beam made of W24x62 A36 steel (Fy-36 ksi, E = 29,000 ksi). Lateral supports are placed at the midspan and at both ends of the beam.
The maximum distributed service load (30% DL including beam weight, 70%LL) that can be applied to the 50 ft long simply supported beam is 0.109 kip/ft.
How to find?The self-weight is equal to the weight of the beam per unit length multiplied by the length of the beam. Wt of W24x62 = 62 pounds per foot
The self-weight of the beam = 62 plf x 50ft
= 3100 lbs
Step 2
Next, find the allowable bending stress for A36 steel. The allowable bending stress for A36 steel is given by:
[tex]Fy / SF = 36 / 1.67[/tex]
= 21.56 ksi,
The maximum moment that can be applied to the beam is given by:
= ² / 8
Where w = the total load acting on the beam per unit length, including the beam's self-weight,
l = the length of the beam.
The distributed load that can be applied to the beam is given by:
[tex]W = 1.3 x (62 x 1 + q)[/tex]
= 80.6 q plf
Where 1 is the beam weight, q is the load factor.
L = 50 ft
The maximum moment that can be applied to the beam is
[tex] = (80.6q × 50²) / 8[/tex]
Step 4
Compute the maximum bending stress using the maximum moment and the beam's cross-sectional properties.
= /
Where is the section modulus of the beam.
The section modulus of the W24x62 beam is given in the AISC manual.
= 47.9 in³, Where in³ represents cubic inches.
The maximum bending stress is = /
Now that you have calculated the maximum bending stress, compare it with the allowable bending stress.
Step 5
If the maximum bending stress is less than the allowable bending stress, the beam can withstand the maximum moment calculated in step 3. ≤ , where is the allowable bending stress for A36 steel.
= (80.6q × 50²) / 8
= ×
= ( / ) ×
Therefore, / = ≤
= 21.56 ksi
For the maximum moment to be applied to the beam, the maximum bending stress must be less than or equal to the allowable bending stress.
Hence, solve for q as follows:
= (80.6q × 50²) / (8 × 47.9)
= × 8 × 47.9 / (80.6 × 50²)
Putting the values, we get
= 8 × 47.9 × 21.56 / (80.6 × 50²)
= 0.109 kip/ft
The maximum distributed service load (30% DL including beam weight, 70%LL) that can be applied to the 50 ft long simply supported beam is 0.109 kip/ft.
To know more on Service load visit:
https://brainly.com/question/32224700
#SPJ11
Is the following definition of perpendicular reversible? If yes, write it as a true biconditional.Two lines that intersect at right angles are perpendicular.
Yes, the definition of perpendicular is reversible. This can be written as a true biconditional as follows: Two lines are perpendicular if and only if they intersect at right angles.
If two lines intersect at right angles, then they are perpendicular, and conversely, if two lines are perpendicular, then they intersect at right angles. This can be written as a true biconditional as follows: Two lines are perpendicular if and only if they intersect at right angles.
Both parts of the biconditional statement are conditional statements. The first part is a conditional statement where the hypothesis is "two lines intersect at right angles," and the conclusion is "the lines are perpendicular." The second part is also a conditional statement where the hypothesis is "the lines are perpendicular," and the conclusion is "two lines intersect at right angles."
Since both parts of the biconditional statement are true, the statement itself is true. Therefore, we can say that the definition of perpendicular is reversible, and it can be expressed as a true biconditional statement.
For more such questions on true biconditional, click on:
https://brainly.com/question/27738859
#SPJ8
David and Helen Zhang are saving to buy a boat at the end of seven years. If the boat costs $27,000 and they can earn 11% a year on their savings, how much do they need to put aside at the end of years 1 through 7?
David and Helen need to put aside approximately $13,861 at the end of each year for seven years in order to save $27,000 to buy the boat.
To calculate how much David and Helen Zhang need to put aside at the end of each year for seven years, we can use the concept of compound interest.
Compound interest is the interest earned on both the initial amount and any accumulated interest from previous periods. In this case, David and Helen want to save $27,000 in seven years, earning 11% interest per year.
To find out how much they need to put aside at the end of each year, we can divide the total amount needed by the future value factor for an ordinary annuity.
The future value factor is calculated using the formula:
Future Value Factor = (1 + interest rate)^number of periods
In this case, the interest rate is 11% or 0.11, and the number of periods is seven (as they want to save for seven years). Plugging these values into the formula, we get:
Future Value Factor = (1 + 0.11)^7
Calculating this, we find that the future value factor is approximately 1.949.
Next, we divide the total amount needed by the future value factor to find out how much David and Helen need to put aside at the end of each year:
Amount to put aside = $27,000 / 1.949
= approximately $13,861
Learn more about compound interest: https://brainly.com/question/3989769
#SPJ11
Is 2/3y=6 subtraction property of equality
No, the equation 2/3y = 6 does not involve the subtraction property of equality. The subtraction property of equality states that if you subtract the same quantity from both sides of an equation, the equality still holds true. However, in the given equation, there is no subtraction involved.
The equation 2/3y = 6 is a linear equation in which the variable y is multiplied by the fraction 2/3. To solve this equation, we need to isolate the variable y on one side of the equation.
To do that, we can multiply both sides of the equation by the reciprocal of 2/3, which is 3/2. This operation is an application of the multiplicative property of equality.
By multiplying both sides of the equation by 3/2, we get:
(2/3y) * (3/2) = 6 * (3/2)
Simplifying this expression, we have:
(2/3) * (3/2) * y = 9
The fractions (2/3) and (3/2) cancel out, leaving us with:
1 * y = 9
This simplifies to:
y = 9
Therefore, the solution to the equation 2/3y = 6 is y = 9. The process of solving this equation did not involve the subtraction property of equality.
For more questions on variable, click on:
https://brainly.com/question/28248724
#SPJ8
The assembly of pipes consists of galvanized steel pipe AB and BC connected together at B using a reducing coupling and rigidly attached to the wall at A. The bigger pipe AB is 1 m long, has inner diameter 17mm and outer diameter 20 mm. The smaller pipe BC is 0.50 m long, has inner diameter 15 mm and outer diameter 13 mm. Use G = 83 GPa. Find the torque that will twist at C a total of 5.277 degrees. Select one: O a. 21 kNm O b. 26 kNm O c. 28 kNm O d. 24 kNm
The torque required to twist point C of the pipe assembly by a total of 5.277 degrees is approximately 28 kNm.
To find the torque required to twist point C of the pipe assembly, we need to consider the properties of the pipes and their behavior under torsional loading.
Calculate the polar moments of inertia for both pipes:
The polar moment of inertia for a pipe can be calculated using the formula:
[tex]J = (π/32) * (D^4 - d^4)[/tex]
where D is the outer diameter and d is the inner diameter of the pipe.
Calculate the polar moments of inertia for pipes AB and BC using their respective dimensions.
Determine the torsional rigidity for each pipe:
The torsional rigidity (GJ) of a pipe can be calculated using the formula:
[tex]GJ = G * J[/tex]
where G is the shear modulus of the material and J is the polar moment of inertia.
Calculate the torsional rigidity for pipes AB and BC using the given shear modulus (G) and the previously calculated polar moments of inertia.
Calculate the torque required for the desired twist angle:
The torque required to twist a pipe can be calculated using the formula:
[tex]T = (θ * L * GJ) / (2π)[/tex]
where T is the torque, θ is the twist angle in radians, L is the length of the pipe, and GJ is the torsional rigidity.
Substitute the values of the twist angle (5.277 degrees converted to radians), length of pipe BC (0.50 m), and the torsional rigidity of pipe BC into the formula to calculate the torque.
By performing the calculations, we find that the torque required to twist point C of the pipe assembly by a total of 5.277 degrees is approximately 28 kNm.
To Know more about polar moments visit:
https://brainly.com/question/33381705
#SPJ11
A 2m diameter spherical chamber has an internal pressure of 17 kPa. If the chamber has a wall thickness of 144 mm, what is the stress in the walls of the chamber?
The stress in the walls of the spherical chamber is 593.75 kPa.
The stress in the walls of the spherical chamber can be calculated using the following formula:
σ = pr / t
Where,σ is the stress in the walls of the spherical chamber p is the internal pressure of the spherical chamber,
17 kPar is the radius of the spherical chamber, which is half the diameter, 1 mt is the thickness of the walls of the spherical chamber, 144 mm = 0.144 m
Substituting the given values in the above equation, we get:
σ = (17 × 10³ × 1) / (2 × 0.144)
σ = 593.75 kPa
Thus, the stress in the walls of the chamber is 593.75 kPa. Therefore, the answer is 593.75 kPa.
: The stress in the walls of the spherical chamber is 593.75 kPa.
To know more about radius visit:
brainly.com/question/24051825
#SPJ11
Select ALL the quadratic functions that open UP
f(x) = -x² + 2x + 9
f(x) = 7x² - 8x - 53
g(x) = -2(x+3)² – 1
h(x) = 4(x-2)(x + 9)
f(x) = x² + 4x − 1
Answer:
f(x) and g(x) are the quadratic functions that open UP.
The pH of an aqueous solution of 7.77x10^-2 M hydrosulfuric acid, H₂S (aq) is ?
H₂S is a binary acid that reacts with water, forming an oxonium ion (H3O+). The acid dissociation constant expression (Ka) is used to calculate pH. The hydrogen ion concentration is determined by solving for x, resulting in a pH of 4.12.
The given chemical compound is H₂S. This is a binary acid; H₂S, therefore it should be reacted with water. When a binary acid is reacted with water, it donates a proton to the water molecule, forming an oxonium ion (H3O+). In H₂S(aq), one hydrogen atom will be transferred from H₂S to a water molecule.
In the aqueous solution, the balance between the H₂S acid and its conjugate base HS- will be shifted. We'll need the acid dissociation constant expression (Ka) for H₂S to calculate pH. The acid dissociation constant, Ka is defined as [H+][HS-]/[H2S].Ka = [H+][HS-]/[H2S].
Assuming that x is the amount of dissociated H₂S, then the H+ is x and the amount of HS- will also be x. The amount of undissociated H₂S is equal to the original H₂S concentration minus x (7.77x10-2 - x).
Substitute these values into the Ka expression: Ka = x2/(7.77x10-2 - x).
At equilibrium, the degree of dissociation is the same as the hydrogen ion concentration:[H+] = [HS-] = x.
The expression above can be used to calculate [H+].Ka = x2/(7.77x10-2 - x)5.62x10-8 = x2/(7.77x10-2 - x)
By solving for x, we can determine the hydrogen ion concentration and then calculate the pH. x = 7.51x10-5 (from calculator)Now we have the [H+] and can calculate the pH:
pH = -log[H+]pH
= -log(7.51x10-5)pH
= 4.12
The pH of the given aqueous solution of 7.77x10^-2 M hydro sulfuric acid, H₂S (aq) is 4.12.
To know more about binary acid Visit:
https://brainly.com/question/12156568
#SPJ11
6) When octane gas (CsH18) combusts with oxygen gas, the products are carbon dioxide gas and water vapor. A) Write and balance the equation using appropriate states. B) When 500.0-grams of octane react with 1000.-grams of oxygen gas, what is the limiting reactant? C) When 60.0-grams of octane react with 60.0-grams of oxygen gas, what is the amount (moles) of carbon dioxide formed. D) When 60.0-grams of octane react with 60.0-grams of oxygen gas, how many grams of excess reactant are leftover?
The balanced equation for the combustion of octane is: 2 C8H18 (g) + 25 O2 (g) → 16 CO2 (g) + 18 H2O (g).The limiting reactant can be determined by comparing the moles of octane and oxygen gas to their stoichiometric ratio.To find the amount of carbon dioxide formed when 60.0 grams of octane reacts with 60.0 grams of oxygen gas, we convert the masses to moles and use the balanced equation's mole ratio.To calculate the grams of excess reactant leftover when 60.0 grams of octane reacts with 60.0 grams of oxygen gas, we identify the limiting reactant and subtract the consumed mass from the initial mass of the excess reactant.
A) The balanced equation for the combustion of octane gas (C8H18) with oxygen gas (O2) to form carbon dioxide gas (CO2) and water vapor (H2O) is:
2 C8H18 (g) + 25 O2 (g) → 16 CO2 (g) + 18 H2O (g)
B) The limiting reactant is determined by comparing the moles of octane and oxygen gas to their stoichiometric ratio. By calculating the moles of each reactant and comparing them to the coefficients in the balanced equation, we can identify which reactant is consumed completely, thus limiting the reaction.
C) To determine the amount of carbon dioxide formed when 60.0 grams of octane reacts with 60.0 grams of oxygen gas, we convert the given masses to moles using the molar masses of octane and oxygen gas. Then, we use the mole ratio from the balanced equation to find the moles of carbon dioxide formed.
D) When 60.0 grams of octane reacts with 60.0 grams of oxygen gas, we first identify the limiting reactant. Then, we calculate the moles of the excess reactant consumed based on the stoichiometry of the balanced equation. Finally, we find the grams of the leftover excess reactant by subtracting the mass consumed from the initial mass.
Know more about combustion here:
https://brainly.com/question/31123826
#SPJ11
Undisturbed specimens of the gouge material filling a rock joint
was tested in the laboratory and the cohesion and friction angles
are determined as 5 MPa and 35°, respectively. If the minor principal
stress at the joint is 2 MPa, determine the value of σ1 that is
required to cause shear failure along the joint that is inclined to
the major principal plane by (a) 45°, (b) 55° and (c) 65°.
The value of σ1 that is required to cause shear failure along the joint that is inclined to the major principal plane by 45°, 55° and 65° are 6.51 MPa, 8.28 MPa and 10.44 MPa, respectively.
How to calculate the values of σ1To calculate the value of σ1, use the Mohr-Coulomb failure criterion
τf = c + σn tan φ
where:
τf = shear stress required to cause failure
c = cohesion = 5 MPa
σn = normal stress on the joint
φ = friction angle = 35°
When the joint is inclined to the major principal plane by 45°, the major principal stress (σ1) is equal to the maximum principal stress.
The intermediate principal stress (σ2) is equal to the minor principal stress (σ3) because the joint is inclined at 45° to the major principal plane.
Therefore:
σ1 = σn + σ3
= σn + 2 MPa
The angle between the joint and the plane of σ1 is 45°.
τf = 5 MPa + σn tan 35° = σ1 sin 45° tan 35°
Substitute σ1
5 MPa + σn tan 35° = (σn + 2 MPa) sin 45° tan 35°
By solving for σn
σn ≈ 4.51 MPa
Therefore, the value of σ1 required to cause shear failure along the joint that is inclined to the major principal plane by 45° is:
σ1 ≈ 6.51 MPa
Follow the steps above to calculate for 55°, and 65°.
Learn more on principal stress on https://brainly.com/question/30089382
#SPJ4
PLEASE HELP WILL GIVE BRAINELEST
Use the midpoint formula to
select the midpoint of line
segment EQ.
E(-2,5)
Q(-3,-6)
Y
X
The midpoint of the line is (-2.5, -0.5)
How to calculate the midpoint of the lineFrom the question, we have the following parameters that can be used in our computation:
E(-2,5) and Q(-3,-6)
The midpoint of the line is calculated as
Midpoint = 1/2(E + Q)
Substitute the known values in the above equation, so, we have the following representation
Midpoint = 1/2(-2 - 3, 5 - 6)
Evaluate
Midpoint = (-2.5, -0.5)
Hence, the midpoint of the line is (-2.5, -0.5)
Read more about midpoint at
https://brainly.com/question/28462165
#SPJ1
Write the balanced chemical reaction for the reaction between magnesium chloride reacts and steam. Then calculate how many liters of hydrochloric acid is produced when 1 ton of magnesium chloride reacts with steam.
The balanced chemical reaction between magnesium chloride (MgCl₂) and steam (H₂O) is MgCl₂ + 2H₂O → Mg(OH)₂ + 2HCl If 1 ton of magnesium chloride reacts with steam, approximately 469,582.94 liters of hydrochloric acid are produced.
The balanced chemical reaction between magnesium chloride (MgCl₂) and steam (H₂O) can be represented as follows:
MgCl₂ + 2H₂O → Mg(OH)₂ + 2HCl
In this reaction, magnesium chloride reacts with steam to form magnesium hydroxide and hydrochloric acid.
To calculate the number of liters of hydrochloric acid produced when 1 ton (1000 kg) of magnesium chloride reacts, we need to determine the stoichiometry of the reaction.
From the balanced equation, we can see that 1 mole of magnesium chloride reacts to produce 2 moles of hydrochloric acid. The molar mass of magnesium chloride (MgCl₂) is 95.211 g/mol.
First, calculate the number of moles of magnesium chloride in 1 ton:
Number of moles of MgCl₂ = (1000 kg) / (95.211 g/mol)
Next, use the stoichiometric ratio to calculate the number of moles of hydrochloric acid produced:
Number of moles of HCl = 2 × Number of moles of MgCl₂
Finally, convert the number of moles of hydrochloric acid to liters:
Volume of HCl = (Number of moles of HCl) × (22.4 L/mol)
Performing the calculations, we have:
Number of moles of MgCl₂ = (1000 kg) / (95.211 g/mol) ≈ 10492.14 mol
Number of moles of HCl = 2 × 10492.14 mol ≈ 20984.29 mol
Volume of HCl = 20984.29 mol × 22.4 L/mol ≈ 469582.94 L
Therefore, when 1 ton of magnesium chloride reacts with steam, approximately 469,582.94 liters of hydrochloric acid are produced.
Learn more about chemical reaction at https://brainly.com/question/23728581
#SPJ11
Some mechanical applications such as for cams, gears etc., require a hard wear resistant surface and a relatively soft, tough and shock resistant core. In order to achieve such a unique property suggest any metallurgy technique that is appropriate, also explain the method in detail.
It's worth noting that there are other case hardening methods as well, such as nitriding, carbonitriding, and induction hardening, which offer different advantages and can be selected based on specific material requirements and application needs.
One metallurgy technique that can be used to achieve a hard wear-resistant surface and a relatively soft, tough, and shock-resistant core is called "case hardening" or "surface hardening." Case hardening involves altering the surface properties of a metal while maintaining the desired mechanical properties in the core.
One commonly used method of case hardening is "carburizing" or "gas carburizing." This process involves introducing carbon into the surface layer of the metal, creating a high-carbon concentration at the surface while maintaining a lower carbon concentration in the core.
Here is a detailed explanation of the carburizing process:
Preparation: The metal component to be case hardened is cleaned and preheated to remove any contaminants.
Carburizing: The preheated component is placed in a furnace or a sealed chamber containing a carbon-rich atmosphere, usually composed of hydrocarbon gases such as methane, propane, or natural gas. The temperature is typically maintained between 850°C to 950°C (1562°F to 1742°F) to allow carbon diffusion.
Diffusion: Carbon atoms from the gas atmosphere diffuse into the metal's surface due to the concentration gradient. The carbon atoms diffuse into the lattice structure of the metal, occupying interstitial sites between the metal atoms.
Case Formation: The carbon concentration increases with time, forming a high-carbon layer at the surface. This layer is typically several hundred micrometers thick, depending on the desired depth of the hardened layer.
Quenching: Once the desired carbon diffusion and case formation are achieved, the component is rapidly cooled or quenched to room temperature. Quenching can be done using different media such as oil, water, or air, depending on the material and desired properties.
Tempering: After quenching, the component is often subjected to a tempering process. Tempering involves reheating the component to a specific temperature below the critical point, followed by controlled cooling. This step helps reduce internal stresses and improves the toughness and ductility of the core.
The carburizing process allows the formation of a hardened case with high wear resistance due to the increased carbon content at the surface. At the same time, the core remains relatively soft, tough, and shock-resistant due to the lower carbon concentration. The combination of the hardened surface and a resilient core provides the desired mechanical properties for applications such as cams, gears, and other components subjected to high contact and wear loads.
It's worth noting that there are other case hardening methods as well, such as nitriding, carbonitriding, and induction hardening, which offer different advantages and can be selected based on specific material requirements and application needs.
To know more about metallurgy visit
https://brainly.com/question/30203424
#SPJ11
In this problem, p is in dollars and x is the number of units. Find the producer's surplus at market equlibrium for a product if its demand function is p=100−x^2 and its supply function is p=x^2+10x+72. (Round your answer to the nearest cent.) 3
The producer's surplus at market equilibrium for the product is $8.
To find the producer's surplus at market equilibrium, we first need to find the equilibrium point where the demand and supply functions intersect.
Given the demand function: p = 100 - x^2
And the supply function: p = x^2 + 10x + 72
At equilibrium, the quantity demanded equals the quantity supplied. Therefore, we can set the demand and supply functions equal to each other:
100 - x^2 = x^2 + 10x + 72
Rearranging and simplifying the equation, we get:
2x^2 + 10x - 28 = 0
To solve this quadratic equation, we can use factoring, completing the square, or the quadratic formula. In this case, the equation can be factored as follows:
(2x - 4)(x + 7) = 0
This gives two possible solutions: x = 2/2 = 1 and x = -7. However, we discard the negative value since we are dealing with quantities of units.
Therefore, the equilibrium point is x = 1.
To find the corresponding price at equilibrium, we can substitute this value back into either the demand or supply function. Let's use the demand function:
p = 100 - (1)^2
p = 100 - 1
p = 99
So, at the equilibrium point, the price is $99 per unit.
To calculate the producer's surplus, we need to find the area between the supply curve and the equilibrium price line.
The producer's surplus is the area above the supply curve and below the equilibrium price line.
The area of a triangle is given by the formula: (1/2) * base * height
The base of the triangle is the quantity, which is x = 1.
The height of the triangle is the difference between the equilibrium price and the supply price at x = 1, which is (99 - (1^2 + 10*1 + 72)) = 99 - 83 = 16.
Therefore, the producer's surplus at market equilibrium is:
Producer's Surplus = (1/2) * 1 * 16 = 8
Rounding to the nearest cent, the producer's surplus at market equilibrium for the product is $8.
Learn more about market equilibrium from the given link
https://brainly.com/question/29618306
#SPJ11
Determine the first three nonzero terms in the Taylor polynomial approximation for the given initial value problem. 3x′′+3tx=0;x(0)=1,x′(0)=0 The Taylor approximation to three nonzero terms is x(t)=+….
The first three nonzero terms in the Taylor polynomial approximation for the given initial value problem 3x′′ + 3tx = 0, with x(0) = 1 and x′(0) = 0, are x(t) = 1.
To find the Taylor polynomial approximation for the given initial value problem, we can use the Taylor series expansion of the solution function.
Let's start by finding the derivatives of the solution function.
Given: 3x′′ + 3tx = 0, with initial conditions x(0) = 1 and x′(0) = 0.
Differentiating the equation with respect to t, we get:
3x′′ + 3tx = 0
Differentiating again, we get:
3x′′′ + 3x + 3t(x′) = 0
Now, let's substitute the initial conditions into the equations.
At t = 0:
3x′′(0) + 0 = 0
3x′′(0) = 0
At t = 0:
3x′′′(0) + 3x(0) + 0 = 0
3x(0) = 0
From the initial conditions, we find that x′′(0) = 0 and x(0) = 1.
Now, let's use the Taylor series expansion of the solution function centered at t = 0:
x(t) = x(0) + x′(0)t + (x′′(0)/2!)t^2 + (x′′′(0)/3!)t^3 + ...
Substituting the initial conditions into the Taylor series expansion, we get:
x(t) = 1 + 0 + (0/2!)t^2 + (0/3!)t^3 + ...
Simplifying, we find that the first three nonzero terms in the Taylor polynomial approximation are:
x(t) = 1 + 0t + 0 + ...
Therefore, the Taylor approximation to three nonzero terms is x(t) = 1.
In summary, the first three nonzero terms in the Taylor polynomial approximation for the given initial value problem 3x′′ + 3tx = 0, with x(0) = 1 and x′(0) = 0, are x(t) = 1.
Learn more about Taylor polynomial from the given link
https://brainly.com/question/2533683
#SPJ11
Let P,Q ve proporitional variables. Definie a junctor P∣Q e.g. by giving a truth table or a sutable formula Q, so that you can find proporitionally equivalert formulas for IP and P∧Q that ouly use the conrective I use. Iustify this as well, e.g. by spec ifying switable truth tables.
The junctor P∣Q can be defined as "if P is true, then Q is true; otherwise, P can be false."
How can we show that P∣Q is propositionally equivalent to IP and P∧Q?To show that P∣Q is propositionally equivalent to IP (implication) and P∧Q (conjunction), we can construct truth tables for all three expressions. Let's denote "T" for true and "F" for false.
1. Truth table for P∣Q:
| P | Q | P∣Q |
|---|---|----|
| T | T | T |
| T | F | F |
| F | T | T |
| F | F | T |
2. Truth table for IP (Implication):
| P | Q | IP |
|---|---|----|
| T | T | T |
| T | F | F |
| F | T | T |
| F | F | T |
3. Truth table for P∧Q (Conjunction):
| P | Q | P∧Q |
|---|---|-----|
| T | T | T |
| T | F | F |
| F | T | F |
| F | F | F |
By comparing the truth tables, we can see that P∣Q and IP have identical truth values for all combinations of P and Q. Similarly, P∣Q and P∧Q have identical truth values for all combinations of P and Q as well. Therefore, P∣Q is propositionally equivalent to both IP and P∧Q.
Learn more about junctor
brainly.com/question/21542732
#SPJ11
I NEED HELP ASAP MY GRADE IS GOING TO DROP IF I DONT GET THE ANSWER PLS HELP The vertices of a rectangle are plotted.
A graph with both the x and y axes starting at negative 8, with tick marks every one unit up to 8. The points negative 4 comma 4, 6 comma 4, negative 4 comma negative 5, and 6 comma negative 5 are each labeled.
What is the area of the rectangle?
19 square units
38 square units
90 square units
100 square units
The length of the base and the height using the given coordinates of the vertices and the area of the rectangle is C. 90 square units.
To find the area of a rectangle, we multiply the length of one side (base) by the length of the other side (height). In this case, we can determine the length of the base and the height using the given coordinates of the vertices.
The given points are: (-4, 4), (6, 4), (-4, -5), and (6, -5).
The length of the base can be found by subtracting the x-coordinate of one point from the x-coordinate of another point. In this case, the x-coordinate of (-4, 4) and (6, 4) is the same, which means the base has a length of 6 - (-4) = 10 units.
The height can be determined by subtracting the y-coordinate of one point from the y-coordinate of another point. Here, the y-coordinate of (-4, 4) and (-4, -5) is the same, so the height is 4 - (-5) = 9 units.
To find the area, we multiply the base length (10) by the height (9), resulting in an area of 10 * 9 = 90 square units. Therefore, Option C is correct.
The question was incomplete. find the full content below:
I NEED HELP ASAP MY GRADE IS GOING TO DROP IF I DONT GET THE ANSWER PLS HELP The vertices of a rectangle are plotted.
A graph with both the x and y axes starting at negative 8, with tick marks every one unit up to 8. The points negative 4 comma 4, 6 comma 4, negative 4 comma negative 5, and 6 comma negative 5 are each labeled.
What is the area of the rectangle?
A. 19 square units
B. 38 square units
C. 90 square units
D. 100 square units
Know more about area of the rectangle here:
https://brainly.com/question/2607596
#SPJ8
Answer:
C) 90 square units
Step-by-step explanation:
Given vertices of a plotted rectangle:
(-4, 4)(6, 4)(-4, -5)(6, -5)The width of the rectangle is the difference in y-values of the vertices. Therefore, the width is:
[tex]\begin{aligned} \sf Width &= 4 - (-5) \\&= 4 + 5 \\&= 9 \; \sf units \end{aligned}[/tex]
The length of the rectangle is the difference in x-values of the vertices. Therefore, the length is:
[tex]\begin{aligned} \sf Length &= 6 - (-4) \\&= 6 + 4 \\&= 10 \; \sf units \end{aligned}[/tex]
The area of a rectangle is the product of its width and length. Therefore, the area of the plotted rectangle is:
[tex]\begin{aligned} \sf Area &= 9 \times 10\\&=90 \; \sf square\;units \end{aligned}[/tex]
Therefore, the area of the rectangle is 90 square units.
A student reacted 4.00 x 10^23 molecules of nitrogen with 1.00 x 10^24 molecules of hydrogen.
A) How many grams of ammonia gas will be produced?
B) Which reactant is the limiting reactant?
C) How many molecules of excess reactant remain?
A) The amount in grams of ammonia gas that will be produced is approximately 22.62 grams.
B) The limiting reactant is nitrogen.
C) The number of molecules of excess reactant remaining is approximately 7.35 x 10²³ molecules.
A) To find the grams of ammonia gas produced, we need to determine the limiting reactant and use stoichiometry. First, let's write the balanced equation for the reaction:
N₂ + 3H₂ -> 2NH₃
From the balanced equation, we can see that 1 mole of nitrogen (N₂) reacts with 3 moles of hydrogen (H₂) to produce 2 moles of ammonia (NH₃).
Given that the student reacted 4.00 x 10²³ molecules of nitrogen and 1.00 x 10²⁴ molecules of hydrogen, we need to convert these quantities to moles.
To convert the number of molecules to moles, we divide by Avogadro's number (6.022 x 10²³ molecules/mol).
For nitrogen: (4.00 x 10²³ molecules) / (6.022 x 10²³ molecules/mol) = 0.665 mol
For hydrogen: (1.00 x 10²⁴ molecules) / (6.022 x 10²³ molecules/mol) = 1.66 mol
Next, we compare the moles of nitrogen and hydrogen to determine the limiting reactant. The reactant that is completely consumed is the limiting reactant.
Since the ratio of nitrogen to hydrogen in the balanced equation is 1:3, we can see that we have excess hydrogen. This means nitrogen is the limiting reactant.
Now, using stoichiometry, we can calculate the moles of ammonia produced from the limiting reactant (nitrogen):
Moles of ammonia = Moles of nitrogen x (2 moles of ammonia / 1 mole of nitrogen)
= 0.665 mol x (2 mol / 1 mol)
= 1.33 mol
Finally, to find the grams of ammonia produced, we use the molar mass of ammonia (17.03 g/mol):
Grams of ammonia = Moles of ammonia x Molar mass of ammonia
= 1.33 mol x 17.03 g/mol
= 22.62 g
Therefore, approximately 22.62 grams of ammonia gas will be produced.
B) The limiting reactant is nitrogen because it is completely consumed in the reaction, while hydrogen is in excess.
C) Since hydrogen is the excess reactant, we need to calculate the number of molecules of hydrogen remaining.
Moles of hydrogen remaining = Moles of hydrogen - Moles of hydrogen used for reaction
= 1.66 mol - (1.33 mol / 3)
= 1.22 mol
To convert moles back to molecules, we multiply by Avogadro's number:
Molecules of hydrogen remaining = Moles of hydrogen remaining x Avogadro's number
= 1.22 mol x 6.022 x 10²³ molecules/mol
= 7.35 x 10²³ molecules
Approximately 7.35 x 10²³ molecules of hydrogen remain as excess reactant.
Learn more about limiting reactant here: https://brainly.com/question/26905271
#SPJ11
Which equation represnys the verticalline passing through(14,-16)?
The equation representing a vertical line passing through the point (14, -16) can be expressed in the form of x = a, where 'a' is the x-coordinate of the point.
In this case, the x-coordinate of the given point is 14. Hence, the equation of the vertical line passing through (14, -16) is:
x = 14
This equation indicates that the x-coordinate of any point lying on this line will always be 14, while the y-coordinate can take any value. In other words, the line is parallel to the y-axis and extends infinitely in both the positive and negative y-directions.
By substituting any value for y, you will find that the x-coordinate of that point is always 14, confirming that it lies on the vertical line passing through (14, -16). It's important to note that since this is a vertical line, the slope of the line is undefined, as vertical lines have no defined slope.
Learn more about vertical here
https://brainly.com/question/29182548
#SPJ11
3-11. What are the main features of RCC gravity dams?
RCC gravity dams have become a popular choice for constructing water storage dams, and they are also used in the construction of hydroelectric dams.
RCC gravity dams have several features that distinguish them from other kinds of dams, including the following:
1. RCC gravity dams are constructed using high-strength roller-compacted concrete.
2. The purpose of an RCC gravity dam is to withstand water pressure while remaining securely anchored to the bedrock.
3. They have a low-cost of construction, are simple to construct, and can be completed quickly.
4. An RCC gravity dam is composed of multiple blocks of concrete that are constructed to fit together perfectly.
5. RCC gravity dams have a broad base, allowing them to support massive amounts of water pressure.
6. They can be constructed in a variety of sizes to accommodate various dam heights and widths.
7. As compared to conventional concrete dams, RCC gravity dams consume less cement.
As a result, RCC gravity dams have become a popular choice for constructing water storage dams, and they are also used in the construction of hydroelectric dams.
To know more about RCC gravity dams, click here
https://brainly.com/question/31843367
#SPJ11
I think I know the steps to Completing the Square (quadratics) but I'm not entirely sure. Please tell me if these steps are correct, and if they aren't, please tell me what is incorrect about them:
1. Separate the constant term from the variables
2. Factor out the coefficient of the x² term
3. Divide the middle term by the leading coefficient, then square the result
4. Simplify by combining like terms
5. Factor the perfect square trinomial formed on the left side
6. Divide both the left and right side of the equation by 2
7. Do inverse operations to remove the squared sign and its effects
8. Solve remaining equation for x
1. Separate the constant term from the variables.
2. Divide the middle term by the leading coefficient, then square the result.
3. Simplify by combining like terms.
4. Factor the perfect square trinomial formed on the left side.
5. Divide both sides of the equation by 2.
6. Take the square root of both sides to remove the squared term.
7. Solve the remaining equation for x.
8. Depending on the equation, you may need to perform additional algebraic manipulations to isolate x
The steps you've provided are mostly correct for completing the square to solve a quadratic equation. However, there are a few inaccuracies that I will address and clarify:
1. Separate the constant term from the variables: This step involves moving the constant term to the other side of the equation, so that the equation is in the form "ax² + bx + c = 0." The variables (x) should remain on one side, and the constant term (c) on the other side.
2. Factor out the coefficient of the x² term: This step is unnecessary when completing the square. The coefficient of the x² term will be used in subsequent steps, but there's no need to factor it out at this stage.
3. Divide the middle term by the leading coefficient, then square the result: This step is correct. The middle term (bx) should be divided by the coefficient of the x² term (a), and the result squared. This value will be used to complete the square.
4. Simplify by combining like terms: This step is also correct. After dividing and squaring the middle term, you should simplify the expression by combining like terms.
5. Factor the perfect square trinomial formed on the left side: This step is crucial. The simplified expression obtained in the previous step should be written as a perfect square trinomial. This can be done by factoring the trinomial into a squared binomial.
6. Divide both the left and right side of the equation by 2: This step is necessary to isolate the squared binomial on the left side of the equation. Dividing both sides by 2 ensures that the coefficient of the squared binomial is 1.
7. Do inverse operations to remove the squared sign and its effects: This step involves taking the square root of both sides of the equation. By doing this, the squared binomial is removed, and you obtain a simpler equation.
8. Solve the remaining equation for x: This final step involves solving the simplified equation for x. Depending on the equation, you may need to perform additional algebraic manipulations to isolate x.
For more such questions on variables visit:
https://brainly.com/question/25223322
#SPJ8
Describe all values of x that satisfy sinx<−1 /2on the interval [0,2π].
To find the values of x that satisfy sinx < -1/2 on the interval [0, 2π], we can use the inverse sine function, denoted as sin⁻¹. This will give us the principal angle between -π/2 and π/2 whose sine is equal to the given expression.sin⁻¹(-1/2) = -π/6This tells us that the sine of -π/6 is equal to -1/2.
We can use this to find all other angles whose sine is equal to -1/2 by adding integer multiples of 2π to the principal angle.-π/6 + 2πk, where k is an integer, will give us all angles between 0 and 2π whose sine is equal to -1/2. So we can set up the inequality as follows:-π/6 + 2πk < x < π + π/6 + 2πk. The values of x that satisfy sinx < -1/2 on the interval [0, 2π] are given by the inequality -π/6 + 2πk < x < π + π/6 + 2πk, where k is an integer. This means that we can find all angles between 0 and 2π whose sine is equal to -1/2 by adding integer multiples of 2π to the principal angle, -π/6. We can simplify the inequality as follows:11π/6 + 2πk < x < 13π/6 + 2πkThis tells us that there are two intervals of angles between 0 and 2π whose sine is equal to -1/2: one between -5π/6 and -π/6, and the other between 7π/6 and 11π/6. We can write this as follows:x ∈ [-5π/6, -π/6] ∪ [7π/6, 11π/6]
The values of x that satisfy sinx < -1/2 on the interval [0, 2π] are given by the inequality -π/6 + 2πk < x < π + π/6 + 2πk, where k is an integer. We can simplify this inequality to get x ∈ [-5π/6, -π/6] ∪ [7π/6, 11π/6].
To learn more about inverse sine function visit:
brainly.com/question/24160092
#SPJ11
Primary sedimentation tank is mainly designed to remove total suspended solids (TSS). Coagulants are sometimes added in the sedimentation tank to enhance the TSS removal. Assuming the sewage treatment plant of 15,000 m³/day contains initial TSS concentration of 300 mg/L. With TSS removal without using any coagulant achieve 55% and with the addition of ferric chloride achieving 88% TSS removal, determine the total sludge that can be removed from the sedimentation tank without using any coagulantand using ferric chloride as a coagulant for high TSS removal. Given: Ferric Chloride = FeCl3, MW = 162.2; Fe(OH)3, MW = 106.87; Calcium bicarbonate Ca(HCO3)2, MW = 162.11. Typical addition of ferric chloride = 40 kg per 1000 m³ wastewater. 2FeCl₂ +3Ca(HCO3)₂ 2Fe(OH), +3CaCl₂ +6CO₂ [Marks: 5]
In the given scenario, the primary sedimentation tank is used to remove total suspended solids (TSS) from the sewage. The initial TSS concentration is 300 mg/L.
First, let's determine the total sludge that can be removed from the sedimentation tank without using any coagulant:
- TSS removal without coagulant achieves 55%. This means that 55% of the TSS will be removed, while the remaining 45% will remain in the sewage.
- The sewage treatment plant processes 15,000 m³/day of sewage.
- The initial TSS concentration is 300 mg/L.
To calculate the total sludge that can be removed without using any coagulant, we can use the following equation:
Total sludge removed without coagulant = (TSS removal without coagulant) * (Sewage flow rate) * (Initial TSS concentration)
Total sludge removed without coagulant = 0.55 * 15,000 m³/day * 300 mg/L
By performing the calculation, we find that the total sludge that can be removed without using any coagulant is 2,475,000 mg/day or 2,475 kg/day.
Now, let's determine the total sludge that can be removed from the sedimentation tank using ferric chloride as a coagulant for high TSS removal:
- TSS removal with the addition of ferric chloride achieves 88%.
- Typical addition of ferric chloride is 40 kg per 1000 m³ of wastewater.
- The sewage treatment plant processes 15,000 m³/day of sewage.
To calculate the total sludge that can be removed using ferric chloride as a coagulant, we can use the following equation:
Total sludge removed with ferric chloride = (TSS removal with ferric chloride) * (Sewage flow rate) * (Initial TSS concentration)
Total sludge removed with ferric chloride = 0.88 * 15,000 m³/day * 300 mg/L
By performing the calculation, we find that the total sludge that can be removed using ferric chloride as a coagulant is 3,960,000 mg/day or 3,960 kg/day.
In conclusion, without using any coagulant, the total sludge that can be removed from the sedimentation tank is 2,475 kg/day. However, by using ferric chloride as a coagulant, the total sludge that can be removed increases to 3,960 kg/day.
learn more about TSS on
https://brainly.com/question/2141225
#SPJ11
Consider the peptides Cys-Ser-Ala-Ile-GIn-Asn-Lys and Gln-Ser-Cys-Lys-Asn-Ile-Ala. How do these two peptides differ? a.The two peptides have different isoelectric points. b.The two peptides differ in amino acid sequence. c.The two peptides have different titration curves. d.The two peptides have different compositions.
Option b is the correct answer: The two peptides differ in amino acid sequence.
The two peptides, Cys-Ser-Ala-Ile-Gln-Asn-Lys and Gln-Ser-Cys-Lys-Asn-Ile-Ala, differ in their amino acid sequence.
Peptides are made up of amino acids linked together by peptide bonds. In this case, the two peptides have different sequences of amino acids. The first peptide starts with Cys (cysteine), followed by Ser (serine), Ala (alanine), Ile (isoleucine), Gln (glutamine), Asn (asparagine), and ends with Lys (lysine). On the other hand, the second peptide starts with Gln, followed by Ser, Cys, Lys, Asn, Ile, and ends with Ala.
Therefore, option b is the correct answer: The two peptides differ in amino acid sequence.
Learn more about Peptides amino acids:
https://brainly.com/question/14351754
#SPJ11