(a)
11001.1011₂ = 1×2⁴ + 1×2³ + 1×2⁰ + 1×2 ⁻¹ + 1×2 ⁻³ + 1×2 ⁻⁴
… = 16 + 8 + 1 + 1/2 + 1/8 + 1/16
… = 411/16
(b) In base 16, we have A₁₆ = 10 and C₁₆ = 12, so
A3.C₁₆ = 10×16¹ + 3×16⁰ + 12×16 ⁻¹
… = 160 + 3 + 12/16
… = 2620/16 = 655/4
(c)
75.16₈ = 7×8¹ + 5×8⁰ + 1×8 ⁻¹ + 6×8 ⁻²
… = 56 + 5 + 1/8 + 6/64
… = 3918/64 = 1959/32
(d) B₁₆ = 11 and D₁₆ = 13, so
ABCD₁₆ = 10×16³ + 11×16² + 12×16¹ + 13×16⁰
… = 40960 + 2816 + 192 + 13
… = 43981
WILL GIVE BRAINLEY PLZZZZZZZ
how is a electrical resistance similar to the diameter of a pipe of water
Answer:
The resistance of the flow of charges in an electric circuit (electrical resistance) is analogous to the frictional effect between water flow through a pipe and the pipe's surface
Explanation:
In comparison to its similarity to the diameter of the pipe affects the flow of water and acts a a factor affecting resistance so are there factors affecting electrical resistance.
in an electrical circuit:
the total length of the wire is to the length of a pipe of water
the cross-sectional area of the wire is to the diameter of a pipe of water.
Thus, the cross sectional are affects the amount of electrical resistance. Wider wires have wider cross-sectional area and vice versa. Also, water will flow (i.e. current) through a wider pipe (i.e. large diameter) at a faster rate than a narrow pipe (i.e. small diameter). This is due to the lower amount of resistance offered by the wider pipe.
in the same manner, the wider the wire, the lesser the electrical resistance to the flow of elsctric charge and vice versa for thiner wires.
B Urine
C Brass
D Sand
8. Separation of mixtures of solids with various sizes
include
A magnetic separation.
B coarsing
sublimation.
Air
Answer:
B
Explanation:
A pin B and D are each of 8mm diameter and act as single shape pin C is 6mm diameter and act as double shape for the laoding shaw determine averege shear stress in each
Answer:
what's the question?...........
How does Brake system work
Answer:
To stop a car, the brakes have to get rid of that kinetic energy. They do so by using the force of friction to convert that kinetic energy into heat. This hydraulic system multiplies the force of your foot on the brake pedal into enough force to apply the brakes and make the car stop.
Match the term to the best description scientific method
Answer:
a method of research in which a problem is identified, relevant data are gathered, a hypothesis is formulated from these data, and the hypothesis is empirically tested.
1. __________ is an example of an electrical device.
Answer:
1. Battery
2. Light bulb
3. Toaster
Explanation:
An electrical device is a device that produces or is powered by electricity.
Answer:
All of the above
Explanation:
Radio capacity may be increased in cellular concept by
Answer:
Answer is "Increasing the number of base stations & reusing the channels"
Explanation:
Answer:
radio capacity may be increased in cellular concept by increasing the number of base stations and reusing the channels.
A chemical rocket is used for launch into earth orbit. The combustion stagnation temperature is 3000K. The molecular weight of the combustion products is 26. The gases expand isentropically as an ideal gas mixture with specific-heat ratio of 1.2. The area ratio Ae/A* of the nozzle is 20, and the throat diameter is 0.1m. Determine:
a. The stagnation pressure if the expansion is correct at sea level
b. The rocket thrust at sea level, 15- km, 30km, and 60km altitude.
tìm phản lực gối tựa
Answer:
jwjehevrvbdbejd HB dbnwjsishrb t bxjwbkozkwnwn shxvbebhgvevhehjhr. jebn
What are the factors that influence the power input to the compressor?
a) The mass flow of air
b) The pressure ratio of the compressor
c) The inlet temperature
d) Temperature difference between the inlet and outlet
e) The properties of the working medium
Answer:
option e is correct answer
In a pipe of diameter 350mm and length 75mm, water is flowing at a velocity of 2.8m/s. If the Kinematic viscosity of water is 0.012 Stokes, calculate the Reynolds number,Evaluate the coefficient of friction
Explanation:
the answer is in picture
The electrical contractor association is typical example of a
Answer:
Trade association.
Explanation:
I'm thinking it is as it represents contractors who design, install, inspect and maintain amongst other activities electrical and electronic equipments or service.
in the metric system what is the prefix for 1000
Cho động cơ có Z=24 rãnh, 2p=4 cực. Vẽ sơ đồ khai triển dây quấn động cơ kiểu đồng tâm hai mặt phẳng, q tập trung, đầu vào các pha liên tiếp lệch 1200 điện.
Answer:
can u write it in English
Explanation:
can't understand it
the impact of engineering to socio economic development of the country
Which of the following policy actions could the federal reserve use to combat inflation
[tex] \huge{ \underbrace{ \overbrace{OPTIONS}}}[/tex]
[tex] \huge{ \underbrace{ \overbrace{PlEASE}}}[/tex]
A double-threaded Acme stub screw of known major diameter is used in ajack having a plain thrust collar of known mean diameter. Coefficients of running friction are estimated as 0.10 for the collar and 0.11 for the screw. Assume (1) the starting friction is about 1/3 higher than running friction and (2) the screw is not exposed to vibration.
Required:
a. Determine the pitch, lead, thread depth, mean pitch diameter, and helix angle of the screw.
b. Estimate the starting torque for raising and for lowering a 5000 lb load.
c. If the screw is lifting a 5000 lb load at the rate of 4 ft/min, what is the screw rpm? What is the efficiency of the jack under this steady-state condition?
d. Would the screw overhaul if a ball thrust bearing (of negligible friction) were used in place of the plain thrust collar.
Answer:
I'm pretty sure it's c but i may be wrong
a steel container expands in volume 1% when the pressure within it is increased by 70mpa at standard presssure
Answer:
mooji udaanaamii!!!
Explanation:
Propose any improvements if there are any in brake system
Improvements to brake systems are
Increase in disc radiusIncrease in caliper piston areaLine pressureThe friction coefficient between the pad and the rotorWhat is a brake system?Converts the thermal energy through friction, and the brake system takes the kinetic energy of your moving vehicle.Larger discs will permit for more brake torque as the brake pad will apply pressure at a larger radius, permitting for a higher moment.Increasing the size of the pistons means you have more area to put in a specific pressure. If the pressure remains the same and the area increases, the force applied will be increased.Push your foot harder, and the car brakes harder due to this the line pressure increases. Self-explanatory, but if you can increase the friction between the pad and the rotor, you can increase the braking torque.To learn more about the brake system refer to:
https://brainly.com/question/24408495
#SPJ