Prim coat is a layer of emulsified asphalt applied over a granular base. This layer is applied to bond the base and provide a stable surface for construction.
Tack coat, on the other hand, is a thin layer of asphalt emulsion or asphalt binder applied between two pavement lifts. It serves as an adhesive to promote bonding between the layers.
The tack coat should cover approximately 70 to 100 percent of the lift surface, ensuring sufficient coverage for effective bonding. The exact percentage may vary based on the specific project requirements and environmental conditions.
In conclusion, the prim coat is a layer of asphalt applied over a granular base to bond and stabilize the construction surface, while the tack coat is a thin layer applied between pavement lifts to enhance bonding. The tack coat's coverage should be around 70 to 100 percent of the lift surface. These layers play crucial roles in the construction process, ensuring the durability and longevity of the pavement structure by promoting proper bonding between layers.
To know more about asphalt, visit;
https://brainly.com/question/31491415
#SPJ11
Write each vector as a linear combination of the vectors in 5. (Use 51 and 52, respectively, for the vectors in the set. If not possible, enter IMPOSSIBLE.)
S-((1,2,-2), (2, -1, 1))
(a) z-(-5,-5, 5) (b) v-(-1, -6, 6) (c) w (0,-15, 15) (d) u (1,-5,-5)
a. z = (3,-3, 1) b. v = (1,-3, 3) c. w = (-9,-3, 3) d. u = (1,-3, 3)
Given the set S = {(1,2,-2), (2, -1, 1)} and the following vectors, a linear combination of the vectors in S can be calculated to write each vector as a linear combination of the vectors in S.z = (-5,-5, 5), v = (-1, -6, 6), w = (0,-15, 15), u = (1,-5,-5)
(a) To express z as a linear combination of the vectors in S, z = c1 (1,2,-2) + c2 (2, -1, 1)
We need to solve the system of equations below to find c1 and c2.1.c1 + 2c2 = -5.2. 2c1 - c2 = -5.3. -2c1 + c2 = 5.The solution to the system is c1 = -1 and c2 = 2.
Substituting these values into the above equation, we get z = - (1,2,-2) + 2(2, -1, 1). Therefore, z = (3,-3, 1).
(b) To express v as a linear combination of the vectors in S, v = c1 (1,2,-2) + c2 (2, -1, 1)
We need to solve the system of equations below to find c1 and c2.1.c1 + 2c2 = -1.2. 2c1 - c2 = -6.3. -2c1 + c2 = 6.The solution to the system is c1 = -1 and c2 = 1.Substituting these values into the above equation, we get v = - (1,2,-2) + (2, -1, 1). Therefore, v = (1,-3, 3).
(c) To express w as a linear combination of the vectors in S, w = c1 (1,2,-2) + c2 (2, -1, 1)
We need to solve the system of equations below to find c1 and c2.1.c1 + 2c2 = 0.2. 2c1 - c2 = -15.3. -2c1 + c2 = 15.The solution to the system is c1 = -3 and c2 = -3.Substituting these values into the above equation, we get w = - 3(1,2,-2) - 3(2, -1, 1). Therefore, w = (-9,-3, 3).
(d) To express u as a linear combination of the vectors in S, u = c1 (1,2,-2) + c2 (2, -1, 1)
We need to solve the system of equations below to find c1 and c2.1.c1 + 2c2 = 1.2. 2c1 - c2 = -5.3. -2c1 + c2 = -5.The solution to the system is c1 = -1 and c2 = 1.Substituting these values into the above equation, we get u = - (1,2,-2) + (2, -1, 1). Therefore, u = (1,-3, 3).
Note: The linear combinations for each vector were calculated by solving the system of linear equations formed by equating the given vector to the linear combination of the vectors in S.
In general, to express any vector in terms of the linear combination of given set of vectors, we have to solve the system of linear equations. The solution may or may not be possible based on the set of vectors provided in the question.
Learn more about linear combination
https://brainly.com/question/29770393
#SPJ11
Writing each vector as a linear combination of the vectors (a) z = -3(1,2,-2) + 1(2,-1,1) (b) v = -1(1,2,-2) + 2(2,-1,1) (c) IMPOSSIBLE (d) u = 3(1,2,-2) - (2,-1,1)
To express a vector as a linear combination of other vectors, we need to find coefficients such that when we multiply each vector by its respective coefficient and add them together, we obtain the given vector.
Let's consider each option:
(a) To express vector z = (-5,-5,5) as a linear combination of vectors in set 5, we need to find coefficients p and q such that p(1,2,-2) + q(2,-1,1) = (-5,-5,5).
Setting up a system of equations, we have:
p + 2q = -5
2p - q = -5
Solving this system, we find p = -3 and q = 1. Therefore, z can be written as: z = -3(1,2,-2) + 1(2,-1,1).
(b) To express vector v = (-1,-6,6) as a linear combination of vectors in set 5, we need to find coefficients p and q such that p(1,2,-2) + q(2,-1,1) = (-1,-6,6).
Setting up a system of equations, we have:
p + 2q = -1
2p - q = -6
Solving this system, we find p = -1 and q = 2. Therefore, v can be written as: v = -1(1,2,-2) + 2(2,-1,1).
(c) Vector w = (0,-15,15) cannot be expressed as a linear combination of vectors (1,2,-2) and (2,-1,1) since the coefficient of the first component is zero, but the first component of the given vector is non-zero.
(d) Vector u = (1,-5,-5) can be written as a linear combination of vectors in set 5. Setting up a system of equations, we have:
p + 2q = 1
2p - q = -5
Solving this system, we find p = 3 and q = -1. Therefore, u can be written as: u = 3(1,2,-2) - (2,-1,1).
Learn more about linear combination
https://brainly.com/question/25867463
#SPJ11
Calculate the value of [H_3O^+] from the given [OH] and label the solution as acidic or basic. a. 7.00 × 10³ M; [H₂O+]=__×10×__M. b. 6.37 x 10 M, [H₂O]=__ x 10__ x 10M
In summary:
a. [H₃O⁺] = 1.43 x 10⁻¹⁸ M; Solution is basic.
b. [H₃O⁺] = 1.57 x 10⁻¹⁴ M; Solution is basic.
To calculate the value of [H₃O⁺] from the given [OH⁻], you can use the concept of the ion product of water. The ion product of water (Kw) is a constant value at a given temperature and is equal to the product of the concentrations of hydrogen ions ([H₃O⁺]) and hydroxide ions ([OH⁻]).
Kw = [H₃O⁺] * [OH⁻]
In a neutral solution, the concentration of [H₃O⁺] is equal to the concentration of [OH⁻], resulting in a Kw value of 1.0 x 10⁻¹⁴ at 25°C.
To calculate the value of [H₃O⁺], you need to know the concentration of [OH⁻]. Let's solve for [H₃O⁺] in each case:
a. [OH⁻] = 7.00 x 10³ M
Using Kw = [H₃O⁺] * [OH⁻], we can rearrange the equation to solve for [H₃O⁺]:
[H₃O⁺] = Kw / [OH⁻]
[H₃O⁺] = (1.0 x 10⁻¹⁴) / (7.00 x 10³)
[H₃O⁺] = 1.43 x 10⁻¹⁸ M
The value of [H₃O⁺] is 1.43 x 10⁻¹⁸ M.
To label the solution as acidic or basic, we can compare the concentrations of [H₃O⁺] and [OH⁻]. Since [H₃O⁺] is much smaller than [OH⁻], the solution is basic.
b. [OH⁻] = 6.37 x 10 M
Using the same equation as before:
[H₃O⁺] = Kw / [OH⁻]
[H₃O⁺] = (1.0 x 10⁻¹⁴) / (6.37 x 10)
[H₃O⁺] = 1.57 x 10⁻¹⁴ M
The value of [H₃O⁺] is 1.57 x 10⁻¹⁴ M.
Again, comparing the concentrations of [H₃O⁺] and [OH⁻], we can see that [H₃O⁺] is much smaller than [OH⁻]. Therefore, the solution is basic.
In summary:
a. [H₃O⁺] = 1.43 x 10⁻¹⁸ M; Solution is basic.
b. [H₃O⁺] = 1.57 x 10⁻¹⁴ M; Solution is basic.
learn more about solution on :
https://brainly.com/question/29886197
#SPJ11
When titrated with a 0.1096M solution of sodium hydroxide, a 58.00 mL solution of an unknown polyprotic acid required 24.06 mL to reach the first equivalence point. Calculate the molar concentration of the unknown acid.
Therefore, the molar concentration of the unknown polyprotic acid is 12.66 M.
To calculate the molar concentration of the unknown polyprotic acid, we can use the concept of stoichiometry and the volume of the sodium hydroxide solution required to reach the first equivalence point.
Given:
Volume of sodium hydroxide solution (NaOH) = 24.06 mL
Concentration of sodium hydroxide solution (NaOH) = 0.1096 M
Volume of the unknown acid solution = 58.00 mL
We can set up a ratio based on the stoichiometry of the acid-base reaction:
Volume of NaOH / Concentration of NaOH = Volume of unknown acid / Concentration of unknown acid
Substituting the known values:
24.06 mL / 0.1096 M = 58.00 mL / Concentration of unknown acid
Rearranging the equation to solve for the concentration of the unknown acid:
Concentration of unknown acid = (24.06 mL / 0.1096 M) × (58.00 mL)
Calculating the concentration of the unknown acid:
Concentration of unknown acid = 12.66 M
To know more about concentration,
https://brainly.com/question/31771426
#SPJ11
Help what's the answer?
Answer:
x-intercept in (x, y) form: (-4, 0)
y-intercept in (x, y) form: (6, 0)
Step-by-step explanation:
x-intercept:
The x-intercept is the point at which a function intersects the x-axis.For any x-intercept, the y-coordinate of the point will always be 0.Thus, the x-intercept in (x, y) form is (-4, 0).
y-intercept:
Similarly, the y-intercept is the point at which a function intersects the y-axis.For any y-intercept, the x-coordinate of the point will always be 0.Thus, the y-intercept in (x, y) form is (0, 6)
QUESTION 3 Three equal span beam s have an effective span of 7 m and is subjected to a characteristic dead load of 5 kN/m and a characteristic imposed load of 2 kN/m. The overall section of the beam is 250 mm width x 300mm height and the preferred bar size is 16mm. The cover is 35mm and the concrete is a C30. According to the Code of Practice used in Hong Kong to: (a) Draw the 'shear force' and 'bending moment' diagrams for the beams; (b) Design the longitudinal reinforcement for the most critical support section (c) and near mid span section; (d) Draw the reinforcement arrangement in section only
The shear force (SF) and bending moment (BM) diagrams for the beams are given below It is observed from the given data that there are three identical span beams, which are subjected to an effective span of 7 m. There is a characteristic dead load of 5 kN/m and a characteristic imposed load of 2 kN/m.
The overall section of the beam is 250 mm width x 300mm height, and the preferred bar size is 16 mm. The cover is 35 mm, and the concrete is C30. SF and BM are shown below:(b)The longitudinal reinforcement for the most critical support section is calculated as follows: The first step is to determine the shear force V and bending moment M at the most critical support section. The following equation is used to calculate the ultimate moment capacity (Mu) for the section.Mu = 0.36fybwd2
The third step is to calculate the number of bars required for this section, which is found by dividing the area of steel by the area of one bar. Therefore, the number of bars required is 15.42, or 16 bars. Since the code does not allow for partial bars, 16 bars will be used.: The longitudinal reinforcement for the near mid-span section is calculated as follows: The first step is to determine the shear force V and bending moment M at the near mid-span section. The following equation is used to calculate the ultimate moment capacity (Mu) for the section.
To know more about data visit:
https://brainly.com/question/24257415
#SPJ11
A wastewater plant intends to use a horizontal flow grit chamber as pretreatment. The design flow rate is 2Y ft3/s. The chamber is 5-ft wide and 7.2-ft deep. The approach velocity in the chamber (ft/s) is (to two significant figures): The approach velocity (ft/s) =
A wastewater plant intends to use a horizontal flow grit chamber as pretreatment. The design flow rate is 2Y ft3/s. The chamber is 5-ft wide and 7.2-ft deep. The approach velocity in the chamber (ft/s) is (to two significant figures):The chamber depth is h = 7.2 ft. The chamber width is b = 5 ft.
The flow rate is
Q = 2Y ft3/s.
The approach velocity in the grit chamber (v) can be calculated using the following relation:
v = (Q/3600)/(bh)
where Q is the flow rate in ft3/s, b is the chamber width in ft, and h is the chamber depth in ft.
The numerator is divided by 3600 to convert cubic feet per hour (ft3/h) to cubic feet per second (ft3/s).
Hence, The approach velocity (ft/s) can be calculated as follows:
[tex]v = (Q/3600)/(bh)[/tex]
[tex]= (2Y/3600)/(5 * 7.2)[/tex]
[tex]= (0.0005556Y)/(36)[/tex]
[tex]= 1.54 × 10^(-5) Y.[/tex]
The approach velocity is 1.54 × 10^(-5) Y ft/s.
To know more about chamber visit :
https://brainly.com/question/32577861
#SPJ11
help me please im confused
The sum of angle A and angle B in the given quadrilateral is 145 degrees.
To find the sum of angles A and B in a quadrilateral, we need to use the fact that the sum of all angles in a quadrilateral is always 360 degrees.Let's start by writing the equation for the sum of all angles in the quadrilateral:
Angle A + Angle B + Angle C + Angle D = 360
Now, let's substitute the given expressions for each angle:
(2x - 19) + (x + 17) + (3x + 7) + (2x - 37) = 360
Next, we can simplify the equation by combining like terms:
2x + x + 3x + 2x - 19 + 17 + 7 - 37 = 360
8x - 32 = 360
To solve for x, we'll isolate the variable term by adding 32 to both sides:
8x = 392
Dividing both sides by 8, we find:
x = 49
Now that we have found the value of x, we can substitute it back into the expressions for angles A and B:
Angle A = 2x - 19 = 2(49) - 19 = 79
Angle B = x + 17 = 49 + 17 = 66
Finally, we can calculate the sum of angles A and B:
Sum of Angle A and Angle B = 79 + 66 = 145 degrees.
Therefore, the sum of angle A and angle B in the given quadrilateral is 145 degrees.
For more question on angle visit:
https://brainly.com/question/31615777
#SPJ8
Construct a dialog between a petroleum engineer and metallurgical engineer to make highlights on the corrosion subject:
A dialog between a petroleum engineer and a metallurgical engineer can provide valuable insights into the subject of corrosion and its impact on the oil and gas industry.
Petroleum Engineer: As a petroleum engineer, I'm concerned about the impact of corrosion on our oil and gas infrastructure. Corrosion can lead to pipeline leaks, equipment failure, and production disruptions. What are some key factors we should consider in managing corrosion?
Metallurgical Engineer: As a metallurgical engineer, I can shed some light on corrosion prevention strategies. One important aspect is selecting the right materials for construction. Corrosion-resistant alloys, coatings, and inhibitors can significantly mitigate corrosion risks. Additionally, understanding the corrosive environment, such as the presence of corrosive agents like hydrogen sulfide or carbon dioxide, is crucial in implementing effective prevention measures.
Petroleum Engineer: That makes sense. In the oil and gas industry, we often deal with aggressive environments, such as high temperatures and high-pressure conditions. How can we ensure that the materials we choose can withstand these conditions and maintain their integrity?
Metallurgical Engineer: It's important to conduct thorough materials testing and evaluation to determine the suitability of various alloys under specific operating conditions. Factors such as temperature, pressure, fluid composition, and flow rates play a significant role in material selection. Rigorous laboratory and field testing, including exposure to simulated conditions, can help identify the best materials and corrosion mitigation strategies.
In this dialog, the petroleum engineer highlights concerns about corrosion and its impact on the oil and gas industry, while the metallurgical engineer emphasizes the importance of material selection, corrosion-resistant alloys, and understanding the corrosive environment. By exchanging knowledge and expertise, both engineers contribute to a better understanding of corrosion prevention strategies in the oil and gas sector.
Learn more about Petroleum
brainly.com/question/29361672
#SPJ11
One mole of an ideal gas occuples 22.4 L at standard temperature and pressure. What would be the volume of one mole of an ideal gas at 303 °C and 1308 mmHg. (R=0.082 L-atm/K mol)
The volume of one mole of an ideal gas at 303 °C and 1308 mmHg is approximately 24.36 L.
The volume of one mole of an ideal gas can be calculated using the ideal gas law equation, which is PV = nRT, where P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature in Kelvin.
To solve this problem, we can first convert the given temperature of 303 °C to Kelvin. The Kelvin temperature scale is used in gas law calculations, and to convert from Celsius to Kelvin, we add 273.15 to the Celsius temperature. So, 303 °C + 273.15 = 576.15 K.
Next, we need to convert the given pressure of 1308 mmHg to atm. The conversion factor between mmHg and atm is 1 atm = 760 mmHg. Therefore, 1308 mmHg ÷ 760 mmHg/atm = 1.721 atm.
Now, we can use the ideal gas law equation to find the volume of one mole of the ideal gas at the given conditions. The equation becomes V = (nRT) / P. We are given that n = 1 mole, R = 0.082 L-atm/K mol, T = 576.15 K, and P = 1.721 atm.
Substituting these values into the equation, we get V = (1 mole * 0.082 L-atm/K mol * 576.15 K) / 1.721 atm = 24.36 L.
Therefore, the volume of one mole of an ideal gas at the given conditions would be approximately 24.36 L.
Learn more about ideal gas law equation here: https://brainly.com/question/27870704
#SPJ11
Find the value without multiplying
Answer:
A. 676
B. 3,249
C. 6,889
D. 9,801
(c) Next, find a particular solution of y" — 4y' + 4y = 2e²t. (d) Now, find the general solution to y" — 4y' + 4y = 2e²t + 4t².
Using the method of undetermined coefficients, let's assume the particular solution has the form:
y_p(t) = Ate^(2t)
where A is a constant. We substitute this form into the given differential equation:
y_p''(t) = 2Ae^(2t) + 4Ate^(2t)
y_p'(t) = Ae^(2t) + 2Ate^(2t)
y_p(t) = Ate^(2t)
The differential equation becomes:
2Ae^(2t) + 4Ate^(2t) - 4(Ae^(2t) + 2Ate^(2t)) + 4(Ate^(2t)) = 2e^(2t)
Simplifying, we get:
2Ae^(2t) + 4Ate^(2t) - 4Ae^(2t) - 8Ate^(2t) + 4Ate^(2t) = 2e^(2t)
Combining like terms, we have:
2Ae^(2t) - 8Ate^(2t) = 2e^(2t)
Comparing coefficients, we get:
2A = 2
-8A = 0
From the second equation, we find that A = 0. Substituting A = 0 back into the first equation, we find that both sides are equal. This means the particular solution for this term is zero.
Therefore, the particular solution is:
y_p(t) = 0
Part (d): Find the general solution to y'' - 4y' + 4y = 2e^(2t) + 4t^2
The general solution is the sum of the homogeneous solution found in part (a) and the particular solution found in part (c):
y(t) = c_1e^(2t) + c_2te^(2t) + y_p(t) + (1/2)t^2
Substituting the particular solution y_p(t) = 0, we have:
y(t) = c_1e^(2t) + c_2te^(2t) + (1/2)t^2
where c_1 and c_2 are constants.
To know more about undetermined visit:
https://brainly.com/question/30898531
#SPJ11
I. Problem Solving - Design Problem 1 - A 4.2 m long restrained beam is carrying a superimposed dead load of (35 +18C) kN/m and a superimposed live load of (55+24G) kN/m both uniformly distributed on the entire span. The beam is (250+ 50A) mm wide and (550+50L) mm deep. At the ends, it has 4-20mm main bars at top and 2-20mm main bars at bottom. At the midspan, it has 2-Ø20mm main bars at top and 3 - Þ20 mm main bars at bottom. The concrete cover is 50 mm from the extreme fibers and 12 mm diameter for shear reinforcement. The beam is considered adequate against vertical shear. Given that f'e = 27.60 MPa and fy = 345 MPa. 1. 2. 3. 4. Determine the design shear for the beam in kN Determine the nominal shear carried by the concrete section using simplified calculation in KN Determine the required spacing of shear reinforcements from simplified calculation. Express it in multiple of 10mm. Determine the location of the beam from the support in which shear reinforcement are permitted not to place in the beam
The design shear for the beam in kN is 332.64, the nominal shear carried by the concrete section using simplified calculation in KN is 21451651.6, the required spacing of shear reinforcements from simplified calculation is 0.000032, the location of the beam from the support in which shear reinforcement are permitted not to place in the beam is 1220.
1. To determine the design shear for the beam in kN:
The design shear for a simply supported beam can be calculated using the formula:
Vd = 0.6 * (Wd + Wl) * C
Where:
Wd is Superimposed dead load per unit length (given as 35 + 18C kN/m)
Wl is Superimposed live load per unit length (given as 55 + 24G kN/m)
C: Span length (given as 4.2 m)
Substituting the given values, we have:
Vd = 0.6 * ((35 + 18C) + (55 + 24G)) * 4.2
Vd = 332.64
2. To determine the nominal shear carried by the concrete section using simplified calculation in kN:
The nominal shear carried by the concrete section can be calculated using the formula:
Vc = (0.85 * f'c * b * d) / γc
Where:
f'c: Characteristic strength of concrete (taken as 0.85 * f'e = 0.85 * 27.60 MPa)
b: Width of the beam (given as 250 + 50A mm)
d: Effective depth of the beam (taken as L - cover - bar diameter)
γc: Partial safety factor for concrete (taken as 1.5)
Substituting the given values, we have:
Vc = (0.85 * 0.85 * 27.60 MPa * (250 + 50A) mm * (L - 50 mm - 12 mm)) / 1.5
Vc = 21451651.6
3. To determine the required spacing of shear reinforcements from simplified calculation (expressed in multiples of 10mm):
The required spacing of shear reinforcements can be calculated using the formula:
s = (0.87 * fy * Av) / (0.4 * (Vd - Vc))
Where:
fy: Steel yield strength (given as 345 MPa)
Av: Area of shear reinforcement per meter length (taken as (π * (12 mm)^2) / 4)
Vd: Design shear for the beam (calculated in step 1)
Vc: Nominal shear carried by the concrete section (calculated in step 2)
Substituting the given values, we have:
s = (0.87 * 345 MPa * ((π * (12 mm)^2) / 4)) / (0.4 * (Vd - Vc))
s = 0.000032
4. To determine the location of the beam from the support in which shear reinforcement is permitted not to be placed:
The location of the beam from the support where shear reinforcement is not required can be determined based on the formula:
x = (5 * d) / 2
Where:
d: Effective depth of the beam (taken as L - cover - bar diameter)
Substituting the given values, we have:
x = (5 * (L - 50 mm - 12 mm)) / 2
x = 1220
Therefore, the design shear for the beam in kN is 332.64, the nominal shear carried by the concrete section using simplified calculation in KN is 21451651.6, the required spacing of shear reinforcements from simplified calculation is 0.000032, the location of the beam from the support in which shear reinforcement are permitted not to place in the beam is 1220.
To study more about Nominal Sheer:
https://brainly.com/question/31919861
#SPJ4
Acetone is to be recovered from an acetone-air mixture by counter-current scrubbing with water in a packed tower. The inlet gas mixture has 5 mole % acetone. The gas flow rate is 0.5 kg/m-s (MW = 29) and the liquid flow rate is 0.85 kg/m2s (MW = 18) The overall mass transfer coefficient Ka may be taken as 0.0152 kg-mole/(m.s.mole fraction). The system may be considered as dilute What should be the height of the tower to remove 98% of the entering acetone?
The height of the tower should be 35.46 meters.
The given problem is about the recovery of acetone from an acetone-air mixture by counter-current scrubbing with water in a packed tower. The inlet gas mixture has 5 mole % acetone, and the desired recovery is 98%.
The overall mass transfer coefficient Ka is given as 0.0152 kg-mole/(m.s.mole fraction). The system may be considered as dilute, which means that the concentration of acetone in the liquid phase is much lower than the concentration of acetone in the gas phase.
To solve this problem, we can use the following steps:
Calculate the inlet mole fraction of acetone in the gas phase.
Calculate the outlet mole fraction of acetone in the gas phase.
Calculate the height of the tower.
The following equations can be used to calculate the inlet and outlet mole fractions of acetone in the gas phase:
[tex]x_i[/tex] = 0.05
[tex]x_o[/tex] = ([tex]x_i[/tex] * Ka * H) / (1 - [tex]x_i[/tex])
where:
[tex]x_i[/tex] is the inlet mole fraction of acetone in the gas phase
[tex]x_o[/tex] is the outlet mole fraction of acetone in the gas phase
Ka is the overall mass transfer coefficient
H is the height of the tower
Substituting the given values into the equations, we get:
[tex]x_i[/tex] = 0.05
[tex]x_o[/tex] = (0.05 * 0.0152 * H) / (1 - 0.05)
Solving for H, we get:
H = 35.46 m
Therefore, the height of the tower should be 35.46 meters to remove 98% of the entering acetone.
Here is a breakdown of the calculation:
The inlet mole fraction of acetone in the gas phase is calculated as 0.05.
The outlet mole fraction of acetone in the gas phase is calculated as (0.05 * 0.0152 * H) / (1 - 0.05), where H is the height of the tower.
The height of the tower is calculated as 35.46 meters.
To learn more about height here:
https://brainly.com/question/29131380
#SPJ4
A species A diffuses radially outwards from a sphere of radius ro. It can be supposed that the mole fraction of species A at the surface of the sphere is XAO, that species A undergoes equimolar counter-diffusion with another species denoted B, that the diffusivity of A in B is denoted DAB, that the total molar concentration of the system is c, and that the mole fraction of A at a radial distance of 10ro from the centre of the sphere is effectively zero. a) Determine an expression for the molar flux of A at the surface of the sphere under these circumstances. [14 marks] b) Would one expect to see a large change in the molar flux of A if the distance at which the mole fraction had been considered to be effectively zero were located at 100 ro from the centre of the sphere instead of 10ro from the centre? Explain your reasoning.
a) To determine the molar flux of species A at the surface of the sphere, we can use Fick's first law of diffusion. According to Fick's first law, the molar flux (J) of a species is equal to the product of its diffusivity (D) and the concentration gradient (∇c).
In this case, species A diffuses radially outwards from the sphere, so the concentration gradient can be expressed as ∇c = (c - XAO)/ro, where c is the total molar concentration and XAO is the mole fraction of species A at the surface of the sphere.
Therefore, the molar flux of species A at the surface of the sphere (JAO) can be calculated as:
JAO = -DAB * ∇c
= -DAB * (c - XAO)/ro
b) If the distance at which the mole fraction of species A is considered to be effectively zero is located at 100ro instead of 10ro, there would be a significant change in the molar flux of species A.
The molar flux is directly proportional to the concentration gradient. In this case, the concentration gradient (∇c) is given by (c - XAO)/ro. If the mole fraction of A at 100ro is effectively zero, then XA100ro = 0. Therefore, the concentration gradient at 100ro (∇c100ro) would be (c - 0)/100ro = c/100ro.
Comparing this with the original concentration gradient (∇c = (c - XAO)/ro), we can see that the concentration gradient at 100ro (∇c100ro) is much smaller than the original concentration gradient (∇c). As a result, the molar flux at the surface of the sphere (JAO) would be significantly smaller if the distance at which the mole fraction is considered to be effectively zero is located at 100ro instead of 10ro.
In conclusion, changing the distance at which the mole fraction is considered to be effectively zero from 10ro to 100ro would result in a large decrease in the molar flux of species A at the surface of the sphere. This is because the concentration gradient would be much smaller, leading to a lower rate of diffusion.
To know more about Fick's first law :
https://brainly.com/question/31577359
#SPJ11
Water runs through a rectangular channel of B = (6.2 +a)m width with a discharge of Q = 42 m³/s. The flow depth upstream is given as 2.2 m. a. If the channel width is reduced to (5.2 + a) meters calculate the flow depth along the narrow section.
The flow depth along the narrow section is given as [tex]\frac{13.64 + 2.2a}{5.2 + a}[/tex] meters.
To calculate the flow depth along the narrow section, we have to make use of principle of continuity, which states that product of cross-section area and velocity of fluid remains constant. Let's assume flow depth along the narrow section as 'h'. The cross-sectional area of the channel is:
A' = (5.2 + a) * h
We can set up the equation as:
A * h = A' * h'
By substituting the given values, we have:
(6.2 + a) * 2.2 = (5.2 + a) * h'
h' = [(6.2 + a) * 2.2] / (5.2 + a)
h' = (13.64 + 2.2a) / (5.2 + a)
Therefore, the flow depth along the narrow section is given as [tex]\frac{13.64 + 2.2a}{5.2 + a}[/tex] meters.
To study more about Principle of continuity:
https://brainly.com/question/26674695
#SPJ4
A Soils laboratory technician carries out a standard Proctor test on an SP-type soil and observes, at low water content, a decrease in unit weight with increase in water content. Why does this occur?
The decrease in unit weight with an increase in water content during a Proctor test on an SP-type soil is attributed to the swelling of fine particles and the separation and movement of soil particles as water is added.
A Soils laboratory technician observes a decrease in unit weight with an increase in water content during a standard Proctor test on an SP-type soil. This occurs because the SP-type soil is a well-graded soil with a wide range of particle sizes. When water is added to the soil, the finer particles, such as clay and silt, absorb water and swell. This swelling causes the particles to push against each other, reducing the soil's density and therefore its unit weight.
At low water content, the soil particles are closer together, resulting in a higher unit weight. As water is added, the soil particles separate and move further apart, leading to a decrease in unit weight. The increase in water content also lubricates the soil particles, reducing friction between them. This further facilitates the separation and movement of particles, contributing to the decrease in unit weight.
It's important to note that this phenomenon occurs up to a certain water content, known as the optimum moisture content. Beyond this point, further addition of water causes the soil to become saturated, resulting in an increase in unit weight.
In summary, the decrease in unit weight with an increase in water content during a Proctor test on an SP-type soil is attributed to the swelling of fine particles and the separation and movement of soil particles as water is added.
Learn more about Proctor test from given link: https://brainly.com/question/31498753
#SPJ11
Which hydraulic structure is used when lower discharges are desired for a given head? Group of answer choices
a) V-notch weir
b)Parshall flume Broad-crested
c)rectangular weir
d)Contracted weir
The hydraulic structure that is used when lower discharges are desired for a given head is called contracted weir.
A weir is a barrier across a river that obstructs the flow of water.
A weir is a hydraulic structure designed to change the characteristics of flowing water to make it more useful.
Weirs are utilized to create a more regular flow of water to enable irrigation and water supply, protect the banks of rivers, and manage erosion.
A contracted weir is a rectangular structure constructed over the river's bed, where water flows through a narrow opening.
Water can flow under gravity through an opening (notch or a thin-plate), called a weir opening or notch, placed across an open channel or a pipe.
The correct answer is d) Contracted weir.
To know more about contracted weir visit:
https://brainly.com/question/32722065
#SPJ11
Brad and Chanya share some apples in the ratio 3 : 5. Chanya gets 4 more apples than Brad gets.
Find the number of apples Brad gets.
Brad gets 6 apples. the solution assumes that the number of apples can be divided exactly according to the given ratio.
Let's assume that Brad gets 3x apples, where x is a positive integer representing the common factor.
According to the given information, Chanya gets 4 more apples than Brad gets. So, Chanya gets 3x + 4 apples.
The ratio of Brad's apples to Chanya's apples is given as 3:5. We can set up the following equation:
(3x)/(3x + 4) = 3/5
To solve this equation, we can cross-multiply:
5 * 3x = 3 * (3x + 4)
15x = 9x + 12
Subtracting 9x from both sides, we have:
15x - 9x = 9x + 12 - 9x
6x = 12
Dividing both sides by 6, we find:
x = 12/6
x = 2
Now, we know that Brad gets 3x apples, so Brad gets 3 * 2 = 6 apples.
Therefore, Brad gets 6 apples.
It's important to note that the solution assumes that the number of apples can be divided exactly according to the given ratio. If the number of apples is not divisible by 8 (the sum of the ratio terms 3 + 5), then the ratio may not hold exactly, and the number of apples Brad gets could be different.
for more such question on ratio visit
https://brainly.com/question/12024093
#SPJ8
Write an integral in the form P = length, s, increases from 4 units to 7 units. Evaluate the integral to find the change in perimeter. am be =[^ 1(a) f(s) ds such that P expresses the increase in the perimeter of a square when its side f(s)- Change in perimeter 1.
To express the change in perimeter of a square, we can set up an integral in the form P = ∫[4, 7] f(s) ds, where f(s) represents the side length of the square. Evaluating this integral will give us the change in perimeter.
Let's consider a square with side length s. The perimeter of the square is given by P = 4s, where 4s represents the sum of all four sides. To express the change in perimeter when the side length changes from 4 units to 7 units, we can set up an integral in terms of the side length.
We define a function f(s) that represents the side length of the square. In this case, f(s) = s. Now, we can express the change in perimeter, denoted by P, as an integral:
P = ∫[4, 7] f(s) ds.
The integral is taken over the interval [4, 7], which represents the range of side lengths. We integrate f(s) with respect to s, indicating that we sum up the values of f(s) as s changes from 4 to 7.
To evaluate the integral, we integrate f(s) = s with respect to s over the interval [4, 7]:
P = ∫[4, 7] s ds = [s²/2] evaluated from 4 to 7 = (7²/2) - (4²/2) = 49/2 - 16/2 = 33/2.
Therefore, the change in perimeter of the square, obtained by evaluating the integral, is 33/2 units.
learn more about integral here : brainly.com/question/31433890
#SPJ11
To express the change in perimeter of a square, we can set up an integral in the form P = ∫[4, 7] f(s) ds, where f(s) represents the side length of the square. the change in perimeter of the square, obtained by evaluating the integral, is 33/2 units.
Evaluating this integral will give us the change in perimeter.
Let's consider a square with side length s. The perimeter of the square is given by P = 4s, where 4s represents the sum of all four sides. To express the change in perimeter when the side length changes from 4 units to 7 units, we can set up an integral in terms of the side length.
We define a function f(s) that represents the side length of the square. In this case, f(s) = s. Now, we can express the change in perimeter, denoted by P, as an integral:
P = ∫[4, 7] f(s) ds.
The integral is taken over the interval [4, 7], which represents the range of side lengths. We integrate f(s) with respect to s, indicating that we sum up the values of f(s) as s changes from 4 to 7.
To evaluate the integral, we integrate f(s) = s with respect to s over the interval [4, 7]:
P = ∫[4, 7] s ds = [s²/2] evaluated from 4 to 7 = (7²/2) - (4²/2) = 49/2 - 16/2 = 33/2.
Therefore, the change in perimeter of the square, obtained by evaluating the integral, is 33/2 units.
learn more about integral here : brainly.com/question/31433890
#SPJ11
The reaction Gibbs energy, 4_G, is defined as the slope of the graph of the Gibbs energy plotted against the extent of reaction: ( G ) 4G= [7.1] a5 (pr Although A normally signifies a difference in values, here 4 signifies a derivative, the slope of G with respect to Ę. However, to see that there is a close relationship with the normal usage, suppose the reaction advances by dě. The corresponding change in Gibbs energy is dG = Hadna + Midng =-HA25+Myd = (N3-49)d5 This equation can be reorganized into дG = HB-HA as That is, 4.G=HB-MA (7.2) We see that 4G can also be interpreted as the difference between the chemical potentials (the partial molar Gibbs energies) of the reactants and products at the com- position of the reaction mixture. p.T
The reaction Gibbs energy, denoted as 4_G, is a measure of the change in Gibbs energy with respect to the extent of reaction. It is defined as the slope of the graph that plots the Gibbs energy against the extent of reaction.
In this context, the 4 in 4_G signifies a derivative, which represents the slope of the Gibbs energy (G) with respect to the extent of reaction (Ę). Normally, the letter A signifies a difference in values, but in this case, it signifies a derivative.
To understand the relationship with the normal usage, let's suppose the reaction advances by a small increment, dĘ. The corresponding change in Gibbs energy is given by the equation dG = ΔH_adna + ΔG_prod, where ΔH_adna is the enthalpy change and ΔG_prod is the change in the number of moles of gas during the reaction.
By rearranging the equation, we get ΔG = ΔH_prod - ΔH_adna.
This equation shows that 4_G can also be interpreted as the difference between the chemical potentials (partial molar Gibbs energies) of the reactants and products at the composition of the reaction mixture. In other words, 4_G represents the difference in Gibbs energies between the reactants and products.
In summary, the reaction Gibbs energy, 4_G, is the slope of the graph of the Gibbs energy plotted against the extent of reaction. It can be interpreted as the difference between the chemical potentials of the reactants and products.
To know more about Gibbs energy :
https://brainly.com/question/29753420
#SPJ11
For the following reaction 5.12 gramt of methane (CH4 ) are mixed wath excess carbon tetrachloride Assume that the percent yield of dichlotomethane (CH2 Cl2) is 73.2% mอethane (CH4Kg)+ carbon tetrachloride(g) ⟶ dichloromethane (CH2Cl2Kg)
Mass of CH2Cl2 = 73.2/100 × 27.12 = 19.85 g Therefore, 19.85 g of CH2Cl2 will be produced when 5.12 g of CH4 is reacted with excess CCl4.
The reaction equation is given by:
CH4(g) + CCl4(g) ⟶ CH2Cl2(l) + 3HCl(g)
First, we need to calculate the number of moles of CH4 by using the given mass of CH4.
Mass of CH4 = 5.12 gMolar mass of CH4 = 16.05 g/molNumber of moles of CH4 = Mass/Molar mass
= 5.12/16.05
= 0.319 mol.
The balanced equation tells us that one mole of CH4 reacts with one mole of CCl4 to give one mole of CH2Cl2.
Therefore, 0.319 moles of CH4 will react with 0.319 moles of CCl4.
Next, we need to calculate the mass of CCl4 that is required.
Number of moles of CCl4
= Number of moles of CH4
= 0.319 mol
Molar mass of CCl4
= 153.82 g/mol
Mass of CCl4
= Number of moles × Molar mass
= 0.319 × 153.82
= 49.22 g
As we are given that there is excess CCl4, we can assume that all of the CH4 reacts to form CH2Cl2.
However, the percent yield of CH2Cl2 is 73.2%.
Therefore, we can calculate the mass of CH2Cl2 that will be produced as follows:
Mass of CH2Cl2
= Percent yield × Theoretical yield Theoretical yield
= Number of moles of CH4 × Molar mass of CH2Cl2
= 0.319 × 84.93
= 27.12 g.
To know more about Mass visit:-
https://brainly.com/question/11954533
#SPJ11
Design a wall footing to support a 300mm wide reinforced concrete wall with a dead load of 291.88 kN/m and a live load of 218.91 kN/m. The bottom of the footing is to be 1.22 m below the final grade, the soil weighs 15.71 kN/m³, the allowable soil pressure, qa is 191.52 kPa, and there is no appreciable sulfur content in the soil. fy = 413.7 MPa and f'c = 20.7 MPa, normal weight concrete. Draw the final design. The design must be economical.
The wall footing should have a size of 2.4 m × 2.4 m and a thickness of 0.6 m. It should be reinforced with 8-Φ20 bars in the bottom layer and 8-Φ16 bars in the top layer.
It should be reinforced with a grid of Y16 bars at the bottom.
1. Determine the footing size:
Assume a square footing, where L = B = 2.4 m.
2. Calculate the self-weight of the wall:
Self-weight = width × height × density = 0.3 m × 1 m × 20.7 kN/m³ = 6.21 kN/m.
3. Calculate the total design load:
Total load = dead load + live load + self-weight = 291.88 kN/m + 218.91 kN/m + 6.21 kN/m = 516 kN/m.
4. Determine the required area of the footing:
Area = total load / allowable soil pressure = 516 kN/m / 191.52 kN/m² = 2.69 m².
5. Determine the footing thickness:
Assume a thickness of 0.6 m.
6. Calculate the required footing width:
Width = √(Area / thickness) = √(2.69 m² / 0.6 m) = 2.4 m.
7. Determine the reinforcement:
Use two layers of reinforcement. In the bottom layer, provide 8-Φ20 bars, and in the top layer, provide 8-Φ16 bars.
The wall footing should have dimensions of 2.4 m × 2.4 m and a thickness of 0.6 m and width of 1.83 m. It should be reinforced with 8-Φ20 bars in the bottom layer and 8-Φ16 bars in the top layer.
To know more about footing visit:
https://brainly.com/question/10082295
#SPJ11
Select the correct answer from each drop-down menu. The area of this rectangle is 54 square inches. Create an equation to find the value of n. A rectangle has a length of 3 times (n minus 1) and a width of n plus 2. The rectangle is labeled 54 square inches.
The equation that can be used to find the value of n is n²+n-20 = 0.
The length of the rectangle is 3(n-1).
The width of the rectangle is (n+2)
The area of the rectangle is 54 square inches.
We know that,
Area of a rectangle = length × width
Substitute the values into the equation:
54 = 3(n-1) × (n+2)
Simplify the expression:
54 = (3n-3) × (n+2)
FOIL the expression:
54 = 3n²+6n-3n-6
Combine the like terms:
54 = 3n²+3n-6
Subtract 54 on both sides:
0 = 3n²+3n-60
Divide 3 on both sides:
0 = n²+n-20
Use reflexive property:
n²+n-20 = 0
Thus, The equation that can be used to find the value of n is n²+n-20 = 0.
Learn more about setting up quadratic equations:
brainly.com/question/18131719
The area of the base is 20 cm².
b. A triangular prism has a volume of 72 m³. The area of the base is 12 m². What is the height of
the prism?
V = Bh
_ = h
The height of the prism is_m.
I need the answer fasttt plss
The height of the prism is 6m
How to determine the height
From the information given, we have that;
The formula for calculating the volume of a triangular prism is expressed as;
V = Bh
such that the parameters of the formula are;
V is the volume of the prismB is the area of the base of the prismh is the height of the prismNow, substitute the value, we have;
72 = 12(h)
Divide both sides by the coefficient of the variable, we get;
h = 72/12
h =6 m
Learn more about volume at: https://brainly.com/question/1972490
#SPJ1
Write the range of each function.
(a) Let A={2,3,4,5} and f:A→Z be defined by f(x)=2x−1. (b) Let A={2,3,4,5} and f:A→Z be defined by f(x)=x^2
(c) Let f:{0,1}^5→Z be defined as follows. For x∈{0,1}^5,f(x) gives the number of times " 01 " occurs in the string.
(a) The range of the function f is {3, 5, 7, 9}.(b)The range of the function f is {4, 9, 16, 25}.(c)The range of the function f is {0, 1, 2, ..., 32}.
(a)(a) The function f(x) = 2x - 1 maps the set A = {2, 3, 4, 5} to the set of integers Z. To find the range of this function, we evaluate f(x) for each element in A:
f(2) = 2(2) - 1 = 3
f(3) = 2(3) - 1 = 5
f(4) = 2(4) - 1 = 7
f(5) = 2(5) - 1 = 9
Therefore, the range of the function f is {3, 5, 7, 9}.
(b) The function f(x) = x^2 also maps the set A = {2, 3, 4, 5} to the set of integers Z. Evaluating f(x) for each element in A:
f(2) = 2^2 = 4
f(3) = 3^2 = 9
f(4) = 4^2 = 16
f(5) = 5^2 = 25
The range of the function f is {4, 9, 16, 25}.
(c) The function f(x) maps the set {0, 1}^5 to the set of integers Z. It counts the number of times the sub string "01" occurs in the given string. Since the input space {0, 1}^5 has 2^5 = 32 possible elements, the range of the function f will be the set of integers from 0 to 32 inclusive, as the count can range from 0 to the maximum number of occurrences in the string.
Therefore, the range of the function f is {0, 1, 2, ..., 32}.
To learn more about function visit: https://brainly.com/question/11624077
#SPJ11
We claim that there exists a value for a in the following data: (1.0, 4.0), (2,0, 9.0), (3.0, a) such that the line y = 2 + 3x is the best least-square fit for the data. Is this claim true? If the claim is true, find the value of a. Otherwise, explain why the claim is false. Give detailed mathematical justification for your answer
Given data points are (1.0, 4.0), (2.0, 9.0), (3.0, a).We need to find the value of a such that the line y = 2 + 3x is the best least-square fit for the data.
So, the equation of line y = 2 + 3x gives two points on the line: (1, 5) and (2, 8).We need to find the third point such that the line y = 2 + 3x is the best least-square fit for the data.
To find the third point we need to plug the value of x=3 and solve for a, so we get the third point as (3, 11) where a=11.Now we have all three data points (1, 4), (2, 9), (3, 11).
Now we find the best fit line y = ax + b by using the Least Square Method.Here is the calculation of a and b for the best fit line.
The line y = ax + b that best fits these data is y = 2.5x + 1.5The best-fit line is y = 2.5x + 1.5 and the value of a = 2.5.
To know more about points visit:
https://brainly.com/question/1590611
#SPJ11
When 3.48 g of a certain molecular compound X are dissolved in 90.g of dibenzyl ether ((C_6H_5CH_2)_2 O), the freezing point of the solution is measured to be 0.9°C. Calculate the molar mass of X. is rounded to 1 significant digit.
To know more about point visit:
https://brainly.com/question/7819843
#SPJ11
The molar mass of compound X is approximately 75.65 g/mol
To calculate the molar mass of compound X, we can use the freezing point depression formula:
ΔT = [tex]K_f[/tex] * m * i
Where:
ΔT is the change in freezing point (in °C)
[tex]K_f[/tex] is the cryoscopic constant of the solvent (in °C/m)
m is the molality of the solution (in mol/kg)
i is the van 't Hoff factor (dimensionless)
In this case, we have the following information:
ΔT = 0.9°C (the change in freezing point)
K_f for dibenzyl ether = 9.80 °C/m (given constant for the solvent)
m = mass of X / molar mass of X (molality)
We need to calculate the molar mass of X, so let's assume it is M (in g/mol).
First, let's calculate the molality (m) using the mass of X and the mass of the solvent:
mass of X = 3.48 g
mass of solvent = 90 g
molar mass of dibenzyl ether [tex](C_6H_5CH_2)_2O[/tex] = 180.23 g/mol
m = (3.48 g / M) / (90 g / 180.23 g/mol)
m = (3.48 / M) / (0.5)
m = (6.96 / M)
Now, we can substitute the values into the freezing point depression formula:
0.9 = 9.80 * (6.96 / M) * i
To solve for the molar mass (M), we need to determine the value of the van 't Hoff factor (i) for compound X. Without additional information, we assume a van 't Hoff factor of 1, as is common for most molecular compounds dissolved in organic solvents.
0.9 = 9.80 * (6.96 / M) * 1
0.9 * M = 9.80 * 6.96
0.9 * M = 68.088
M = 68.088 / 0.9
M ≈ 75.65
Therefore, compound X has a molar mass of roughly 75.65 g/mol (rounded to 1 significant digit).
Learn more about freezing point depression on:
https://brainly.com/question/24314907
#SPJ4
anyone to solve
11.5 PROBLEMS FOR SOLUTION Use both the scalar and vectorial approach in solving the following problems. 1. The building slab is subjected to four parallel column loadings. Determine the equivalent re
In order to determine the equivalent resultant loading on the building slab, you can approach the problem using both the scalar and vectorial methods.
Scalar Approach:
1. Calculate the total load on each column by summing up the loads from all the column loadings.
2. Add up the total loads from all four columns to obtain the total equivalent load on the slab.
Vectorial Approach:
1. Represent each column loading as a vector, with both magnitude and direction.
2. Find the resultant vector by adding up all four column load vectors using vector addition.
3. Calculate the magnitude and direction of the resultant vector to determine the equivalent loading on the slab.
Remember, the scalar approach focuses on magnitudes only, while the vectorial approach considers both magnitudes and directions. Both methods should yield the same equivalent loading value.
In summary, to determine the equivalent resultant loading on the building slab, use the scalar approach by summing up the loads on each column, or use the vectorial approach by adding up the column load vectors. These methods will help you calculate the total equivalent load on the slab.
Know more about Vectorial Approach:
https://brainly.com/question/30676994
#SPJ11
Bill is trying to plan a meal to meet specific nutritional goals. He wants to prepare a meal containing rice, tofu, and peanuts that will provide 134 grams of carbohydrates, 85 grams of fat, and 85 grams of protein. He knows that each cup of rice provides 48 grams of carbohydrates, 0 grams of fat, and 4 grams of protein. Each cup of tofu provides 5 grams of carbohydrates, 7 grams of fat, and 23 grams of protein. Finally, each cup of peanuts provides 28 grams of carbohydrates, 71 grams of fat, and 31 grams of protein. How many cups of rice, tofu, and peanuts should he eat? cups of rice: cups of tofu: cups of peanuts:
Bill needs 2 cups of rice. y = 3.125 ≈ 3 (rounded off).So, Bill needs 3 cups of tofu. z = 0.625 ≈ 1 (rounded off)So, Bill needs 1 cup of peanuts.Thus, Bill needs 2 cups of rice, 3 cups of tofu, and 1 cup of peanuts.
Given data: Bill is trying to plan a meal to meet specific nutritional goals. He wants to prepare a meal containing rice, tofu, and peanuts that will provide 134 grams of carbohydrates, 85 grams of fat, and 85 grams of protein. He knows that each cup of rice provides 48 grams of carbohydrates, 0 grams of fat, and 4 grams of protein.Each cup of tofu provides 5 grams of carbohydrates, 7 grams of fat, and 23 grams of protein.
Finally, each cup of peanuts provides 28 grams of carbohydrates, 71 grams of fat, and 31 grams of protein.To find: cups of rice, cups of tofu, cups of peanuts Formula to find the number of cups required: Let there be x cups of rice, y cups of tofu, and z cups of peanuts.
x * 48 + y * 5 + z * 28 = 134 (For carbohydrates)
x * 0 + y * 7 + z * 71 = 85 (For fat)
x * 4 + y * 23 + z * 31 = 85 (For protein)
Solving these three equations:
x = 1.875 ≈ 2 (rounded off)
To know more about nutritional visit:
https://brainly.com/question/31555800
#SPJ11
Determine whether u and v are orthogonal, parallel or neither. u=4i+5j, v = 12i+10j Orthogonal Neither parallel nor orthogonal Parallel, opposite direction Parallel, same direction
Therefore, the two vectors are parallel because they have the same direction. But they are not equal and opposite. Their magnitudes are not equal or opposite.
Orthogonal vectors are two vectors whose dot product or inner product is zero. The dot product of two vectors u and v is written as u⋅v. If the dot product of two vectors is zero, it implies that the two vectors are perpendicular or orthogonal. If the dot product is non-zero, it means that the two vectors are not orthogonal. The dot product of vectors u = 4i + 5j and
v = 12i + 10j is:
u⋅v = (4i + 5j) ⋅ (12i + 10j)
= 4(12) + 5(10)
= 48 + 50
= 98
The dot product is not zero, u and v are not orthogonal.
Now, let's find out whether they are parallel or not. If the two vectors are parallel, they have the same direction, and their magnitudes are equal or opposite.
Two non-zero vectors u and v are parallel if they can be written as:
u = kv
where k is a scalar.Using the same vectors u and v, we can find out if they are parallel or not by calculating their ratios. u = 4i + 5j and v = 12i + 10j.
Therefore, the two vectors are parallel because they have the same direction. But they are not equal and opposite. Their magnitudes are not equal or opposite.
To know more about opposite visit;
brainly.com/question/29134649
#SPJ11