SYNTHESIS The overall reaction for microbial conversion of glucose to L-glutamic acid is: C6H12O6 + NH3 +1.502 → C5H, NO4 + CO₂ + 3H₂O (glucose) (glutamic acid) What mass of oxygen is required t

Component G co: 212.8, Component G Co: -110.0, Component G: -155. The values given in the table represent the Gibbs free energy change (ΔG) for different components (co and Co) at the specified conditions (temperature, pressure).

The values are as follows:

Component G co: 212.8

Component G Co: -110.0

Component G: -155

The Gibbs free energy change (ΔG) is a thermodynamic property that indicates the spontaneity of a reaction or process. A negative ΔG value indicates a spontaneous process, while a positive ΔG value indicates a non-spontaneous process.

In this case, the given values for Component G co and Component G Co represent the Gibbs free energy changes associated with the corresponding components (co and Co) under the specified conditions of temperature and pressure.

The given table provides the values of the Gibbs free energy changes (ΔG) for the components co and Co at a temperature of 500K and different pressures. The values indicate the thermodynamic favorability of the corresponding processes. A positive value for Component G co (212.8) suggests a non-spontaneous process, while a negative value for Component G Co (-110.0) indicates a spontaneous process. The value Component G (-155) represents a generalized Gibbs free energy change without specifying a particular component.

To know more about energy , visit;

https://brainly.com/question/30829460

#SPJ11

a) The thermal efficiency of the cycle is approximately 37.63%.

b) The mass flow rate of the steam is approximately 520.86 kg/s.

c) The mass flow rate of the cooling water is approximately 361.98 kg/s.

a) The thermal efficiency of the cycle, b) the mass flow rate of the steam, and c) the mass flow rate of the cooling water can be determined for a steam power plant operating on a simple Rankine cycle. The net power output of the plant is given as 210 MW, and the operating conditions, isentropic efficiencies, and properties of steam and cooling water are provided.

To calculate the thermal efficiency of the cycle, we can use the formula:

Thermal Efficiency = (Net Power Output) / (Heat Input)

The heat input can be determined by considering the energy balance across the components of the Rankine cycle. By calculating the enthalpy differences between the inlet and outlet states of the turbine and the pump, we can determine the heat added in the boiler.

To find the mass flow rate of the steam, we can use the formula:

Mass Flow Rate of Steam = (Net Power Output) / (Specific Work Output of Turbine)

The specific work output of the turbine can be calculated using the isentropic efficiency of the turbine and the enthalpy difference between the inlet and outlet states of the turbine.

To determine the mass flow rate of the cooling water, we need to consider the energy balance across the condenser. The heat transferred in the condenser can be calculated by subtracting the enthalpy of the outlet water from the inlet water and multiplying it by the mass flow rate of the cooling water.

In summary, the thermal efficiency of the cycle, mass flow rate of the steam, and mass flow rate of the cooling water can be determined by analyzing the energy balances and properties of the components in the Rankine cycle, including the turbine, pump, boiler, and condenser.

To learn more about isentropic click here, brainly.com/question/13001880

#SPJ11

The amount of oxalic acid in the sample of rhubarb can be determined a solvent extraction process followed by analysis using a suitable analytical technique such as titration or spectrophotometry is required.

To determine the amount of oxalic acid in the rhubarb sample, a solvent extraction process can be performed. The process involves extracting the oxalic acid from the rhubarb using a suitable solvent. The extracted solution is then analyzed to measure the concentration of oxalic acid.

One common method for quantifying oxalic acid is titration. In this method, a known volume of the extracted solution is titrated with a standardized solution of a strong base, such as sodium hydroxide (NaOH). The reaction between oxalic acid and sodium hydroxide is stoichiometric, allowing the determination of the amount of oxalic acid present in the sample.

Another method is spectrophotometry, where the absorption of light by oxalic acid at a specific wavelength is measured. The absorbance is proportional to the concentration of oxalic acid, allowing its quantification.

To determine the amount of oxalic acid in the rhubarb sample, a solvent extraction process followed by analysis using a suitable analytical technique such as titration or spectrophotometry is required. These methods can provide quantitative measurements of oxalic acid concentration in the sample.

To know more about oxalic acid, visit:

https://brainly.com/question/14989723

#SPJ11

The change in internal energy in a closed system is equal to heat transferred when a reversible process takes place at constant temperature.

Thermodynamics is a scientific field that focuses on the study of the relationships between different forms of energy and how they are exchanged. A closed system is a system in which matter and energy are not exchanged with its surroundings.Internal energy refers to the sum of all forms of energy in a system, including kinetic and potential energy of the particles in the system.

Reversible process, on the other hand, is a process that can be reversed to return the system to its original state without any change to either the system or its surroundings.The change in internal energy is the difference between the final and initial internal energy. In a closed system, the change in internal energy is equal to heat transferred if the reversible process takes place at constant temperature. This is known as the first law of thermodynamics and is expressed mathematically as: ΔU = Qwhere ΔU is the change in internal energy, Q is the heat transferred, and the process is reversible and takes place at constant temperature. Therefore, option (c) temperature is correct.

Learn what is a closed system : https://brainly.com/question/2846657

#SPJ11

In the given scenario where steady state is achieved and the required conversions are initially achieved in both vessels but decrease with time while the reactor temperature remains constant.

There could be several reasons for this behavior: Catalyst deactivation: The reaction may be catalyzed by a specific catalyst that becomes deactivated over time. Catalyst deactivation could be due to various factors such as fouling, poisoning, or sintering. As the catalyst deactivates, its effectiveness in promoting the reaction decreases, leading to lower conversions. Possible solution: Regular catalyst regeneration or replacement can help maintain the activity of the catalyst and sustain the desired conversions. Accumulation of reaction by-products or impurities: The reaction may produce by-products or impurities that accumulate over time and hinder the progress of the reaction. These by-products can potentially react with the reactants or catalyst, leading to lower conversions.

Possible solution: Implementing suitable separation or purification techniques to remove the accumulated by-products or impurities can help maintain the desired conversions. Side reactions: In some cases, side reactions can occur alongside the desired reaction. These side reactions may consume reactants or intermediates, reducing the availability of reactants for the main reaction and resulting in lower conversions. Possible solution: Adjusting reaction conditions such as temperature, pressure, or catalyst composition can help minimize the occurrence of side reactions and maintain the desired conversions. It is crucial to investigate the specific cause of decreasing conversions in order to implement an appropriate solution. Detailed analysis of the reaction kinetics, catalyst behavior, and reaction products can provide insights into the underlying issues and guide the selection of the most suitable solution strategy.

To learn more about steady state click here: brainly.com/question/30760169

#SPJ11

We know the standard reduction potentials of the half-cells involved, so we can find the cell voltage and the spontaneous reaction. Thus;

The anode reaction is:

Pb(s) → Pb2+(aq) + 2e-

This is the oxidation half-reaction that occurs in the Pb half-cell.

The cathode reaction is:F2(g) + 2e- → 2F-(aq).

This is the reduction half-reaction that occurs in the F2 half-cell.

The spontaneous cell reaction is

:Pb(s) + F2(g) → Pb2+(aq) + 2F-(aq).

This is the combination of the oxidation and reduction half-reactions, with the electrons canceled out from both sides.

The cell voltage is 2.996 V The standard cell potential is calculated as follows:

standard cell potential = E°(reduction) - E°(oxidation)standard cell potential = 2.870 V - (-0.126 V)standard cell potential = 2.996 V, The cell voltage is positive, indicating that the reaction is spontaneous.

To know more about oxidation half-reaction visit;

https://brainly.com/question/12686471

#SPJ11

Based on the data provided, the calculated values are : 1. Ea = 0.18 V ; 2. The reaction is non-spontaneous. ; 3. 2 electrons are transferred. ; 4. Li+ is the oxidizing reactant. ; 5. Li metal is the anode. ; 6. ΔG° = -34.7 kJ/mol ; 7. K = 1.74 × 10⁻¹⁹ ; 8. ΔG = -34.8 kJ/mol ; 9. ΔG° = -34.7 kJ/mol ; 10. Ecell = 0.41 V ; 11. The reaction is spontaneous. ; 12. ΔG° = -79.1 kJ/mol ; 13. ΔG = -241.0 kJ/mol.

Given the following reaction : 2 Li+Ca→2 Li+Ca2

1. Since Eºcell = Eºcathode - Eºanode

Therefore, Eºcell = -2.87 V - (-3.05 V)

Eºcell = 0.18 V

2. Since Eºcell > 0, therefore the reaction is non-spontaneous.

3. Calculation of electrons transferred is based on the balanced equation : 2 Li + Ca → 2 Li+ + Ca2-

Thus, 2 electrons are transferred.

4. Oxidizing agent is the one that is reduced. Here Ca is reduced, so Li+ is oxidized. Therefore, Li+ is the oxidizing reactant.

5. The anode is the electrode at which oxidation occurs. Since Li+ is oxidized to Li, therefore Li metal is the anode.

6. ΔG° = -nFE°cell

where n = number of electrons transferred, F = Faraday constant = 96485 C/mol, E°cell = cell potential

Thus, ΔG° = -2 × 96485 C/mol × 0.18 V

ΔG° = -34728.6 J/mol = -34.7 kJ/mol

7.  ΔG° = -RT ln K

where R = 8.314 J/molK, T = 298 K

Thus, -34.7 kJ/mol = -8.314 J/molK × 298 K × ln K

ln K = -34.7 × 10³ J/mol / 8.314 J/molK × 298 K

ln K = -44.67K = 1.74 × 10⁻¹⁹

8. ΔG = ΔG° + RT ln Q

when Q = K, ΔG = ΔG° + RT ln K= -34.7 kJ/mol + 8.314 J/molK × 298 K × ln (1.74 × 10⁻¹⁹)

ΔG = -34.8 kJ/mol

9. ΔG° = -nFE°cell = -2 × 96485 C/mol × 0.18 V

ΔG° = -34728.6 J/mol = -34.7 kJ/mol

10. Ecell = Eºcell - (0.0592/n)log(Q)

Q = [Li+]²[Ca2+]

Ecell = 0.18 V - (0.0592/2)log[(10 M)² (1×10⁻²⁰ M)]

Ecell = 0.18 V - 0.0592 × 20 × (-20)

Ecell = 0.18 V + 0.23 V = 0.41 V

11. Since Ecell > 0, therefore the reaction is spontaneous.

12. ΔG° = -nFE°cell = -2 × 96485 C/mol × 0.41 V

ΔG° = -79062.2 J/mol = -79.1 kJ/mol

13. ΔG = ΔG° + RT ln Q

when Q = 1.0 × 10⁵, ΔG = ΔG° + RT ln K ;

ΔG = -79.1 kJ/mol + 8.314 J/molK × 298 K × ln (1.0 × 10⁵)ΔG = -79.1 kJ/mol - 161.9 kJ/mol

ΔG = -241.0 kJ/mol

Hence, the calculated values are : 1. Ea = 0.18 V ; 2. The reaction is non-spontaneous. ; 3. 2 electrons are transferred. ; 4. Li+ is the oxidizing reactant. ; 5. Li metal is the anode. ; 6. ΔG° = -34.7 kJ/mol ; 7. K = 1.74 × 10⁻¹⁹ ; 8. ΔG = -34.8 kJ/mol ; 9. ΔG° = -34.7 kJ/mol ; 10. Ecell = 0.41 V ; 11. The reaction is spontaneous. ; 12. ΔG° = -79.1 kJ/mol ; 13. ΔG = -241.0 kJ/mol.

To learn more about oxidizing agent :

https://brainly.com/question/14041413

#SPJ11

a (i) The most common method for synthesizing sodalite is through hydrothermal synthesis. In this method, a reaction mixture containing appropriate sources of sodium (Na), aluminum (Al), and silicon (Si) is sealed in a vessel and heated at high temperature and pressure.

The reagents used for synthesizing sodalite typically include sodium hydroxide (NaOH), aluminum hydroxide (Al(OH)3), and silica (SiO2) sources such as sodium silicate or colloidal silica. The reaction proceeds under alkaline conditions, resulting in the formation of sodalite crystals.

(ii) The role of the ammonium salt, [(CH3)3(CH3(CH2)17)N]CI, in the synthesis of a zeolite member is likely to act as a structure-directing agent or templating agent.

Zeolites are crystalline materials with well-defined porous structures, and the addition of organic compounds, known as structure-directing agents or templates, helps to guide the formation of specific zeolite structures. These organic compounds are typically large, organic cations that fit into the cavities of the forming zeolite structure and influence the crystal growth and pore size distribution. In this case, the ammonium salt serves as a template for the synthesis of the desired zeolite member, helping to direct the formation of its specific structure.

The reaction of sodalite involves hydrothermal synthesis using reagents such as sodium hydroxide, aluminum hydroxide, and silica sources. The addition of the ammonium salt in the synthesis of another zeolite member serves as a structure-directing agent, guiding the formation of the desired zeolite structure.

To know more about reaction, visit :

https://brainly.com/question/30464598

#SPJ11

In the industrial wastewater treatment process, the selection of an appropriate treatment technique is crucial to effectively remove toxicants, pollutants, and pathogens from the wastewater.

For an industry in Oman, the activated sludge process is a suitable treatment technique for industrial wastewater. This process operates by introducing a mixed culture of microorganisms (activated sludge) into the wastewater, allowing them to biologically decompose the organic matter present. The wastewater is mixed with the activated sludge in an aeration tank, providing oxygen and creating an environment where microorganisms can thrive. The microorganisms metabolize the organic matter, converting it into carbon dioxide, water, and microbial biomass.

The activated sludge process offers several advantages. Firstly, it achieves high removal efficiency for organic matter, suspended solids, and nutrients. This results in significant improvement in water quality, making it suitable for discharge into water bodies or for reuse in agricultural applications. Secondly, the process is versatile and adaptable to different wastewater characteristics, allowing it to handle a wide range of industrial effluents. Furthermore, the activated sludge process can be easily expanded or modified to accommodate changes in wastewater volume or composition.

Despite its advantages, the activated sludge process has certain disadvantages. Energy consumption is a major drawback, as the aeration of the wastewater requires significant amounts of energy. Additionally, the process generates excess sludge, which requires proper management and disposal. The disposal of excess sludge can be challenging and may require additional treatment or disposal methods.

To optimize the activated sludge process in the selected industry, it is recommended to closely monitor and control the process parameters such as aeration rate, sludge age, and nutrient dosage. This will ensure optimal performance and minimize energy consumption. Additionally, implementing complementary treatment methods such as advanced oxidation processes or membrane filtration can help address specific pollutants that may not be effectively removed by the activated sludge process alone. Regular monitoring and maintenance of the treatment system are essential to ensure its long-term efficiency and effectiveness in treating industrial wastewater.

To learn more about microorganisms click here, brainly.com/question/9004624

#SPJ11

A positive azeotrope is a mixture of two or more components that exhibits a higher boiling point or lower vapor pressure than any of its individual components. In other words, the vapor phase composition of the azeotropic mixture is different from the composition of the liquid phase. This results in the formation of a constant boiling mixture, where the composition of the vapor and liquid phases remain constant during distillation.

Example of Positive Azeotrope: Ethanol-Water Mixture

The ethanol-water system forms a positive azeotrope at approximately 95.6% ethanol and 4.4% water by weight. This means that when this mixture is distilled, the vapor phase will have the same composition as the liquid phase, resulting in a constant boiling mixture.

Negative Azeotrope:

A negative azeotrope is a mixture of two or more components that exhibits a lower boiling point or higher vapor pressure than any of its individual components. Unlike positive azeotropes, the vapor and liquid phases of a negative azeotropic mixture have the same composition.

Example of Negative Azeotrope: Acetone-Chloroform Mixture

The acetone-chloroform system forms a negative azeotrope at approximately 75.5% acetone and 24.5% chloroform by weight. During distillation, the vapor and liquid phases will have the same composition, leading to the formation of a constant boiling mixture.

Separation of Complex Mixtures: Equilibrium distillation allows for the separation of complex mixtures containing multiple components with different boiling points or vapor pressures.

High Purity Products: Equilibrium distillation can achieve high purity products by selecting appropriate operating conditions and carefully designing the distillation column.

Versatility: Equilibrium distillation can be applied to a wide range of industrial processes, making it a versatile separation technique.

Disadvantages of Equilibrium Distillation:

Equilibrium distillation offers advantages such as the separation of complex mixtures and the production of high purity products. However, it has drawbacks including high energy consumption, capital and operational costs, and limitations when dealing with azeotropic systems. The selection of distillation techniques should consider the specific mixture and separation requirements to achieve the desired outcomes efficiently and economically.

To know more about azeotrope visit:

https://brainly.com/question/20373141

#SPJ11

After losing an electron from the atom the net charge on the atom is now +4.

An atom's atomic number, which is constant, is determined by the number of protons it contains. The atom in question possesses 22 protons, making it an atom with the atomic number 22.

Because there are now more protons (positive charges) than electrons (negative charges), when an atom loses an electron, it becomes positively charged. The atom once had 19 electrons, but after losing one, it now only possesses 18.

Subtracting the number of electrons from the number of protons yields the atom's net charge. The net charge in this instance is +4 (22 protons minus 18 electrons = +4).

The atom's net charge is now +4  

To know more about a net charge on atoms click here;

https://brainly.com/question/30938481

After performing the calculations, we can obtain the molarity of the Ba(OH)2 solution.

To calculate the molarity of the Ba(OH)2 solution, we need to use the stoichiometry of the reaction between Ba(OH)2 and benzoic acid.

Given:

Volume of Ba(OH)2 solution = 67.06 mL

Mass of benzoic acid = 0.6929 g

Molecular weight of benzoic acid (C6H5COOH) = 122.12 g/mol

Volume of HCl used in back-titration = 5.4248 mL

Molarity of HCl = 0.02250 M

First, let's calculate the number of moles of benzoic acid:

moles of benzoic acid = mass / molecular weight

moles of benzoic acid = 0.6929 g / 122.12 g/mol

Next, let's determine the number of moles of Ba(OH)2 that reacted with the benzoic acid. From the balanced equation, we know that 1 mole of benzoic acid reacts with 2 moles of Ba(OH)2.

moles of Ba(OH)2 = 2 * moles of benzoic acid

Now, let's calculate the volume of HCl that reacted with the excess Ba(OH)2:

moles of HCl = molarity * volume

moles of HCl = 0.02250 M * 5.4248 mL / 1000 (convert mL to L)

Since the reaction between Ba(OH)2 and HCl occurs in a 1:2 ratio, the moles of HCl that reacted are equal to half the moles of Ba(OH)2 that reacted:

moles of HCl = 0.5 * moles of Ba(OH)2

Now, let's determine the total moles of Ba(OH)2 in the solution:

total moles of Ba(OH)2 = moles of Ba(OH)2 that reacted + moles of HCl

Finally, we can calculate the molarity of the Ba(OH)2 solution:

molarity = total moles of Ba(OH)2 / volume of Ba(OH)2 solution (L)

After performing the calculations, we can obtain the molarity of the Ba(OH)2 solution.

Note: The volume of the Ba(OH)2 solution needs to be converted to liters.

Please note that the given volume of Ba(OH)2 solution is relatively small compared to the volume of the back-titration with HCl. This suggests that the Ba(OH)2 solution is in excess and the HCl is the limiting reagent in the reaction.

To know more about HCL related question visit:

https://brainly.com/question/30233723

#SPJ11

the new flow rate after changing the rpm of the pump from 1800 to 3600 is 20 m³/s.

To calculate the new flow rate when changing the rpm of the pump, we can use the concept of pump affinity laws. The pump affinity laws state the relationship between the pump speed (N), flow rate (Q), head (H), and power (P) of a centrifugal pump.

The pump affinity laws are as follows:

1. Flow Rate: Q2 / Q1 = (N2 / N1)

2. Head: H2 / H1 = (N2 / N1)^2

3. Power: P2 / P1 = (N2 / N1)^3

Given that the initial rpm of the pump is 1800 and we want to change it to 3600, we can calculate the new flow rate (Q2) using the flow rate formula.

Q1 is the initial flow rate, which is known. Let's assume it as 10 m³/s.

Q2 / 10 = (3600 / 1800)

Q2 = 20 m³/s

Therefore, the new flow rate after changing the rpm of the pump from 1800 to 3600 is 20 m³/s.

4) To determine if the pump will cavitate, we can compare the available net positive suction head (NPSHa) with the required net positive suction head (NPSHr).

NPSHa represents the pressure head available at the pump suction, while NPSHr represents the minimum pressure head required to prevent cavitation.

Given: Hpv = 0.3 m (vapor pressure head)

If NPSHa is greater than or equal to NPSHr, cavitation will not occur.

However, since the NPSHa and NPSHr values are not provided in the problem, we cannot determine if the pump will cavitate without additional information. NPSHa depends on factors such as system pressure, elevation, pipe size, and fluid properties, while NPSHr is specific to the pump design and can be obtained from the manufacturer's specifications.

To know more about RPM related question visit:

https://brainly.com/question/32283379

#SPJ11

a) Bioreactor design considerations: volume, oxygen transfer rate, mixing, temperature control, pH control, and sterilization.

b) Important parameters for stirred-tank bioreactor: agitation speed (mixing) and foam control.

a) Six process engineering parameters to consider in designing a bioreactor:

The size of the bioreactor, including the working volume and maximum capacity, determines the scale of production.

Adequate oxygen supply is crucial for aerobic bioprocesses, and the design should ensure efficient oxygen transfer to support cell growth and metabolism.

Proper mixing and agitation ensure uniform distribution of nutrients, gases, and temperature throughout the bioreactor, promoting optimal growth and productivity.

Maintaining the desired temperature range is important for the growth and activity of microorganisms or cells, and the bioreactor should have effective temperature control mechanisms.

pH affects enzyme activity, product formation, and cell viability, so the bioreactor design should include provisions for accurate pH control.

Proper sterilization and cleaning procedures and equipment must be incorporated into the bioreactor design to ensure aseptic conditions and prevent contamination.

b) Two important parameters and their effects on stirred-tank bioreactor operation:

The agitation speed determines the mixing intensity in the bioreactor.

Too low agitation may lead to poor mixing, uneven nutrient distribution, and inadequate oxygen transfer, while excessive agitation can cause shear stress and damage cells or reduce cell viability.

Stirred-tank bioreactors often experience foaming due to the production of surfactants by microorganisms or the presence of high protein concentrations.

Excessive foam can hinder oxygen transfer and mixing, leading to reduced bioreactor performance.

Effective foam control mechanisms, such as antifoam agents or foam level monitoring, should be implemented.

Learn more about bioreactors here:

https://brainly.com/question/30975154

#SPJ11

When two charged nanoparticles are present in an aqueous solution, several interactions contribute to their stability and prevent agglomeration. The interactions can be categorized into electrostatic repulsion, steric hindrance, and hydration effects. Here's a detailed explanation of each interaction:

Overall, the combination of electrostatic repulsion, steric hindrance, and hydration effects leads to the stabilization of charged nanoparticles in aqueous solution. By introducing charges to the nanoparticles and carefully controlling the surface chemistry, it is possible to enhance these interactions and achieve long-term stability, preventing nanoparticle agglomeration and ensuring their dispersed state in solution.

To know more about aqueous solution, visit :

https://brainly.com/question/1382478

#SPJ11

Q3

(a) By implementing this feed forward control configuration, the distillation column can effectively maintain the production of distillate stream with 96 mole % pentane, even in the presence of changes in the feed flow rate.

(b) the estimated thermometer reading at 3 minutes is approximately 84.34°C.
(c) The final control element in a control system is responsible for executing the control actions based on the output from the controller.

(a) To maintain the production of distillate stream with 96 mole % pentane in the presence of changes in the feed composition, a feed forward control configuration can be implemented. Feed forward control involves measuring the disturbance variable (in this case, the feed flow rate) and adjusting the manipulated variable (in this case, the reflux or reboiler heat duty) based on the known relationship between the disturbance variable and the process variable.

The steps to develop a feed forward control configuration for the distillation column are as follows:

Measure the feed flow rate and the composition of the feed mixture (n-pentane and n-hexane).

Use the known relationship between the feed flow rate and the distillate composition to determine the required adjustment in the manipulated variable. This relationship can be established through process modeling or empirical data.

Calculate the necessary change in the reflux or reboiler heat duty based on the deviation from the desired distillate composition.

Adjust the reflux or reboiler heat duty accordingly to maintain the desired distillate composition.

By implementing this feed forward control configuration, the distillation column can effectively maintain the production of distillate stream with 96 mole % pentane, even in the presence of changes in the feed flow rate.

(b) The reading of the first-order mercury thermometer system at 3 minutes can be estimated by considering the time constant and the temperature difference between the initial and final states.

The time constant of the thermometer system is given as 2 minutes, which means the system takes approximately 2 minutes to reach 63.2% of the final temperature.

Since the thermometer is initially maintained at 60°C and is then immersed in a bath maintained at 100°C at t = 0, we need to calculate the temperature at 3 minutes.

After 2 minutes, the thermometer system would have reached approximately 63.2% of the temperature difference between the initial and final states. Therefore, the temperature would be: 60°C + 0.632 * (100°C - 60°C) = 68.16°C

At 3 minutes, an additional 1 minute has passed since the 2-minute mark. Considering the time constant, we can estimate that the system would have reached approximately 86.5% of the temperature difference between the initial and final states. Therefore, the estimated temperature at 3 minutes would be: 68.16°C + 0.865 * (100°C - 60°C) = 84.34°C

Therefore, the estimated thermometer reading at 3 minutes is approximately 84.34°C.

(c) The final control element in a control system is responsible for executing the control actions based on the output from the controller. It is the physical device that directly interacts with the process to regulate the process variable and maintain it at the desired setpoint.

The function of the final control element is to modulate the flow, pressure, or position to manipulate the process variable. It takes the control signal from the controller and converts it into an action that affects the process.

Examples of final control elements include control valves, variable speed drives, motorized dampers, and variable pitch fans. These devices can adjust the flow of fluids, regulate the speed of motors, control the position of dampers, or change the pitch of fan blades to achieve the desired process control.

The final control element plays a crucial role in maintaining the stability and performance of the control system by accurately translating the control signal into the appropriate action on the process variable. It ensures that the process variable remains within the desired range and responds effectively to changes in the setpoint or disturbance variables.

To know more about pentane , visit :

https://brainly.com/question/32575022

#SPJ11

For the given data (1) The formulas for the three pollutants are CO, SO2, and NO2 respectively. (2a) The balanced chemical equation for the incomplete combustion of methane is : CH4 + 1.5 O2 → CO + 2 H2O ; (2b) Mass of CO produced = 1,133.25 g; (3a) The balanced chemical equations : N2(g) + O2(g) → 2NO(g)NO(g) + 0.5 O2(g) → NO2(g) ; (3b) These reactions are neither synthesis nor decomposition reactions ; (3c) The moles of nitrogen monoxide produced is 13.28 mol. ; (3d) Mass of NO2 = 305.99 g.

1. The formulas for the three pollutants that are binary molecular compounds, carbon monoxide, sulfur dioxide and nitrogen dioxide are CO, SO2, and NO2 respectively.

2.a. The balanced chemical equation for the incomplete combustion of methane is : CH4 + 1.5 O2 → CO + 2 H2O

b. Using the balanced chemical equation given in part a, 1 mol of CH4 gives 1 mol of CO.

The molar mass of CH4 is 16.04 g/mol.

Therefore, 650.0 g of CH4 corresponds to :

650.0 g CH4 x (1 mol CH4 / 16.04 g CH4) = 40.53 mol CH4

From the balanced chemical equation, 1 mol of CH4 gives 1 mol of CO.

Therefore, 40.53 mol of CH4 gives : 40.53 mol CH4 x (1 mol CO / 1 mol CH4) = 40.53 mol CO

The mass of carbon monoxide produced can be calculated as follows :

Mass of CO = number of moles of CO x molar mass of CO = 40.53 mol CO x 28.01 g/mol= 1,133.25 g (rounded to four significant figures)

3.a. The balanced chemical equations for the two reactions described in this problem are :

N2(g) + O2(g) → 2NO(g)NO(g) + 0.5 O2(g) → NO2(g)

b. These reactions are neither synthesis nor decomposition reactions. The first equation describes a combination reaction and the second equation describes a disproportionation reaction.

c. From the balanced chemical equation given in part a, 1 mol of nitrogen monoxide is produced from 1 mol of oxygen and 1 mol of nitrogen. The molar mass of oxygen is 32.00 g/mol. Therefore, 425 g of oxygen corresponds to :

425 g O2 x (1 mol O2 / 32.00 g O2) = 13.28 mol O2

From the balanced chemical equation, 1 mol of nitrogen monoxide is produced from 1 mol of oxygen.

Therefore, 13.28 mol of oxygen gives :

13.28 mol O2 x (1 mol NO / 1 mol O2) = 13.28 mol NO

The moles of nitrogen monoxide produced is 13.28 mol.

d.  From the balanced chemical equation given in part a, 1 mol of nitrogen monoxide reacts with 0.5 mol of oxygen to produce 1 mol of nitrogen dioxide.

The molar mass of nitrogen dioxide is 46.01 g/mol.

Therefore, 13.28 mol of nitrogen monoxide corresponds to :

13.28 mol NO x (0.5 mol O2 / 1 mol NO) x (1 mol NO2 / 1 mol O2) = 6.64 mol NO2

The mass of nitrogen dioxide produced is :

Mass of NO2 = number of moles of NO2 x molar mass of NO2= 6.64 mol NO2 x 46.01 g/mol= 305.99 g

Thus, (1) The formulas for the three pollutants are CO, SO2, and NO2 respectively. (2a) The balanced chemical equation for the incomplete combustion of methane is : CH4 + 1.5 O2 → CO + 2 H2O ; (2b) Mass of CO produced = 1,133.25 g; (3a) The balanced chemical equations : N2(g) + O2(g) → 2NO(g)NO(g) + 0.5 O2(g) → NO2(g) ; (3b) These reactions are neither synthesis nor decomposition reactions ; (3c) The moles of nitrogen monoxide produced is 13.28 mol. ; (3d) Mass of NO2 = 305.99 g.

To learn more about decomposition reaction :

https://brainly.com/question/27300160

#SPJ11

(a) The iron-carbon diagram, also known as the iron-carbon phase diagram, illustrates the relationship between the composition of iron-carbon alloys and their corresponding phases at equilibrium. The diagram shows the percentage of carbon on the x-axis and the temperature on the y-axis. Three distinct phases of iron can be observed on this diagram: ferrite, austenite, and cementite.

Ferrite:

Ferrite is the purest form of iron, containing a small amount of carbon (up to about 0.022%). It has a body-centered cubic (BCC) crystal structure. Ferrite is a relatively soft and ductile phase, and it is the primary phase in low-carbon steels.

Austenite:

Austenite is a high-temperature phase of iron that exists between approximately 0.022% and 2.11% carbon. It has a face-centered cubic (FCC) crystal structure. Austenite is non-magnetic and has higher strength and hardness compared to ferrite. It is present in higher carbon steels and is stable at elevated temperatures.

Cementite:

Cementite, also known as iron carbide (Fe3C), is a hard and brittle phase that forms when the carbon content exceeds 2.11%. It has an orthorhombic crystal structure. Cementite is a constituent of certain high-carbon steels and cast irons.

(b) Steel is defined as an alloy of iron and carbon with a carbon content ranging from 0.02% to 2.11%. The specific percentage of carbon in steel determines its properties, such as strength, hardness, and ductility.

For example, low-carbon steels (up to 0.3% carbon) are relatively soft, malleable, and easily weldable. They find applications in construction, automotive bodies, and general engineering.

Medium-carbon steels (0.3% to 0.6% carbon) have increased strength and hardness compared to low-carbon steels. They are often used for forging, axles, and machinery components.

High-carbon steels (0.6% to 1.4% carbon) possess excellent hardness and wear resistance but are less ductile. They are commonly utilized in cutting tools, springs, and high-strength wires.

The iron-carbon diagram depicts the phases of iron as a function of carbon content and temperature. Ferrite, austenite, and cementite are the three primary phases present in iron-carbon alloys. By controlling the carbon content within the defined range, steel can be tailored to possess various mechanical properties suitable for a wide range of applications.

To know more about alloys , visit;

https://brainly.com/question/31389764

#SPJ11

The standard enthalpy change for the combustion of ethanol is -1300 kJ/mol, which means that the reaction is exothermic.

The balanced chemical equation for the combustion of ethanol is CH3CH2OH (l) + 3 O2 (g) → 2 CO2 (g) + 3 H2O (g). The enthalpy change (ΔH) associated with the combustion of one mole of ethanol is the difference between the sum of the standard enthalpies of formation of the products (CO2 and H2O) and the sum of the standard enthalpies of formation of the reactants (ethanol and O2).

Standard enthalpy of formation (ΔHf°) is the enthalpy change that occurs when one mole of a compound is formed from its elements in their standard states under standard conditions (298 K and 1 atm).

The standard enthalpies of formation of ethanol, CO2, and H2O are as follows :

ΔHf° (C2H5OH, l) = -277.69 kJ/mol ;

ΔHf° (CO2, g) = -393.51 kJ/mol ;

ΔHf° (H2O, g) = -241.82 kJ/mol

The standard enthalpy of formation of O2 is zero (0 kJ/mol) because it is an elemental form.

ΔH°rxn = [∑ΔHf°(products)] - [∑ΔHf°(reactants)]

ΔH°rxn = [2(-393.51 kJ/mol) + 3(-241.82 kJ/mol)] - [-277.69 kJ/mol + 3(0 kJ/mol)]

ΔH°rxn = -1301.46 kJ/mol ≈ -1300 kJ/mol

Therefore, the standard enthalpy change for the combustion of ethanol is -1300 kJ/mol, which means that the reaction is exothermic.

To learn more about standard enthalpy change :

https://brainly.com/question/14047927

#SPJ11

The complete ionic equation is:2K⁺(aq) + CO₃²⁻(aq) + Mg²⁺(aq) + 2NO₃⁻(aq) → MgCO₃(s) + 2K⁺(aq) + 2NO₃⁻(aq) and the net ionic equation is:Mg²⁺(aq) + CO₃²⁻(aq) → MgCO₃(s)The net ionic equation can be further simplified by omitting the spectator ions.

The reaction between aqueous solutions of potassium carbonate and magnesium nitrate yields solid magnesium carbonate and a solution of potassium nitrate. The net ionic equation for this reaction can be determined by following these steps:Step 1: Write the balanced chemical equation K₂CO₃(aq) + Mg(NO₃)₂(aq) → MgCO₃(s) + 2KNO₃(aq)

Step 2: Rewrite the balanced chemical equation with all the strong electrolytes shown as ionsK⁺(aq) + CO₃²⁻(aq) + Mg²⁺(aq) + 2NO₃⁻(aq) → MgCO₃(s) + 2K⁺(aq) + 2NO₃⁻(aq)

Step 3: Cross out the spectator ions, the ions that appear on both sides of the equationCO₃²⁻(aq) + Mg²⁺(aq) → MgCO₃(s)Step 4: Write the net ionic equation Mg²⁺(aq) + CO₃²⁻(aq) → MgCO₃(s) Magnesium carbonate is a white solid with the formula MgCO₃. It is insoluble in water and is precipitated from the aqueous solution. Potassium nitrate, on the other hand, is soluble in water and exists as an aqueous solution.

Hence, the complete ionic equation is:2K⁺(aq) + CO₃²⁻(aq) + Mg²⁺(aq) + 2NO₃⁻(aq) → MgCO₃(s) + 2K⁺(aq) + 2NO₃⁻(aq) and the net ionic equation is:Mg²⁺(aq) + CO₃²⁻(aq) → MgCO₃(s)The net ionic equation can be further simplified by omitting the spectator ions.

Learn more about aqueous solution here,

https://brainly.com/question/19587902

#SPJ11

Oxidation is a reaction in which a compound loses electrons. Oxidation and reduction occur simultaneously, and the process is referred to as redox. Methane, or CH4, is oxidized in the atmosphere by A. hydroxyl (OH) radicals. When sunlight strikes the troposphere, hydroxyl radicals are formed.

The presence of hydroxyl radicals is required to oxidize CH4 in the troposphere.

To oxidize CH4 in the troposphere, A. the presence of hydroxyl radicals and light is required.

Methane (CH4) is a potent greenhouse gas that is rapidly increasing in the atmosphere due to anthropogenic activities such as fossil fuel use, agriculture, and waste management. It has a global warming potential of around 28 times that of CO2 over a 100-year period and is responsible for about 20% of the greenhouse effect. CH4 is oxidized in the atmosphere by hydroxyl (OH) radicals, which are formed when sunlight strikes the troposphere. CH4 reacts with OH radicals to produce water vapor (H2O) and carbon dioxide (CO2). The oxidation of CH4 by OH is a critical process that controls the atmospheric lifetime of CH4 and, as a result, its contribution to climate change. Therefore, the presence of hydroxyl radicals is required to oxidize CH4 in the troposphere. It is also important to note that light is also necessary for this oxidation to occur.

To know more about Oxidation visit:

https://brainly.com/question/13182308

#SPJ11

The procedure used for casting flat rolled products is called continuous casting, and it is achieved through a process where molten metal is solidified into a semi-finished product (such as a slab or billet) without interruption as it moves through a series of water-cooled rollers.

Continuous casting is a process where molten metal is solidified into a semi-finished product without interruption as it moves through a series of water-cooled rollers. The continuous casting process is commonly used for casting flat rolled products, like sheets, plates, and strips, as well as long products, like billets and slabs, which can be used in a wide range of industries, from construction and manufacturing to transportation and packaging.

The continuous casting process is achieved through a series of steps, which may vary depending on the specific application. However, the general steps for continuous casting are as follows:

1. Preparing the mold: The mold, also known as the caster, is prepared by coating it with a lubricant and water to prevent the metal from sticking to it.

2. Pouring the metal: The molten metal is poured into the caster at a controlled rate to ensure consistent cooling and solidification.

3. Solidifying the metal: As the molten metal moves through the caster, it is cooled and solidified into a semi-finished product, such as a slab or billet.

4. Continuous rolling: The semi-finished product is then rolled through a series of water-cooled rollers to further reduce its thickness and refine its properties.

5. Cutting the product: Finally, the continuous rolled product is cut to the desired length and packaged for shipment.

Know more about continuous casting here:

https://brainly.com/question/14251688

#SPJ11

A capillary tube with an internal diameter of approximately 0.577 mm should be used. The ratio of the new mass flow rate to the old one will be nine times larger.

In laminar flow, the Hagen-Poiseuille equation describes the relationship between flow rate, pressure drop, viscosity, tube length, and tube diameter. According to this equation, the flow rate (Q) is directly proportional to the fourth power of the tube radius (r^4) and inversely proportional to the tube length (L) and viscosity (η).

To triple the fluid velocity, we need to increase the flow rate by a factor of 3. This can be achieved by increasing the radius to the power of 4 by a factor of 3. Therefore, we can set up the following equation:

(3Q) = (r^4 / R^4) * (L / L) * (η / η)

Where R is the original radius, Q is the original flow rate, and L and η are the same for both tubes. Simplifying the equation, we get:

r^4 = 3 * R^4

Taking the fourth root of both sides, we find:

r ≈ R * (3)^0.25 ≈ 0.577 * R

Hence, to triple the fluid velocity, we should use a tube with an internal diameter of approximately 0.577 times the original diameter.

The mass flow rate (m) is given by the equation:

m = ρ * Q * A

Where ρ is the density of the fluid, Q is the flow rate, and A is the cross-sectional area of the tube. Since the density and the cross-sectional area remain constant, the mass flow rate is directly proportional to the flow rate. Therefore, the ratio of the new mass flow rate (m') to the old one (m) will be the same as the ratio of the new flow rate (Q') to the old one (Q). Since we are tripling the flow rate, the ratio of the new mass flow rate to the old one will be nine times larger.

To learn more about capillary tube click here, brainly.com/question/30097496

#SPJ11

Biodiesel is indeed an alkylester (RCOOR') obtained from fat, and it possesses combustion characteristics similar to diesel fuel. However, biodiesel is known to be more stable, non-toxic, and less susceptible to microbial decomposition due to its relatively high flash point.

Biodiesel is produced through a chemical process called transesterification, where fats or vegetable oils are reacted with an alcohol (usually methanol or ethanol) in the presence of a catalyst, such as sodium hydroxide or potassium hydroxide.

This reaction results in the formation of alkyl esters, which are the main components of biodiesel.

The combustion characteristics of biodiesel are similar to those of conventional diesel fuel, which make it a suitable alternative for diesel engines without requiring significant engine modifications.

Biodiesel has a higher flash point compared to petroleum diesel, meaning it requires a higher temperature to ignite. This property enhances safety and reduces the risk of accidental fires.

Furthermore, biodiesel is considered stable because it has a lower propensity to degrade or oxidize over time compared to conventional diesel fuel. This stability ensures that biodiesel can be stored for longer periods without significant deterioration in quality.

Biodiesel is also recognized for its non-toxic nature. It is biodegradable and poses fewer health risks than petroleum-based diesel fuel. In case of a spill or leakage, biodiesel can be less harmful to the environment and human health.

In summary, biodiesel is an alkylester obtained from fat through the transesterification process. It exhibits combustion characteristics similar to diesel fuel but offers several advantages, including stability, non-toxicity, and a relatively high flash point.

These properties make biodiesel a viable and environmentally friendly alternative to petroleum diesel fuel, contributing to the diversification of energy sources and reducing the environmental impact associated with traditional fossil fuels.

CH₂-OCOR¹ CH-OCOR² + 3CH₂OH CH- CH₂-OCOR³ Triglyceride Methanol A + 3M Catalyst CH₂OH R¹COOCH3 CHOH + R³COOCH3 CH₂OH R³COOCH3 Glycerol Methyl esters G + 3P Triglyceride + R¹OH Diglyceride + R¹OH Monoglyceride + R¹OH Diglyceride + RCOOR¹ Monoglyceride + RCOOR¹ Glycerol + RCOOR¹ A+MB+P [1] B+MC+P [2] C+M G+P [3] temp (°C) 45 55 65 time (min) 5 0.94 0.89 0.80 10 0.89 0.81 0.67 15 0.84 0.74 0.57 20 0.80 0.67 0.50 25 0.76 0.63 0.45 30 0.73 0.58 0.40 tem(C) 45 55 65 60 rate constant (L/(mol min)) kl k2 Obtained from question 0.0255 Obtained from question 0.0510 Obtained from question 0.0965 Obtained from question ? k3 0.0881 0.141 0.218 ?

To learn more about alkylester, visit    

https://brainly.com/question/28203011

#SPJ11

The composition of gases at the output of the first bed (Bed I) of catalyst is as follows:CI SO2: (5+n) % volume,CI O2: (8+n) % volume,CISO3: 0 % volume,CIN2: (87-2n) % volume

Based on the given information, we have the composition of gases resulting from the pyrite burning:

Cso2: (5+n) %

Co2: (8+n) %

CN2: (87-2n) %

To calculate the composition of gases at the output of Bed I of the catalyst, we need to consider the reactions occurring in the catalyst bed. From the given information, it seems that the catalyst is converting SO2 to SO3, which results in the absence of CISO3 at the output of Bed I.

Assuming complete conversion of SO2 to SO3, we can determine the remaining composition as follows:

CI SO2: (5+n) % volume (unchanged)

CI O2: (8+n) % volume (unchanged)

CISO3: 0 % volume (absent due to conversion)

CIN2: (87-2n) % volume (unchanged)

The composition of gases at the output of the first bed (Bed I) of the catalyst includes unchanged CI SO2, CI O2, and CIN2. However, CISO3 is absent due to the conversion of SO2 to SO3. The specific values of n and the detailed reactions occurring in the catalyst bed are not provided, so further analysis and calculations are required to obtain the exact composition of the gases.

To know more about gases visit:

brainly.com/question/1369730

#SPJ11

If more [tex]H_{2}[/tex] and [tex]N_{2}[/tex] are added to the reaction 3[tex]H_{2}[/tex] + N2 → 2[tex]NH_{3}[/tex] after it reaches equilibrium, two events will occur Shift in Equilibrium and Increased Yield of [tex]NH_{3}[/tex]

1. Shift in Equilibrium: According to Le Chatelier's principle, when additional reactants are added, the equilibrium will shift in the forward direction to consume the added reactants and establish a new equilibrium. In this case, more [tex]NH_{3}[/tex] will be produced to counteract the increase in [tex]H_{2}[/tex] and [tex]N_{2}[/tex].

2. Increased Yield of [tex]NH_{3}[/tex]: The shift in equilibrium towards the forward reaction will result in an increased yield of [tex]NH_{3}[/tex]. As more [tex]H_{2}[/tex] and [tex]N_{2}[/tex] are added, the reaction will favor the production of [tex]NH_{3}[/tex] to maintain equilibrium. This will lead to an increase in the concentration of [tex]NH_{3}[/tex] compared to the initial equilibrium state.

It is important to note that the equilibrium position will ultimately depend on factors such as the concentrations of [tex]H_{2}[/tex], [tex]N_{2}[/tex], and [tex]NH_{3}[/tex], as well as the temperature and pressure of the system. By adding more reactants, the equilibrium will adjust to achieve a new balance, favoring the formation of more [tex]NH_{3}[/tex].

Know more about Le Chatelier's principle here:

https://brainly.com/question/2943338

#SPJ8

Answer a)  32,000 µg/m³

Solution a) To calculate the concentration of carbon monoxide (CO) in micrograms per cubic meter (µg/m³) under standard conditions of 1 atm and 25 °C, we will need to use the ideal gas law. The ideal gas law equation is given as:

PV = nRT

where:P = pressure

V = volume

n = amount of substance

R = universal gas constant

T = temperature

Rearranging this equation, we get:n/V = P/RT

We can use the above formula to calculate the number of moles of CO gas in the room:

n/V = P/RT

n/V = (1 atm) / (0.0821 L·atm/mol·K * 298 K)

n/V = 0.040 mol/Lor

n = (0.040 mol/L) x (1 L/1000 mL) x (1000000 µg/1 g) = 40 µg/mL

Now, we can convert µg/mL to µg/m³ using the following formula:

µg/m³ = µg/mL x (1 / density of CO gas at 25 °C)

Density of CO gas at 25 °C = 1.250 g/L (source)

µg/m³ = 40 µg/mL x (1 / 1.250 g/L) x (1000 mL/1 L) = 32,000 µg/m³

b. The high concentration of carbon monoxide in a smoke-filled room can cause various symptoms to people who are sensitive to it.

The symptoms of carbon monoxide poisoning include headache, dizziness, nausea, vomiting, weakness, chest pain, and confusion. High levels of carbon monoxide can lead to loss of consciousness, brain damage, and death.

Therefore, it is important to ensure proper ventilation and avoid exposure to smoke-filled rooms containing high levels of carbon monoxide.

Know more about concentration here:

https://brainly.com/question/30546057

#SPJ11

Based on the octet rule, the predicted number of bonds in molecule A would be four for carbon, three for phosphorus, two for sulfur, and one for chlorine (option A).

According to the octet rule, atoms tend to form bonds in order to achieve a stable electron configuration with eight valence electrons. Based on this rule, we can predict the number of bonds carbon ©, phosphorus (P), sulfur (S), and chlorine (Cl) are likely to form in a molecule.

The options provided are as follows:

A. Four bonds for carbon, three bonds for phosphorus, two bonds for sulfur, and one bond for chlorine.

B. Four bonds for carbon, four bonds for phosphorus, three bonds for sulfur, and three bonds for chlorine.

C. Four bonds for carbon, one bond for phosphorus, one bond for sulfur, and one bond for chlorine.

D. Three bonds for carbon, three bonds for phosphorus, two bonds for sulfur, and two bonds for chlorine.

Applying the octet rule, we determine that carbon typically forms four bonds, phosphorus forms three bonds, sulfur forms two bonds, and chlorine forms one bond. Comparing these predictions with the given options, we find that option A matches the predicted number of bonds: Four, three, two, one, respectively.

Learn more about Octet rule here: brainly.com/question/30779148

#SPJ11

The mass of acetylene, propane, and butane in the mixture are 0.018 g, 1.57 g, and 0.45 g respectively.

We are given a mixture of three gases which can be considered as an ideal gas mixture. The partial pressure of acetylene is given to be 15 kPa. Therefore the partial pressure of propane and butane would be the remaining pressure i.e (100 - 15 - 65 = 20 kPa)

Step 1: Calculate the mole fraction of each component

Mole fraction of acetylene  =  15 kPa / 100 kPa = 0.15

Mole fraction of propane  =  65 kPa / 100 kPa = 0.65

Mole fraction of butane  =  20 kPa / 100 kPa = 0.20

Total mole fraction,  x_total = 0.15 + 0.65 + 0.20 = 1

Step 2: Calculate the number of moles of each component

The total number of moles of the mixture  =  n_total = P.V / R.T

Let's consider 1 mole of the mixture.

Pressure of the mixture  =  100 kPa

Temperature of the mixture  =  20 °C

Volume occupied by 1 mole of the mixture  =  V = 0.100 m³

Gas constant  =  R = 8.31 J/K-mol

Total number of moles  =  n_total  = (100 kPa x 0.100 m³) / (8.31 J/K-mol x (273 + 20) K) = 0.04415 mol

Step 3: Calculate the mass of each component

Molar mass of C2H2  =  2 x 12.01 g/mol + 2 x 1.008 g/mol = 26.04 g/mol

Molar mass of C3H8  =  3 x 12.01 g/mol + 8 x 1.008 g/mol = 44.1 g/mol

Molar mass of C4H10  =  4 x 12.01 g/mol + 10 x 1.008 g/mol = 58.12 g/mol

Mass of C2H2  =  mole fraction of C2H2 x total number of moles x molar mass of C2H2

= 0.15 x 0.04415 mol x 26.04 g/mol = 0.018 g

Mass of C3H8  =  mole fraction of C3H8 x total number of moles x molar mass of C3H8

= 0.65 x 0.04415 mol x 44.1 g/mol = 1.57 g

Mass of C4H10  =  mole fraction of C4H10 x total number of moles x molar mass of C4H10

= 0.20 x 0.04415 mol x 58.12 g/mol = 0.45 g

Therefore the mass of acetylene, propane, and butane in the mixture are 0.018 g, 1.57 g, and 0.45 g respectively.

To learn more about partial pressure :

https://brainly.com/question/31196860

#SPJ11

Answer:

Based on the activity series, the most likely reactions are:

Pt + FeCl3 -> FeCl3 + Pt

Li + ZnCO3 -> Li2CO3 + Zn