A square plate is produced by welding together four smaller square plates,
each of side
a. The weight of each of the four plates is
shown in the figure.
Find the x-coordinate of the center of gravity (as a multiple of a).
Answer in units of a.
(PICTURED)
PART TWO
Find the y-coordinate of the center of gravity
(as a multiple of a).
Answer in units of a
Answer:
eExplanation:
3. A stone is thrown vertically upwards from the top of a building 50 m tall with an initial
velocity of 20.0 ms. If the stone just misses the edge of the roof on its return, determine
(a) The time is taken the stone to get to its maximum height.
(b) The maximum height reached by the stone
(c) The time at which the stone return to the point where it was thrown
(d) The velocity of the stone at this instance
(e) The velocity and position of the stone at t = 5 s.
Answer:
13.4436
Explanation:
A skier pushes off the top of a hill with an initial speed of 3.30 m/s. How fast will she be moving after dropping 5.00 meters in elevation if friction is negligible?
Answer:
eeeeeeeeeeeeeeeeeeeee
If the mass of the book is 50 sliding with acceleration 1.2 m/s ^ 2 then the friction force is
364N
185N
173N
73N
ANSWER AND I WILL GIVE YOU BRAINILIEST
Answer:
73N
Explanation:Just multiply 1.2^2 by 50
The most common stars in the universe are red dwarf stars. Red dwarf stars use their hydrogen fuel very slowly. Our universe also contains stars classified as blue supergiants. The table below lists the color and approximate surface temperatures of four stars. Based on the information from the table above, which of the following stars has the greatest absolute brightness?
The Sun
Vega
Bellatrix
Betelgeuse
Answer:
sun
Explanation:
An object with an initial horizontal velocity of 20 ft/s experiences a constant horizontal acceleration due to the action of a resultant force applied for 10 s. The work of the resultant force is 10 Btu. The mass of the object is 55 lb. Determine the constant horizontal acceleration, in ft/s2.
Answer:
a = 7.749 ft/s²
Explanation:
First to all, we need to convert all units, so we can work better in the calculations.
The horizontal acceleration is asked in ft/s² so the units of speed will be the same. The Work is in BTU and we need to convert it in ft.lbf in order to get the acceleration and final speed in ft/s:
W = 10 BTU * 778.15 Lbf.ft / BTU = 7781.5 lbf.ft
Now, to get the acceleration we need to get the final speed of the object first. This can be done, by using the following expression:
W = ΔKe (1)
And Ke = 1/2mV²
So Work would be:
W = 1/2 mV₂² - 1/2mV₁²
W = 1/2m(V₂² - V₁²) (2)
Finally, we need to convert the mass in lbf too, because Work is in lbf, so:
m = 55 lb * 1 lbf.s²/ft / 32.174 lb = 1.7095 lbf.s²/ft
Now, we can calculate the final speed by solving V₂ from (2):
7781.5 = (1/2) * (1.7095) * (V₂² - 20²)
7781.5 = 0.85475 * (V₂² - 441)
7781.5/0.85475 = (V₂² - 400)
9103.83 + 400 = V₂²
V₂ = √9503.83
V₂ = 97.49 ft/s
Now that we have the speed we can calculate the acceleration:
a = V₂ - V₁ / t
Replacing we have:
a = 97.49 - 20 / 10
a = 7.749 ft/s²Hope this helps
Two astronauts, each having a mass of 74.3 kg are connected by a 13.1 m rope of negligible mass. They are isolated in space, orbiting their center of mass at speeds of 5.65 m/s. a. Calculate the magnitude of the initial angular momentum of the system by treating the astronauts as particles.
Answer:
L = 5076.5 kg m² / s
Explanation:
The angular momentum of a particle is given by
L = r xp
L = r m v sin θ
the bold are vectors, where the angle is between the position vector and the velocity, in this case it is 90º therefore the sine is 1
as we have two bodies
L = 2 r m v
let's find the distance from the center of mass, let's place a reference frame on one of the masses
[tex]x_{cm}[/tex] = [tex]\frac{1}{M} \sum x_{i} m_{i}[/tex]i
x_{cm} = [tex]\frac{1}{m+m} ( 0 + l m)[/tex]
x_{cm} = [tex]\frac{1}{2m} lm[/tex]
x_{cm} = [tex]\frac{1}{2}[/tex]
x_{cm} = 13.1 / 2 = 6.05 m
let's calculate
L = 2 6.05 74.3 5.65
L = 5076.5 kg m² / s
Answer:
5076.5
Explanation:
You've been hired to design the hardware for an ink jet printer. You know that these printers use a deflecting electrode to cause charged ink drops to form letters on a page. The basic mechanism is that uniform ink drops of about 30 microns radius are charged to varying amounts after being sprayed out towards the page at a speed of about 20 m/s. Along the way to the page, they pass into a region between two deflecting plates that are 1.6 cm long. The deflecting plates are 1.0 mm apart and charged to 1500 volts. You measure the distance from the edge of the plates to the paper and find that it is one-half inch. Assuming an uncharged droplet forms the bottom of the letter, how much charge is needed on the droplet to form the top of a letter 3 mm high (11 pt. type)
Answer:
the required charged is 7.06 × 10⁻¹³ C
Explanation:
Given that;
Radius = 30 microns = 30 × 10⁻⁶
Speed v = 20 m/s
length x = 1.6 cm = 0.016 m
spacing d = 1.0 mm = 0.001 m
Voltage V = 1500 V
from the question, the electric field between the plates is uniform and equal to Voltage divided by the distance between the plates.
Electric field E = V/d
E = 1500 V / 0.001 m
E = 1.5 × 10⁶ V/m
Mass of ink drop m = pv
m = 10³ kg/m³ × [tex]\frac{4}{3}[/tex]πr³
m = 1000 kg/m³ × [tex]\frac{4}{3}[/tex]π × (30 × 10⁻⁶)³
m = 1.131 × 10⁻¹⁰ Kg
Time taken to travel t = x / sped
t = 0.016 m / 20 m/s
t = 0.0008 s
From the kinematic equation
to form the top of a letter 3 mm ( 0.003 m )high
y = [tex]\frac{1}{2}[/tex]at²
2y = at²
a = 2y/t²
we substitute
a = (2 × 0.003 m) / (0.0008 s)²
a = 9375 m/s²
Now Force F = Eq = ma
so
q = ma / E
we substitute
q = ( 1.131 × 10⁻¹⁰ Kg × 9375 m/s² ) / ( 1.5 × 10⁶ V/m )
q = 7.06 × 10⁻¹³ C
Therefore, the required charged is 7.06 × 10⁻¹³ C
The Short Answer:
Earth's tilted axis causes the seasons. Throughout the year, different
parts of Earth receive the Sun's most direct rays. So, when the North
Pole tilts toward the Sun, it's summer in the Northern Hemisphere. And
when the South Pole tilts toward the Sun, it's qvinter in the Northern
Hemisphere.
1. What direction is the Earth tilted in the summer here in
Buffalo?
a) towards the Sun
b) away from the Sun
23.5
Answer:
I cannot fully see the picture, but I'm going to have to tell you to go with towards the sun because it says summer.
Ropes 3 m and 5 m in length are fastened to a holiday decoration that is suspended over a town square. The decoration has a mass of 3 kg. The ropes, fastened at different heights, make angles of 52° and 40° with the horizontal. Find the tension in each wire and the magnitude of each tension. (Use g = 9.8 m/s2 for the acceleration due to gravity. Round your answers to two decimal places.)
Answer:
Explanation:
Let the tension in ropes be T₁ and T₂ . Ropes are making angle of 52 and 40 degree with the horizontal . The vertical component of tension will add up together to balance the weight of the decoration
T₁ sin52 + T₂ sin40 = 3 x 9.8
.788 T₁ + .643 T₂ = 29.4
The horizontal component of tension will add up to zero because the decoration piece is at rest .
T₁ cos52 + T₂ cos40 = 0
.615 T₁ - .766 T₂ = 0
T₁ = 1.24 T₂
Substituting this value of T₁ in earlier equation , we have
.788 x 1.24 T₂ + .643 T₂ = 29.4
1.62 T₂ = 29.4
T₂ = 18.15 N
T₁ = 1.24 x 18.15 = 22.51 N .
An athlete swims the length L of a pool in a time t1 and makes the return trip to the starting position in a time t2. If she is swimming initially in the positive x-direction, determine her average velocities symbolically in:
a. the first half of the swim
b. the second half of the swim
c. the round trip.
Answer:
B but I am not sure
Explanation:
if the forces on an object are balanced the resultant force is equal to zero true false
Answer:
If the forces are balanced, the resultant force is zero. If the forces on an object are unbalanced, this is what happens: a stationary object starts to move in the direction of the resultant force. a moving object changes speed and/or direction in the direction of the resultant force.
Explanation:
what is calculator program
Answer:
software calculator is a calculator that has been implemented as a computer program, rather than as a physical hardware device. They are among the simpler interactive software tools, and, as such, they: Provide operations for the user to select one at a time.
Answer: The calculator is a compact portable device that performs mathematical calculations. Some calculators also allow easy text editing and programming. It's also a programming software that simulates a portable calculator. Calculator applications help you make basic math calculations without leaving your screen.
Which mode of kinetic energy contributes to temperature?
Answer:
Kinetic energy Temperature
Explanation:
A system with a mass of 10 kg, initially moving horizontally with a velocity of 20 m/s, experiences a constant horizontal force of 25 N opposing the direction of motion. As a result, the system comes to rest. Determine the amount of energy transfer by work, in kJ, for this process and the total distance, in m, that the system travels
Answer:
Explanation:
Kinetic energy of the mass of 10 kg
= 1/2 m v² , m is mass and v is velocity .
= .5 x 10 x 20²
= 2000 J
The opposing force stops it . so work done by opposing force will be equal to this energy and it will be negative .
So energy transfer will be - 2000 J .
= 2 kJ .
If distance travelled by mass is d , force 25 N will have a displacement of d . so work done by force of 25 N
= 25 x d
25 d = 2000
d = 80 m .
Hence system travels a distance of 80 m .
A ball of mass m is thrown straight upward from ground level at speed v0. At the same instant, at a distance D above the ground, another ball of mass m is thrown straight downward toward the first ball, also at speed v0. Assume that gravity acts vertically downward on each mass m with a magnitude mg. v0 D b How far above the ground do the balls collide (in terms of only D, v0, and g)?
Answer:
Explanation:
Let the balls collide after time t .
distance covered by falling ball
s₁ = v₀ t + 1/2 g t²
distance covered by rising ball
s₂ = v₀ t - 1/2 g t²
Given ,
s₁ + s₂ = D
D = v₀ t + 1/2 g t² + v₀ t - 1/2 g t²
= 2v₀ t
t = D / 2v₀
s₂ = v₀ t - 1/2 g t²
= v₀ x D / 2v₀ - (1/2) x g x D² / 4v₀²
= D / 2 - gD² / 8 v₀²
First to answer gets brainliest
Answer:
has a charge
Explanation:
Answer:
gain electrons
Explanation:
I looked it up and that was what I found
side note: ions do have a charge
Suppose there is a 3Mbps uplink and 10Mbps downlink between a geostationary satellite and the base station on earth. If the propagation speed is the speed of light (3 * 10^8 m/sec), the packet size is 20Mb, and the distance from the satellite to earth is 36,000 km, what is the uplink propagation delay of the link in milliseconds
Answer:
[tex]120\ \text{ms}[/tex]
Explanation:
Distance between the satellite and Earth = [tex]36000\ \text{km}[/tex]
Speed of light = [tex]3\times 10^8\ \text{m/s}[/tex]
Propagation delay is given by distance by the speed of light
[tex]\dfrac{36000\times 10^3}{3\times 10^8}[/tex]
[tex]=0.12\ \text{s}\times 10^3[/tex]
[tex]=120\ \text{ms}[/tex]
The uplink propagation delay of the link is [tex]120\ \text{ms}[/tex].
I WILL MARK BRAINLIST!!!!
a person drops their phone. The phone's mass is 0.115 kilograms and the bridge is 15 meters tall. The instant the they dropped the phone, what was its mechanical energy?
1.725
16.9
200
A loan of $8.000 accumulates simple interest at an annual interest rate of 5%. After how many years does the value the loan become $9.200?
Heeeeelp please
Answer and I will give you brainiliest
Answer:
I think the answer is 63,
g Galileo's telescopes were not of high quality by modern standards. He was able to see the moons of Jupiter, but he never reported seeing features on Mars. Use the small-angle formula to find the angular diameter of Mars when it is closest to Earth. How does that compare with the maximum angular diameter of Jupiter
Answer:
θ₂/ θ₁= 2.58
Explanation:
In this exercise you are asked to compare the angular diameters of Mars and Jupiter. The angular diameter or angle in radians is
θ = D / R
where D is the diameter of the body, the distance from Earth to the body of interest and θ is angle in radians
The different distances are tabulated with respect to the Sun
Sun -Earth 1,496 10¹¹ m
Sun- Mars 2.28 10¹¹ m
Sun - Jupiter 7.78 10 m
The Radii of the planets are
Mars 3.37 10⁶ m
Jupiter 6.99 10⁷ m
let's calculate the angles for each body
a) Mars
θ₁ = 2r / R'
the distance from the ground is
R ’= D_planet - D_earth
R ’= 2.28 10¹¹ - 1.496 10¹¹
R ’= 0.784 10¹¹ m
let's calculate
θ₁ = [tex]\frac{2 \ 3.37 \ 10^6 }{0.784 \ 10^{11}}[/tex]
θ₁ = 8.6 10⁻⁵ radians
b) Jupiter
R ’= 7.78 10¹¹ - 1.496 10¹¹
R ’= 6.284 10¹¹ m
let's calculate
θ₂ = [tex]\frac{2 \ 6.99 \ 10^7}{6.284 \ 10^{11}}[/tex]
θ₂ = 2.22 10⁻⁴ radians
the ratio of the angular diameters is
θ₂/ θ₁ = [tex]\frac{2.22 \ 10^{-4}}{8.6 \ 10^{-5}}[/tex]
θ₂/ θ₁= 2.58
You throw a ball into the air as shown in the diagram. At what point does the ball have the most potential energy?
Answer:
Position X.
Explanation:
To know the correct answer to the question, it is important that we know the definition of potential energy.
Potential energy can be defined as the energy possessed by an object in relation to its position. Mathematically it can be expressed as:
PE = mgh
Where
PE => is the potential energy.
m => is the mass of the object.
g => is the acceleration due to gravity.
h => is the height to which the object is located.
Considering the formula for potential energy (i.e PE = mgh), we can see clearly that the potential energy (PE) is directly proportional to the height (h). This implies that the greater the height, the greater the potential energy and the smaller the height, the smaller the potential energy.
Considering the diagram given above, we can see that the greatest height attained by the ball is at position X. Thus, the ball will have the greatest potential energy at position X.
A ball is thrown horizontally to the right, from the top of a vertical cliff of height h. A wind blows horizontally to the left, and assume (simplistically) that the effect of the wind is to provide a constant force to the left, equal in magnitude to the weight of the ball. How fast should the ball be thrown so that it lands at the foot of the cliff
Answer:
v = [tex]\sqrt{\frac{y_o \ g}{2} }[/tex]
Explanation:
For this exercise we must use the projectile launch ratios, let's start by finding the time it takes to reach the bottom of the cliff, the initial vertical velocity is zero
y = y₀ + [tex]v_{oy}[/tex] t - ½ g t²
at the bottom of the cliff y = 0 and as the body is thrown horizontally the initial vertical velocity is zero
0 = y₀ + 0 - ½ g t²
t = [tex]\sqrt{2y_o/g}[/tex]
this time is the same as the horizontal movement.
Let's use Newton's second law to find the acceleration on this x-axis due to the force of the air
F = m aₓ
they tell us that force is equal to the weight of the body
-mg = maₓ
aₓ = -g
the sign indicates that the acceleration is to the left
we write the kinematics equation
x = x₀ + v₀ₓ t + ½ aₓ t²
They indicate that the final position is the foot of the cliff (x = 0), when it leaves the top it is at x₀ = 0 and has a velocity v₀ₓ = v
we substitute
0 = 0 + v t + ½ (-g) t²
v = ½ g t
we use the drop time
v = ½ g [tex]\sqrt{\frac{2yo}{g} }[/tex]
v = [tex]\sqrt{\frac{y_o \ g}{2} }[/tex]
An air-filled capacitor consists of two parallel plates, each with an area of A , separated by a distance d . A V potential difference is applied to these plates. What is the magnitude of the electric field between the plates
Answer:
E = V / d
Explanation:
In a charged capacitor an electric field is established that goes from the positive to the negative plate, this field is constant,
the potential difference is
D = E d
in this case they do not give the difference in potential V and the distance between the plates d
E = V / d
What is the speed of a cyclist that rides west 88 km in 32 minutes?
Answer:
The speed of the cyclist is 2.75 km/min.
Explanation:
Given
The distance d = 88 km Time t = 32 minutesTo determine
We need to find the speed of a cyclist.
In order to determine the speed of a cyclist, all we need to do is to divide the distance covered by a cyclist by the time taken to cover the distance.
Using the formula involving speed, time, and distance
[tex]s=\frac{d}{t}[/tex]
where
s = speed d = distance covered t = time takensubstitute d = 88, and t = 32 in the formula
[tex]s=\frac{d}{t}[/tex]
[tex]s=\frac{88}{32}[/tex]
Cancel the common factor 8
[tex]s=\frac{11}{4}[/tex]
[tex]s=2.75[/tex] km/min
Therefore, the speed of the cyclist is 2.75 km/min.
3. Describe how sound signals can be transmitted from a cell phone and received by another cell phone.
Create a labeled diagram that shows this process. (2 points)
Answer:
The sound energy travels through the air into the microphone and makes the diaphragm inside vibrate. The sound energy in your voice makes the air vibrate. Vibrating air carries the sound energy into the phone. The diaphragm in the mouthpiece microphone converts sound energy into electrical energy.
Explanation: Hope this helps! :)
Acceleration figures for cars usually are given as the number of seconds needed to go from 0.0 to 97 km/h. Convert 97 km/h into m/s.
Answer:
26.9444m/s
pls brainliest
Which statement about the sun's energy is correct?
It is entirely re-radiated back into space.
A part of it is destroyed by greenhouse gases.
A part of it is absorbed by atmospheric gases.
It makes Earth too hot for plants and animals to survive.
Answer:
The answer is (A)
Explanation:
We know this because The suns energy is entirely re-radiated back into space.
We know also that the answer is not (D) It makes Earth too hot for plants and animals to survive.
Atmospheric gases are gases located in the Earth's atmosphere
The green house effect is a natural process that warms the Earth's surface
I also know the answer because I took the test... FLVS exam 3.09 right?
I took it and got this question right... So i know you will! GOOD LUCK!!
Mark me brainlyest please:)
In reaching her destination, a backpacker walks with an average velocity of 1.19 m/s, due west. This average velocity results because she hikes for 5.96 km with an average velocity of 3.10 m/s, due west, turns around, and hikes with an average velocity of 0.744 m/s, due east. How far east did she walk
Answer:
x₂ = 4.455 m
Explanation:
The average speed is defined as the displacement traveled between the time interval
v_average = [tex]\frac{\Delta x}{\Delta t}[/tex]
in this case we have a first stop walking west at speed v = 3.10 m / s a distance of x = 5.96 km = 5.96 10³ m
Let's find the time it takes on this tour
v = x / t
t = x / v
t₁ = 5.96 10³ / 3.10
t₁ = 1.9226 10³ s
in a second to walk east at a speed of v₂ = 0.744 m / s
v₂ = x₂ / t₂
t₂ = x₂ / v₂
for full movement
let's assume that the eastward movement is positive
v =[tex]\frac{- x_1 + x_2}{t_1 +t_2}[/tex]
v = [tex]\frac{-x_1 +x_2}{t_1 + \frac{x_2}{t_2} }[/tex]
the only unknown term is the distance to the east. We replace and resolve
1.19 = [tex]\frac{-5.96 \ 10^3 + x_2}{1.92 \ 10^3 + \frac{x_2}{0.744} }[/tex]
1.19 (1.92 10³ + [tex]\frac{x_2}{0.744}[/tex]) = x₂ 1.92 10³ - 5.96 10³
2.2848 10³ + 1.599 x₂ = 1.92 10³ x₂ - 5.96 10³
x₂ (1.92 10³ - 1.599) = 2.2848 10³ + 5.96 10³
x₂ = 8.5448 10³ / 1.918 10³
x₂ = 4.455 m