I. The resistivity of copper being 0.0185 mm²/m. II. The appropriate breaker to be used for the circuit should have a maximum current rating of 80 A and a breaking capacity of 50 kA. III. The thermal overload relay to be selected from the given list of relays for the following motor is LRD1508.
I. Data (10 points). A 22kW motor is connected to a 1600kVA transformer rated at 0.38kV and a line to line voltage of 380V. The cos ø = 0.85, and cable length is 200 m with a copper wire of 10 mm² with the resistivity of copper being 0.0185 mm²/m.
II. Circuit Breaker (10 points)The first step in circuit breaker selection is to determine the short-circuit current at the supply point. Then, the breaking capacity of the circuit breaker required to interrupt the short-circuit current is determined. The short-circuit current is calculated as follows: Isc = (3 × Un × k) / (Ud × √3)where Un = 0.38 kVk = 6% (0.06)Ud = 410 V (Voltage drop). Isc = (3 × 0.38 × 1000 × 0.06) / (410 × √3)Isc = 2.8 kA. The short-circuit current is 2.8 kA. The selection of the circuit breaker should be made in such a way that it should be able to interrupt the short-circuit current and also capable of handling the maximum load current.
III. Thermal Relay (10 points): The thermal overload relay to be selected from the given list of relays for the following motor is LRD1508.
Let's learn more about motor:
https://brainly.com/question/28852537
#SPJ11
Consider again a voltmeter connected across the second of two resistors R in series. Show that when the meter has the SAME resistance as each R, then the voltage should be 1.00V across the parallel pair. You may do this algebraically or using some value (say, 50.0kQ.) (5) 4. Explain why the voltage values in the table go to zero when the meter's resistance is LOW compared to the value of R. (
When a voltmeter with the same resistance as each resistor in a series circuit is connected across the second resistor, the voltage across the parallel pair is 1.00V.
When the meter's resistance is low compared to the value of R, most of the current flows through the meter, causing the voltage across the resistors to approach zero.
In a series circuit with two resistors, R₁ and R₂, and a voltmeter connected across the second resistor (R₂), the voltage across the parallel combination of R₁ and R₂ can be calculated using the voltage divider rule. The voltage divider rule states that the voltage across a resistor in a series circuit is proportional to its resistance.
Let's consider the case where the voltmeter has the same resistance as each resistor (R = R₁ = R₂). In this case, the total resistance of the circuit is doubled, resulting in half the current flowing through the resistors. Using Ohm's Law (V = IR), the voltage across each resistor would be half of the total voltage across the circuit.
Now, if we choose a specific resistance value, such as R = 50.0 kΩ, and assume a total voltage of 2.00V across the circuit, each resistor would have a voltage of 1.00V across it.
Since the voltmeter has the same resistance as each resistor, it would also have a voltage of 1.00V across it. Thus, the voltage across the parallel pair (R₁ and R₂) would be the sum of the voltages across each resistor, resulting in a voltage of 1.00V.
When the meter's resistance is low compared to the value of R, it effectively creates a parallel path with the resistors in the circuit. This means that a significant portion of the current flowing through the circuit will take the path of least resistance, bypassing the resistors.
In a parallel configuration, the total resistance decreases as more branches are added. In this case, the addition of the low resistance of the voltmeter creates a parallel path with the resistors, resulting in a significantly reduced equivalent resistance.
As a consequence, most of the current in the circuit will flow through the low resistance of the voltmeter.
According to Ohm's Law (V = IR), when the current passing through a resistance decreases, the voltage drop across that resistance also decreases.
Since most of the current is diverted through the voltmeter with low resistance, the voltage drop across the resistors becomes negligible. Consequently, the voltage values in the table tend to approach zero when the meter's resistance is much lower than the value of R.
Learn more about voltmeter here:
https://brainly.com/question/1511135
#SPJ11
A spring is initially compressed by 2.5 cm. If it takes 0.523 J of work to compress the spring an additional 3.2 cm, what is the spring constant of the spring?
The spring constant of the spring is 70.9 N/m.
Here's how to solve this problem step by step:
Let's suppose that k is the spring constant of the spring, x is the displacement of the spring from its equilibrium position, and W is the work done in compressing the spring.
We can use the formula W = (1/2)kx² to solve the problem.Here's how:
Step 1: Determine the work done in compressing the spring from 2.5 cm to (2.5 + 3.2) cm = 5.7 cm. Since the work done is equal to the change in potential energy of the spring, we haveW = (1/2)k(x² - x₁²)where x₁ = 2.5 cm, and x = 5.7 cm.
Substituting these values, we getW = (1/2)k((5.7 cm)² - (2.5 cm)²)W = (1/2)k(32.84 cm²)W = 16.42 k N/cm.Note that we converted centimeters to newtons by multiplying by k.
Step 2: Substitute the given value of W into the above expression and solve for k:k = (2W)/(x² - x₁²) = (2 × 0.523 J)/(5.7² - 2.5²) cm = 70.9 N/m.
Therefore, the spring constant of the spring is 70.9 N/m.
Learn more about equilibrium here,
https://brainly.com/question/517289
#SPJ11
A conductor sphere (radius R) is kept at a constant potential Vo. A point charge Q is located at d from the center of the sphere. Calculate the potential of the space and the total charge on the sphere. (15 marks)
The potential of the space outside the conductor sphere is Vo. The total charge on the sphere is -Q, equal in magnitude but opposite in sign to the point charge Q.
In physics, magnitude refers to the size or quantity of a physical property or phenomenon, typically represented by a numerical value and a unit of measurement. Magnitude can describe various aspects, such as the magnitude of a force, the magnitude of an electric field, the magnitude of a velocity, or the magnitude of an acceleration. It is a fundamental concept in physics that helps quantify and compare different physical quantities, enabling scientists to analyze and understand the behavior of natural phenomena.
Learn more about magnitude here:
https://brainly.com/question/30015989
#SPJ11
An object with initial momentum 6 kg: m/s to the left is acted upon by a force F = 48 N to the right for a short time interval, At. At the end of this time interval, the momentum of the object is 2 kg · m/s to the right. How long was the time interval, At ? 2/3 s 1/12 s 1/2 s 1/3 s 1/24 s 1/6 s 1/4 s
The time interval is given in seconds, therefore, the time interval for which force is applied, At is 1/2 s. The correct option for the given question is c. 1/2 s.
Here is the explanation:
Given data,
Initial momentum, p₁ = -6 kg m/s
Force applied, F = 48 N
Final momentum, p₂ = 2 kg m/s
The time interval for which the force is applied is At. The momentum of an object is given as:
p = mv
Where, p = momentum, m = mass, v = velocity
Initially, the object is moving towards the left, therefore, the velocity is negative. And, finally, the object is moving towards the right, therefore, the velocity is positive.
Initially, momentum is given as:
p₁ = -6 kg m/s
Using the law of conservation of momentum;
p₁ = p₂
⇒ -6 = 2m
⇒ m = -6/2 = -3 kg
Therefore, mass is equal to 3 kg.
Initially, the velocity of the object is given by:
p₁ = -6 = -3 v₁
⇒ v₁ = 2 m/s
The force applied can be found out using the following formula:
F = Δp/Δt
Where, Δp = Change in momentum = p₂ - p₁ = 2 - (-6) = 8 kg m/s
F = 48 N
Δt = F/Δp = 48/8 = 6 s
But, the time interval is given in seconds, therefore, the time interval for which force is applied, At is:
At = Δt/2 = 6/2 = 3 s. Answer: 1/2 s.
To learn more about Initial momentum refer:-
https://brainly.com/question/12450698
#SPJ11
The boiling point of helium at one atmosphere is 4.2 K.What is the volume occupied by the helium gass due to the evaporation of 10 g of liquid helium at 1 atm of pressure for the following temperatures a) 4.2 K b) 293 K A cubic metal box with sides of 20 cm contains air at a pressure of 1 atm and a temperature of 300 K. The box is sealed so that the volume is constant, and it is heated to a temperature of 400 K. Find the net force on each wall of the box.
2.5 mol of helium occupies a volume of 22.4 L × 2.5 = 56 L. The volume of the helium gas is approximately 61.3 L. The net force on each wall of the box is approximately 2355 N.
a) The boiling point of helium at one atmosphere is 4.2 K. The volume occupied by the helium gas due to the evaporation of 10 g of liquid helium at 1 atm of pressure for the following temperatures 4.2 K can be calculated as follows:
Mass of liquid helium, m = 10 g
Molar mass of helium, M = 4 g mol^(-1)
Number of moles, n = (10 g) / (4 g mol^(-1)) = 2.5 mol
Since 1 mol of an ideal gas at standard temperature and pressure occupies a volume of 22.4 L, therefore 2.5 mol of helium occupies a volume of 22.4 L × 2.5 = 56 L.
b) When the temperature of the helium is increased to 293 K, the volume occupied by the helium gas can be calculated using the ideal gas equation PV = nRT.
P = 1 atm
V = ?
n = 2.5 mol
R = 8.314 J mol^(-1) K^(-1)
T = 293 K
Therefore, V = (nRT) / P = (2.5 mol × 8.314 J mol^(-1) K^(-1) × 293 K) / (1 atm) ≈ 61.3 L
The volume of the helium gas is approximately 61.3 L. Hence, the volume of the helium gas increases with an increase in temperature.
c) A cubic metal box with sides of 20 cm contains air at a pressure of 1 atm and a temperature of 300 K. The box is sealed so that the volume is constant, and it is heated to a temperature of 400 K. The net force on each wall of the box can be calculated as follows:
Initial pressure, P1 = 1 atm
Initial temperature, T1 = 300 K
Final temperature, T2 = 400 K
Volume, V = (20 cm)^3 = (0.2 m)^3 = 0.008 m^3
The final pressure, P2, can be calculated using the ideal gas equation:
P1V1 / T1 = P2V2 / T2
P2 = P1V1T2 / V2T1
P2 = (1 atm × 0.008 m^3 × 400 K) / (0.008 m^3 × 300 K) ≈ 1.33 atm
The change in pressure, ΔP, can be calculated using the equation:
ΔP = P2 − P1
ΔP = 1.33 atm − 1 atm = 0.33 atm
The net force on each wall of the box can be calculated using the equation:
Fnet = PΔA
= ΔPΔA
= ΔP × (2lw + 2lh + 2wh)
where l, w, and h are the length, width, and height of the box, respectively. Since the box is cubic, l = w = h = 20 cm = 0.2 m, therefore,
Fnet = ΔP × (2lw + 2lh + 2wh)
= (0.33 atm × 101325 Pa/atm) × (2 × 0.2 m × 0.2 m + 2 × 0.2 m × 0.2 m + 2 × 0.2 m × 0.2 m)
≈ 2355 N
The net force on each wall of the box is approximately 2355 N.
Learn more about boiling point: https://brainly.com/question/40140
#SPJ11
A gas in a container has heat added but the temperature decreases. Which one of the following is true during this process?
A. Positive work is done by the gas on the environment.
B. This process is not possible.
C. The internal energy will increase.
D. This work done by the gas is equal to the change in the internal energy of the gas.
E. The change in internal energy of the gas is equal to the heat added to the gas.
In this case, since the temperature is decreasing (indicating a decrease in internal energy) and heat is being added to the gas, the change in internal energy (ΔU) is equal to the heat added (Q). Therefore, option E: The change in internal energy of the gas is equal to the heat added to the gas is the correct statement.
When heat is added to a gas and the temperature decreases, it means that the gas is undergoing a process known as cooling or heat transfer out of the system. In this process, the gas releases internal energy in the form of heat to the surroundings. The decrease in temperature indicates a decrease in the average kinetic energy of the gas particles, resulting in a decrease in the internal energy of the gas.
According to the first law of thermodynamics, the change in internal energy of a system is equal to the heat added to the system minus the work done by the system:
ΔU = Q - W
To know more about first law of thermodynamics
https://brainly.com/question/32101564
#SPJ11
A horizontal power line carries a current of 4230 A from south to north. Earth's magnetic field (76.0μT) is directed toward the north and is inclined downward at 59.0° to the horizontal. Find the (a) magnitude and (b) direction of the magnetic force on 100 m of the line due to Earth's field.
(a) Number ___________ Units ________
(b) ______
Magnitude of the magnetic force due to Earth's field is 320 N and the direction of the magnetic force is westward.
The magnetic force (F) on a current-carrying wire of length l, carrying a current I in a magnetic field of strength B, can be expressed as:
F = B I l sin θ
where θ is the angle between the direction of the magnetic field and the wire.
θ = 59° (in the downward direction)
B = 76.0 μT = 76.0 × 10⁻⁶ TB = 76.0 × 10⁻⁶ TI = 4230 Al = 100 m
(a) Magnitude of the magnetic force:
F = B I l sin θ= (76.0 × 10⁻⁶) × (4230) × (100) × sin 59.0°= 320 N
Therefore, the magnitude of the magnetic force due to Earth's field is 320 N.
(b) Direction of the magnetic force:
As the magnetic field is directed toward the north and the current flows from south to north, the direction of the magnetic force can be determined using the right-hand rule. Place your right hand such that the thumb points towards the direction of the current, the fingers point towards the direction of the magnetic field, and the palm points towards the direction of the magnetic force. Therefore, the direction of the magnetic force is westward.
Therefore, the magnitude of the magnetic force is 320 N and the direction of the magnetic force is westward.
Learn more about magnetic force https://brainly.com/question/2279150
#SPJ11
&=8.854x10-¹2 [F/m] lo=4r×107 [H/m] 12) A distortionless transmission line has an attenuation constant of 1.00×10³ Np/m. The line parameters are L = 5μH/m and R=1.092/m. From the information provided, we may conclude that the phase velocity (in m/s) along the line equals: a) 2x108 b) 108 c) 5x107 d) 1.5x108 e) None of the above. 13) The electric field of a TEM plane wave propagating in air has is given by E = 10a cos(at-3x - 4y) [V/m]. The angular frequency [rad/s] of the wave equals: a) 1×10⁹ b) 3x10⁹ c) 1.5×10⁹ d) 3.5×10⁹ e) 0.9×10⁰
The angular frequency of the wave equals 3x10⁹ rad/s. Hence, the correct option is b) 3x10⁹.
Given, Electric field of a TEM plane wave propagating in air is
E = 10a cos(at-3x - 4y) [V/m].
Here, the expression for an electromagnetic wave is of the form:
cos(wt - kz + phi)
where, w = angular frequency,
k = w/c = wave number, and
phi = phase constant.
So, the given expression of the electric field has to be reduced to this form.
First, compare the given expression with the general equation:
cos(wt - kz + phi)
Here,
w = angular frequency
k = 3/c = 3x10⁹/3x10⁸ = 10 rad/ms= 10x10⁶ rad/sw = 3x10⁹ rad/s
Comparing the coefficients of cos in the two expressions, we get:
w = 3x10⁹ rad/s
Hence, the correct option is b) 3x10⁹.
learn more about angular frequency here:
https://brainly.com/question/30897061
#SPJ11
Three two-port eircuits, namely Circuit 1 , Circuit 2 , and Circuit 3 , are interconnected in cascade. The input port of Circuit 1 is driven by a 6 A de current source in parallel with an internal resistance of 30Ω. The output port of Circuit 3 drives an adjustable load impedance ZL The corresponding parameters for Circuit 1, Cireuit 2 , and Circuit 3 , are as follows. Circuit 1: G=[0.167S0.5−0.51.25Ω] Circuit 2: Y=[200×10−6−800×10−640×10−640×10−6]S Circuit 3: Z=[33534000−3100310000]Ω a) Find the a-parameters of the eascaded network. (20 marks) b) Find ZL such that maximum power is transferred from the cascaded network to ZL. (10 marks) c) Evaluate the maximum power that the cascaded two-port network can deliver to ZL.
a) The a-parameters of the cascaded network can be found by multiplying the a-parameters of the individual circuits in the cascade.
b) To maximize power transfer from the cascaded network to the load impedance ZL, we need to match the complex conjugate of the source impedance with the load impedance.
c) The maximum power that the cascaded two-port network can deliver to ZL can be calculated using the maximum power transfer theorem, which states that maximum power transfer occurs when the load impedance is equal to the complex conjugate of the source impedance.
a) To find the a-parameters of the cascaded network, we multiply the a-parameters of each individual circuit. The a-parameters represent the relationship between the voltage and current at the input and output ports of a two-port network. Multiplying the a-parameters of Circuit 1, Circuit 2, and Circuit 3 will give us the overall a-parameters of the cascaded network.
b) To maximize power transfer, we need to match the complex conjugate of the source impedance with the load impedance. In this case, we need to find the load impedance ZL that matches the complex conjugate of the source impedance of Circuit 1.
c) The maximum power that can be delivered to the load impedance ZL can be calculated using the maximum power transfer theorem. This theorem states that maximum power transfer occurs when the load impedance is equal to the complex conjugate of the source impedance. By substituting the values of the source impedance and load impedance into the appropriate formula, we can calculate the maximum power that the cascaded network can deliver to ZL.
To know more about cascade click here:
https://brainly.com/question/17760981
#SPJ11
A 5.0-cm diameter, 10.0-cm long solenoid that has 5000 turns of wire is used as an inductor. The maximum allowable potential difference across the inductor is 200 V. You need to raise the current through the inductor from 1.0 A to 5.0 A. What is the minimum time you should allow for changing the current? 98.8 ms 49.4 ms 36.7 ms 25.8 ms 12.3 ms 62 ms
The minimum time required to change the current through the inductor from 1.0 A to 5.0 A is approximately 49.4 ms.
The minimum time required to change the current through the inductor can be calculated using the formula:
Δt = L × ΔI / V
Given:
Diameter of the solenoid = 5.0 cm
Radius of the solenoid = 5.0 cm / 2 = 2.5 cm = 0.025 m
Length of the solenoid = 10.0 cm = 0.1 m
Number of turns = 5000
Current change = 5.0 A - 1.0 A = 4.0 A
Maximum potential difference = 200 V
First, we need to calculate the inductance of the solenoid using the formula:
L = (μ₀ × N² × A) / l
Where:
μ₀ is the permeability of free space (4π × [tex]10^{-7}[/tex] T·m/A)
N is the number of turns
A is the cross-sectional area of the solenoid
l is the length of the solenoid
Calculating the cross-sectional area:
A = π × r² = π × (0.025 m)²
Calculating the inductance:
L = (4π × [tex]10^{-7}[/tex] T·m/A) × (5000²) × (π × (0.025 m)²) / (0.1 m)
Next, we can substitute the values into the formula for the minimum time:
Δt = L × ΔI / V
Calculating Δt:
Δt = L × (4.0 A) / (200 V)
Now we can substitute the calculated values and solve for Δt:
Δt = (calculated value of L) × (4.0 A) / (200 V)
After performing the calculations, the result is approximately 49.4 ms.
Therefore, the minimum time required to change the current through the inductor from 1.0 A to 5.0 A is approximately 49.4 ms.
Learn more about inductance here:
https://brainly.com/question/29981117
#SPJ11
A disabled tanker leaks kerosene (n = 1.20) into the Persian Gulf, creating a large slick on top of the water (n = 1.30). (a) If you are looking straight down from an airplane, while the Sun is overhead, at a region of the slick where its thickness is 460 nm, for which wavelength(s) of visible light is the reflection brightest because of constructive interference? (b) If you are scuba diving directly under this same region of the slick, for which wave- length(s) of visible light is the transmitted intensity strongest?
The wavelength of the visible light that is reflected that is brightest due to constructive interference is 0.8 μm.
The wavelength(s) of visible light the transmitted intensity is strongest is red light (λ = 700 nm).
(a) The reflection is brightest due to constructive interference at a point on the slick where its thickness is equal to an odd multiple of half the wavelength of the reflected light. If t is the thickness of the slick at a particular point, the reflected waves from the top and bottom surfaces will interfere constructively if 2nt = (2n + 1)λ/2, where λ is the wavelength of the reflected light, and n is an integer. Since n = 1 for air and n = 1.30 for the kerosene slick, the thickness of the slick for maximum reflection of a wavelength of λ is given by:
2 × 1.30 × t = (2 × 1 + 1)λ/2 = (3/2)λt = (3λ/4) / 1.30 = 0.577λ.
In order for the reflected light to be brightest, the thickness of the slick must be equal to 460 nm = 0.46 μm. So we have,0.46 μm = 0.577λλ = 0.8 μm
The wavelength of the reflected light that is brightest due to constructive interference is 0.8 μm.
(b) The amount of light transmitted through the slick is given by the equation
I/I0 = [(n2 sin θ2)/(n1 sin θ1)]2
where I is the transmitted intensity, I0 is the incident intensity, n1 and n2 are the indices of refraction of the two media, and θ1 and θ2 are the angles of incidence and refraction, respectively. Since the angle of incidence and angle of refraction are the same for light that enters and exits a medium at normal incidence, the equation simplifies to
I/I0 = (n2/n1)2
The transmitted intensity will be strongest for the wavelength of light that is least absorbed by the kerosene. In the visible region of the spectrum, violet light (λ = 400 nm) is the most absorbed and red light (λ = 700 nm) is the least absorbed. Since the index of refraction of kerosene is greater than that of water, the transmitted intensity will be strongest for the wavelength of light with the highest index of refraction. The index of refraction of kerosene is 1.20, which is less than that of water (1.33).
Therefore, the transmitted intensity will be strongest for the wavelength of light with the longest wavelength that is least absorbed by the kerosene, which is red light (λ = 700 nm).
Hence, for the wavelength(s) of visible light the transmitted intensity is strongest is red light (λ = 700 nm).
Thus :
The wavelength of the visible light that is reflected that is brightest due to constructive interference is 0.8 μm.
The wavelength(s) of visible light the transmitted intensity is strongest is red light (λ = 700 nm).
Learn more about visible light https://brainly.com/question/1170314
#SPJ11
An object is thrown from the ground into the air with a velocity of 18.0 m/s at an angle of 30.0 ∘
to the horizontal. What is the masimum height reached by this object?
An object is thrown from the ground into the air with a velocity of 18.0 m/s at an angle of 30.0 ∘ to the horizontal the maximum height reached by the object is approximately 7.79 meters.
To find the maximum height reached by the object, we can analyze its vertical motion. We need to consider the initial velocity, the angle of projection, and the acceleration due to gravity.
Given:
Initial velocity (u) = 18.0 m/s
Angle of projection (θ) = 30.0°
First, we need to determine the vertical component of the initial velocity, which is given by Vy = u * sin(θ).
Vy = 18.0 m/s * sin(30.0°)
Vy = 9.0 m/s
Using this vertical component of velocity, we can find the time taken to reach the highest point using the equation Vy = u * sin(θ) - gt, where g is the acceleration due to gravity (approximately 9.8 m/s^2).
9.0 m/s = 18.0 m/s * sin(30.0°) - 9.8 m/s^2 * t
Solving for t, we find t ≈ 0.918 s.
Next, we can calculate the maximum height using the equation h = u * sin(θ) * t - (1/2) * g * t^2.
h = 18.0 m/s * sin(30.0°) * 0.918 s - (1/2) * 9.8 m/s^2 * (0.918 s)^2
h ≈ 7.79 m
Therefore, the maximum height reached by the object is approximately 7.79 meters. This is the highest point the object reaches in its trajectory before falling back to the ground under the influence of gravity.
Learn more about angle of projection here:
https://brainly.com/question/28789119
#SPJ11
Your tires have the recommended pressure of 35 psi (gauge) when the temperature is a comfortable 15.0◦C. During the night, the temperature drops to -5.0 ◦C. Assuming no air is added or removed, and assume that the tire volume remains constant, what is the new pressure in the tires?
The new pressure in the tires, after the temperature drops from 15.0°C to -5.0°C, therefore new pressure will be lower than the recommended 35 psi (gauge).
To calculate the new pressure in the tires, we can use the ideal gas law, which states that the pressure of a gas is directly proportional to its temperature and inversely proportional to its volume, assuming constant amount of gas. The equation for the ideal gas law is:
PV = nRT
Where:
P = pressure
V = volume
n = number of moles of gas (assumed constant)
R = ideal gas constant
T = temperature in Kelvin
First, let's convert the temperatures to Kelvin:
Initial temperature (T1) = 15.0°C + 273.15 = 288.15 K
Final temperature (T2) = -5.0°C + 273.15 = 268.15 K
Since the tire volume remains constant, we can assume V1 = V2.
Now, we can rearrange the ideal gas law equation to solve for the new pressure (P2):
P1/T1 = P2/T
Plugging in the values:
35 psi (gauge)/288.15 K = P2/268.15 K
Now we can solve for P2:
P2 = (35 psi (gauge)/288.15 K) * 268.15 K
Calculating this equation, we find that the new pressure in the tires after the temperature drop is approximately 32.77 psi (gauge). Therefore, the new pressure in the tires will be lower than the recommended 35 psi (gauge) due to the decrease in temperature.
Learn more about pressure here:
https://brainly.com/question/30482677
#SPJ11
An RL circuit is composed of a 12 V battery, a 6.0 Hinductor and a 0.050 Ohm resistor. The switch is closed at t=0 000 The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is zero. The time constant is 2.0 minutes and after the switch has been closed a long time the voltage across the inductor is 12 V. The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is 12V. The time constant is 2.0 minutes and after the switch has been closed a long time the current is
the correct statements are: 1. The time constant of 1.2 minutes leads to zero voltage across the inductor after a long time. 2. The time constant of 2.0 minutes leads to a steady-state current after a long time.
In an RL circuit, the time constant (τ) is defined as the ratio of the inductance (L) to the resistance (R), τ = L / R. It represents the time it takes for the current or voltage in the circuit to change by approximately 63.2% of its final value.
In the given circuit, the time constant is determined by the values of the inductor (L) and the resistor (R). The time constant of 1.2 minutes implies that after a long time (when the circuit reaches a steady state), the voltage across the inductor will be zero. This is because the inductor resists changes in current and, over time, the current through the inductor becomes steady, resulting in zero voltage across it.
On the other hand, the time constant of 2.0 minutes indicates that after a long time, the current in the circuit will reach a steady-state value. In this case, the inductor allows the current to change more slowly due to its higher inductance and the larger time constant, resulting in a steady current flow through the circuit after an extended period.
Learn more about inductor here:
https://brainly.com/question/31503384
#SPJ11
A long cylinder (radius =3.0 cm ) is filled with a nonconducting material which carries a uniform charge density of 1.3μC/m 3
. Determine the electric flux through a spherical surface (radius =2.5 cm ) which has a point on the axis of the cylinder as its center. 9.61Nm ∧
2/C 8.32 Nm n
2C 3.37×10×2Nmn2/C 737×10 ∧
2Nm×2C
The electric flux through the spherical surface, which has a point on the axis of the cylinder as its center, is 9.61 Nm²/C.
To determine the electric flux through the given spherical surface, we can make use of Gauss's law. Gauss's law states that the electric flux through a closed surface is equal to the enclosed charge divided by the permittivity of free space (ε₀).
First, let's find the charge enclosed within the spherical surface. The cylinder is filled with a nonconducting material that carries a uniform charge density of 1.3 μC/m³. The volume of the cylinder can be calculated using the formula for the volume of a cylinder: V = πr²h, where r is the radius and h is the height. Since the cylinder is long, we can consider it as an infinite cylinder.
The charge Q enclosed within the spherical surface can be calculated by multiplying the charge density (ρ) by the volume (V). So, Q = ρV.
Next, we can calculate the electric flux (Φ) through the spherical surface using the formula Φ = Q / ε₀.
To find ε₀, we can use its value, which is approximately 8.85 x 10⁻¹² Nm²/C.
By substituting the known values into the equation, we find that Φ = (ρV) / ε₀.
Substituting the values for ρ (1.3 μC/m³), V (volume of the cylinder), and ε₀, we can calculate the electric flux.
Finally, after performing the calculations, we find that the electric flux through the spherical surface is 9.61 Nm²/C.
Learn more about electric flux here:
https://brainly.com/question/14544020
#SPJ11
Consider a 3-body system their masses,m,,me & m, and their position vectors are, 11.12.&3. Write the equations of motions each object Attach File browie Lacal Files Browse Content Collection
In physics, three-body problems include computing the motion of three bodies interacting with each other under the effect of gravity. Consider a 3-body system where their masses, m, me, and m, and their position vectors are 11, 12, and 3. We can write the equations of motion for each object using Newton's second law of motion.
Newton's second law of motion can be written as:
F = ma Where F is the net force on an object, m is its mass, and a is its acceleration. For each object, we can write the equation of motion in terms of the components of the net force acting on it. For the first object with mass m1 and position vector r1, the net force acting on it is given by:
F1 = G(m2m1/|r2-r1|^2)(r2-r1) + G(m3m1/|r3-r1|^2)(r3-r1)
where G is the universal gravitational constant and |r2-r1| denotes the magnitude of the vector r2-r1.
The equation of motion for the first object can be written as:
m1a1 = G(m2m1/|r2-r1|^2)(r2-r1) + G(m3m1/|r3-r1|^2)(r3-r1)
where a1 is the acceleration of the first object.
Similarly, for the second object with mass m2 and position vector r2, the equation of motion can be written as:
m2a2 = G(m1m2/|r1-r2|^2)(r1-r2) + G(m3m2/|r3-r2|^2)(r3-r2)
where a2 is the acceleration of the second object.
For the third object with mass m3 and position vector r3, the equation of motion can be written as:
m3a3 = G(m1m3/|r1-r3|^2)(r1-r3) + G(m2m3/|r2-r3|^2)(r2-r3)
where a3 is the acceleration of the third object.
These are the equations of motion for each object in the 3-body system.
Learn more about Newton's second law of motion here
https://brainly.com/question/2009830
#SPJ11
Write the 4-momentum P = (5 , pc) of E a particle of mass m in terms of its V rapidity defined by ?
The 4-momentum of a particle E with mass m can be expressed as P = (5, pc) in terms of its rapidity V.
The 4-momentum of a particle is a four-component vector that describes its energy and momentum in the context of special relativity. It is denoted as P = (E, pc), where E is the energy of the particle and pc represents the momentum in the x, y, and z directions.
In terms of the rapidity V, which is defined as the hyperbolic tangent of the particle's velocity v, we can express the energy E as a function of the rapidity.
The relationship between rapidity and velocity is given by the equation,
V = tanh⁻¹(v), where v is the velocity of the particle.
Solving for v, we find v = tanh(V).
To obtain the 4-momentum in terms of rapidity, we first express the energy E in terms of the particle's rest mass m and its velocity v using the relativistic energy-momentum relationship:
E = γmc²,
where γ is the Lorentz factor γ = 1/√(1 - v²/c²).
Substituting v = tanh(V), we can rewrite γ as γ = cosh(V).
Finally, we obtain the 4-momentum as P = (E, pc) = (γmc², γmvc), where c is the speed of light.
Simplifying this expression, we have P = (5, mc sinh(V)c), where sinh(V) represents the hyperbolic sine of the rapidity V.
Therefore, the 4-momentum of the particle E in terms of its rapidity V is P = (5, pc) = (5, mc sinh(V)c), where mc represents the magnitude of the particle's momentum in the x, y, and z directions.
To learn more about Lorentz factor visit:
brainly.com/question/31962456
#SPJ11
which are cardiovascular drug classes? select all that apply
Cardiovascular drug classes are Beta-blockers, Diuretics, Calcium channel blockers, and ACE inhibitors. The correct answer is options are A, B, D, and F.
Cardiovascular drug classes refer to categories of medications specifically designed to treat conditions related to the cardiovascular system. These medications target various aspects of cardiovascular health, such as blood pressure regulation, heart rhythm management, and the prevention of clot formation. Several recognized cardiovascular drug classes include:A) Beta-blockers: These drugs block the effects of adrenaline on the heart and blood vessels, reducing heart rate and blood pressure.B) Diuretics: Also known as water pills, diuretics help eliminate excess fluid from the body, reducing fluid buildup and decreasing blood pressure.D) Calcium channel blockers: These medications relax and widen blood vessels, improving blood flow and reducing blood pressure. They also help regulate heart rate.F) ACE inhibitors: ACE (angiotensin-converting enzyme) inhibitors lower blood pressure by blocking the production of a hormone that narrows blood vessels.Therefore, the correct options for cardiovascular drug classes are A) Beta-blockers, B) Diuretics, D) Calcium channel blockers, and F) ACE inhibitors. These medications play crucial roles in managing cardiovascular conditions and promoting overall heart health.For more questions on the cardiovascular system
https://brainly.com/question/16948738
#SPJ8
The correct question would be as
Which of the following are cardiovascular drug classes? Select all that apply.
A) Beta-blockers
B) Diuretics
C) Antibiotics
D) Calcium channel blockers
E) Antidepressants
F) ACE inhibitors
For the circuit shown, what is the rate of change of the current in the inductor when: L=30mH,R =20ohm,V=12 volts, and the current in the battery is 0.3 A ? Write your answer as a magnitude, in A/s. Question 10 1 pts The switch in the figure is closed at t=0 when the current l is zero. When I=19 mA, what is the potential difference across the inductor, in volts?
a. The potential difference across the inductor is 6 volts when the current is 19 mA.
b. the rate of change of current in the inductor is zero (0 A/s) in this circuit configuration.
How do we calculate?The voltage across an inductor in an RL circuit is :
V = L di/dt,
we have:
L = 30 mH = 0.03 H
R = 20 Ω
V = 12 volts
Current in the battery = 0.3 A
Using Ohm's Law, we have:
V = I * R = 0.3 A * 20 Ω = 6 volts
The total voltage across the circuit is equal to the sum of the voltage across the resistor and the voltage across the inductor:
V(inductor) = V - V(resistor) = 12 volts - 6 volts = 6 volts
The potential difference across the inductor is 6 volts when the current is 19 mA.
The rate of change of current in the inductor is:
L = 30 mH = 0.03 H
R = 20 Ω
V = 12 volts
Current in the battery = 0.3 A
dV/dt =[tex]L d^2i/dt^2,[/tex]
0 = [tex]L d^2i/dt^2.[/tex]
[tex]d^2i/dt^2[/tex] = 0.
Learn more about current at:
https://brainly.com/question/1100341
#SPJ4
The change in enthalpy will always be negative under which conditions? A. The change in enthalpy actually can never be negative B. The internal energy increases and the volume increases C. The internal energy decreases and the volume increases D. The internal energy decreases and the volume decreases E. The internal energy increases and the volume decreases
Answer: The change in enthalpy will always be negative under which conditions is given by the option D.
The change in enthalpy will always be negative under the following conditions: The internal energy decreases and the volume decreases. The change in enthalpy will always be negative under which conditions is given by the option D.
The internal energy decreases and the volume decreases. Entropy is used to measure the energy that is not available to do work. In chemistry, changes in enthalpy are a measure of heat flow into or out of a system during chemical reactions or phase transitions such as melting or boiling.
Enthalpy (H) is defined as the sum of the internal energy (U) and the product of pressure (P) and volume (V).H = U + PVWhen enthalpy increases, a reaction or process absorbs heat from the surroundings. Conversely, when enthalpy decreases, a reaction or process releases heat into the surroundings.
Hence, The change in enthalpy will always be negative under the following conditions: The internal energy decreases and the volume decreases.
Learn more about internal energy: https://brainly.com/question/25748529
#SPJ11
Charges Q₁ = 4.32 μC and Q2 = 2.18 μC are separated by a distance r = 4 cm. What is the potential energy of the two charges? Show the SI units.
The potential energy between two charges, [tex]Q_1 = 4.32 \mu C[/tex] and [tex]Q_2 = 2.18 \mu C[/tex], separated by a distance of 4 cm is approximately 2.474 joules which are calculated by using the formula for electrical potential energy.
The potential energy between two charges can be determined using the formula:
[tex]U = (k * Q_1 * Q_2) / r[/tex]
where U represents the potential energy, [tex]Q_1[/tex] and [tex]Q_2[/tex] are the charges, r is the distance between the charges, and k is the electrostatic constant ([tex]k = 8.99 *10^9 Nm^2/C^2[/tex]).
In this case, [tex]Q_1= 4.32 \mu C[/tex] (microcoulombs) and [tex]Q_2 = 2.18 \mu C[/tex], and the distance r = 4 cm (or 0.04 m when converted to meters). Plugging these values into the formula, we can calculate the potential energy:
[tex]U = (8.99 * 10^9 Nm^2/C^2 * 4.32 * 10^-^6 C * 2.18 * 10^-^6 C) / 0.04 m\\U =2.474 J (joules)[/tex]
Therefore, the potential energy between the two charges is approximately 2.474 joules. The SI unit for potential energy is joules (J).
Learn more about potential energy here:
https://brainly.com/question/24284560
#SPJ11
Four identical charges (+1.8 μC each) are brought from infinity and fixed to a straight line. Each charge is 0.37 m from the next. Determine the electric potential energy of this group. Number Units
The value of the electric potential energy for the given group of charges is approximately 1.62 joules (J).
The electric potential energy U of a system of charges is given by the equation:
[tex]\[ U = \frac{1}{4\pi\epsilon_0} \sum_{i=1}^{n}\sum_{j > i}^{n} \frac{q_i q_j}{r_{ij}} \][/tex]
where [tex]\( \epsilon_0 \)[/tex] is the permittivity of free space, [tex]\( q_i \)[/tex] and [tex]\( q_j \)[/tex] are the charges, and [tex]\( r_{ij} \)[/tex] is the distance between charges i and j.
In this case, we have four identical charges of +1.8 μC each fixed in a straight line. The charges are equidistant from each other with a separation of 0.37 m. Substituting the given values into the equation, we can calculate the electric potential energy of the group.
[tex]\[ U = \frac{1}{4\pi\epsilon_0} \left(\frac{q_1 q_2}{r_{12}} + \frac{q_1 q_3}{r_{13}} + \frac{q_1 q_4}{r_{14}} + \frac{q_2 q_3}{r_{23}} + \frac{q_2 q_4}{r_{24}} + \frac{q_3 q_4}{r_{34}}\right) \][/tex]
Substituting[tex]\( q_i = 1.8 \times 10^{-6} \) C, \( r_{ij} = 0.37 \)[/tex]m, and [tex]\( \epsilon_0 = 8.85 \times 10^{-12} \) F/m[/tex], we can calculate the electric potential energy.
Evaluating this expression, the numerical value of the electric potential energy for the given group of charges is approximately 1.62 joules (J).
Learn more about potential energy here:
https://brainly.com/question/24284560
#SPJ11
A) How do the sources of electric fieids and magnetic fields differ? B) How does the nature of electric fields differ from the nature of magnetic fields?
A)The sources of electric fields and magnetic fields differ in their fundamental nature and origin. B)Electric fields are produced by electric charges, whether stationary or in motion, while magnetic fields are generated by moving charges or by the presence of a magnetic dipole.
Electric fields arise from the presence of electric charges. Stationary charges, such as electrons or protons, create static electric fields. These fields exert forces on other charges, attracting opposite charges and repelling similar charges. When charges are in motion, they generate both electric and magnetic fields. The motion of charges creates a changing electric field, which, in turn, generates a magnetic field. This phenomenon is described by Maxwell's equations, specifically by Ampere's law with Maxwell's addition.
On the other hand, magnetic fields have different sources. They are primarily produced by moving charges or currents. When charges move through a conductor, such as a wire, a magnetic field is generated around the conductor. Similarly, magnetic fields can arise from the presence of magnetic dipoles, which are materials with a north and south pole. Examples of magnetic dipoles include magnets and certain ferromagnetic materials.
The nature of electric fields and magnetic fields also differs. Electric fields are associated with the presence of electric charges and exert forces on other charges. They are radial in nature, meaning they emanate from a charge and decrease in strength with distance according to an inverse square law. Electric fields can exist even in the absence of motion.
On the other hand, magnetic fields are always associated with the motion of charges. They do not exert direct forces on charges at rest but act on moving charges or currents. Magnetic fields form closed loops around current-carrying conductors and follow certain rules, such as the right-hand rule, to determine their direction. Unlike electric fields, magnetic fields are not radial and do not diminish with distance in a simple inverse square relationship.
In summary, the sources of electric fields are electric charges, while magnetic fields originate from moving charges or the presence of magnetic dipoles. Electric fields are associated with charges and can exist even without motion, while magnetic fields are related to the motion of charges and form closed loops around current-carrying conductors. The nature of electric fields is radial and exerts forces on other charges, while magnetic fields act on moving charges and do not exert direct forces on charges at rest.
Learn more about electric fields and magnetic fields:
https://brainly.com/question/11482745
#SPJ11
A spherical shell of radius 1.59 cm and a sphere of radius 8.47 cm are rolling without slipping along the same floor: The two objects have the same mass. If they are to have the same total kinetic energy, what should the ratio of the spherical shell's angular speed ω s
to the sphere's angular speed ω sph
be?
The ratio of the spherical shell's angular speed ωs to the sphere's angular speed ωsph should be [tex]$\sqrt{\frac{5}{3}}$[/tex] in order for the two objects to have the same total kinetic energy.
Let us begin with the derivation of the solution to the given problem. Given conditions, a spherical shell of radius `r = 1.59 cm` and a sphere of radius `R = 8.47 cm` are rolling without slipping along the same floor. The two objects have the same mass and total kinetic energy. Let the common mass be `m`. The rotational kinetic energy of an object with the moment of inertia `I` and angular speed `ω` is given as:
[tex][tex]$\ K_r =\frac{1}{2}Iω^2$[/tex][/tex]
The moment of inertia of a uniform sphere of mass `m` and radius `R` is given as: [tex]$I_{sph} = \frac{2}{5}mR^2$[/tex]
The moment of inertia of a hollow sphere of mass `m` and radius `r` is given as:[tex]$I_{hollow\ shell} = \frac{2}{3}mR^2$[/tex]
For the two objects to have the same kinetic energy, we must have: [tex]$K_{sph} + K_{hollow\ shell} = K$[/tex]where `K` is the total kinetic energy of the two objects. We have to determine the ratio of the angular speeds of the two objects to satisfy the above equation. Let us begin by finding the kinetic energies of the two objects.
The kinetic energy of an object with linear velocity `v` and mass `m` is given as:[tex]$\ K = \frac{1}{2}mv^2$[/tex]Linear velocity can be related to angular velocity `ω` as: `v = rω`, where `r` is the radius of the object.
Therefore, the kinetic energies of the two objects can be expressed as:[tex]$K_{sph} = \frac{1}{2}mv_{sph}^2 = \frac{1}{2}m(r_{sph}ω_{sph})^2 = \frac{1}{2}mR^2ω_{sph}^2$$K_{hollow\ shell} = \frac{1}{2}mv_{hollow\ shell}^2 = \frac{1}{2}m(r_{hollow\ shell}ω_{hollow\ shell})^2 = \frac{1}{2}m(rω_{hollow\ shell})^2 = \frac{1}{2}m\left(\frac{2}{3}R\right)^2ω_{hollow\ shell}^2 = \frac{1}{9}mR^2ω_{hollow\ shell}^2$[/tex]
Substituting these expressions in the equation `K_sph + K_hollow shell = K` and solving for the ratio of the angular speeds, we get: [tex]$\frac{ω_{sph}}{ω_{hollow\ shell}} = \sqrt{\frac{5}{3}}$[/tex]
Hence, the ratio of the spherical shell's angular speed ωs to the sphere's angular speed ωsph should be[tex]$\sqrt{\frac{5}{3}}$[/tex] in order for the two objects to have the same total kinetic energy.
Learn more about angular speed here:
https://brainly.com/question/29058152
#SPJ11
A pendulum on the International Space Station the reaches a max speed of 1.24 m/s when reaches a maximum height of 8.80 cm above its lowest point. The local N/kg. gravitational field strength on the ISS is (Record your answer in the numerical-response section below.)
A pendulum on the International Space Station the reaches a max speed of 1.24 m/s when reaches a maximum height of 8.80 cm above its lowest point .Therefore, the local gravitational field strength on the ISS is 0.982 N/Kg
It is given that a pendulum on the International Space Station reaches a max speed of 1.24 m/s
when it reaches a maximum height of 8.80 cm above its lowest point.
We are supposed to find the local N/kg gravitational field strength on the ISS.
we will use the formula for potential energy and kinetic energy of a pendulum as follows:
Potential energy = mgh , Kinetic energy = 1/2 mv²
where m is the mass of the pendulum, g is the gravitational field strength, h is the maximum height and v is the maximum speed.
We will equate these two energies to get the value of g.1/2 mv² = mghv² = 2ghv² = 2 x 9.81 x 0.088v² = 0.17352v = 0.4168 m/s
Now, we have the value of maximum speed of the pendulum.
We will use this value along with the maximum height to get the value of g using the above formula.
1/2 mv² = mgh1/2 x 1 x (0.4168)² = 1 x g x 0.0880.08656 = g x 0.088g = 0.982 N/kg
Therefore, the local N/kg gravitational field strength on the ISS is 0.982 N/kg.
Learn more about gravitational field here:
https://brainly.com/question/31829401
#SPJ11
In a period of 5.00 s, 5.00 x 1023 nitrogen molecules strike a wall of area 7.40 cm². Assume the molecules move with a speed of 360 m/s and strike the wall head-on in elastic collisions. What is the pressure exerted on the wall? Note: The mass of one N, molecule is 4.65 x 10-26 kg.
The pressure exerted on the wall by 5.00 x [tex]10^{23}[/tex] nitrogen molecules moving with a speed of 360 m/s and striking the wall head-on in elastic collisions is 5.42 x 10⁶ Pa (pascals).
To calculate the pressure, we can use the formula:
pressure = force/area.
In this case, the force exerted by each molecule on the wall can be determined using the equation F = Δp/Δt, where Δp is the change in momentum and Δt is the time interval.
Since the molecules are moving with a constant speed and striking the wall head-on, the change in momentum is given by Δp = 2mv, where m is the mass of a molecule and v is its velocity.
Therefore, the force exerted by each molecule is 2mv/Δt.
Next, we need to determine the total force exerted by all the molecules. The total number of molecules is given as 5.00 x [tex]10^{23}[/tex], and the time interval is 5.00 s.
Thus, the total force is (2mv/Δt) * (5.00 x [tex]10^{23}[/tex]).
Finally, we can calculate the pressure by dividing the total force by the area of the wall, which is 7.40 cm². To convert the area to square meters, we divide by 10000. The resulting pressure is 5.42 x 10⁶ Pa.
To learn more about force exerted visit:
brainly.com/question/32203291
#SPJ11
In the diffusional transformation of solids, there are two major classes of ordering transformations; first-order and second-order transformations.
A) What are these? Explain them one by one.
B) Give examples for each one of the ordering transformations.
A) First-order transformations: First-order transformations involve a discontinuous change in the crystal structure of a material. In these transformations, there is a significant rearrangement of the atoms or molecules, resulting in a distinct change in the crystal symmetry and arrangement.
The transition from one crystal structure to another occurs abruptly, with a clear boundary between the two phases.
Second-order transformations: Second-order transformations, also known as displacive transformations or martensitic transformations, involve a continuous change in the crystal structure of a material. In these transformations, there is a distortion of the crystal lattice without any diffusion or rearrangement of atoms. The atoms maintain their relative positions, but the overall crystal structure undergoes a change in shape or orientation.
B) Examples of first-order transformations:
Phase transitions such as the transformation of graphite to diamond, where the carbon atoms rearrange from a layered structure to a three-dimensional network.
Allotropic transformations, such as the transition from austenite to martensite in steel, where the crystal structure changes from a face-centered cubic (FCC) to a body-centered tetragonal (BCT) structure.
Polymorphic transformations, such as the transition from the alpha form to the beta form of quartz.
Examples of second-order transformations:
Martensitic transformations in shape memory alloys, such as the transformation from the parent phase (austenite) to the martensite phase upon cooling or applying stress. This transformation involves a change in crystal structure without diffusion.
Ferroelastic transformations, where the crystal lattice undergoes a reversible distortion under the influence of an external stimulus like temperature or pressure.
Twinning transformations, where a crystal structure undergoes a deformation resulting in the formation of twin domains with a specific orientation relationship.
These examples illustrate the different mechanisms and characteristics of first-order and second-order transformations in the diffusional transformation of solids.
To know ore about atoms
https://brainly.com/question/1566330
#SPJ11
One end of a cord is fixed and a small 0.550-kg object is attached to the other end, where it swings in a section of a vertical circle of radius 1.00 m, as shown in the figure below. When © = 26.0°, the speed of the
object is 7.00 m/s.
One end of a cord is fixed and a small 0.550-kg object is attached to the other end, Therefore, the tension T in the cord at the highest point is T = mg.
When the object is at angle c = 26°, the speed of the object is 7 m/s. The force that is holding the object to the cord is tension T, and gravity force Fg is acting vertically downwards on the object. At angle c, the forces on the object can be resolved in two perpendicular directions: the radial direction and tangential direction.
Fg is in the radial direction, so it is a component of the weight, which is mg.sin(c) and pointing down.
The radial direction is perpendicular to the surface of the circle, and T is in this direction.
Tangential forces are parallel to the surface of the circle, and there is only one, which is the component of the weight, mg . cos(c) and is pointing tangentially to the circle surface. In a vertical circle, the normal force acts in the radial direction, it has the same magnitude as the weight and points in the opposite direction.
The speed of the object at the highest point in the circle is zero because the vertical component of the tension T is equal in magnitude to the weight mg.
Therefore, the tension T in the cord at the highest point is T = mg.
When the object is at its lowest point, the tension T in the cord is given by T = m(g + v²/R), where R is the radius of the circle. The force is the resultant of weight and the centrifugal force.
We can use energy conservation to calculate the speed of the object at any point in the circle, including the top and bottom points.
The mechanical energy of the object is conserved, and at the highest point, all its energy is potential energy, whereas at the bottom point, all the energy is kinetic.
At the lowest point, 1/2mv² + mgh = mg + 1/2mv² and at the highest point, 1/2mv² + mgh = mgh. Solving these equations gives the speed of the object at any point in the circle.
Learn more about potential energy here:
https://brainly.com/question/24284560
#SPJ11
A spring with a ball attached to one end is stretched and released. It begins simple harmonic motion, oscillating with a period of 1.2 seconds. If k-W newtons per meter is its spring constant, then what is the mass of ball? Show your work and give your answer in kilograms. W = 13 Nim
The spring-mass system executes simple harmonic motion when the net force F on it is proportional to the displacement x of its mass from the equilibrium position,
i.e., F = −kx, where k is the spring constant.
Using this expression for F in Newton’s second law, the equation of motion of the mass m can be obtained as follows:
ma = −kx
where a is the acceleration of the mass along the direction of motion. We can rewrite this equation as follows:
a = −(k/m) x
This is an equation of SHM whose solution is x = A cos (ωt + φ), where
A is the amplitude of the oscillation,
ω = √(k/m) is the angular frequency of the oscillation and
φ is the phase angle which is zero at t = 0.
The time period T of the SHM can be calculated as follows:
T = 2π/ω
= 2π √(m/k)
We are given T = 1.2 s, and k = W = 13 N/m.
Hence,T = 2π √(m/k)1.2
= 2π √(m/13)
Squaring both sides, we get
1.44 = 4π² (m/13)
So,
m = (1.44 × 13) / (4π²)≈ 0.0898 kg
Therefore, the mass of the ball is approximately 0.0898 kg which can be rounded to three significant figures as 0.090 kg or 90 grams.
Learn more about equilibrium position, here
https://brainly.com/question/517289
#SPJ11
Order the following shapes from greatest to least moment of inertia relative to the X-axis. _____ Hollow rectangle with base of 3.00" and height of 4.50" and a wall thickness of 0.250". ______ Hollow circle 4.50" outside diameter and 0.250" thick wall. ______ Solid circle 4.50" in diameter ______ W4X13 _____ Solid rectangle with base of 3.00" and height 4.50" ______ Solid triangle with base of 3.00" and height of 4.50"
Moment of inertia: The moment of inertia is a physical quantity that describes an object's resistance to rotational motion when a torque is applied to it. In the given question, triangle has the least moment of inertia.
Moment of inertia is directly proportional to the width and height of a given shape or structure. The W4X13 has a higher moment of inertia because of its wide flanges. The hollow rectangular structure has a moment of inertia that is only slightly smaller than the W4X13 since it has two sets of flanges. The next shape, a solid rectangle, has a slightly lower moment of inertia than a hollow rectangle, since it has no flanges. A solid circle has the same moment of inertia as a hollow circle since they have the same thickness. Finally, the triangle has the least moment of inertia, as it is the least structurally sound of all the shapes.
Learn more about moment of inertia:
https://brainly.com/question/14460640
#SPJ11