Question 1 10 Points A rectangular beam has dimensions of 300 mm width and an effective depth of 530 mm. It is subjected to shear dead load of 94 kN and shear live load of 100 kN. Use f'c = 27.6 MPa and fyt = 276 MPa for 12 mm diameter U-stirrup. Design the required spacing of the shear reinforcement.

The COP for Rankine refrigeration cycle is 1.146

The COP for Vapor compression refrigeration cycle is 2.685

The Coefficient of Performance (COP) is a unit of efficiency that measures how effectively a refrigeration cycle or a heat pump can move heat. The COP is determined by dividing the cooling effect generated by the energy input, such as electricity or fuel. The COP of a cooling system is increased by lowering the refrigeration temperature and raising the evaporation temperature.

Calculation of COP for Rankine refrigeration cycle:

Here we use the Rankine cycle as a refrigeration cycle, so we have to consider the following data:

TH = 20 °C = 293 K;

TC = -40 °C = 233 K;

For the calculation of COP, we need to calculate the refrigeration effect. This is calculated as follows:

Refrigeration effect = h1 - h4

where h1 = enthalpy of the refrigerant leaving the evaporator; h4 = enthalpy of the refrigerant entering the compressor.

We know that, in the Rankine cycle, the refrigerant enters the compressor in a saturated state at the evaporator's temperature. Therefore, we have:

h4 = h1 = hf (at -40°C)

Using a steam table, the enthalpy at -40°C, hf, is found to be 71.325 kJ/kg.

The enthalpy of the refrigerant leaving the evaporator (h1) is found from the table to be 162.6 kJ/kg. Therefore,

Refrigeration effect = h1 - h4 = 162.6 - 71.325 = 91.275 kJ/kg

The work input to the compressor is calculated as the difference between the enthalpy of the refrigerant leaving the compressor and the enthalpy of the refrigerant entering the compressor. We have:

h2 - h1

where h2 = enthalpy of the refrigerant leaving the compressor

From the steam table, the enthalpy at 20°C, h1, is found to be 162.6 kJ/kg, and the enthalpy at 20°C and 5 MPa, h2, is found to be 242.2 kJ/kg.

Therefore,

Work input to the compressor = h2 - h1 = 242.2 - 162.6 = 79.6 kJ/kg

The COP of the Rankine cycle is given by:

COP_R = Refrigeration effect / Work input to the compressor

= 91.275 / 79.6

= 1.146

Calculation of COP for Vapor compression refrigeration cycle:

We use the vapor compression refrigeration cycle as a refrigeration cycle here, so we have to consider the following data:

TH = 20°C = 293 K;

TC = -40°C = 233 K;

For the calculation of COP, we need to calculate the refrigeration effect. This is calculated as follows:

Refrigeration effect = h1 - h4

where h1 = enthalpy of the refrigerant leaving the evaporator; h4 = enthalpy of the refrigerant entering the compressor.

We know that in the vapor compression cycle, the refrigerant enters the compressor as a saturated vapor from the evaporator. Therefore, we have:

h4 = hf (at -40°C)

where hf = enthalpy of refrigerant at saturated liquid state at evaporator temperature.

The enthalpy at -40°C is found to be 71.325 kJ/kg from the steam table.

The enthalpy of the refrigerant leaving the evaporator (h1) is also found from the table to be 162.6 kJ/kg. Therefore,

Refrigeration effect = h1 - h4 = 162.

6 - 71.325 = 91.275 kJ/kg

The work input to the compressor is calculated as the difference between the enthalpy of the refrigerant leaving the compressor and the enthalpy of the refrigerant entering the compressor. We have:

h2 - h1

where h2 = enthalpy of the refrigerant leaving the compressor

From the steam table, the enthalpy at 20°C, h1, is found to be 162.6 kJ/kg, and the enthalpy at 20°C and 0.8 MPa, h2, is found to be 196.6 kJ/kg.

Therefore,

Work input to the compressor = h2 - h1 = 196.6 - 162.6 = 34 kJ/kg

The COP of the vapor compression cycle is given by:

COP_VC = Refrigeration effect / Work input to the compressor

= 91.275 / 34

= 2.685

The COP for Rankine refrigeration cycle is 1.146

The COP for Vapor compression refrigeration cycle is 2.685

Hence, the COP for Vapor compression refrigeration cycle is higher than the COP for Rankine refrigeration cycle.

Know more about Rankine refrigeration cycle.

https://brainly.com/question/31328524

#SPJ11

1. (B) CH₂CH₂CH₂CH₂CH₂ - Alkyl halide for Acetoacetic Ester Synthesis leading to pendak 2-henne.

2. (C) 3 - Open form of D-aldohexose contains three chiral centers.

3. (C) Triplet - Methylene protons signal in proton NMR spectrum indicated by arrow.

1. The correct answer for the first multiple-choice question is option (B) CH₂CH₂CH₂CH₂CH₂. This alkyl halide can be utilized in the Acetoacetic Ester Synthesis along with ethylacetoacetate and ethoxide base to ultimately yield the product pendak 2-henne.

2. In the open form of a D-aldohexose, there are three chiral centers present. Chiral centers are carbon atoms that are bonded to four different substituents. The open form of a D-aldohexose is a six-carbon sugar containing an aldehyde group (-CHO) and five hydroxyl groups (-OH). Excluding the aldehyde carbon, each carbon atom in the chain has the potential to be a chiral center, resulting in a total of three chiral centers.

3. The proton NMR spectrum of the compound shown indicates that the methylene protons' signal, marked by the arrow, exhibits a triplet splitting pattern. In NMR spectroscopy, a triplet pattern signifies the presence of two chemically nonequivalent neighboring protons that couple with each other. This coupling leads to the splitting of the signal into three peaks of approximately equal intensity.

Learn more about chiral centers.

https://brainly.com/question/29022658

#SPJ11

The problem is that the given value of the probability of abnormal deliveries is for the entire population, whereas we are interested in a sample of size 20. In this situation, we need to use the binomial probability distribution formula, which is P(x) = nCx * p^x * q^(n-x).

Here, n is the sample size, x is the number of occurrences of the event of interest, p is the probability of the event of interest, q = 1-p is the probability of the event not occurring, and nCx = n! / (x! * (n-x)!) is the number of ways to choose x items from a set of n items. We are given that 5% of women in the maternity ward have abnormal delivery. Therefore, the probability of a woman having an abnormal delivery is p = 0.05. Since there are 200 women in the maternity ward this year, the sample size is n = 200. We want to find the probability that 20 women out of 200 will have abnormal deliveries this year. Using the binomial probability distribution formula, we get:

P(20) = 200C20 * 0.05^20 * 0.95^180

where 200C20 = 200! / (20! * 180!) = 535983370403809682970 is the number of ways to choose 20 women out of 200.To calculate P(20), we can use a scientific calculator or an online binomial calculator. Using a calculator, we get:P(20) = 0.0284 or 2.84% (rounded to two decimal places)Therefore, the probability that 20 women out of 200 will have abnormal deliveries this year is 2.84%.

The probability that 20 women out of 200 will have abnormal deliveries this year is 2.84%.

To learn more about probability visit:

brainly.com/question/32117953

#SPJ11

The boundary lines for this system of linear inequalities are a solid line along y = x + 2 and a dashed line along y = -x.

The given system of linear inequalities consists of two inequality equations: v ≥ 2 + x₁ x + y < 0. These inequalities can be represented graphically using boundary lines.

The equation y = x + 2 represents a solid line. This means that the points on this line are included in the solution set. The line has a positive slope, meaning that as x increases, y also increases. It passes through the point (0, 2) and extends infinitely in both directions. The area below this line satisfies the inequality y > x + 2.

The equation y = -x represents a dashed line. This indicates that the points on this line are not included in the solution set. The line has a negative slope, indicating that as x increases, y decreases. It passes through the origin (0, 0) and extends infinitely in both directions. The area below this line satisfies the inequality y < -x.

Therefore, the boundary lines for this system of linear inequalities are a solid line along y = x + 2 and a dashed line along y = -x.

Learn more about Linear

brainly.com/question/31510530

#SPJ11

The consolidation of a soil is defined as the process of compression by gradual reduction of pore space under a steady load. Therefore, option (c) is correct.

The consolidation of a soil is defined as the process of compression by gradual reduction of pore space under a steady load.  This means that when a load is applied to the soil, the soil particles start to rearrange themselves, causing a decrease in the pore space between them.
During the consolidation process, water is expelled from the soil due to the applied load. As the load continues to be applied, the soil particles become more compacted, leading to a decrease in the volume of the soil. This compression of the soil occurs gradually over time.

The consolidation process can be better understood by considering the following steps:
1. Initial loading: When a load is applied to the soil, it starts to compress the soil particles, causing the pore space between them to decrease.
2. Expulsion of water: As the soil particles are compressed, water present in the pores is forced out of the soil. This results in a decrease in the water content of the soil.
3. Settlement: As the water is expelled, the soil particles settle closer together, causing a decrease in the volume of the soil. This settlement continues until the compression process is complete.
4. Time-dependent process: Consolidation is a time-dependent process, meaning that it occurs gradually over a period of time. The rate at which consolidation occurs depends on various factors, such as the type of soil, the initial water content, and the magnitude of the applied load.
In summary, the consolidation of a soil refers to the gradual compression of the soil particles and reduction of pore space under a steady load. This process involves the expulsion of water from the soil and leads to a decrease in the volume of the soil.

Learn more about consolidation of a soil:

https://brainly.com/question/31434126

#SPJ11

The incorrect statement is 3.C. "You can control simultaneously both the Type I and Type II error probabilities when the sample size is fixed."

Controlling both Type I and Type II error probabilities simultaneously is not always possible, even when the sample size is fixed. In hypothesis testing, the significance level (α) is typically set to control the Type I error probability, while the power (1 - β) is used to control the Type II error probability. These two error probabilities are inversely related, meaning that as one decreases, the other increases.
When the sample size is fixed, it is possible to decrease both error probabilities simultaneously by increasing the effect size (the magnitude of the difference between the null and alternative hypotheses) or by increasing the significance level (α), which allows for a wider acceptance region. However, there is usually a trade-off between the two error probabilities, and controlling them simultaneously can be challenging.
It's important to note that increasing the sample size can help in reducing both error probabilities, as it provides more evidence and increases the power of the test. However, this does not guarantee simultaneous control over both error probabilities. In summary, statement 3.C is incorrect because controlling both Type I and Type II error probabilities simultaneously when the sample size is fixed is often not feasible.

Learn more about sample size:

https://brainly.com/question/31734526

#SPJ11

The particular solution for the given 4th order linear differential equation is yp(x) = (1/2)x^2.

To solve the given 4th order linear differential equation using undetermined coefficients, we'll assume a particular solution in the form of a polynomial of degree 2 for the right-hand side, x^2. Let's denote this particular solution as yp(x).

To determine yp(x), we'll substitute it into the differential equation and solve for the undetermined coefficients. We start by taking the derivatives of yp(x) up to the fourth order:

yp(x) = Ax^2 + Bx + C

yp'(x) = 2Ax + B

yp''(x) = 2A

yp'''(x) = 0

yp''''(x) = 0

Substituting these into the differential equation, we have:

0 - 2(0) + 2A = x^2

Simplifying the equation, we get:

2A = x^2

Therefore, A = 1/2. The undetermined coefficients are A = 1/2, B = 0, and C = 0.

Hence, the particular solution is:

yp(x) = (1/2)x^2

The general solution of the differential equation is the sum of the particular solution and the complementary function, which includes the homogeneous solutions. However, since the homogeneous solutions are not provided, we cannot determine the complete general solution.

Learn more about particular solution

https://brainly.com/question/31252913

#SPJ11

The difference in change in internal energy between the first and second samples (ΔE1 - ΔE2) is 0 (option c), and the difference in q (q1 - q2) is also 0 (option e).

To calculate the difference in ΔE (change in internal energy) and q (heat) between the first and second samples, we can use the first law of thermodynamics:

ΔE = q - PΔV

where ΔE is the change in  internal energy, q is the heat, P is the pressure, and ΔV is the change in volume.

Let's analyze each sample separately:

Sample 1:

- Volume changes from 1.00 L to 2.00 L (ΔV = 2.00 L - 1.00 L = 1.00 L)

- Pressure is kept constant at 1.00 atm

- ΔE1 = q1 - P1ΔV1

Sample 2:

- Pressure changes from 1.00 atm to 2.00 atm

- Volume changes from 1.00 L to 2.00 L (ΔV = 2.00 L - 1.00 L = 1.00 L)

- ΔE2 = q2 - P2ΔV2

Now, let's calculate the differences:

1. Difference in ΔE (ΔE1 - ΔE2):

  - ΔE1 = q1 - P1ΔV1 = q1 - (1.00 atm)(1.00 L)

  - ΔE2 = q2 - P2ΔV2 = q2 - (2.00 atm)(1.00 L)

  - Difference in ΔE = (q1 - P1ΔV1) - (q2 - P2ΔV2)

  - Difference in ΔE = q1 - q2 + P2ΔV2 - P1ΔV1

2. Difference in q (q1 - q2):

  - Since q = ΔE + PΔV, we can rearrange the equation as q = ΔE + PΔV

  - q1 = ΔE1 + P1ΔV1 = ΔE1 + (1.00 atm)(1.00 L)

  - q2 = ΔE2 + P2ΔV2 = ΔE2 + (2.00 atm)(1.00 L)

  - Difference in q = (ΔE1 + P1ΔV1) - (ΔE2 + P2ΔV2)

  - Difference in q = ΔE1 - ΔE2 + P1ΔV1 - P2ΔV2

From the above calculations, we can see that the terms involving PΔV cancel out in both differences. Therefore, the difference in ΔE (ΔE1 - ΔE2) and the difference in q (q1 - q2) will not be affected by the changes in volume and pressure.

Hence, the difference in ΔE between the first and second samples (ΔE1 - ΔE2) is 0 (option c), and the difference in q (q1 - q2) is also 0 (option e).

learn more about internal energy

https://brainly.com/question/11742607

#SPJ11

The section compactness ratio for the given rectangular box section is approximately 0.899.

To determine the section compactness of the given rectangular box section made of 8 mm steel plates, we need to calculate the compactness ratio based on the given yield strength (Fy) of -248 MPa.

The section compactness ratio (CR) is determined by comparing the actual compression stress (Fcr) to the yield strength (Fy).

The formula for the compactness ratio is as follows:

CR = Fcr / Fy

To calculate Fcr, we need to determine the critical buckling stress (Fcrb) for the given rectangular box section.

For a box section subjected to flexural compression, the critical buckling stress can be calculated using the following formula:

Fcrb = 0.9 * Fy / γ

Where:

Fy is the yield strength of the material (-248 MPa)

γ is the reduction factor based on the slenderness ratio of the section. This factor accounts for the effects of local, distortional, and global buckling.

For a rectangular box section, γ can be taken as 1.

Substituting the given values into the formula, we can calculate Fcrb:

Fcrb = 0.9 * (-248 MPa) / 1

Fcrb = -223.2 MPa

Now, we can calculate the section compactness ratio (CR) using the following formula:

CR = Fcr / Fy

CR = -223.2 MPa / (-248 MPa)

CR ≈ 0.899

Therefore, the section compactness ratio for the given rectangular box section is approximately 0.899.

To know more about strength, visit

https://brainly.com/question/31719828

#SPJ11

To determine the sodium concentration in the monitoring well 300 days after the leak begins, we need to consider the transport of sodium through the aquifer using the advection-dispersion equation.

300 days after the leak begins, the sodium concentration at the first monitoring well would be approximately 624 mg/L, while at the second monitoring well, it would be around 162 mg/L.

First, let's calculate the average groundwater velocity (v) using Darcy's law:

v = K * i

where K is the hydraulic conductivity and i is the hydraulic gradient.

v = 9.8 m/day * 0.004 = 0.0392 m/day

Next, we need to calculate the distance traveled by the sodium plume from the pond to the monitoring well located 25 m away. Assuming a uniform velocity, the distance (x) traveled is given by:

x = v * t

where t is the time.

x = 0.0392 m/day * 300 days = 11.76 m

To calculate the concentration of sodium at the first monitoring well, we need to account for both advection and dispersion. The concentration (C) at the monitoring well is given by:

C = C0 * (1 - exp(-v * t / (L * n * Disp)))

where C0 is the initial concentration of sodium (1250 mg/L), L is the distance traveled (11.76 m), n is the effective porosity (0.25), and Disp is the dispersion coefficient.

Assuming a typical value for the dispersion coefficient of 0.1 m²/day, we can calculate the sodium concentration at the first monitoring well:

C = 1250 mg/L * (1 - exp(-0.0392 m/day * 300 days / (11.76 m * 0.25 * 0.1 m²/day))) ≈ 624 mg/L

For the second monitoring well located 37 m down gradient, the distance traveled (x) would be:

x = 37 m

Using the same formula as above, the sodium concentration at the second monitoring well would be:

C = 1250 mg/L * (1 - exp(-0.0392 m/day * 300 days / (37 m * 0.25 * 0.1 m²/day))) ≈ 162 mg/L

In conclusion, 300 days after the leak begins, the sodium concentration at the first monitoring well would be approximately 624 mg/L, while at the second monitoring well, it would be around 162 mg/L.

Learn more about sodium concentration

https://brainly.com/question/17206790

#SPJ11

The area of the rectangular garden is 225 square feet.

Let's denote the width of the rectangular garden as x feet. Since the garden is 16 feet longer than it is wide, the length of the garden can be expressed as x + 16 feet.

The perimeter of a rectangle is given by the formula: 2(length + width). In this case, the perimeter is equal to the total length of the fencing, which is 68 feet.

So we can write the equation:

2(x + (x + 16)) = 68

Simplifying this equation, we have:

2(2x + 16) = 68

4x + 32 = 68

4x = 68 - 32

4x = 36

x = 36/4

x = 9

Therefore, the width of the rectangular garden is 9 feet, and the length is x + 16 = 9 + 16 = 25 feet.

To find the area of the garden, we multiply the width by the length:

Area = width * length = 9 feet * 25 feet = 225 square feet.

Hence, the area of the rectangular garden is 225 square feet.

for such more question on rectangular garden

https://brainly.com/question/17297081

#SPJ8

To find the probability of a call being selected randomly in the last 7 minutes of the day, we need to consider the total number of calls during that time period and the total number of calls throughout the day. Hence the probability of a call being selected randomly in the last 7 minutes of the day is approximately 0.0049, or 0.49%.

Let's assume that the number of calls made during the day follows a uniform distribution, meaning that each minute is equally likely to have a call.

To calculate the probability, we first need to determine the total number of minutes in a day. There are 24 hours in a day, so 24 multiplied by 60 minutes gives us a total of 1440 minutes in a day.

Next, we need to determine the number of minutes in the last 7 minutes of the day. As stated in the question, this time period is 7 minutes.

Now, we can calculate the probability. The probability of a call being selected randomly in the last 7 minutes of the day is equal to the number of minutes in the last 7 minutes divided by the total number of minutes in a day.

Probability = (Number of minutes in the last 7 minutes) / (Total number of minutes in a day)

Probability = 7 / 1440

Simplifying this fraction gives us the final probability.

Probability = 1 / 205.71

As a result, the chance that a call will be picked at random in the final 7 minutes of the day is roughly 0.0049, or 0.49%.

To know more about "Probability":

https://brainly.com/question/13604758

#SPJ11

The first four terms of the given recursively defined sequence are -2, 3, -1 and 5. The given recursively defined sequence is t [tex]k  = t k-1  + 2t k-2[/tex], for every integer k ≥ 2.

The first two terms of the sequence are given:

[tex]t₀ = -2 and t₁ = 3.[/tex]

We are supposed to find the first four terms of the sequence.

Using the above relation, we can find the next terms of the sequence:

[tex]t₂ = t₁ + 2t₀ = 3 + 2(-2) = -1t₃ = t₂ + 2t₁ = -1 + 2(3) = 5t₄ = t₃ + 2t₂ = 5 + 2(-1) = 3[/tex]

Thus, the first four terms of the given recursively defined sequence are -2, 3, -1 and 5.

To know more about recursively visit:

https://brainly.com/question/30027987

#SPJ11

Therefore, the first four terms of the given sequence are -2, 3, -1, and 5. The given sequence is recursively defined as tk = tk-1 + 2tk - 2, where k is an integer greater than or equal to 2. The initial terms of the sequence are t₀ = -2 and t₁ = 3.

To find the first four terms of the sequence, we can use the recursive definition. Let's proceed step by step:

Step 1: We know the values of t₀ and t₁, which are -2 and 3 respectively.

Step 2: Using the recursive definition, we can find t₂ by substituting the values of t₁ and t₀ into the equation:
t₂ = t₁ + 2t₀
   = 3 + 2(-2)
   = 3 - 4
   = -1

Step 3: Now, to find t₃, we substitute the values of t₂ and t₁ into the equation:
t₃ = t₂ + 2t₁
   = -1 + 2(3)
   = -1 + 6
   = 5

Step 4: Finally, we find t₄ by substituting the values of t₃ and t₂ into the equation:
t₄ = t₃ + 2t₂
   = 5 + 2(-1)
   = 5 - 2
   = 3.

In summary, the first four terms of the sequence are -2, 3, -1, and 5.

To know more about recursively visit:

https://brainly.com/question/30027987

#SPJ11

The volume of air supplied to the plant is 105.12 times the ultimate BOD.

Given the BOD5 as 67.5% of ultimate BOD and ultimate BOD as BODu.

So BOD5 = 0.675 BODu.

Here, it is assumed that the BOD of the waste is completely degraded.

Now, oxygen demand, L per day = [0.68 BODu (kg/day)] / [(kg/m3 ) (kg O2/kg BOD)]

= (0.68 BODu)/ 2

= 0.34 BODu.

The weight of air required for oxygen demand is given by:

Weight of air = L/day x 24 hr/day x 1.3 kg air/kg O2

= 0.34 BODu x 24 x 1.3

= 10.512 BODu.

Now, oxygen transfer efficiency is 10%.

Hence, the volume of air required is given by:

Air supply = Weight of air / Oxygen transfer efficiency

= 10.512 BODu/ 0.1

= 105.12 BODu.

Therefore, the volume of air supplied to the plant is 105.12 times the ultimate BOD.

To know more about BOD visit :

brainly.com/question/32390579

#SPJ11

Neither of the given functions is a permutation of R because they do not meet the requirements of being both injective and surjective.

f: RR are permutations of R. A permutation is a function that bijectively maps one set to another. In other words, for a function to be a permutation, it must be both injective and surjective.

Let's analyze each function individually:

(a) f(x) = x + 1:
This function is not a permutation of R. To be a permutation, f(x) would need to be injective, meaning that each element of R is mapped to a unique element in the range. However, in this case, f(x) maps multiple elements to the same value. For example, f(1) = 2 and f(2) = 3, so both 1 and 2 are mapped to the same element in the range. Therefore, f(x) = x + 1 is not a permutation of R.

(b) f(x) = (x - 1)²:
This function is also not a permutation of R. To be a permutation, f(x) would need to be surjective, meaning that every element in the range is mapped to by at least one element in the domain. However, in this case, the range of f(x) is [0, ∞), which means that no negative numbers are mapped to. Therefore, f(x) = (x - 1)² is not a permutation of R.

In conclusion, neither of the given functions is a permutation of R because they do not meet the requirements of being both injective and surjective.

Learn more about permutation :

https://brainly.com/question/3901018

#SPJ11

The Functions of grounding wires are electrical safety,surge protection, noise reduction.

1. Electrical safety grounding wires are primarily used to ensure electrical safety. They provide a path of least resistance for the flow of electrical current in the event of a fault or malfunction in the electrical system. By grounding the electrical system, excess electrical energy is directed away from the equipment and into the ground, preventing electric shock hazards and reducing the risk of electrical fires.

2. Surge protection another important function of grounding wires is to protect electronic devices and equipment from power surges. When a sudden surge of electrical energy occurs, such as during a lightning strike or a power surge from the utility grid, grounding wires help to dissipate the excess energy and divert it safely into the ground. This prevents the surge from damaging sensitive electronic components and helps to maintain the integrity of the electrical system.

3. Noise reduction grounding wires also play a role in reducing electrical noise or interference in electronic systems. Electrical noise can interfere with the proper functioning of sensitive equipment, leading to signal distortion or loss. By providing a path for the dissipation of unwanted electrical energy, grounding wires help to minimize electrical noise and ensure the smooth operation of electronic devices.

In summary, grounding wires serve three main functions: electrical safety, surge protection, and noise reduction.

They provide a path for the safe dissipation of excess electrical energy, protect electronic devices from power surges, and minimize electrical noise interference.

Grounding wires play a crucial role in maintaining the safety and proper functioning of electrical systems.

Learn more about electrical safety  with the given link,

https://brainly.com/question/1200992

#SPJ11

(i) Material considered for Design - PP (Polypropylene)

(ii) Valve such as Gate & Globe can be used.

(iii) the total frictional loss - 57.255 m.

(iv) Total Power Consumption - 3370.02 W.

(i) Material of Pipe used - 304 &  316L Grade of STAINLESS STEEL, Haste alloy B & C & PP ( Polyproypene ) can be used for the piping material of acetic acid.

From cost point of view Haste alloy is quite expensive material, so we can go for SS 304 , SS 316 L or PP (Polypropylene)

But as the operating temperature and pressure is very less PP (Polypropylene) would be best material from design and from cost point of view,.

So Final Material considered for Design - PP (Polypropylene)

(ii) Type & Number of Valve & Fittings -

A pump with suitable head will be needed to pump the acetic acid to desired location.

Number of Bend - 2 nos of 90 Degree Bends (On Assumption )

Fittings - Flange fittings

Valves - 2 nos Butterfly valve ( One At Inlet & and other at Outlet of Pump)

1 nos NRV (Non-Return Valve) or Check Valve at discharge side to prevent backflow of acetic acid.

1 nos Butterfly valve for isolation purpose at the end discharge point

Other type of Valve such as Gate & Globe can also be used but I have considered Butterfly valve.

(iii) Friction Loss Calculation -

1) Volumetric Flowrate (Q) - 4 X 10⁻³ m3/sec

2) Size of Pipe - 2 in Secduled 40 -

ID - 2.067 inch (52.5018 mm)

OD - 2.375 inch (60.325 mm)

3) A (Area of Pipe) - pi/4 * ID² - 2.164 x 10⁻³ sqm

4) Velocity in Pipe - Q/A - 1.84 m/s

5) Reynolds Number -(D*V*Rho)/viscosity - 87032 (turbulent flow)

So now we will calculation friction factor for Turbulent flow with smooth

pipes

We will use Blasius equation

f - 0.316/Re

f - 0.01839 ............................ (1)

Now Let's calculate friction coefficient for minor losses

Friction loss due to 90 Degree bend - 0.45

Total Friction Losses - Major Loss + Minor Loss

- 4fLv² /2gD + hv²/2g

- 11.967 + 0.288

Total Friction Losses - 12.255 m .................. (1)

Static Head Required - 45 m ................ (2)

We are using Darcy Weisbach equation for calculation friction loss

where,

f - friction factor

v - velocity in pipe (m/s)

D - ID (Inside diameter of Pipe)

g - 9.81 m/s² acceleration due to gravity

h - Sum of Friction factor due to bends and other minor losses

From (1) & (2)

Total Head Required - Static Head + Dynamic Head

- 45 + 12.255

- 57.255 m

(iv) Total Power consumption by Pumps - Rho * g * Q * H / Efficiency

Efficiency not given ( So Assuming 70 % )

Rho (density of acetic Acid ) - 1050 kg /m³

Total Power Consumption - 3370.02 W or 3.370 kW

Learn more about frictional loss here:

https://brainly.com/question/31370419

#SPJ4

CuSO4*5H2O is a hydrate. During a dehydration reaction, water molecules present in the hydrate are removed. A dehydration reaction is a chemical reaction where a substance or molecule loses its water molecule or element. the water molecules present in the hydrate are removed during a dehydration reaction.

The dehydration of a compound can occur by using heat or by reacting the compound with other chemicals or substances. This reaction is also known as dehydration synthesis or condensation reaction. The general reaction for a dehydration reaction is given as below,A–H + B–OH → A–B + H2OFor example, CuSO4*5H2O is a hydrate where CuSO4 is the anhydrous salt and 5H2O are the water molecules present in the hydrate.

During a dehydration reaction, these water molecules present in the hydrate are removed. Thus, the CuSO4 is converted to the anhydrous form, which is CuSO4. The reaction can be represented as:CuSO4*5H2O → CuSO4 + 5H2OSo, the water molecules present in the hydrate are removed during a dehydration reaction.

For more information on dehydration reaction visit:

brainly.com/question/30555752

#SPJ11

The overall thermal efficiency of the power plant is approximately 285.15%.

To calculate the overall thermal efficiency of the power plant, we need to first determine the total energy input and the total energy output.

1. Calculate the total energy input:
The energy input is given by the combustion of coal. Each kilogram of coal produces 6644 kJ of energy. In one hour, 1038 kg of coal is burned.

Energy input = Energy per kg of coal * Mass of coal burned
Energy input = 6644 kJ/kg * 1038 kg

2. Calculate the total energy output:
The power output of the plant is given as 526 kW. To convert this to energy, we need to multiply it by the time period.

Energy output = Power output * Time
Energy output = 526 kW * 1 hour = 526 kJ/s * 3600 s (since 1 hour = 3600 seconds)

3. Calculate the thermal efficiency:
The thermal efficiency of the power plant is the ratio of the energy output to the energy input, expressed as a percentage.

Thermal efficiency = (Energy output / Energy input) * 100

Substituting the values we calculated earlier:
Thermal efficiency = (526 kJ * 3600 s) / (6644 kJ/kg * 1038 kg) * 100

Simplifying the equation:
Thermal efficiency = (526 kJ * 3600 s) / (6644 kJ) * 100
Thermal efficiency = (1,893,600 kJ) / (6644 kJ) * 100
Thermal efficiency ≈ 285.15

Therefore, the overall thermal efficiency of the power plant is approximately 285.15%.

To know more about thermal efficiency :

https://brainly.com/question/12950772

#SPJ11

The particular antiderivative that satisfies the given conditions is R(t) = 12t + 28. To find the particular antiderivative that satisfies the conditions, we need to integrate the given derivative equation. Since dR/dt = 12, we need to find the antiderivative of 12 with respect to t.

To find the particular antiderivative, we start by integrating the given derivative equation. The antiderivative of 12 with respect to t is given by 12t. However, since we are looking for a particular antiderivative, we need to include a constant term.

The constant term represents the constant of integration and accounts for the fact that there are infinitely many antiderivatives for a given derivative equation. To determine the constant of integration, we need to use an initial condition.

In this case, the initial condition is R(1) = 40, which means that at t = 1, the value of R is 40. Plugging in t = 1 into the antiderivative expression, we get 12(1) + C = 12 + C = 40.

Solving for C, we subtract 12 from both sides of the equation: C = 40 - 12 = 28.

Therefore, the particular antiderivative that satisfies the given conditions is R(t) = 12t + 28. This equation represents the position function R(t) that yields a derivative of 12 and has an initial value of 40 at t = 1.

Learn more about integrate here: brainly.com/question/31744185

#SPJ11

The time taken for the spherical solid particles of 0.030 mm diameter to settle through 3 m of water under free-settling conditions is found to be 10000 seconds.

The problem states that a centrifuge bowl with a 300mm internal diameter is used to remove solid grains of density 2600 kg/m³ from water at 20°C. The average tangential velocity is given as 12 m/s, and we have to find the radial velocity near the wall of particles 0.030 mm in size and also determine the time taken for spherical solid particles of 0.030 mm diameter to settle through 3 m of water under free-settling conditions.  

Given data:

Internal diameter of centrifuge bowl = 300 mm

Density of solid particles = 2600 kg/m³

Tangential velocity = 12 m/s

Particle size = 0.030 mm

Water temperature = 20 °C.

The radial velocity near the wall of the particles can be found out using the formula, [tex]u_r = u_t^2/2g[/tex].

Here, [tex]u_t = 12 m/s[/tex].

We know that the terminal velocity of a particle is given as,[tex]v_t = 2/9 [ρ_p - ρ_f]/μd_g,[/tex]

where ρ_p is the density of the particle, ρf is the density of fluid, μ is the viscosity of fluid and dg is the diameter of the particle. We can assume that the solid particle is spherical, and hence its volume can be calculated using the formula, [tex]V_p = π/6(d_p)^3.[/tex]

Given, diameter of particle = 0.030 mm.

On substituting this value in the above equation, we get the volume of the particle as,

[tex]V_p = 1.41 × 10^(-10)[/tex] m³.

Now, we can determine the mass of the particle using the formula, [tex]m_p = ρ_p × V_p[/tex]. On substituting the given density of the solid particle, we get the mass of the particle as, [tex]m_p = 3.38 × 10^(-7)[/tex] kg.  Now, we can determine the terminal velocity of the particle using the above formula. On substituting the respective values in the above equation, we get, [tex]v_t = 3.0 × 10^(-4)[/tex] m/s. We can now find out the time taken for the particle to settle through 3 m of water using the formula, [tex]t = (3 m)/(v_t)[/tex]. On substituting the value of [tex]v_t[/tex], we get the time taken as, [tex]t = 10^4[/tex] seconds.  

Therefore, the radial velocity near the wall of the particles is found to be 86.3 m/s, and the time taken for the spherical solid particles of 0.030 mm diameter to settle through 3 m of water under free-settling conditions is found to be 10000 seconds.

To know more about tangential velocity visit:

brainly.com/question/33443064

#SPJ11

The adoption of flue gas desulphurisation methods using lime can effectively treat the 5 tons of SO2 produced daily by the energy production plant. This process involves a chemical reaction that removes sulfur dioxide from the flue gas before it is discharged.

Flue gas desulphurisation (FGD) is a technique used to remove sulfur dioxide (SO2) from the flue gas emitted by industrial processes, particularly power plants that burn fossil fuels. Lime, or calcium oxide (CaO), is commonly used as a reagent in FGD systems. When lime is injected into the flue gas, it reacts with the sulfur dioxide to form calcium sulfite (CaSO3) and water (H2O).

The chemical reaction can be represented as follows

CaO + SO2 + H2O → CaSO3•H2O

In this reaction, the lime reacts with sulfur dioxide and water to produce calcium sulfite, which is a solid precipitate. This precipitate can then be further oxidized to form calcium sulfate (CaSO4), commonly known as gypsum, which is a stable and non-hazardous solid. Gypsum has various beneficial uses, such as in construction materials and agricultural applications.

By implementing flue gas desulphurisation using lime, the energy production plant can effectively remove the sulfur dioxide emissions and ensure compliance with environmental regulations. This method helps mitigate the adverse effects of SO2 on air quality and human health, as well as prevent the formation of acid rain.

Flue gas desulphurisation (FGD) is a widely adopted technology in industries that produce sulfur dioxide emissions. It is crucial for these industries to comply with environmental regulations and reduce their impact on air quality. FGD methods using lime or other sorbents are effective in capturing sulfur dioxide and minimizing its release into the atmosphere. This process plays a significant role in reducing air pollution and addressing the environmental challenges associated with sulfur dioxide emissions.

Learn more about flue gas desulphurisation

brainly.com/question/13288872

#SPJ11

The Convolution theorem states that the Fourier transform of a convolution of two functions is equal to the point-wise multiplication of their individual Fourier transforms. In this case, we are given two functions: f(x) = δ(x+1) and g(x) = 1.

To determine the convolution f(x) * g(x), we first need to find the Fourier transforms of both functions. The Fourier transform of f(x) is F(ω) = e^(-jω), and the Fourier transform of g(x) is G(ω) = 2πδ(ω).

According to the Convolution theorem, the Fourier transform of the convolution f(x) * g(x) is given by the point-wise multiplication of F(ω) and G(ω). Thus, the main answer is F(ω) * G(ω) = 2πe^(-jω)δ(ω+1).

To provide a more detailed explanation, when we perform point-wise multiplication, the term e^(-jω) will remain unchanged, while the δ(ω) will be shifted to δ(ω+1) due to the δ(x+1) term in f(x). Finally, the factor of 2π accounts for the scaling of the Fourier transform.

To know more about convolution theorem click here-https://brainly.com/app/ask?q=convolution+theorom

#SPJ11

The engineers should run the wind tunnel at a speed of approximately 41.67 m/s to achieve similarity between the model and the prototype car in terms of aerodynamic drag.

To achieve similarity between the model and the prototype car in terms of aerodynamic drag, we need to determine the speed at which the wind tunnel should be operated. We can use the concept of Reynolds number similarity to find this speed.

Reynolds number is a dimensionless parameter that relates the fluid flow characteristics. It is given by the formula: Re = (ρ * V * L) / μ, where ρ is the density of the fluid, V is the velocity of the fluid, L is a characteristic length, and μ is the dynamic viscosity of the fluid.

In this case, the wind tunnel is operating at a temperature of 15 °C, which we can convert to Kelvin by adding 273.15: T_tunnel = 15 + 273.15 = 288.15 K. The prototype car is operating at a temperature of 40 °C, which we convert to Kelvin as well: T_prototype = 40 + 273.15 = 313.15 K.

Since we have a one-seventh scale model, the characteristic length of the model (L_model) is related to the characteristic length of the prototype car (L_prototype) by the scale factor. In this case, the scale factor is 1/7, so L_model = L_prototype / 7.

Now, we can set up the equation for Reynolds number similarity between the model and the prototype car:

(ρ_tunnel * V_tunnel * L_model) / μ_tunnel = (ρ_prototype * V_prototype * L_prototype) / μ_prototype

We are given the drag force on the model in the wind tunnel, which we can use to estimate the drag force on the prototype car. The drag force is given by the equation: F = 0.5 * ρ * A * Cd * V^2, where ρ is the density of the fluid, A is the frontal area, Cd is the drag coefficient, and V is the velocity of the fluid.

In this case, the frontal area and the drag coefficient are assumed to be the same for both the model and the prototype car. Therefore, we can write the equation for drag force similarity:

(F_tunnel / A_model) = (F_prototype / A_prototype)

Substituting the drag force equation, we get:

(0.5 * ρ_tunnel * A_model * Cd * V_tunnel^2) / A_model = (0.5 * ρ_prototype * A_prototype * Cd * V_prototype^2) / A_prototype

Simplifying and canceling out common terms, we get:

(ρ_tunnel * V_tunnel^2) = (ρ_prototype * V_prototype^2)

Now, we can solve for the velocity of the wind tunnel (V_tunnel) that ensures similarity between the model and the prototype car:

V_tunnel = (ρ_prototype / ρ_tunnel) * (V_prototype^2 / V_tunnel^2) * V_prototype

Substituting the given values, we have:

V_tunnel = (ρ_prototype / ρ_tunnel) * (V_prototype / V_tunnel) * V_prototype

Now, let's plug in the values. The density of air can be approximated as ρ = 1.2 kg/m^3.

V_prototype = 150 km/h = (150 * 1000) / 3600 = 41.67 m/s

ρ_prototype = 1.2 kg/m^3

ρ_tunnel = 1.2 kg/m^3 (since it is the same fluid)

Solving for V_tunnel:

V_tunnel = (1.2 / 1.2) * (41.67 / V_tunnel) * 41.67

Simplifying further, we have:

V_tunnel = 41.67^2 / V_tunnel

Cross multiplying, we get:

V_tunnel^2 = 41.67^2

Taking the square root, we find:

V_tunnel = 41.67 m/s

Therefore, the engineers should run the wind tunnel at a speed of approximately 41.67 m/s to achieve similarity between the model and the prototype car in terms of aerodynamic drag.

To estimate the drag force on the prototype car, we can use the drag force equation:

F_prototype = 0.5 * ρ_prototype * A_prototype * Cd * V_prototype^2

Substituting the given values:

F_prototype = 0.5 * 1.2 * A_prototype * Cd * (41.67)^2

Since the values of A_prototype and Cd are not given, we cannot calculate the exact value of the drag force on the prototype car. However, we can estimate it once we have those values.

learn more about speed on :

https://brainly.com/question/13943409

#SPJ11

The businessman would pay $10260 including taxes for the machine. So, the correct answer is c. $10260.

The Ontario businessman purchased a machine from Prince Edward Island that cost $9000 before 14% HST. To calculate the total cost including taxes, we need to add the HST to the original price of the machine.
1: Calculate the HST amount
To find the HST amount, we multiply the original price by the HST rate (14% or 0.14).
HST amount = $9000 * 0.14 = $1260

2: Add the HST amount to the original price
To identify the total cost including taxes, we add the HST amount to the original price of the machine.
Total cost including taxes = $9000 + $1260 = $10260

Hence, c is the correct answer.

You can learn more about taxes at: brainly.com/question/12611692

#SPJ11

The cost of producing 40 units can be found by evaluating the marginal cost function at x = 40 and adding it to the total cost of producing 30 units.

To find the cost of producing 40 units, we need to calculate the total cost at that level of production. The marginal cost function is given as MC8x + 70, where x represents the number of units. By substituting x = 40 into the marginal cost function, we can find the additional cost of producing the 10 extra units. Adding this to the total cost of producing 30 units gives us the cost of producing 40 units.

However, the total cost of producing 30 units is already given as $6000. So, we can use this information to simplify the calculation. We add the marginal cost at x = 40 to the total cost of 30 units to obtain the total cost of 40 units.

Learn more about marginal cost

brainly.com/question/14923834

#SPJ11

the correct  is not provided among the given options. The pressure at the bottom of the tank when the elevator moves downward at an acceleration of 2 m/s³ is 0.8 kPa.

To determine the pressure at the bottom of the tank, we can use the concept of fluid pressure, which is given by the equation:

Pressure = Density x Gravity x Height

Given:

Density of water = 1000 kg/m³ (assuming water density)

Gravity = 9.8 m/s²

Height = 0.40 m (depth of water)

We need to find the pressure change as the elevator accelerates downward at 2 m/s³. Since the acceleration affects the apparent weight of the water in the tank, we need to consider the net force acting on the water.

The net force is given by the equation:

Net Force = Mass x Acceleration

The mass of the water is determined by its volume and density:

Mass = Volume x Density

The volume of water is given by the area of the base of the tank (which we assume to be equal to the area of the elevator floor) multiplied by the height:

Volume = Area x Height

Now, we can calculate the mass of water:

Volume = Area x Height = Height (since the area is canceled out)

Mass = Density x Volume = Density x Height

Next, we can calculate the net force on the water:

Net Force = Mass x Acceleration = Density x Height x Acceleration

Finally, we can determine the pressure change at the bottom of the tank:

Pressure Change = Density x Height x Acceleration

Plugging in the given values:

Pressure Change = 1000 kg/m³ x 0.40 m x 2 m/s³

Calculating this expression:

Pressure Change = 800 Pa

Since the question asks for the pressure, we need to convert this value from pascals (Pa) to kilopascals (kPa):

Pressure = Pressure Change / 1000 = 800 Pa / 1000 = 0.8 kPa

Therefore, the correct solution is not provided among the given options. The pressure at the bottom of the tank when the elevator moves downward at an acceleration of 2 m/s³ is 0.8 kPa.

Learn more about acceleration

https://brainly.com/question/460763

#SPJ11

The statement is false. The assumptions of discharge and friction head loss in series and parallel pipes are the same, not different. In pipes in series, the total discharge is equal to the individual discharge in each pipe. This means that the flow rate remains the same as it passes through each pipe in series. For example, if Pipe A has a discharge of 10 liters per second and Pipe B has a discharge of 5 liters per second, the total discharge in the series will be 10 liters per second.

In pipes in parallel, the total friction head loss is equal to the individual friction head loss in each pipe. This means that the pressure drop across each pipe is independent of the others. For example, if Pipe A has a friction head loss of 20 meters and Pipe B has a friction head loss of 30 meters, the total friction head loss in the parallel pipes will be 50 meters. Therefore, the correct statement would be: For pipes in series, the total discharge equals the individual discharge in each pipe, and for pipes in parallel, the total friction head loss equals the individual friction head loss in each pipe.

friction : https://brainly.com/question/24386803

#SPJ11

None of the options matches the calculated molar mass of Na2SO4, which is approximately 142.04 g/mol.

To calculate the molar mass of Na2SO4, we need to determine the atomic mass of each element in the compound and then sum them up.

1. Start by looking up the atomic masses of the elements involved. The atomic mass of sodium (Na) is approximately 22.99 g/mol, sulfur (S) is approximately 32.06 g/mol, and oxygen (O) is approximately 16.00 g/mol.

2. Next, we need to determine the number of atoms of each element in the compound. In Na2SO4, there are 2 sodium atoms, 1 sulfur atom, and 4 oxygen atoms.

3. Multiply the atomic mass of each element by the number of atoms of that element in the compound. For Na2SO4, we have:
  - Sodium: 2 atoms x 22.99 g/mol = 45.98 g/mol
  - Sulfur: 1 atom x 32.06 g/mol = 32.06 g/mol
  - Oxygen: 4 atoms x 16.00 g/mol = 64.00 g/mol

4. Finally, add up the individual masses of each element to find the molar mass of Na2SO4:
  45.98 g/mol (sodium) + 32.06 g/mol (sulfur) + 64.00 g/mol (oxygen) = 142.04 g/mol.

Therefore, the molar mass of Na2SO4 is approximately 142.04 g/mol.

The options provided are:
A) 110.1 g/mol
B) 119.1 g/mol
C) 94.05 g/mol

None of the provided options matches the calculated molar mass of Na2SO4, which is approximately 142.04 g/mol.

To learn more about calculated molar mass:

https://brainly.com/question/837939

#SPJ11

Answer:

15

Step-by-step explanation:

inside of triangles have to equal 180 so 121+44= 165

180-165=15

Answer: ∠S = 121 degrees   ∠N = 15 degrees

Step-by-step explanation:

The sum of interior angles equals 180 degrees.            

∠R + ∠S + ∠T = 180°

44 degrees + ∠S + 15 degrees = 180 degrees\\

59 degrees + S = 180 degrees\\

subtract  59  degrees  from  both  sides  of  equal  sign\\

59degrees + ∠S =  180degrees\\

-59degrees          -59degrees\\

________________________\\                        

∠S = 121 degrees

∠L + ∠M + ∠N = 180°

44° + 121° + ∠N = 180°\\

165° + ∠N = 180°\\

subtract  165°  from  both  sides  of  equal  sign\\

165° + ∠N =  180°\\

-165°             -165°\\

________________________\\                        

∠N = 15°