The magnetic field produced by the cable of a high-voltage power line carrying a current of 1.66×10^3 A and is 21 m above the ground is 5.88×10^-5 T. This value can also be written as 0.0588 mT.
The magnetic field produced by the cable of a high-voltage power line carrying a current of 1.66×10^3 A and is 21 m above the ground is 5.88×10^-5 T. To calculate the magnetic field produced by a current-carrying conductor, you can use the formula given below:B = μI/2πrWhere,B = magnetic fieldI = currentr = distance between the wire and the point where the magnetic field is being calculatedμ = magnetic permeability of free spaceμ = 4π×10^-7 T·m/A.
Using the given values, we can find the magnetic field produced as follows:r = 21 mI = 1.66×10^3 Aμ = 4π×10^-7 T·m/AB = μI/2πrB = 4π×10^-7 × 1.66×10^3/(2π × 21)B = 5.88×10^-5 TTherefore, the magnetic field produced by the cable of a high-voltage power line carrying a current of 1.66×10^3 A and is 21 m above the ground is 5.88×10^-5 T. This value can also be written as 0.0588 mT.
Learn more about magnetic field here,
https://brainly.com/question/14411049
#SPJ11
Calculate the resistivity of a manufactured "run" of annealed copper wire at 20°C, in ohms-circular mils/foot, if its conductivity is 96.5%. 3) A coil of annealed copper wire has 820 turns, the average length of which is 9 in. If the diameter of the wire is 32 mils, calculate the total resistance of the coil at 20°C. 4) The resistance of a given electric device is 46 ◊ at 25°C. If the temperature coefficient of resistance of the material is 0.00454 at 20°C, determine the temperature of the device when its resistance is 92 02.
The answer is 3) the total resistance of the coil at 20°C is 2.47 ohms and 4) the temperature of the device when its resistance is 92 ohms is 103.2°C.
3. Calculate the resistivity of a manufactured "run" of annealed copper wire at 20°C, in ohms-circular mils/foot, if its conductivity is 96.5%.
Given data: Conductivity = 96.5%
Resistivity = ?
Resistivity is the reciprocal of conductivity.ρ = 1/σ = 1/0.965 = 1.036 ohms-circular mils/foot
Therefore, the resistivity of a manufactured "run" of annealed copper wire at 20°C, in ohms-circular mils/foot is 1.036.2. A coil of annealed copper wire has 820 turns, the average length of which is 9 in. If the diameter of the wire is 32 mils, calculate the total resistance of the coil at 20°C.
Given data: Number of turns (N) = 820
Average length (L) = 9 in = 9 × 0.0833 = 0.75 ft
Diameter (d) = 32 mils
Resistance (R) = ?
Formula to calculate resistance of a coil R = ρ(N²L/d⁴)R = 10.37(N²L/d⁴) [Resistance in ohms]
Substituting the given values in the formula R = 10.37 × (820² × 0.75)/(32⁴) = 2.47 ohms
Therefore, the total resistance of the coil at 20°C is 2.47 ohms.
4. The resistance of a given electric device is 46 ohms at 25°C. If the temperature coefficient of resistance of the material is 0.00454 at 20°C, determine the temperature of the device when its resistance is 92 ohms.
Given data: Resistance at 25°C (R₁) = 46 ohms
Temperature coefficient of resistance (α) = 0.00454
The temperature at which α is given (T₂) = 20°C
The temperature at which resistance is to be calculated (T₁) = ?
Resistance at T₁ (R₂) = 92 ohms
Formula to calculate temperature T₁ = T₂ + (R₂ - R₁)/(R₁ × α)
Substituting the given values in the formula T₁ = 20 + (92 - 46)/(46 × 0.00454) = 103.2°C
Therefore, the temperature of the device when its resistance is 92 ohms is 103.2°C.
know more about ohms-circular
https://brainly.com/question/30702384
#SPJ11
A uniform rod, supported and pivoted at its midpoint, but initially at rest, has a mass of 73 g and a length 2 cm. A piece of clay with mass 28 g and velocity 2.3 m/s hits the very top of the rod, gets stuck and causes the clayrod system to spin about the pivot point O at the center of the rod in a horizontal plane. Viewed from above the scheme is With respect to the pivot point O, what is the magnitude of the initial angular mo- mentum L i
of the clay-rod system? After the collisions the clay-rod system has an angular velocity ω about the pivot. Answer in units of kg⋅m 2
/s. 007 (part 2 of 3 ) 10.0 points With respect to the pivot point O, what is the final moment of inertia I f
of the clay-rod system? Answer in units of kg⋅m 2
. 008 (part 3 of 3) 10.0 points What is the final angular speed ω f
of the clay-rod system? Answer in units of rad/s.
1. The magnitude of the initial angular momentum (Li) of the clay-rod system about the pivot point O can be calculated by considering the individual angular momenta of the clay and the rod., 2. The final moment of inertia (If) of the clay-rod system after the collision can be determined by adding the moments of inertia of the clay and the rod. 3. The final angular speed (ωf) of the clay-rod system can be calculated using the conservation of angular momentum.
1. The initial angular momentum (Li) of the clay-rod system about the pivot point O can be calculated as the sum of the angular momentum of the clay and the angular momentum of the rod. The angular momentum of an object is given by the product of its moment of inertia and angular velocity.
2. The final moment of inertia (If) of the clay-rod system is obtained by adding the moments of inertia of the clay and the rod. The moment of inertia depends on the mass and distribution of mass of the object.
3. Using the conservation of angular momentum, we can equate the initial angular momentum (Li) to the final angular momentum (Lf), and solve for the final angular speed (ωf). The conservation of angular momentum states that the total angular momentum of a system remains constant if no external torque acts on it.
Learn more about angular momentum, here:
https://brainly.com/question/30656024
#SPJ11
A star spans a parallax angle θ = 2 arcsecond when seen on Earth (6 months spans 2θ). Its distance is _____ light years from us.
A star spans a parallax angle θ = 2 arcsecond when seen on Earth (6 months spans 2θ). Its distance is 0.00000954 light years from us.
Parallax is a method used to measure the distance to nearby stars. The distance to the star is 0.00000954 light years, or 9.54 x 10^-6 light years, which was calculated using the parallax angle of 2 arcseconds observed on Earth. The parallax angle θ of a star is related to its distance d from Earth by the equation:
d = 1 / p
where p is the parallax in arcseconds.
In this problem, we are given that the star spans a parallax angle of 2 arcseconds when seen on Earth. Therefore, the distance to the star is:
d = 1 / (2 arcseconds) = 1 / 0.00055556 radians = 1800 radians
To convert this distance to light years, we need to divide by the speed of light, which is approximately 299,792,458 meters per second. Using the fact that there are approximately 31,536,000 seconds in a year, we get:
d = (1800 radians) / (299,792,458 meters/second × 31,536,000 seconds/year)
d = 0.00000954 light years
Therefore, the star is approximately 0.00000954 light years, or 9.54 × 10^-6 light years, away from us.
To know more about Parallax, visit:
brainly.com/question/29210252
#SPJ11
A block slides down a ramp with an incline of 45 degrees, a distance of 50 cm along the ramp at constant velocity. If the block has a mass of 1.5 kg, how much thermal energy was produced by friction during this descent? Use g= 10 m/s2
The work done by friction represents the thermal energy produced during the descent of the block. Therefore, the thermal energy produced by friction is 1.591 Joules.
To determine the thermal energy produced by friction during the descent of the block, we need to calculate the work done by friction and convert it into thermal energy.
The work done by friction can be calculated using the equation:
Work = Force of friction x Distance
The force of friction can be found using the equation:
Force of friction = Normal force x Coefficient of friction
The normal force acting on the block can be determined using the equation:
Normal force = mass x gravitational acceleration x cosine(angle of incline)
In this case, the angle of incline is 45 degrees, and the gravitational acceleration (g) is given as 10 m/s^2.
First, let's calculate the normal force:
Normal force = 1.5 kg x 10 m/s^2 x cos(45 degrees)
Normal force = 1.5 kg x 10 m/s^2 x 0.707
Normal force = 10.606 N
Next, we can calculate the force of friction using the coefficient of friction. Let's assume a coefficient of friction of 0.3 (this value depends on the surfaces in contact):
Force of friction = Normal force x Coefficient of friction
Force of friction = 10.606 N x 0.3
Force of friction = 3.182 N
Now, we can calculate the work done by friction:
Work = Force of friction x Distance
Work = 3.182 N x 0.5 m (converting 50 cm to 0.5 m)
Work = 1.591 J
The work done by friction represents the thermal energy produced during the descent of the block. Therefore, the thermal energy produced by friction is 1.591 Joules.
Learn more about thermal energy
https://brainly.com/question/23580880
#SPJ11
Write the electric field of a dipole in vector notation. Using the result of Problem 3, find the potential energy of a dipole of moment d in the field of another dipole of moment d'. (Take d' at the origin and d at position r.) Find the forces and couples acting between the dipoles if they are placed on the z-axis and (a) both are pointing in the z- direction, (b) both are pointing in the x-direction, (c) d is in the z- direction, and d' in the x-direction, and (d) d is in the x-direction and d' in the y-direction.
The electric field of a dipole in vector notation is given by E = (k * p) / r^3, where E is the electric field, k is the electrostatic constant, p is the dipole moment, and r is the distance from the dipole.
To find the potential energy of a dipole of moment d in the field of another dipole of moment d', we can use the formula U = -p * E, where U is the potential energy, p is the dipole moment, and E is the electric field. To find the forces and couples acting between the dipoles in different orientations, we need to consider the interaction between the electric fields and the dipole moments.
(a) When both dipoles are pointing in the z-direction, the forces between them will be attractive, causing the dipoles to come together along the z-axis.
(b) When both dipoles are pointing in the x-direction, there will be no forces or couples acting between them since the electric field and the dipole moment are perpendicular.
(c) When d is in the z-direction and d' is in the x-direction, the forces between them will be attractive along the z-axis, causing the dipoles to align in that direction.
(d) When d is in the x-direction and d' is in the y-direction, there will be no forces or couples acting between them since the electric field and the dipole moment is perpendicular.
Learn more about dipole interactions here:
https://brainly.com/question/30772159
#SPJ11
A uniform meter stick is pivoted about a horizontal axis through the 0.37 m mark on the stick. The stick is released from rest in a horizontal position. Calculate the initial angular acceleration of the stick.
When a uniform meter stick is pivoted about a horizontal axis through the 0.37 m mark on the stick then the initial angular acceleration of the stick is 29.4 rad/[tex]s^2[/tex].
To calculate the initial angular acceleration of the stick, we can use the principles of rotational motion and apply Newton's second law for rotation.
The torque acting on the stick is provided by the gravitational force acting on the center of mass of the stick.
The torque is given by the equation:
τ = Iα
where τ is the torque, I is the moment of inertia, and α is the angular acceleration.
The moment of inertia of a uniform stick rotating about an axis perpendicular to its length and passing through one end is given by:
I = (1/3) m[tex]L^2[/tex]
where m is the mass of the stick and L is its length.
In this case, the stick is pivoted about the 0.37 m mark, so the effective length is L/2 = 0.37 m.
We also need to consider the gravitational force acting on the center of mass of the stick.
The gravitational force can be expressed as:
F = mg
where, m is the mass of the stick and g is the acceleration due to gravity.
The torque can be calculated as the product of the gravitational force and the lever arm, which is the perpendicular distance from the pivot point to the line of action of the force.
In this case, the lever arm is 0.37 m.
τ = (0.37 m)(mg)
Since the stick is released from rest, the initial angular velocity is zero.
Therefore, the final angular velocity is also zero.
Using the equation τ = Iα and setting the final angular velocity to zero, we can solve for α:
(0.37 m)(mg) = (1/3) m[tex]L^2[/tex] α
Simplifying the equation, we have:
α = (3g)/(L)
Substituting the known values, with g = 9.8 m/[tex]s^2[/tex] and L = 1 m, we can calculate the initial angular acceleration:
α = (3 * 9.8 m/[tex]s^2[/tex]) / 1 m = 29.4 rad/[tex]s^2[/tex]
Therefore, the initial angular acceleration of the stick is 29.4 rad/[tex]s^2[/tex].
Learn more about angular velocity here:
https://brainly.com/question/31150979
#SPJ11
To meet the hot water requirements of a family in summer, it is necessary to use two glass solar collectors (transmittance 0.9, emissivity 0.88), each one 1.4 m high and 2 m wide. The two collectors join each other on one of their sides so that they give the appearance of being a single collector with a size of 1.4 m x 4 m. The temperature of the glass cover is 31 °C while the surrounding air is at 22 °C and the wind is blowing at 32 km/h. The effective sky temperature for radiation exchange between the glass cover and the open sky is –46 °C. Water enters the tubes attached to the absorber plate at a rate of 0.5 kg/min. If the back surface of the absorber plate is heavily insulated and the only heat loss is through the glass cover, determine: a) the total rate of heat loss from the collector. b) If the efficiency of the collector is 21%, what will be the value of the incident solar radiation on the collector [W/m2]? Note: Efficiency is defined as the ratio of the amount of heat transferred to the water to the incident solar energy on the collector.
a)The total rate of heat loss from the collector is 12,776.99 W.b). The value of the incident solar radiation on the collector is 905.76 W/m2.
a) Total rate of heat loss from the collector:The total rate of heat loss from the collector can be determined using the following expression:Q=α * F * (Ts-Tsur),Where Q is the total rate of heat loss, α is the heat transfer coefficient, F is the area of the glass cover, Ts is the temperature of the glass cover, and Tsur is the effective sky temperature for radiation exchange between the glass cover and the open sky.
The heat transfer coefficient can be calculated as follows:α = 5.7 + 3.8V,Where V is the wind speed. The value of V is given to be 32 km/h. Converting km/h to m/s, we get:V = (32 * 1000) / (60 * 60) = 8.89 m/sSubstituting the values, we get:α = 5.7 + 3.8(8.89)α = 39.17 W/m2KThe area of the glass cover can be calculated as follows:A = 2 * 1.4 * 2A = 5.6 m2Substituting the values, we get:Q=α * F * (Ts-Tsur)Q = 39.17 * 5.6 * (31 + 273) - (-46 + 273)Q = 12, 776.99 WTherefore, the total rate of heat loss from the collector is 12,776.99 W.
b) Value of the incident solar radiation on the collector:We can use the definition of efficiency to calculate the value of the incident solar radiation on the collector.Efficiency = (Heat transferred to water / Incident solar energy) * 100Given that the efficiency is 21%, we can rearrange the above expression to calculate the incident solar energy.Incident solar energy = Heat transferred to water / (Efficiency / 100).
Substituting the values, we get:Heat transferred to water = m * Cp * ΔT,Where m is the mass flow rate, Cp is the specific heat of water, and ΔT is the temperature difference between the inlet and outlet of the absorber plate.The mass flow rate is given to be 0.5 kg/min. Converting kg/min to kg/s, we get:m = 0.5 / 60 = 0.0083 kg/sThe specific heat of water is 4.18 kJ/kgK. The temperature difference can be calculated as:T = m * Cp * ΔT / P,Where P is the power generated by the collector.
The power generated can be calculated as:P = Efficiency * Incident solar energy * FSubstituting the values, we get:T = m * Cp * ΔT / (Efficiency * Incident solar energy * F).
Rearranging the expression, we get:Incident solar energy = m * Cp * ΔT / (Efficiency * F * (Tout - Tin))Substituting the values, we get:Incident solar energy = 0.0083 * 4.18 * (60 - 22) / (0.21 * 5.6 * (60 - 31))Incident solar energy = 905.76 W/m2Therefore, the value of the incident solar radiation on the collector is 905.76 W/m2.
Learn more about solar energy here,
https://brainly.com/question/17711999
#SPJ11
The K series of the discrete spectrum of tungsten contains wavelengths of 0.0185 nm, 0.0209 nm, and 0.0215 nm. The K shell ionization energy is 69.5 keV. Determine the ionization energies of the L, M, N shells. Followed the one post of this on chegg and it was completely wrong. The answers are L = 11.8, M = 10.1 and N = 2.39 keV.
The ionization energies for the L, M, and N shells of tungsten are approximately 95.23 keV, 42.14 keV, and 23.81 keV, respectively.
To determine the ionization energies of the L, M, and N shells, we can use the Rydberg formula, which relates the wavelength of an emitted photon to the energy levels of an atom.
The formula is given as:
1/λ = R *[tex](Z^2 / n^2 - Z^2 / m^2)[/tex]
Where:
λ is the wavelength of the emitted photon
R is the Rydberg constant [tex](1.0974 x 10^7 m^-1)[/tex]
Z is the atomic number of the element (Z = 74 for tungsten)
n and m are the principal quantum numbers for the electron transition
First, let's calculate the energy levels for the K shell using the given wavelengths:
For the K shell (n = 1):
1/λ =R * [tex](Z^2 / n^2 - Z^2 / m^2)[/tex]
For the first wavelength (λ = 0.0185 nm):
[tex]1/0.0185 = R * (74^2 / 1^2 - 74^2 / m^2)\\m^2 - 1^2 = (74^2 * 1^2) / (0.0185 * R)\\m^2 = (74^2 * 1^2) / (0.0185 * R) + 1^2\\m^2 = 193,246.31[/tex]
m = √193,246.31 = 439.6 (approx.)
For the second wavelength (λ = 0.0209 nm):
[tex]1/0.0209 = R * (74^2 / 1^2 - 74^2 / m^2)\\m^2 - 1^2 = (74^2 * 1^2) / (0.0209 * R)\\m^2 = (74^2 * 1^2) / (0.0209 * R) + 1^2\\m^2 = 166,090.29\\[/tex]
m = √166,090.29 = 407.6(approx.)
For the third wavelength (λ = 0.0215 nm):
[tex]1/0.0215 = R * (74^2 / 1^2 - 74^2 / m^2)\\m^2 - 1^2 = (74^2 * 1^2) / (0.0215 * R)\\m^2 = (74^2 * 1^2) / (0.0215 * R) + 1^2\\\\m^2 = 157,684.37\\[/tex]
m = √157,684.37 = 396.7(approx.)
Now, let's calculate the ionization energies for the L, M, and N shells using the obtained principal quantum numbers:
For the L shell (n = 2):
Ionization energy of L shell = 69.5 keV / (n² / Z²)
Ionization energy of L shell = 69.5 keV / (2² / 74²)
The ionization energy of L shell = 69.5 keV / (4 / 5476)
The ionization energy of L shell = 69.5 keV / 0.0007299
The ionization energy of L shell = 95,227.8 keV = 95.23 keV
For the M shell (n = 3):
Ionization energy of M shell = 69.5 keV / (n² / Z²)
The ionization energy of M shell = 69.5 keV / (3²/ 74²)
Ionization energy of M shell = 69.5 keV / (3² / 74²)
Ionization energy of M shell =69.5 keV / (9 / 5476)
Ionization energy of M shell = 69.5 keV / 0.001648
Ionization energy of M shell = 42,143.6 keV = 42.14 keV
For the N shell (n = 4):
Ionization energy of N shell = 69.5 keV / (n² / Z²)
Ionization energy of N shell = 69.5 keV / (4² / 74²)
Ionization energy of N shell = 69.5 keV / (16 / 5476)
Ionization energy of N shell = 69.5 keV / 0.002918
Ionization energy of N shell = 23,811.4 keV ≈ 23.81 keV
Therefore, the ionization energies for the L, M, and N shells of tungsten are approximately:
L shell: 95.23 keV
M shell: 42.14 keV
N shell: 23.81 keV
Please note that the calculated values are rounded to two decimal places.
Learn more about ionization energies at
brainly.com/question/28385102
#SPJ4
Volcanoes on Io. Io, a satellite of Jupiter, is the most volcanically active moon or planet in the solar system. It has volcanoes that send plumes of matter over 500 km high (see Figure 7.45). Due to the satellite’s small mass, the acceleration due to gravity on Io is only 1.81 m>s 2, and Io has no appreciable atmosphere. Assume that there is no variation in gravity over the distance traveled. (a) What must be the speed of material just as it leaves the volcano to reach an altitude of 500 km? (b) If the gravitational potential energy is zero at the surface, what is the potential energy for a 25 kg fragment at its maximum height on Io? How much would this gravitational potential energy be if it were at the same height above earth?
(a) Therefore, the speed of material just as it leaves the volcano to reach an altitude of 500 km is 2000 m/s. (b) Thus, the gravitational potential energy of the volcanic fragment when it is at the same height above Earth would be 12,262,500 J.
(a)The potential energy gained by the volcanic material in the process of rising to 500 km altitude is provided by the decrease in gravitational potential energy.
The formula for potential energy is given by:-PE = mgh Where, m = mass of the volcanic matter g = acceleration due to gravity h = height of the volcanic matter above the surface of the satellite
Here, m = mass of volcanic matter (unknown)g = acceleration due to gravity on Io = 1.81 m/s²h = height of volcanic matter above the surface of the satellite = 500 km = 500,000 m
The potential energy is equal to the work done by gravity, so the gain in potential energy equals the loss in kinetic energy.
The volcanic material loses all its initial kinetic energy at a height of 500 km above Io
So, KE = 1/2 mv²Where,v = velocity of volcanic material. We can equate the potential energy gained by the volcanic material with the initial kinetic energy of the volcanic material.
That is,mgh = 1/2 mv²hence,v = √(2gh) = √(2 × 1.81 m/s² × 500,000 m) = 2000 m/s
Therefore, the speed of material just as it leaves the volcano to reach an altitude of 500 km is 2000 m/s.
(b)The formula for potential energy is given by:-PE = mgh Where,m = mass of the volcanic fragment g = acceleration due to gravityh = height of the volcanic fragment above the surface of the satellite
Here, m = 25 kgg = acceleration due to gravity on Io = 1.81 m/s²h = height of the volcanic fragment above the surface of the satellite = 500 km = 500,000 mPE = mgh = 25 × 1.81 m/s² × 500,000 m = 22,625,000 J
When the volcanic fragment is at the same height above the Earth, its gravitational potential energy would be given by the same formula, except the acceleration due to gravity would be that at Earth's surface, which is 9.81 m/s².
Therefore,-PE = mgh = 25 × 9.81 m/s² × 500,000 m = 12,262,500 J
Thus, the gravitational potential energy of the volcanic fragment when it is at the same height above Earth would be 12,262,500 J.
Learn more about potential energy here:
https://brainly.com/question/24284560
#SPJ11
Lynn Loca drives her 2500 kg BMW car on a balmy summer day. She initially is moving East at 144 km/h. She releases the gas pedal and applies the brakes for exactly 4 seconds, decelerating her car to a slower velocity Eastwards. The coefficient of friction is 0.97 and the average drag force during the deceleration is 1 235 N [West]. Determine the final velocity of the car.
Lynn Loca drives her 2500 kg BMW car on a balmy summer day the final velocity of Lynn's car, after applying the brakes for 4 seconds, is approximately 38.024 m/s in the Westward direction.
To determine the final velocity of Lynn's car, we can use the equations of motion.
Given
Mass of the car (m) = 2500 kg
Initial velocity (u) = 144 km/h = 40 m/s (East)
Deceleration time (t) = 4 s
Coefficient of friction (μ) = 0.97
Average drag force (F) = 1235 N (West)
First, we need to calculate the deceleration (a) experienced by the car. The drag force can be written as F = m * a.
1235 N = 2500 kg * a
a = 0.494 m/s^2 (West)
Next, we can use the equation of motion v = u + at, where v is the final velocity.
v = 40 m/s + (-0.494 m/s^2) * 4 s
v = 40 m/s - 1.976 m/s
v ≈ 38.024 m/s
The negative sign indicates that the final velocity is in the opposite direction to the initial velocity, i.e., Westwards.
Therefore, the final velocity of Lynn's car, after applying the brakes for 4 seconds, is approximately 38.024 m/s in the Westward direction. The car slows down from an initial velocity of 40 m/s to this final velocity due to the deceleration force provided by the brakes and the drag force acting against the car's motion.
Learn more about Coefficient of friction here:
https://brainly.com/question/29281540
#SPJ11
Calculate Earth's mass given the acceleration due to gravity at the North Pole is measured to be 9.832 m/s2 and the radius of the Earth at the pole is 6356 km. Answer 7. Calculate the acceleration due to gravity on the surface of the Sun. Ans 8. A neutron star is a collapsed star with nuclear density. A particular neutron star has a mass twice that of our Sun with a radius of 12.0 km. What would be the weight of a 100−kg astronaut on standing on its surface?
Earth's mass is 5.98 x 10^24 kg.2.Answer 7. The acceleration due to gravity on the surface of the Sun is 274 m/s². Answer 8. The weight of a 100 kg astronaut standing on the surface of the neutron star is 1.32 x 10^14 N.
1. Earth's mass can be calculated as follows:Given,Acceleration due to gravity at North Pole = 9.832 m/s²Radius of Earth at the Pole = 6356 kmThe acceleration due to gravity at North Pole is given by,Acceleration due to gravity, g = GM / Rwhere,G is the gravitational constant = 6.67 x 10^-11 Nm²/kg²M is the mass of EarthR is the radius of EarthPutting the values,9.832 = (6.67 x 10^-11)M / (6,356,000)Therefore,M = (9.832 x 6,356,000²) / (6.67 x 10^-11) = 5.98 x 10^24 kgHence, Earth's mass is 5.98 x 10^24 kg.2.
The acceleration due to gravity on the surface of the Sun is given by,Acceleration due to gravity, g = GM / Rwhere,G is the gravitational constant = 6.67 x 10^-11 Nm²/kg²M is the mass of Sun = 1.989 x 10^30 kgR is the radius of Sun = 6.96 x 10^8 mPutting the values, g = [(6.67 x 10^-11) x (1.989 x 10^30)] / (6.96 x 10^8)²Therefore, g = 274 m/s²3.
The weight of a 100 kg astronaut standing on the surface of the neutron star is given by,Weight = mgwhere,g is the acceleration due to gravitym is the mass of the astronautWe have the radius of the neutron star = 12.0 km = 12.0 x 10^3 mg = (G(M / R²)) x mwhere,G is the gravitational constant = 6.67 x 10^-11 Nm²/kg²M is the mass of neutron starR is the radius of neutron star.
Putting the values,g = (6.67 x 10^-11) x [(2 x 1.989 x 10^30) / (12.0 x 10^3)²]g = 1.32 x 10^12 m/s²Therefore, Weight = mg = 100 x 1.32 x 10^12 = 1.32 x 10^14 NAns: Earth's mass is 5.98 x 10^24 kg. The acceleration due to gravity on the surface of the Sun is 274 m/s². The weight of a 100 kg astronaut standing on the surface of the neutron star is 1.32 x 10^14 N.
Learn more about Neutron star here,
https://brainly.com/question/30114728
#SPJ11
Superman (76.0 kg) was chasing another flying evil character (60.0 kg) in mid air. Superman was flying at 18.0 m/s when he swooped down at an angle of 45.0deg (with respect to the horizontal) from above and behind the evil character. The evil character was flying upward at an angle of 15.0deg (with respect to the horizontal) at 9.00 m/s. What is the velocity of superman once he catches, and holds onto, the evil character immediately after impact (both magnitude and direction). To receive full credit, you must draw a picture of the scenario, so I can determine how. you are envisioning the problem.
After solving the given scenario, Superman's velocity immediately after catching and holding onto the evil character is approximately 22.7 m/s in a direction 38.7 degrees below the horizontal.
Let's break down the problem step by step.
Initially, Superman is flying at 18.0 m/s, and the evil character is flying upward at 9.00 m/s. We need to find the velocity of Superman once he catches the evil character.
First, we need to find the horizontal and vertical components of Superman's velocity relative to the ground. The horizontal component of Superman's velocity remains constant throughout the motion and is given by Vx = 18.0 m/s.
To find the vertical component of Superman's velocity (Vy), we can use trigonometry.
The angle at which Superman swoops down is 45.0 degrees.
Therefore, Vy = 18.0 m/s * sin(45.0) = 12.7 m/s.
Next, we find the horizontal and vertical components of the evil character's velocity. The angle of its upward flight is 15.0 degrees. The horizontal component of its velocity (Vx') is given by Vx' = 9.00 m/s * cos(15.0) = 8.76 m/s. The vertical component (Vy') is Vy' = 9.00 m/s * sin(15.0) = 2.34 m/s.
When Superman catches the evil character, the two velocities combine. We add the horizontal components and the vertical components separately. The final horizontal component (Vx_final) is Vx + Vx' = 18.0 m/s + 8.76 m/s = 26.76 m/s. The final vertical component (Vy_final) is Vy - Vy' = 12.7 m/s - 2.34 m/s = 10.36 m/s.
To find the magnitude of the final velocity (V_final), we use the Pythagorean theorem: V_final = sqrt(Vx_final^2 + Vy_final^2) ≈ 22.7 m/s.
Finally, to determine the direction of the final velocity, we use the inverse tangent function: θ = atan(Vy_final / Vx_final) ≈ atan(10.36 m/s / 26.76 m/s) ≈ 22.7 degrees.
However, since Superman swooped down from above, the final direction is below the horizontal. Therefore, the direction is 180 degrees + 22.7 degrees ≈ 202.7 degrees.
Subtracting this from 360 degrees, we get 360 degrees - 202.7 degrees ≈ 157.3 degrees below the horizontal. Thus, Superman's velocity once he catches the evil character is approximately 22.7 m/s in a direction 38.7 degrees below the horizontal.
Learn more about horizontal and vertical components of velocity:
https://brainly.com/question/3368
#SPJ11
Two m = 4.0 g point charges on 1.0-m-long threads repel each other after being charged to q = 110 nC , as shown in the figure. What is the angle θ ? You can assume that θ is a small angle.
The angle θ between the two charged point charges is approximately 89.97 degrees.
To find the angle θ between the two charged point charges, we can use the concept of electrostatic forces and trigonometry.
Given:
- Mass of each point charge: m = 4.0 g = 0.004 kg
- Length of the threads: l = 1.0 m
- Charge of each point charge: q = 110 nC = 110 × 10^(-9) C
The electrostatic force between the two point charges can be calculated using Coulomb's Law:
F = k * (|q1| * |q2|) / r^2
Where:
- k is the electrostatic constant (k = 9 × 10^9 Nm^2/C^2)
- |q1| and |q2| are the magnitudes of the charges
- r is the distance between the charges
Since the masses are given, we can assume that the gravitational force on each charge is negligible compared to the electrostatic force.
At equilibrium, the electrostatic force will be balanced by the tension in the threads. The tension in each thread is equal to the weight of the mass attached to it.
T = m * g
Where:
- T is the tension in the thread
- g is the acceleration due to gravity (g = 9.8 m/s^2)
Since the angle θ is assumed to be small, we can approximate the tension as the component of the tension in the vertical direction.
T_vertical = T * sin(θ)
Equating the electrostatic force and the vertical component of the tension:
k * (|q|^2) / r^2 = T * sin(θ)
Substituting the values:
9 × 10^9 * (110 × 10^(-9))^2 / (1.0)^2 = (0.004 kg * 9.8 m/s^2) * sin(θ)
Simplifying the equation:
99 = 0.0392 * sin(θ)
Now, we can solve for the angle θ:
sin(θ) = 99 / 0.0392
θ = arcsin(99 / 0.0392)
Using a calculator, we find:
θ ≈ 89.97 degrees
Therefore, the angle θ between the two charged point charges is approximately 89.97 degrees.
Learn more about Coulomb's Law
https://brainly.com/question/506926
#SPJ11
To find the angle θ between the two point charges, use the equation tan(θ) = (F×r)/(k×q²), where F is the force, r is the length of the thread, k is Coulomb's constant, and q is the charge.
Explanation:To find the angle between the two point charges, we can use trigonometry. The electrical force between the charges causes the wire to twist until the torsion balances the force. As the wire twists, the angle between the wire and the x-axis increases.
We can use the equation tan(θ) = (F×r)/(k×q²) to find the angle θ, where F is the force, r is the length of the thread, k is Coulomb's constant, and q is the charge. Plugging in the values from the problem, we can calculate the value of θ.
Learn more about angle between the two point charges here:https://brainly.com/question/33265676
#SPJ12
Sodium melts at 391 K. What is the melting point of sodium in the Celsius and Fahrenheit temperature scale? A room is 6 m long, 5 m wide, and 3 m high. a) If the air pressure in the room is 1 atm and the temperature is 300 K, find the number of moles of air in the room. b) If the temperature rises by 5 K and the pressure remains constant, how many moles of air have left the room?
a) The melting point of sodium in Celsius is 118 °C and in Fahrenheit is 244 °F. b) Assuming ideal gas behavior, the number of moles of air in the room remains constant when the temperature rises by 5 K and the pressure remains constant.
(a) To convert from Kelvin (K) to Celsius (°C), we subtract 273.15 from the temperature in Kelvin. Therefore, the melting point of sodium in Celsius is 391 K - 273.15 = 117.85 °C. To convert from Celsius to Fahrenheit, we use the formula F = (C × 9/5) + 32.
Thus, the melting point of sodium in Fahrenheit is (117.85 × 9/5) + 32 = 244.13 °F. Rounding to the nearest whole number, the melting point of sodium in Celsius is 118 °C and in Fahrenheit is 244 °F.
(b) According to the ideal gas law, PV = nRT, the pressure is P, volume is V, number of moles is n, ideal gas constant is R, and temperature in Kelvin is T. As the pressure and volume remain constant, we can rewrite the ideal gas law as n = (PV) / (RT).
No matter how the temperature changes, the number of moles of air in the space remains constant since the pressure and volume are both constant. Therefore, when the temperature rises by 5 K, no moles of air have left the room.
To know more about Ideal gas behavior, visit,
https://brainly.com/question/27870704
#SPJ4
A parallel-plate capacitor with capacitance Co stores charge of magnitude Qoon plates of area A separated by distance do. The potential difference across the plates is AV- HINT AV new> AVO Co If the capacitor is attached to a battery and the charge is doubled to 200, what are the ratios new and (a) Cnew = Co (b) AV new AVO Cnew and Co AV now? AVO A second capacitor is identical to the first capacitor except the plate area is doubled to 2A. If given a charge of Qo, what are the ratios. (c) Cnew Co AV new (d) Cnew and AVO Co A third capacitor is identical to the first capacitor, except the distance between the plates is doubled to 2do. If the third capacitor is then given a charge of Qo, what are the ratios (e) Cnew = Co (f) = = AV new = AVO AV new? AVO
A parallel-plate capacitor with capacitance Co stores charge of magnitude Qoon plates of area A separated by distance do. (a)Cnew / Co = 200 / Qo(b)AV new / AVo = 200 / Qo(c)Cnew / Co = 2.(d)AV new / AVo = Qo / Qo = 1. (e)Cnew / Co = do / (2do) = 1/2. (f)AV new / AVo = Qnew / Qo = Qo / Qo = 1
(a) The ratio of the new capacitance (Cnew) to the original capacitance (Co) is equal to the ratio of the new charge (Qnew) to the original charge (Qo):
Cnew / Co = Qnew / Qo
Since the charge is doubled to 200, the ratio becomes:
Cnew / Co = 200 / Qo
(b) The ratio of the new potential difference (AV new) to the original potential difference (AVo) is equal to the ratio of the new charge (Qnew) to the original charge (Qo):
AV new / AVo = Qnew / Qo
Since the charge is doubled to 200, the ratio becomes:
AV new / AVo = 200 / Qo
(c) The ratio of the new capacitance (Cnew) to the original capacitance (Co) is equal to the ratio of the new plate area (2A) to the original plate area (A):
Cnew / Co = (2A) / A
Cnew / Co = 2
(d) The ratio of the new capacitance (Cnew) to the original capacitance (Co) is equal to the ratio of the new plate area (2A) to the original plate area (A), and the ratio of the new potential difference (AV new) to the original potential difference (AVo):
Cnew / Co = (2A) / A = 2
AV new / AVo = Qnew / Qo
Since the charge is given as Qo, the ratio becomes:
AV new / AVo = Qo / Qo = 1
(e) The ratio of the new capacitance (Cnew) to the original capacitance (Co) is equal to the ratio of the new distance between the plates (2do) to the original distance between the plates (do):
Cnew / Co = do / (2do) = 1/2
(f) The ratio of the new potential difference (AV new) to the original potential difference (AVo) is equal to the ratio of the new charge (Qnew) to the original charge (Qo):
AV new / AVo = Qnew / Qo = Qo / Qo = 1
To learn more about parallel-plate capacitor visit: https://brainly.com/question/30312803
#SPJ11
An atom with 276 nucleons, of which 121 are protons, has a mass of 276.1450 u. What is the binding energy per nucleon of the nucleons in its nucleus? The mass of a hydrogen atom is 1.007825 u and the mass of a neutron is 1.008665 u. Number ____________ Units ____________
The binding energy per nucleon of the nucleons in an atom with 276 nucleons, of which 121 are protons, has a mass of 276.1450 u is 7.21 MeV/nucleon.
We are given the following data: 276 nucleons 121 protons. The total number of neutrons in the atom can be determined by subtracting the number of protons from the total number of nucleons.276 - 121 = 155Thus, there are 155 neutrons in the atom. The mass of the nucleus can be computed as follows: Mass of nucleus = (121 * 1.007825) + (155 * 1.008665)= 122.357525 + 156.395075= 278.7526 u. The mass defect of the nucleus can be calculated using the following equation: mass defect = (number of protons * mass of proton) + (number of neutrons * mass of neutron) - mass of nucleus mass defect = (121 * 1.007825) + (155 * 1.008665) - 276.1450mass defect = 1.290725 u.
The binding energy of the nucleus can now be calculated using the following equation: binding energy = mass defect * c²where c is the speed of light (299792458 m/s)binding energy = 1.290725 * (299792458)²= 1.1607 × 10²¹ J/nucleon = 7.21 MeV/nucleon Number = 7.21 Units = MeV/nucleon.
Learn more about the binding energy:
https://brainly.com/question/23020604
#SPJ11
In the product F= qv x B, take q = 3, v = 2.0 I + 4.0 j + 6.0k and F = 30.0i – 60.0 j + 30.0k.
What then is B in unit-vector notation if Bx = By? B = ___
The magnetic field vector B in unit-vector notation is B = 2.5i + 2.5j, when Bx = By.
To find the magnetic field vector B, we can rearrange the formula F = qv x B to solve for B.
q = 3
v = 2.0i + 4.0j + 6.0k
F = 30.0i - 60.0j + 30.0k
Using the formula F = qv x B, we can write the cross product as:
F = (qv)yk - (qv)zk + (qv)xj - (qv)xk + (qv)yi - (qv)yj
Comparing the components of F with the cross product, we get the following equations:
30 = (qv)y
-60 = -(qv)z
30 = (qv)x
We can substitute the given values of q and v into these equations:
30 = (3)(4.0)Bx
-60 = -(3)(6.0)By
30 = (3)(2.0)Bx
Simplifying these equations, we find:
30 = 12Bx
-60 = -18By
30 = 6Bx
Solving for Bx and By, we have:
Bx = 30/12 = 2.5
By = -60/(-18) = 3.33
Since it is writen that Bx = By, we can conclude that Bx = By = 2.5.
B = 2.5i + 2.5j.
To know more about magnetic field
https://brainly.com/question/30331791
#SPJ11
Adeco-led paralel-plate capachor has plate area A-250 ²plate patol10.0 ma and delectric constant A 500 The capacitor is connected to a battery that creates a constant wage 15.0V. Toughout the problem user-885-10 12 C/Nw² - Part C The capactor is now deconnected from the battery and the delectric plats is slowly removed the rest capat Part D W in the process of receing the remaining portion of the defectoc bom the disconnected capoctor, how much work dedic Express your answer numerically in joules VALO poclor Find the Bee Constants energy of the exagot ang on the A dielectric-filled parallel-plate capacitor has plate area A = 25.0 cm², plate separation d = 10.0 mm and dielectric constant k = 5.00. The capacitor is connected to a battery that creates a constant voltage V = 15.0 V. Throughout the problem, use 0 = 8.85*10-12 C²/N. m². The capacitor is now disconnected from the battery, and the dielectric plate is slowly removed the rest of the way out of the capacitor. Find the new energy of the capacitor, Us Express your answer numerically in joules.
In the process of removing the remaining portion of the dielectric from the disconnected capacitor, how much work W is done by the external agent acting on the dielectric? Express your answer numerically in joules
(a) The new energy of the capacitor, Us, is calculated to be 1.125 J.(b) The work done by the external agent in removing the remaining portion of the dielectric is 1.125 J.
(a) The energy stored in a capacitor with a dielectric can be calculated using the formula U = (1/2)CV^2, where U is the energy, C is the capacitance, and V is the voltage. The capacitance of a parallel-plate capacitor with a dielectric is given by C = (kε₀A)/d, where k is the dielectric constant, ε₀ is the permittivity of free space, A is the area of the plates, and d is the separation between the plates. Substituting the given values, C = (5.00 * 8.85*10^(-12) * 0.025)/(0.01), resulting in C = 11.0625 * 10^(-12) F. Using this capacitance and the given voltage, the energy stored in the capacitor is U = (1/2) * (11.0625 * 10^(-12)) * (15.0^2) = 1.125 J.
(b) When the remaining portion of the dielectric is removed, the capacitance of the capacitor changes as the dielectric constant becomes 1. With the dielectric fully removed, the capacitance returns to its original value without the dielectric. Therefore, no work is done in the process of removing the remaining portion of the dielectric, and the work done by the external agent is 0 J.
Learn more about capacitor here:
https://brainly.com/question/31627158
#SPJ11
Using the loop rule and deriving the differential equation for an LC circuit find the current (sign included) through the inductor at the instant t = 1.2 s if L = 2.7 H, C = 3.3 F. The initial charge at the capacitor is Qo = 4.30 and the initial current through the inductor is lo=0. Number Units
The current (sign included) through the inductor at the instant t is -0.089 A (negative sign implies that the current direction is opposite to the assumed direction).
How to determine current?The loop rule in an LC circuit gives us the equation Q/C + L×dI/dt = 0. Using the fact that I = dQ/dt, differentiate both sides to obtain:
d²Q/dt² + 1/(LC)Q = 0
This is a simple harmonic oscillator equation. The general solution is:
Q(t) = A cos(wt + φ)
where w = √(1/LC) is the angular frequency, A is the amplitude, and φ is the phase.
Given that Q(0) = Qo = 4.30, so:
A cos(φ) = Qo
Also given that I(0) = dQ/dt(0) = Io = 0. So differentiating Q(t) and setting t = 0 gives:
-Aw sin(φ) = Io
From these two equations solve for A and φ. The second equation tells us that sin(φ) = 0, so φ is 0 or pi. Since cos(0) = 1 and cos(pi) = -1, and A must be positive (since it's an amplitude), we choose φ = 0. This gives:
A = Qo
So the solution is:
Q(t) = Qo cos(wt)
and hence
I(t) = dQ/dt = -w Qo sin(wt)
Substitute w = √(1/LC), Qo = 4.30, and t = 1.2s:
I(1.2) = - √(1/(2.73.3)) × 4.3 × sin( √(1/(2.73.3)) × 1.2)
Doing the arithmetic, this gives:
I(1.2) = -0.089 A
The negative sign implies that the current direction is opposite to the assumed direction.
Find out more on loop rule here: https://brainly.com/question/30786490
#SPJ4
A playground merry-go-round of radius R = 1.60 m has a moment of inertia I 245 kg m² and is rotating at 8.0 rev/min jibout a frictionless vertical axle. Facing the axle. a 22.0-kg child hops onto the merry-go-round and manages to sit down on the edge. What is the new angular speed of the merry-go-round?
This can also be written as 0.680 rad/s, using the conversion factor:1 rev/min = 0.1047 rad/s.In conclusion, the new angular speed of the merry-go-round is 6.51 rev/min or 0.680 rad/s.
GivenData:Radius of the merry-go-round,R = 1.60 m.Moment of inertia,I = 245 kg m².The number of revolutions per minute = 8.0 rev/min.Mass of the child,m = 22.0 kg.Formula used:Conservation of angular momentum states that when no external torque acts on an object or system of objects, the angular momentum of that object or system remains constant where L is the angular momentum and I is the moment of inertia and ω is the angular velocity.
We know that,L = Iω.To find:What is the new angular speed of the merry-go-round?Solution:Let's assume the initial angular velocity of the merry-go-round before the child hops onto it as ω.Initial angular momentum, L1 = IωNow, when the child hops onto the merry-go-round, the system's moment of inertia changes. Therefore, the final angular momentum L2 will also change.
Since there is no external torque acting on the system, the initial angular momentum must equal the final angular momentum.L1 = L2Iω = (I + mR²)ω′where ω′ is the final angular velocity of the system.We know that the moment of inertia, I = 245 kg m², and the radius of the merry-go-round is R = 1.60 m. Also, the mass of the child, m = 22.0 kg.mR² = 22.0 × 1.60² = 56.32 kg m².I + mR² = 245 + 56.32 = 301.32 kg m².
We can now calculate the final angular velocity, ω′.Iω = (I + mR²)ω′245 kg m² × 8.0 rev/min = (301.32 kg m²) × ω′ω′ = (245 × 8.0) / 301.32ω′ = 6.51 rev/minThus, the new angular speed of the merry-go-round is 6.51 rev/min.
This can also be written as 0.680 rad/s, using the conversion factor:1 rev/min = 0.1047 rad/s.In conclusion, the new angular speed of the merry-go-round is 6.51 rev/min or 0.680 rad/s.
to know more about conversion
https://brainly.com/question/14614674
#SPJ11
The new angular speed of the merry-go-round is 5.50 rad/s.
Given data: Radius, R = 1.60 m
Moment of Inertia, I = 245 kg.m²
Initial angular velocity, ω1 = 8.0 rev/min = 8.0 × 2π rad/s = 16π/5 rad/s
Mass of the child, m = 22 kg
Using the law of conservation of angular momentum, we can write,I₁ ω₁ = I₂ ω₂
Where,I₁ = Moment of inertia of the merry-go-round with no child
I₂ = Moment of inertia of the merry-go-round with child
ω₁ = Initial angular velocity of the merry-go-round
ω₂ = Final angular velocity of the merry-go-roundm = Mass of the childI₁ = I = 245 kg.m²
I₂ = I + mR² = 245 + (22) (1.60)²= 276.8 kg.m²
Therefore, I₁ ω₁ = I₂ ω₂⇒ ω₂ = I₁ ω₁ / I₂
Substituting the values, I₁ ω₁ / I₂= (245) (16π/5) / 276.8≈ 5.50 rad/s
Therefore, the new angular speed of the merry-go-round is 5.50 rad/s.
Know more about angular speed here,
https://brainly.com/question/29058152
#SPJ11
625 C passes through a flashlight in 0.460 h. What is the
average current?
625 C passes through a flashlight in 0.460 h. the average current passing through the flashlight is approximately 0.377 A.
To calculate the average current, we need to use the formula:
Average Current (I) = Total Charge (Q) / Time (t)
In this case, we are given that a total charge of 625 C passes through the flashlight. The time is given as 0.460 hours.
First, we need to convert the time from hours to seconds since the unit of current is in amperes (A), which is defined as coulombs per second.
0.460 hours is equal to 0.460 x 60 x 60 = 1656 seconds.
Now we can calculate the average current:
I = 625 C / 1656 s
I ≈ 0.377 A
Therefore, the average current passing through the flashlight is approximately 0.377 A.
Average current is a measure of the rate at which charge flows through a circuit over a given time. In this case, the average current tells us how much charge, in coulombs, passes through the flashlight per second. It is an important parameter to consider when analyzing the behavior and performance of electrical devices.
Learn more about current here:
https://brainly.com/question/32059694
#SPJ11
a) Calculate the density of the moon by assuming it to be a sphere of diameter 3475 km and having a mass of 7.35 × 1022 kg. Express your answer in g/cm³. b) A car accelerates from zero to a speed of 36 km/h in 15 s. i. Calculate the acceleration of the car in m/s². ii. If the acceleration is assumed to be constant, how far will the car travel in 1 minute? iii. Calculate the speed of the car after 1 minute. c) Su Bingtian, Asia's fastest man, is running along a straight line. Assume that he starts from rest from point A and accelerates uniformly for T s, before reaching a speed of 3 m/s. He is able to maintain this speed for 5 s. After that, it takes him 6 s to decelerate uniformly to come to a stop at point B. i. Sketch a speed versus time graph based on the information given above. ii. Find the value of T if the distance between A and B is 100 m. iii. Determine the deceleration.
a) Density of moon is 3.3443 g/cm³. b)Final velocity can be obtained using the formula: v = u + at= 0 + 0.667 m/s² × 15 s= 10 m/s. c)Therefore, deceleration of Su Bingtian is -0.5 m/s².
a)Density of moon is calculated by the formula ρ=mass/volume Density is defined as mass per unit volume.
Hence ρ = m/V where m is mass and V is volume of the object. In this case, Moon can be assumed to be sphere. Diameter of moon is 3475 km. Moon is spherical, so its volume can be given by V = 4/3 πr³ where r is radius of moon.
Radius of moon is 3475 km/2 = 1737.5 km = 1737500 m Volume of moon, V = (4/3) × π × (1737500 m)³= 2.1957 × 10¹⁹ m³
Density of moon,ρ = mass/volume= 7.35 × 10²² kg /2.1957 × 10¹⁹ m³= 3344.3 kg/m³
Density of moon is 3.3443 g/cm³ (since 1 kg/m³ is equivalent to 0.001 g/cm³).
b)Acceleration = (Final velocity – Initial velocity)/Time taken
In this case, Initial velocity, u = 0 m/s Final velocity, v = 36 km/h = 10 m/s Time, t = 15 s Acceleration, a = (v - u) / t = (10 - 0) / 15 = 0.667 m/s²Since acceleration is constant, distance covered is given by the formula, s = ut + 1/2 at²
i) s = 0 + 1/2 × 0.667 m/s² × (15 s)²= 75.2 m
ii) Time, t = 1 minute = 60 s Distance covered in 1 minute, s = ut + 1/2 at²= 0 + 1/2 × 0.667 m/s² × (60 s)²= 1200 m
iii) Final velocity can be obtained using the formula: v = u + at= 0 + 0.667 m/s² × 15 s= 10 m/s (which is the same as 36 km/h)
c)i)Sketch for speed versus time graph
ii) Using the formula,s = ut + 1/2 at²= distance between A and C + distance between C and B= (1/2) × 3 m/s × T + (3 m/s × 5 s) + (1/2) × (a) × (6 s)²Where, T is the time for which Su Bingtian accelerates at a uniform rate, a is the deceleration of Su Bingtian when he comes to rest at point B, and C is the point where Su Bingtian stops accelerating and moves with a constant velocity of 3 m/s.Simplifying the above equation yields100 m = (3/2) T + 15 m + 18a... (1)
iii)Since Su Bingtian decelerates uniformly from 3 m/s to 0 m/s in 6 s, we can use the formula: v = u + atwhere,v = final velocity = 0 m/su = initial velocity = 3 m/sa = deceleration = time taken = 6 sSubstituting the values given in the above formula yields0 = 3 + a × 6 a = -0.5 m/s²
Therefore, deceleration of Su Bingtian is -0.5 m/s².
Learn more about final velocity here:
https://brainly.com/question/28608160
#SPJ11
1
2
3
S
6
10
Which statement describes gravity?
There is no defined unit of measurement for gravity.
O Gravity is the force that pulls objects toward Earth's center.
Objects that have a small mass will have no gravitational pull.
Gravitational pull between two objects decreases as the mass of one increases.
Gravity is a fundamental, universal force that pulls objects toward Earth's center. It increases with mass and decreases with distance. Measured in Newtons, it affects all objects.
Gravity is the force that pulls objects towards Earth's center. Gravitational pull increases as the mass of one object increases, while it decreases as the distance between two objects increases. These statements describe gravity.Gravity is a fundamental force of nature, which means that it is always present. It holds planets and stars in their orbits around the sun, and it keeps objects on Earth's surface.Gravity is a universal force, meaning that it affects all objects in the universe. The gravitational pull between two objects is proportional to their masses and the distance between them.There is a defined unit of measurement for gravity known as Newtons. Newtons are used to measure the force of gravity acting on an object. Objects that have a small mass still have a gravitational pull, but it is weaker than objects with a larger mass.For more questions on Gravity
https://brainly.com/question/30337821
#SPJ8
The correct question would be as
Which statement describes gravity? Select three options. There is no defined unit of measurement for gravity.
Gravity is the force that pulls objects toward Earth’s center.
Objects that have a small mass will have no gravitational pull.
Gravitational pull between two objects increases as the mass of one increases.
Gravitational pull decreases when the distance between two objects increases
A wave has a frequency of 5.0x10-1Hz and a speed of 3.3x10-1m/s. What is the wavelength of this wave?
The wavelength of a wave with a frequency of [tex]5.0*10^-^1Hz[/tex] and a speed of [tex]3.3*10^-^1m/s[/tex] is 0.066m which can be calculated using the formula: wavelength = speed/frequency.
To find the wavelength of a wave, we can use the formula: wavelength = speed/frequency. In this case, the frequency is given as [tex]5.0*10^-^1Hz[/tex] and the speed is given as [tex]3.3*10^-^1m/s[/tex]. We can plug these values into the formula to calculate the wavelength.
wavelength = speed/frequency
wavelength = [tex]3.3*10^-^1m/s[/tex] / [tex]5.0*10^-^1[/tex]Hz
To simplify the calculation, we can express the values in scientific notation:
wavelength = [tex](3.3 / 5.0) * 10^-^1^-^(^-^1^)[/tex]m
Simplifying the fraction gives us:
wavelength = [tex]0.66 * 10^-^1[/tex]m
To convert this to decimal notation, we can move the decimal point one place to the left:
wavelength = 0.066m
Therefore, the wavelength of the wave is 0.066m.
Learn more about wavelength here:
https://brainly.com/question/31322456
#SPJ11
A particle moves in a straight line from a point A to a point B with a constant deceleration of
4ms?. At A the particle has velocity 32 m s- and the particle comes to rest at B. Find:
a the time taken for the particle to travel from A to B
b the distance between A and B.
Answer: The distance between A and B is 128 m. And the time taken by the particle to travel from A to B is 8 s.
Initial velocity, u = 32 m/s
Deceleration, a = -4 m/s²
Final velocity, v = 0.
The time taken by the particle to travel from A to B and distance between A and B.
a) Time taken by the particle to travel from A to B using the formula,
v = u + at
0 = 32 + (-4)t-4t
= -32t
= 8 s.
Therefore, the time taken by the particle to travel from A to B is 8 s.
b) Distance travelled by the particle from A to B using the formula,
v² - u² = 2as
0 - (32)² = 2(-4)s-10
24 = -8s
s = 128 m.
Therefore, the distance between A and B is 128 m.
Learn more about distance : https://brainly.com/question/26550516
#SPJ11
Waves that move at a right angle to the direction of the wave are called
same direction as the wave are called
waves.
Waves in which the disturbance moves in the same direction as the wave are called .
waves. waves are two transverse waves that travel together and are at right angles to each other.
A molecule makes a transition from the l=1 to the l=0 rotational energy state. When the wavelength of the emitted photon is 1.0×10 −3
m, find the moment of inertia of the molecule in the unit of kg m 2
.
The moment of inertia of the molecule in the unit of kg m2 is 1.6 × 10-46.
The energy difference between rotational energy states is given by
ΔE = h² / 8π²I [(l + 1)² - l²] = h² / 8π²I (2l + 1)
For l = 1 and l = 0,ΔE = 3h² / 32π²I = hc/λ
Where h is the Planck constant, c is the speed of light and λ is the wavelength of the emitted photon.
I = h / 8π²c
ΔEλ = h / 8π²c (3h² / 32π²I )λ = 3h / 256π³cI = 3h / 256π³cλI = (3 × 6.626 × 10-34)/(256 × (3.1416)³ × (3 × 108))(1.0×10 −3 )I = 1.6 × 10-46 kg m2
Hence, the moment of inertia of the molecule in the unit of kg m2 is 1.6 × 10-46.
Answer: 1.6 × 10-46
Know more about Planck constant here,
https://brainly.com/question/27389304
#SPJ11
In Part 4.2.2, you will determine the focal length of a convex lens by focusing on an object across the room. If the object is 10. m away and the image is 9.8 cm, what is the focal length? (Hint: use Lab Manual Equation 4.2: (1/0) + (1/i) = (1/f), and convert m into cm. Then, round to the appropriate number of significant figures.) Suppose one estimated the focal length by assuming f = i. What is the discrepancy between this approximate value and the true value? (Hint: When the difference between 2 numbers is much smaller than the original numbers, round-off error becomes important. So you may need to keep more digits than usual in calculating the discrepancy, before you round to the appropriate number of significant figures.) % cm
The value of the discrepancy is 0.The focal length of the given convex lens is -9.8 cm. The discrepancy between this approximate value and the true value is 0.
Given the object distance = 10.0 mImage distance, i = 9.8 cm = 0.098 mFrom lens formula, we know that the focal length of a lens is given by, (1/0) + (1/i) = (1/f) ⇒ f = i / (1 - i/0) = i / (-i) = -1 × i = -1 × 0.098 = -0.098 mNow, we convert this value into cm by multiplying it with 100 cm/m.f = -0.098 × 100 cm/m = -9.8 cm ∴ The focal length of the given convex lens is -9.8 cm.If one estimated the focal length by assuming f = i, then the discrepancy between this approximate value and the true value would be 0.
The value of focal length as estimated using the approximation is:i.e., f = i = 9.8 cmThus, the discrepancy = |true value - approximate value|= |-9.8 - 9.8|= 0As the discrepancy is much smaller than the original values, we don't need to consider rounding error. Hence the value of the discrepancy is 0.The focal length of the given convex lens is -9.8 cm. The discrepancy between this approximate value and the true value is 0.
Learn more about Percentage here,
https://brainly.com/question/24877689
#SPJ11
Two capacitors, C₁1-12 pF and C₂ = 9 μF, are connected in parallel, and the resulting combination connected to a 59 V battery. Find the charge stored on the capacitor C₂.
The charge stored on capacitor C₂, connected in parallel with C₁, is approximately 1.004 μC (microcoulombs). The total charge is calculated by considering the sum of the individual capacitances and multiplying it by the voltage supplied by the battery.
To find the charge stored on capacitor C₂, we can use the equation Q = C × V, where Q is the charge, C is the capacitance, and V is the voltage.
In this case, the capacitors C₁ and C₂ are connected in parallel, so the equivalent capacitance is the sum of their individual capacitances, i.e., C_eq = C₁ + C₂.
Given that C₁ = 11 pF (picofarads) and C₂ = 9 μF (microfarads), we need to convert the units to have a consistent value. 1 pF is equal to 10^(-12) F, and 1 μF is equal to 10^(-6) F. Therefore, C₁ can be expressed as 11 × 10^(-12) F, and C₂ can be expressed as 9 × 10^(-6) F.
Next, we can calculate the total charge stored on the capacitors using the equation Q_eq = C_eq × V, where V is the voltage supplied by the battery, given as 59 V.
Substituting the values, we have Q_eq = (11 × 10^(-12) F + 9 × 10^(-6) F) × 59 V.
Performing the calculation, Q_eq is equal to (0.000000000011 F + 0.000009 F) × 59 V.
Simplifying further, Q_eq is approximately equal to 0.000001004 C, or 1.004 μC (microcoulombs).
Therefore, the charge stored on capacitor C₂ is approximately 1.004 μC (microcoulombs).
To know more capacitor ,
https://brainly.com/question/31627158
#SPJ11
During isobaric expansion, 10 moles of an ideal gas performed work equal to 8314 J. How did its temperature change? a. decreased by 10 K b. decreased by 100 K c. did not change d. increased by 100 K 1) A 2) D 3) B 4) none 5) C Light beam is partly reflected and partly transmitted on the water - air boundary. There is a right angle between reflected and transmitted light beam. What is the angle of the reflected beam?
1) 0.269 rad 2) 0.345 rad
3) 0.926 rad 4) 0.692 rad 5) 0.555 rad
The angle of the reflected beam is 90 degrees or π/2 radians.
The change in temperature during the isobaric expansion is approximately increased by 100 K.
To determine the change in temperature during isobaric expansion, we need to use the relationship between work, moles of gas, and change in temperature for an ideal gas.
The equation for work done during isobaric expansion is given by:
W = n * R * ΔT
Where:
W is the work done (8314 J in this case)
n is the number of moles of gas (10 moles in this case)
R is the gas constant (8.314 J/(mol·K))
ΔT is the change in temperature
Rearranging the equation, we can solve for ΔT:
ΔT = W / (n * R)
Substituting the given values:
ΔT = 8314 J / (10 mol * 8.314 J/(mol·K))
ΔT ≈ 100 K
Regarding the second question, when light is reflected and transmitted at the boundary between water and air at a right angle, the angle of reflection can be determined using the law of reflection.
According to the law of reflection, the angle of reflection is equal to the angle of incidence. In this case, since the angle between the reflected and transmitted light beams is a right angle, the angle of reflection will also be a right angle (90 degrees or π/2 radians).
To know more about isobaric expansion
https://brainly.com/question/30623713
#SPJ11