the heat of vaporization of acetone is ≈ 45.1 kJ/mol by using formula of
ΔHvap = q / n and q = m × ΔT × Cp.
To calculate the heat of vaporization (ΔHvap) of acetone (CH3COCH3) using the given data, we can use the equation:
ΔHvap = q / n
where q is the heat absorbed or released during the phase change (condensation in this case), and n is the number of moles of acetone.
To find q, we can use the equation:
q = m × ΔT × Cs
where m is the mass of acetone, ΔT is the change in temperature, and Cs is the specific heat capacity of acetone.
First, we need to find the moles of acetone:
moles = mass / molar mass
The molar mass of acetone (CH3COCH3) is calculated as follows:
(1 × 12.01 g/mol) + (3 × 1.01 g/mol) + (1 × 16.00 g/mol) = 58.08 g/mol
Now, let's calculate the moles of acetone for each temperature:
For 9.092°C:
moles1 = 35.66 g / 58.08 g/mol
For 29.27°C:
moles2 = 82.67 g / 58.08 g/mol
Next, we need to calculate the change in temperature:
ΔT = final temperature - initial temperature
ΔT = 29.27°C - 9.092°C
Now, we can calculate q:
q1 = (mass1) × (ΔT) × (Cs)
q2 = (mass2) × (ΔT) × (Cs)
Lastly, we can calculate the heat of vaporization (ΔHvap) using the equation:
ΔHvap = (q1 + q2) / (moles1 + moles2)
Cp = (2.22 J/(g·°C)) / (58.08 g/mol) ≈ 0.0382 J/(mol·°C)
Using the given temperatures:
ΔT = Temperature 2 - Temperature 1
ΔT = 29.27 °C - 9.092 °C ≈ 20.18 °C
Now we can calculate the heat absorbed or released (q):
q = m × ΔT × Cp
q = 47.01 g × 20.18 °C × 0.0382 J/(mol·°C)
q ≈ 36.53 J
Finally, we can calculate the heat of vaporization (ΔHvap):
ΔHvap = q / n
ΔHvap = 36.53 J / 0.810 mol
ΔHvap ≈ 45.1 kJ/mol
Make sure to substitute the values into the equations and perform the calculations to find the heat of vaporization of acetone in kJ/mol.
To know more about heat of vaporization Visit:
https://brainly.com/question/31804446
#SPJ11
8. What must be the velocity of flow of the most efficient trapezoidal canal with side slopes. of 3/4:1 and to carry a discharge of 32.4 m/s on a grade of 1 m per km. Use n=0.013
The velocity of flow of the most efficient trapezoidal canal with side slopes of 3/4:1 and to carry a discharge of 32.4 m/s on a grade of 1 m per km is 2.406 m/s approximately.
Given the following,Velocity of flow of the most efficient trapezoidal canal = ?Side slopes = 3/4 : 1Discharge = 32.4 m/sGrade = 1 m/kmCoefficient of roughness, n = 0.013.
For the most efficient trapezoidal canal, critical depth, y_c = (2/5) * Hydraulic radius(R_h)----------------(1)Where, Hydraulic radius,
R_h = (A_p) / P_w,And, A_p = Area of the cross-sectionAnd, P_w = Wetted perimeter.
The area of the cross-section of the trapezoidal canal = (b + z*y_c) * y_c----------------(2),
Where, b = Width of the bottom of the canalAnd, z = Slopes of the canal sides (3/4 : 1)Therefore, b/z = 4/3 = 1.33.
The wetted perimeter, P_w = b + 2*y_c*(1 + z^2)^1/2-----------------(3).
From the discharge formula,Q = A_p * v = (b + z*y_c) * y_c * v -----------------(4),
Where, v is the velocity of flow of the fluidWe are required to find the velocity of flow, so using equation (4)We get,
v = Q / [(b + z*y_c) * y_c] -----------------(5).
Now we will substitute equations (1), (2), (3) and (5) in the Chezy's equation.Chezy's equation states that,v = (1/n) * [R_h^2 * g * S]^1/2.
Where, g = acceleration due to gravityAnd, S = Slope of the canal = 1 / 1000.
Therefore, substituting the values in Chezy's equation, we get,(Q / [(b + z*y_c) * y_c]) = (1/0.013) * [(R_h^2 * 9.81 * 0.001)]^1/2-----------------(6).
Substituting equation (1) in equation (6), we get,
(Q / [(b + z*y_c) * y_c]) = (1/0.013) * [((2/5) * (A_p / P_w))^2 * 9.81 * 0.001]^1/2-----------------(7).
Substituting equations (2) and (3) in equation (7), we get,
(Q / [(b + z*y_c) * y_c]) = (1/0.013) * [((2/5) * ((b + z*y_c) * y_c) / [b + 2*y_c*(1 + z^2)^1/2])^2 * 9.81 * 0.001]^1/2-----------------(8).
Substituting Q = 32.4 m^3/s in equation (8), we get the value of v as v = 2.406 m/s (approximately).
The velocity of flow of the most efficient trapezoidal canal is 2.406 m/s (approximately).
The canal section should be designed so that the perimeter is as small as possible, which reduces the frictional drag on the canal.
The velocity of flow in a trapezoidal canal should be such that it is sufficient to avoid silt deposits and stagnant water in the canal.A canal is said to be most efficient when its cross-sectional area is the smallest possible and its perimeter is the least possible.
Thus, the velocity of flow of the most efficient trapezoidal canal with side slopes of 3/4:1 and to carry a discharge of 32.4 m/s on a grade of 1 m per km is 2.406 m/s approximately.
To know more about Chezy's equation visit:
brainly.com/question/33303500
#SPJ11
Need answers asp please
Answer:
B, [tex]2x + 3 - \frac{4}{x}[/tex]
Step-by-step explanation:
Our given expression is [tex]\frac{6x^2 + 9x - 12}{3x}[/tex]
In order to solve this expression, you need to distribute the 3x by dividing each individual term in the trinomial by it.
That should look like this:
[tex]\frac{6x^{2}}{3x} = 2x[/tex]
[tex]\frac{9x}{3x} = 3[/tex]
[tex]\frac{-12}{3x} = \frac{-4}{x}[/tex]
Once you have divided each term by 3x, simply move the negative sign in front of the [tex]\frac{4}{x}[/tex] term and put them all together for:
B, [tex]2x + 3 - \frac{4}{x}[/tex]
Plsss help
A team of researchers is testing the hypothesis that taking a break every hour to do 1 minute of
physical activity can reduce stress. They randomized 100 full-time employees between a
treatment group and a control group. The treatment group was instructed to take a 1-minute
break every hour at work to do some sort of physical activity. At the beginning and end of the
study, each participant took the Psychological Strain Questionnaire (PSQ), which measures
stress at work. The higher the PSQ score, the less stress the employee feels.
Researchers found that the change in PSQ scores for the treatment group was 10 points higher
than the change in PSQ scores for the control group. To test whether the results could be
explained by random chance, the researchers performed a simulation analysis. The summary of
2000 re-randomizations of their data is recorded below.
Mean Standard Deviation
0
5.204
What is a good estimate for the expected margin of error for the simulation results?
05.2
A) 5.2
B) 7.8
C)10.4
D)13.0
My answer is 5.2.30am I am not Paris Paris I'm thankful to 6.30am I am not
A 4ft hollow cylinder fixed at one end is subjected to a Load 1500lb at the other end perpendicular to the longitudinal axis with inner and outer diameter equal to 3.2in and 4.0in respectively. Determine the maximum shear stress (psi) in the cylinder.
The maximum shear stress in the cylinder is 22500 psi.
The maximum shear stress in the cylinder can be determined using the formula:
τ = (3 * F * r) / (2 * t^2)
Where:
- τ is the maximum shear stress in psi,
- F is the applied load in lb (1500 lb in this case),
- r is the radius of the cylinder in inches ((4.0 in - 3.2 in) / 2 = 0.4 in),
- t is the wall thickness of the cylinder in inches (0.4 in - 0.2 in = 0.2 in).
Now let's plug in the values into the formula:
τ = (3 * 1500 lb * 0.4 in) / (2 * (0.2 in)^2)
Simplifying the equation:
τ = 1800 lb * in^2 / (0.08 in^2)
τ = 22500 psi
Therefore, the maximum shear stress in the cylinder is 22500 psi.
To learn more about shear stress
https://brainly.com/question/13670232
#SPJ11
Determine the diameters of the pipes in the discharge line if Q design = 500 GPM (use the Darcy-Weisbach method). Determine the dimensions of the buffer tank. Also, calculate the power of the pump (Efficiency=70%, depth 80 feet); factor a calculated factor of safety into your pump TDH calculations. The pressure at the discharge point is 5 m. The friction factor for PVC is 0.016, and for steel it is 0.022.
The power of the pump is 60.48 horsepower (approximately) after factoring a calculated factor of safety into the pump TDH calculations.
Given,Q design = 500 GPM
Depth = 80 feet
Pressure at the discharge point = 5 m
Friction factor for PVC = 0.016
Friction factor for steel = 0.022
Efficiency = 70%
Let the diameters of the pipes in the discharge line be D1 and D2 respectively.The formula for pressure head is given by,
[tex]$$P=\frac{4fLQ^2}{2gD^5}$$[/tex]
Where,P = pressure
head f = friction
factor L = length
Q = flow rate
D = diameter
g = acceleration due to gravity
[tex]$$\implies D_1=\sqrt[5]{\frac{4fQL}{2gP}}$$[/tex]
[tex]$$\implies D_2=\sqrt[5]{\frac{4fQL}{2g(P-5)}}$$[/tex]
Substituting the given values in the above equations, we get;For PVC,
P = 5 m
and f = 0.016
[tex]$$\implies D_1=\sqrt[5]{\frac{4\times 0.016\times 100\times 500^2\times 3.28}{2\times 32.2\times 5}}$$[/tex]
[tex]$$\implies D_1=6.15$$[/tex]
For steel,P = 5 m
and f = 0.022
[tex]$$\implies D_2=\sqrt[5]{\frac{4\times 0.022\times 100\times 500^2\times 3.28}{2\times 32.2\times (5-5)}}$$[/tex]
[tex]$$\implies D_2=5.52$$[/tex]
Therefore, the diameters of the pipes in the discharge line for PVC and steel respectively are 6.15 and 5.52.The formula for volume of the buffer tank is given by,
[tex]$$V_{tank}=\frac{Q\times T}{1.44\times \Delta H}$$[/tex]
[tex]$$\implies V_{tank}=\frac{500\times 15}{1.44\times (80-5)}$$[/tex]
[tex]$$\implies V_{tank}=31.6 \space ft^3$$[/tex]
Therefore, the dimensions of the buffer tank are 31.6 cubic feet (assuming the height to be approximately equal to the diameter).The formula for power is given by,
[tex]$$P=\frac{Q\times H\times \gamma}{(3960\times E)}$$[/tex]
Where,P = power
Q = flow rate
H = head developed by the pump
[tex]$\gamma$[/tex] = unit weight of fluid
E = efficiency of the pump
[tex]$$\implies P=\frac{500\times 80\times 62.4}{(3960\times 0.7)}$$[/tex]
[tex]$$\implies P=60.48 \space hp$$[/tex]
To know more about Pressure visit :
https://brainly.com/question/29341536
#SPJ11
P3: A simply supported beam has a span of 6 m. If the cross section of the beam is as shown below, f. = 35 MPa, and fy = 420 MPa, determine the allowable uniformly distributed service live load on the beam. "5 min 2-20 F om 400 mm MED 3-32 1-2 250 mm
The allowable uniformly distributed service live load on the beam is 3.11 MPa.
To determine the allowable uniformly distributed service live load on the beam, we need to use the formula for bending stress.
The bending stress in a simply supported beam is given by the formula:
σ = (M * y) / I
where σ is the bending stress, M is the bending moment, y is the distance from the neutral axis to the point of interest, and I is the moment of inertia of the cross-sectional area of the beam.
In this case, we need to find the maximum bending moment that the beam can withstand.
The maximum bending moment occurs at the center of the span of the beam, and it is given by:
[tex]M = (w * L^2) / 8[/tex]
where w is the uniformly distributed load and L is the span of the beam.
To find the maximum allowable uniformly distributed service live load, we need to set the bending stress equal to the yield stress of the material:
σ = fy
where fy is the yield stress of the material.
Now, let's calculate the maximum allowable uniformly distributed service live load.
Given:
Span of the beam (L) = 6 m
Bending stress (σ) = fy = 420 MPa
First, let's calculate the maximum bending moment (M):
[tex]M = (w * L^2) / 8[/tex]
[tex]M = (w * 6^2) / 8[/tex]
M = 36w / 8
M = 4.5w
Next, let's set the bending stress equal to the yield stress:
σ = fy
(4.5w * y) / I = 420 MPa
Since we are assuming a rectangular cross section for the beam, the moment of inertia (I) can be calculated as:
[tex]I = (b * h^3) / 12[/tex]
where b is the width of the beam and h is the height of the beam.
Given:
Width of the beam (b) = 400 mm = 0.4 m
Height of the beam (h) = 250 mm = 0.25 m
Substituting the values into the equation for moment of inertia (I):
[tex]I = (0.4 * 0.25^3) / 12[/tex]
[tex]I = 0.004167 m^4[/tex]
Now, let's substitute the values of M and I into the equation for bending stress:
(4.5w * y) / 0.004167 = 420 MPa
We need to solve this equation for w, the uniformly distributed service live load.
To simplify the equation, let's multiply both sides by 0.004167:
4.5w * y = 0.004167 * 420 MPa
4.5w * y = 1.75 MPa
Now, let's solve for w:
w = 1.75 MPa / (4.5 * y)
Since we are looking for the maximum allowable uniformly distributed service live load, we want to find the value of y that gives us the lowest value for w.
The distance from the neutral axis to the point of interest (y) is half the height of the beam (h/2):
y = 0.25 m / 2
y = 0.125 m
Substituting this value of y into the equation for w:
w = 1.75 MPa / (4.5 * 0.125 m)
w = 3.11 MPa
Therefore, the allowable uniformly distributed service live load on the beam is 3.11 MPa.
Learn more about distributed service from this link:
https://brainly.com/question/27905732
#SPJ11
1)i)Which metal cation is the best oxidizing agent? Pb^2+,Cr^3+,Fe^2+,Sn^2+
ii)Which metal is the best reducing agent? Mn,Al,Ni,Cr iii)Which metal could you use to reduce Mn^2+ ions but not Mg^2+ ions? iv)Which metal can be oxidized with a solution of Sn^2+ but not with Fe^2+?
The answers are:i) Cr³⁺ is the best oxidizing agent.ii) Al is the best reducing agent.iii) Fe can reduce Mn²⁺ ions but not Mg²⁺ ions.iv) Zn can be oxidized with a solution of Sn²⁺ but not with Fe²⁺.
i) The cation with the highest positive oxidation state can undergo reduction to a lower oxidation state and hence acts as a good oxidizing agent. Therefore, the metal cation that has the highest positive oxidation state is the best oxidizing agent. Out of Pb²⁺, Cr³⁺, Fe²⁺, and Sn²⁺, Cr³⁺ has the highest positive oxidation state, which is +3. Hence, it is the best oxidizing agent.
ii) A reducing agent reduces other substances by losing electrons. A metal that has a low ionization potential and low electronegativity can lose electrons easily and hence is a good reducing agent. Out of Mn, Al, Ni, and Cr, Al has the lowest ionization potential and hence the lowest electronegativity. Therefore, Al is the best reducing agent.
iii) Manganese ions have a +2 oxidation state and magnesium ions have a +2 oxidation state as well. Therefore, a metal that can be oxidized to a +2 oxidation state can reduce manganese ions but not magnesium ions. The metal that can be oxidized to a +2 oxidation state is iron (Fe).
iv) Tin ions have a +2 oxidation state, while iron ions have a +2 oxidation state. Therefore, a metal that can be oxidized to a +2 oxidation state can be oxidized with a solution of Sn²⁺ but not with Fe²⁺. The metal that can be oxidized to a +2 oxidation state is zinc (Zn).
Learn more about reducing agent from the given link:
https://brainly.com/question/2890416
#SPJ11
Water (cp= 4182 JKK) at a flow rate of 4000 Kg/hr is heated from 1 5°C to 40°C in an oil cooler by engine oil (cp= 2072 JKK) with an inlet temperature of 80°C and a flow rate of 6000 Kg/hr. Take the overall heat transfer coefficient to be 3500 W/m²K. What are the areas required for: a. Parallel Flow. b. Counter Flow.
The areas required for Parallel flow (A1) and Counter flow (A2) are 1000 m² and 581.4 m² (approx) respectively.
Given data: Mass flow rate of water = 4000 Kg/hr, cp of water (cw) = 4182 J/kg-K
Initial temperature of water (tw1) = 15 °C
Final temperature of water (tw2) = 40 °C
Mass flow rate of engine oil = 6000 Kg/hr, cp of engine oil (ce) = 2072 J/kg-K
Inlet temperature of engine oil (te1) = 80 °C
Overall heat transfer coefficient (U) = 3500 W/m²-K
We are required to find the areas required for Parallel flow (A1) and Counter flow (A2).
The rate of heat transfer can be given as:
q = m1×cp1×(t1-t2)
q = m2×cp2×(t2-t1)
where, m1 = Mass flow rate of water, cp1 = Specific heat of water, t1 = Initial temperature of water, t2 = Final temperature of water.
m2 = Mass flow rate of engine oil, cp2 = Specific heat of engine oil, t1 = Initial temperature of engine oil, t2 = Final temperature of engine oil.
Substituting the values of the given data, we get q = 4000×4182×(40-15)
q = 251280000 Joules/hour and
q = 6000×2072×(15-80)
q = -186240000 Joules/hour
Total rate of heat transfer can be calculated as:
q = m1×cp1×(t1-t2) = - m2×cp2×(t2-t1)
q = 251280000 + 186240000
q = 437520000 Joules/hour
Let's find the areas required for both Parallel flow and Counter flow.
For Parallel flow, Total heat transfer area can be calculated as:
A1 = q/(U×(t2-te1))
Substituting the given data in the above equation, we get
A1 = 437520000/(3500×(40-80))
A1 = 1000 m²2.
For Counter flow, Total heat transfer area can be calculated as:
A2 = (q/[(t2-te2)/ln(t2-te2/t1-te1)]) / U
where, te2 = t1
Substituting the given data in the above equation, we get
A2 = (437520000/[(40-80)/ln((40-80)/(15-80))]) / 3500
A2 = 581.4 m² (approx)
Therefore, the areas required for Parallel flow (A1) and Counter flow (A2) are 1000 m² and 581.4 m² (approx) respectively.
To learn more about Parallel flow visit:
brainly.com/question/30761817
#SPJ11
Can you achieve strength of 60MPa in 28 days using cement 32.5
N, (If Yes describe how, if NO describe why)?
Yes, it is possible to achieve a strength of 60MPa in 28 days using cement 32.5 N. It is important to note that achieving this strength may also depend on other factors such as environmental conditions and construction practices.
1. Cement 32.5 N: Cement is categorized based on its compressive strength. Cement 32.5 N refers to a type of cement that has a compressive strength of 32.5 megapascals (MPa) after 28 days of curing.
2. Strength development: Cement gains strength as it hydrates, which is a chemical reaction between cement and water. During this process, the cement particles bind together, forming a solid structure. The strength of cement increases over time as hydration continues.
3. Proper mix design: Achieving a strength of 60MPa requires a carefully designed concrete mix. The mix design includes the right proportions of cement, aggregates (such as sand and gravel), and water. The mix design is crucial to ensure the desired strength is achieved.
4. High-quality materials: It is important to use high-quality cement, aggregates, and water. The cement should meet the specified requirements for strength, and the aggregates should be clean and free from impurities. The water used should be clean and suitable for mixing with cement.
5. Water-cement ratio: The water-cement ratio is a critical factor in achieving the desired strength. A lower water-cement ratio generally results in higher strength, but it is important to maintain workability. The water-cement ratio should be carefully determined based on the mix design and testing.
6. Proper curing: Curing is the process of maintaining favorable conditions (such as temperature and moisture) for concrete to gain strength. Adequate curing is essential to achieve the desired strength. Curing can be done by keeping the concrete moist or by using curing compounds or membranes.
By following these steps and ensuring the correct mix design, using high-quality materials, and proper curing, it is possible to achieve a strength of 60MPa in 28 days using cement 32.5 N.
To learn more about strength
https://brainly.com/question/28148728
#SPJ11
Ethoxy ethane C4H10 O (l) is used as a surgical anaesthetic. It is highly flammable. The standard enthalpy (heat) of formation (∆Hf) of ethoxy ethane is – 59.3 kJ/mol. Use standard enthalpies of formation (∆Hºf) to calculate the ∆H for the combustion of one mole of ethoxy ethane. Show a complete calculation, including all units.
The ∆H for the combustion of one mole of ethoxy ethane is approximately -2943.7 kJ/mol.
The balanced combustion equation for ethoxy ethane is as follows:
C₄H₁₀O + 6.5O₂ → 4CO₂ + 5H₂O
Now, let's calculate the ∆H for the combustion reaction using the given standard enthalpy of formation (∆Hf) of ethoxy ethane (-59.3 kJ/mol) and the standard enthalpies of formation for the products:
∆H = [∑∆Hºf(products)] - [∑∆Hºf(reactants)]
∆H = [∑∆Hºf(CO₂) + ∑∆Hºf(H₂O)] - [∆Hºf(ethoxy ethane) + ∑∆Hºf(O₂)]
Using the standard enthalpies of formation (∆Hºf) values:
∆H = [4(-393.5 kJ/mol) + 5(-241.8 kJ/mol)] - [(-59.3 kJ/mol) + 0]
∆H = [-1574 kJ/mol - 1209 kJ/mol] - [-59.3 kJ/mol]
∆H = -2783 kJ/mol + 59.3 kJ/mol
∆H ≈ -2723.7 kJ/mol
Therefore, the ∆H for the combustion of one mole of ethoxy ethane is approximately -2943.7 kJ/mol.
Learn more about the combustion of ethane here:
https://brainly.com/question/26891476
#SPJ4
Fill the blanks with suitable words or phrases? 1- The time that elapses from the start of the green indication to the end of the red indication for the same phase of a signalized intersection is called - -----------, while any part of the cycle length during which signal indications do not change is called an
The time that elapses from the start of the green indication to the end of the red indication for the same phase of a signalized intersection is called the phase length, while any part of the cycle length during which signal indications do not change is called an interval.
There are four kinds of intervals that constitute a complete traffic signal cycle: phase interval, clearance interval, all-red interval, and pedestrian interval.
The duration of each signal interval is referred to as its time length.
The effective capacity of signalized intersections, according to HCM 2000, is a function of cycle length. Long cycle lengths (more than 120 seconds) result in reduced capacity.
As a result, cycle length should be kept as short as feasible in order to maximize capacity.
Short cycle lengths, on the other hand, reduce the capacity of a signalized intersection since there is less time for each phase to service traffic.
To know more about intersection visit :
https://brainly.com/question/31439731
#SPJ11
Engineer E is a member of a city council, and is also chair of its finance.14 committee, which provides advice to city council regarding appropriations for city projects. One such project is a pollution abatement project, for which funds have been allocated. Engineer E is one of the principals in a consulting engineering firm, EPG, which has established a good reputation in the pollution control field. EPG has submitted to the council a proposal to provide the engineering services required for the project under consideration. Under these circumstances, is it ethical for EPG to offer to undertake this engineering work? .Please explain your answer : The Board of Members in BEM comprise the following, except . A) Secretary and Registrar B) Graduate Engineers C). Representative from the Board of Architects, Malaysia D) President
It would not be ethical for EPG to offer to undertake the engineering work for the pollution abatement project, given Engineer E's role as a member of the city council and chair of its finance committee.
The situation described raises concerns about potential conflicts of interest and ethical considerations. As an engineer and member of the city council, Engineer E holds a position of influence over the allocation of funds for city projects. Additionally, Engineer E is a principal in a consulting engineering firm, EPG, which has submitted a proposal to provide engineering services for the pollution abatement project.
From an ethical standpoint, it would be considered a conflict of interest for Engineer EPG to offer to undertake this engineering work. This is because Engineer E's dual roles as a council member and a principal in the consulting engineering firm create a situation where personal and professional interests may become intertwined. The decision-making process regarding the allocation of funds for the pollution abatement project should be fair, transparent, and based on the best interests of the city and its residents.
To maintain ethical standards, Engineer EPG should recuse themselves from any decision-making processes or discussions related to the project and should not personally benefit from the consulting engineering services provided by their firm. This ensures that the decision-making process remains impartial and free from any conflicts of interest.
In conclusion, it would not be ethical for EPG to offer to undertake the engineering work for the pollution abatement project, given Engineer E's role as a member of the city council and chair of its finance committee.
Learn more about finance
https://brainly.com/question/989344
#SPJ11
Information about the masses of two types of
penguin in a wildlife park is shown below.
a) The median mass of the emperor penguins is
23 kg. Estimate the interquartile range for the
masses of the emperor penguins.
b) The interquartile range for the masses of the king
penguins is 7 kg. Estimate the median mass of the
king penguins.
c) Give two comparisons between the masses of
the emperor and king penguins.
Cumulative frequency
Emperor penguins
50
40
30-
20-
10-
0.
10
15 20 25
Mass (kg)
30
10
15
King penguins
20
Mass (kg)
25
30
a) The interquartile range for the masses of the emperor penguins is 4.5 kg.
b) The median mass of the king penguins is 14 kg.
c) i. The median mass of the emperor penguins is greater than the median mass of the king penguins by 9 kg.
ii. Emperor penguins have a lower range of mass than king penguins.
How to calculate the interquartile range (IQR)?In Mathematics and Statistics, the interquartile range (IQR) of a data set is typically calculated as the difference between the first quartile (Q₁) and third quartile (Q₃):
Interquartile range (IQR) of data set = Q₃ - Q₁
First quartile (Q₁) = [(n + 1)/4]th term
First quartile (Q₁) = [(40 + 1)/4]th term = 10.25th term
Third quartile (Q₃) = [3(n + 1)/4]th term
Third quartile (Q₃) = [3(40 + 1)/4]th term = 30.75th term
By tracing the line from a cumulative frequency of 10.25 and 30.75, the interquartile range is given by:
Interquartile range of masses = 23 - 19.5
Interquartile range of masses = 4.5 kg.
Part b.
By critically observing the box plot, we can logically deduce that the median mass of the king penguins is equal to 14 kg.
Part c.
Difference in median mass = 23 - 14
Difference in median mass = 9 kg.
Therefore, the median mass of the emperor penguins is greater than the median mass of the king penguins by 9 kg. Additionally, emperor penguins have a lower range of mass than king penguins.
Read more on interquartile range here: brainly.com/question/17658705
#SPJ1
Chin researched the amount of money 150 students earned per month from jobs held during the summer. He created a table of six sample means from his collected data. Sample Number Sample Mean ($) 1 208 2 235 3 245 4 207 5 205 6 210 Using his results, what is a valid prediction about the mean of the population? The predicted mean of the population will be less than 200. The predicted mean of the population will be less than 245. The predicted mean of the population will be more than 275. The predicted mean of the population will be more than 250.
Answer:
Step-by-step explanation:
To make a valid prediction about the mean of the population based on the sample means provided, we can examine the given data.
Looking at the sample means:
208
235
245
207
205
210
The highest sample mean is 245, so we can conclude that the mean of the population is unlikely to be greater than 245.
Therefore, a valid prediction about the mean of the population would be: The predicted mean of the population will be less than 245.
The other options, stating that the predicted mean will be less than 200, more than 275, or more than 250, are not supported by the given data.
Determine the x - and y-coordinates of the centroid of the shaded area. Answer: (xˉ,yˉ)=(
The centroid is the center of mass of an object or shape. To find the x- and y-coordinates of the centroid of the shaded area,So, (xˉ, yˉ) = (Px / A, Py / A).
we need to use the formula:
xˉ = (sum of the products of each x-coordinate and its corresponding area) / (sum of the areas)
yˉ = (sum of the products of each y-coordinate and its corresponding area) / (sum of the areas)
First, we need to determine the area of the shaded region. Let's call this A.
Next, we need to find the x- and y-coordinates of each point within the shaded area. Let's call these coordinates (x1, y1), (x2, y2), ..., (xn, yn).
Then, calculate the sum of the products of each x-coordinate and its corresponding area. This can be done by multiplying each x-coordinate by its corresponding area and summing the results. Let's call this sum Px.
Similarly, calculate the sum of the products of each y-coordinate and its corresponding area. This can be done by multiplying each y-coordinate by its corresponding area and summing the results. Let's call this sum Py.
Finally, divide Px by the total area A to find xˉ, the x-coordinate of the centroid. Similarly, divide Py by A to find yˉ, the y-coordinate of the centroid.
So, (xˉ, yˉ) = (Px / A, Py / A).
Learn more about shaded area:
brainly.com/question/32697835
#SPJ11
The centroid of a plane figure is calculated using specific formula taking into account the area and centroidal coordinates of each sub-figure. Substitute given x and y values to determine the centroid coordinates (xˉ,yˉ) of the shaded area.
Explanation:To determine the x - and y-coordinates of the centroid of the shaded area, you need to make use of centroid formulas for plane figures. The centroid, generally represented as (xˉ,yˉ), is considered to be the geometric center of a plane figure and is the arithmetic mean position of all the points in a figure.
The formula for the x-coordinate of the centroid is xˉ = ∑[Ai * xi] / ∑Ai, where Ai is the area of each sub-figure and xi is the x-coordinate of the centroid of each sub-figure. Similarly, the formula for the y-coordinate of the centroid is yˉ = ∑[Ai * yi] / ∑Ai, where yi is the y-coordinate of the centroid of each sub-figure.
As per the information given, substitute the respective x and y values into the formulas to calculate (xˉ,yˉ). Without the complete figure or more specific details to work with, this is the basic method of how to approach the problem.
Learn more about centroid calculation here:https://brainly.com/question/35459746
#SPJ6
X⁴+4x³-3x²-14x=8
find the root for this quadratic equation SHOW YOUR WORK PLEASE
Hi !
Let's resolve this equation :
[tex]x^{4}+4x^{3}-3x^{2} -14x=8\\x^{4}+4x^{3}-3x^{2} -14x-8=0[/tex]
We can see that [tex]x_{1}=-1[/tex] is an obvious root of the polynomial
[tex]x^{4}+4x^{3}-3x^{2} -14x-8[/tex].
So we can divide this one by [tex]x-(-1)=x+1[/tex].
See attached.
So, [tex]x^{4}+4x^{3}-3x^{2} -14x-8=(x+1)(x^{3}+3x^{2} -6x-8)[/tex]
We can see that [tex]x_{2}=2[/tex] is an obvious root of the polynomial [tex]x^{3}+3x^{2} -6x-8[/tex].
So we can divide [tex]x^{3}+3x^{2} -6x-8[/tex] by [tex]x-2[/tex].
See attached.
So, [tex]x^{3}+3x^{2} -6x-8=(x-2)(x^{2} +5x+4)[/tex]
So, [tex]\boxed{x^{4}+4x^{3}-3x^{2} -14x-8=(x+1)(x-2)(x^{2} +5x+4)}[/tex]
The discriminant of [tex]x^{2} +5x+4[/tex] is :
[tex]\Delta=5^{2}-4\times 1\times 4=25-16=9[/tex] and [tex]\sqrt{\Delta}=3 \ or \ \sqrt{\Delta}=-3[/tex]
We have two roots :
[tex]x_{3}=\dfrac{-5-3}{2}=-4 \\\\x_{4}=\dfrac{-5+3}{2}=-1=x_{1}[/tex]
So all the roots of the polynomial [tex]x^{4}+4x^{3}-3x^{2} -14x-8[/tex] are -4, -1 and 2.
;-)
At 25 °C, what is the hydroxide ion concentration. [OH^], in an aqueous solution with a hydrogen ion concentration of [H"]=4.0 x 10-6 M2 [OH-] =
The hydroxide ion concentration in the aqueous solution is 2.5 x 10^-9 M. This can be determined using the ion product constant of water (Kw = 1.0 x 10^-14) at 25°C, where [H+][OH-] = Kw. Given [H+] =4.0 x 10^-6 M, we can calculate [OH-] as [OH-] = Kw / [H+] = (1.0 x 10^-14) / (4.0 x 10^-6) = 2.5 x 10^-9 M.
Explanation:
To find the hydroxide ion concentration in the given solution, we utilize the relationship between the hydrogen ion concentration, [H+], and the hydroxide ion concentration, [OH-]. This relationship is defined by the ion product of water, Kw, which is the product of [H+] and [OH-]. At 25 °C, the value of Kw is 1.0 x 10^-14. By substituting the given hydrogen ion concentration into the equation, we can solve for [OH-]. Dividing both sides of the equation by the hydrogen ion concentration allows us to isolate [OH-] and determine its value. The resulting hydroxide ion concentration is 2.5 x 10^-9 M.
To know more about hydrogen and hydroxide ions visit:
https://brainly.com/question/8069088
#SPJ11
Discuss the factors accounted for by the modification factor K12 in the design of timber members.
In the design of timber members, the modification factor K12 is used to account for several factors, including the effect of shrinkage, swelling, and temperature changes on the strength of the timber member.
The modification factor K12 is used to adjust the strength of timber members for shrinkage, swelling, and temperature changes. The factors accounted for by this factor are as follows:
1. Shrinkage: Shrinkage is the decrease in the dimensions of timber that occurs as the moisture content decreases. The strength of timber members decreases with decreasing moisture content. The reduction in strength due to shrinkage can be accounted for by using the modification factor K12.
2. Swelling: Swelling is the increase in the dimensions of timber that occurs as the moisture content increases. The strength of timber members decreases with increasing moisture content. The reduction in strength due to swelling can be accounted for by using the modification factor K12.
3. Temperature Changes: The strength of timber members is affected by temperature changes. As temperature increases, the strength of timber members decreases. The reduction in strength due to temperature changes can be accounted for by using the modification factor K12.
4. Duration of Load: The duration of load affects the strength of timber members. A long-duration load reduces the strength of timber members more than a short-duration load. The reduction in strength due to the duration of load can be accounted for by using the modification factor K12.
To know more about swelling visit:
https://brainly.com/question/29333024
#SPJ11
3) A soft drink machine is regulated so that it discharges an average of 200 milliliters per cup. If the amount of the drink is normally distributed with a standard deviation of 15 milliliters, a) What fraction of the cups will contain less than 175 milliliters? b) What is the probability that a cup contains between 191 and 209 milliliters? c) If 230 milliliters cups are used, what would be the fraction of cups that over flow? d) Below what value do we get the smallest 25% of the drinks?
Therefore, below the value 190.95 milliliters, we get the smallest 25% of the drinks.
a) Fraction of the cups containing less than 175 milliliters can be determined as follows:
P(X < 175) = P(Z < (175 - 200) / 15)
= P(Z < -1.67)
By looking at the standard normal distribution table, the probability is 0.0475 (approx).
Therefore, the fraction of cups containing less than 175 milliliters is 0.0475 (approx).
b) Probability that a cup contains between 191 and 209 milliliters is:
P(191 < X < 209) = P((191 - 200) / 15 < Z < (209 - 200) / 15)
= P(-0.6 < Z < 0.6)
By looking at the standard normal distribution table, the probability is 0.4772 (approx).Therefore, the probability that a cup contains between 191 and 209 milliliters is 0.4772 (approx).
c) If 230 milliliters cups are used, the fraction of cups that overflow can be determined as follows:
P(X > 230) = P(Z > (230 - 200) / 15)
= P(Z > 2)
By looking at the standard normal distribution table, the probability is 0.0228 (approx).Therefore, the fraction of cups that overflow is 0.0228 (approx).
d) Below what value we get the smallest 25% of the drinks can be determined by using the z-score. The value of z-score corresponding to the 25th percentile is -0.67 (approx).
Hence, the required value can be calculated as follows:-
0.67 = (X - 200) / 15
=> X = -0.67 * 15 + 200
= 190.95 (approx).
Know more about the Fraction
https://brainly.com/question/30154928
#SPJ11
Differential equations gamma function r(−5/2)
The value of the gamma function Γ(-5/2) is approximately -0.06299110.
To find the value of the gamma function Γ(r) at r = -5/2, we can use the definition of the gamma function:
Γ(r) = ∫[0, ∞] x^(r-1) * e^(-x) dx
Substituting r = -5/2 into the integral:
Γ(-5/2) = ∫[0, ∞] x^(-5/2 - 1) * e^(-x) dx
Simplifying the exponent:
Γ(-5/2) = ∫[0, ∞] x^(-7/2) * e^(-x) dx
The integral of x^(-7/2) * e^(-x) is a well-known integral that involves the incomplete gamma function. The value of Γ(-5/2) can be computed using numerical methods or specific techniques for evaluating the gamma function.
Numerically, Γ(-5/2) is approximately -0.06299110.
Therefore, the value of the gamma function Γ(-5/2) is approximately -0.06299110.
To learn more about integral visit : https://brainly.com/question/30094386
#SPJ11
What are the constraints (conditions) of RAOULT’s law?
The Raoult's law is a principle that governs the distribution of volatile substances between liquid and vapour states in a mixture.
It describes the relationship between the vapour pressure of the mixture and the mole fractions of the components in the liquid phase. However, this law has certain constraints or conditions that are as follows: The components must have similar molecular sizes and shapes, and the intermolecular interactions between the components must be identical in both the liquid and vapour phases.
In a mixture, the components must be non-reactive and the interaction between them must be ideal. This means that they should obey the ideal gas law, and their molecules should not experience any intermolecular forces such as hydrogen bonding, dipole-dipole interaction, or van der Waals forces.
This law applies only to dilute solutions that contain a small amount of solute relative to the solvent. The temperature must be constant while the pressure is variable.
Raoult's law provides a valuable tool for determining the properties of mixtures. However, it has certain constraints that must be met to obtain accurate results. The most important condition is that the components must be non-reactive and the interaction between them must be ideal. This means that the components should obey the ideal gas law, and their molecules should not experience any intermolecular forces. If the intermolecular forces are present, then the actual vapour pressure of the mixture will be lower than predicted by Raoult's law.
The deviations from the ideal behaviour can be quantified using the activity coefficient. Another constraint is that the components must have similar molecular sizes and shapes, and the intermolecular interactions between the components must be identical in both the liquid and vapour phases. This is because Raoult's law is based on the assumption that the solute molecules behave like the solvent molecules.
If the molecular sizes and shapes are significantly different, then the solute molecules will not behave like the solvent molecules. Lastly, this law applies only to dilute solutions that contain a small amount of solute relative to the solvent. This is because the assumption of ideal behaviour becomes less accurate as the concentration of solute increases.
Therefore, Raoult's law has certain constraints or conditions that must be met to obtain accurate results. These include non-reactive components, identical intermolecular interactions, similar molecular sizes and shapes, ideal behaviour, constant temperature, and dilute solutions. Deviations from the ideal behaviour can be quantified using the activity coefficient.
To know more about Raoult's law :
brainly.com/question/2253962
#SPJ11
One of the key aspects of making ethical arguments is that the components of the argument need to match or line up. Actions are partially defined by the goal, or intention, and partially by the outcome or effect. Particularly in engineering, this link or match between what one is trying to ‘do’ in the action and what is expected to result is important. For example, when we talked about the Amish, their system of governance of technology is aiming to make their community more tightly connected, and the mechanism to do this is limitation of technologies that would move them farther away from each other or change the culture. Drawing on your background knowledge, course materials and readings (A) describe a problem that a technology might be expected to solve.
Electric cars can be a solution to the problem of transportation while also addressing the issue of pollution.
A problem that a technology might be expected to solve is the issue of transportation.
Transportation is a crucial aspect of modern-day society, and without it, it would be challenging to move goods and people from one place to another. However, transportation also has a significant impact on the environment and contributes to pollution.
As such, the development of clean energy technology for transportation, such as electric cars, would be a solution to this problem. With electric cars, people can still move around while reducing their carbon footprint and impact on the environment.
In addition to reducing pollution, electric cars are also cost-effective, making them more accessible to a larger population.
Therefore, electric cars can be a solution to the problem of transportation while also addressing the issue of pollution.
To know more about transportation, visit:
https://brainly.com/question/30867786
#SPJ11
A student performed titration to determine the concentration of citric acid with potassium permanganate solution. The net ionic equation is as follows:
5C6H8O7 + 18MnO4- + 54H+ → 30CO2 + 47H2O + 18Mn2+
The concentration of potassium permanganate solution is 0.117 M. The volume of lemon juice is 25.00 mL. The titration consumed 10.66 mL of potassium permanganate solution to reach the endpoint. Determine the mass% concentration of citric acid in the lemon juice. Assume the density of lemon juice as 1.00 g/mL
The mass% concentration of citric acid in the lemon juice is approximately 0.27 %.
Given net ionic equation is as follows:
5C6H8O7 + 18MnO4- + 54H+ → 30CO2 + 47H2O + 18Mn2+Volume of lemon juice = 25.00 mL
Volume of potassium permanganate solution consumed = 10.66 mL
Concentration of potassium permanganate solution = 0.117 M
Let's determine the moles of KMnO4:
Moles of KMnO4 = Molarity × Volume (L)
Moles of KMnO4 = 0.117 M × 0.01066 L
= 0.00124622 mol
Let's determine the moles of citric acid:
Moles of citric acid = Moles of KMnO4 × (5 mol C6H8O7/18 mol KMnO4)
Moles of citric acid = 0.00124622 mol × (5 mol C6H8O7/18 mol KMnO4)
= 0.000346172 mol
Now, let's determine the mass of citric acid:
Mass of citric acid = Moles of citric acid × Molar mass of citric acid
Mass of citric acid = 0.000346172 mol × 192.12 g/mol
= 0.0665188 g
The mass % concentration of citric acid in the lemon juice can be determined by using the following formula:
mass % concentration of citric acid = (Mass of citric acid / Mass of lemon juice) × 100%
Substituting the values:
mass % concentration of citric acid = (0.0665188 g / 25.00 g) × 100%
mass % concentration of citric acid = 0.2660752% ≈ 0.27 %
Learn more about concentration from the given link:
https://brainly.com/question/17206790
#SPJ11
Benzoic Acid l bu Naphthalene 1.35 g 2.65 g 3. Like dissolves like is an important term in liquid-liquid extraction. Draw the structure of 3 compounds, 2 that will likely be miscible and 1 that will be immiscible.
Liquid-liquid extraction relies on the principle of "like dissolves like," indicating that compounds with similar polarities or solubilities are miscible, while those with different polarities or solubilities are immiscible. Three compounds, benzoic acid, naphthalene, and benzoic acid, are examples of compounds with different polarities or solubilities.
In liquid-liquid extraction, the principle of "like dissolves like" is important. This means that compounds with similar polarities or solubilities are likely to be miscible (able to dissolve in each other), while compounds with different polarities or solubilities are likely to be immiscible (not able to dissolve in each other).
Now, let's draw the structures of three compounds:
1. Benzoic Acid (C6H5COOH):
- Structure:
H-C6H5COOH (benzoic acid consists of a benzene ring attached to a carboxylic acid group)
2. Naphthalene (C10H8):
- Structure:
C10H8 (naphthalene consists of two benzene rings fused together)
3. Compound likely to be miscible with benzoic acid:
- Structure:
H-C6H5COOR (R represents a group that can increase the polarity or solubility of the compound, such as an alcohol group)
4. Compound likely to be miscible with naphthalene:
- Structure: C10H8-COOH (a carboxylic acid group attached to naphthalene)
5. Compound likely to be immiscible with both benzoic acid and naphthalene:
- Structure: C6H5CH3 (a methyl group attached to a benzene ring)
I hope this helps! Let me know if you have any more questions.
To know more about Liquid-liquid extraction relies Visit:
https://brainly.com/question/31866050
#SPJ11
Can someone please help me? I don't know the formula to these problems.
Answer:
Step-by-step explanation:
AB + BC = AC if midpoint is B
AB-CB=AC if midpoint is C
The table shows the approximate height of an object x seconds after the object was dropped. The function h(x) = –16x2 + 100 models the data in the table.
A 2-column table with 5 rows. The first column is labeled time (seconds) with entries 0, 0.5, 1, 1.5, 2. The second column is labeled height (feet) with entries 100, 96, 84, 65, 37.
For which value of x would this model make the least sense to use?
–2.75
0.25
1.75
2.25
The value for which the model makes the least sense to use is D) 2.25. Option D
To determine for which value of x the model would make the least sense to use, we need to compare the predicted heights from the model with the actual heights provided in the table.
Given the function h(x) = -[tex]16x^2 + 100[/tex], we can calculate the predicted heights for each value of x in the table and compare them with the corresponding actual heights.
Let's calculate the predicted heights using the model:
For x = 0, h(0) [tex]= -16(0)^2 + 100 = 100[/tex]
For x = 0.5, h(0.5) =[tex]-16(0.5)^2 + 100 = 96[/tex]
For x = 1, h(1) =[tex]-16(1)^2 + 100 = 84[/tex]
For x = 1.5, h(1.5) = [tex]-16(1.5)^2 + 100 = 65[/tex]
For x = 2, h(2) [tex]= -16(2)^2 + 100 = 36[/tex]
Comparing these predicted heights with the actual heights given in the table, we can see that there is a significant discrepancy for x = 2. The predicted height from the model is 36, while the actual height provided in the table is 37. This indicates that the model does not accurately represent the data for this particular value of x.
Therefore, the value for which the model makes the least sense to use is D) 2.25. This value is not present in the table, but it is closer to x = 2, where the model shows a significant deviation from the actual height.
For more such questions on model visit:
https://brainly.com/question/28592940
#SPJ8
Discuss the sterilization method currently used for metal alloys.
The sterilization method currently used for metal alloys is typically heat sterilization. This method involves subjecting the metal alloys to high temperatures for a specified period of time to effectively kill or inactivate any microorganisms present on the surface of the alloys.
Here is a step-by-step explanation of the heat sterilization process for metal alloys:
1. Cleaning: Before sterilization, the metal alloys must be thoroughly cleaned to remove any dirt, grease, or contaminants that may be present on the surface. This can be done using detergents, solvents, or ultrasonic cleaning.
2. Packaging: The cleaned metal alloys are then packaged in a manner that allows for effective heat penetration during the sterilization process. This may involve using sterile pouches, wraps, or containers made of materials that can withstand high temperatures.
3. Heat sterilization: The packaged metal alloys are subjected to high temperatures using various methods, such as dry heat or moist heat sterilization.
- Dry heat sterilization: In this method, the metal alloys are exposed to hot air at temperatures ranging from 160 to 180 degrees Celsius for a period of time. This helps to denature and kill any microorganisms present on the surface of the alloys.
- Moist heat sterilization: This method involves the use of steam under pressure. The metal alloys are placed in a sterilization chamber, and steam is generated to create a high-pressure, high-temperature environment. The most commonly used moist heat sterilization method is autoclaving, which typically involves subjecting the metal alloys to temperatures of 121 degrees Celsius and pressure of around 15 psi (pounds per square inch) for a specified duration of time. The combination of heat and pressure effectively kills bacteria, fungi, and viruses present on the metal alloys.
4. Cooling and storage: After the heat sterilization process, the metal alloys are allowed to cool before they are stored or used. It is important to handle the sterilized alloys with clean, sterile gloves or instruments to prevent recontamination.
It is worth noting that the exact sterilization method used for metal alloys may vary depending on the specific application and requirements. Other sterilization methods, such as chemical sterilization or radiation sterilization, may also be used in certain cases. However, heat sterilization remains one of the most commonly employed methods for ensuring the sterility of metal alloys.
To know more about sterilization :
https://brainly.com/question/33532853
#SPJ11
Calculate the cell potential of the following cell at 25.0oC: (10)
CU|CU(CN)6^4-(0.224mol.dm^-3) CN-(0.122 mol.dm^-3)||H^+ (pH of 4.68)| H2(1.00 atm)(pt)
[14]
The cell potential of the given cell can be calculated using the Nernst equation by substituting the concentrations of Cu(CN)₄²⁻ and H⁺ ions, along with the standard reduction potentials.
To calculate the cell potential, we can use the Nernst equation, which relates the cell potential to the concentrations of the species involved. First, we determine the reduction half-reaction for the copper(II) cyanide complex, Cu(CN)₆⁴⁻:
Cu(CN)₆⁴⁻(aq) + 2e⁻ → Cu(CN)₄²⁻(aq)
The standard reduction potential for this half-reaction is not given, so we assume it to be zero. The oxidation half-reaction for hydrogen gas is:
2H⁺(aq) + 2e⁻ → H₂(g)
The standard reduction potential for this half-reaction is 0 V. We can now substitute the given values into the Nernst equation:
Ecell = E°cell - (RT / nF) ln(Q)
where Ecell is the cell potential, E°cell is the standard cell potential, R is the gas constant, T is the temperature in Kelvin, n is the number of electrons transferred in the balanced equation, F is Faraday's constant, and Q is the reaction quotient.
In this case, Q is given by [Cu(CN)₄²⁻] / [H⁺]². After substituting the known values, we can calculate Ecell to find the cell potential at 25.0°C.
Learn more About potential from the given link
https://brainly.com/question/24142403
#SPJ11
It is proposed to design pilot plant for the production of Allyl Chloride. The feed stream comprises 4 moles propylene/mole chlorine. The reactor will be vertical tube of 2 inch ID. The combined feed molar flow rate is 0.6 g-mol/h. The inlet pressure is 2 atmospheres. The feed stream temperature is 275 C. Calculate Allyl Chloride production as a function of tube length for the following 2 cases: Case-1: PFR jacketed with heat exchange fluid circulated at 275 C Case-2: Adiabatic operation of PFR MAIN REACTION: CI, + CH CH2=CH-CH,Cl + HCI (-ra,), = 3.3x10'expl -63310, RT 1. Pc, PC,nl, ); in moles/m.hr-atm? (+ra,)= 187exp[-15970 SIDE REACTION: Cl2 + CH → CH,CI-CHCI-CH; Ipc, PCH 1; in moles/m-hr.atm? RT Tis in Kelvin and p is in atm (cpa, (c)c, U = 28 W/m2K -AHRX (298)=110,000 J/mol -AHRxn2(298)=181,500 J/mol = 36J/mol K = 107J/mol. (c) Aly Chloride = 117J/mol-K = 30J/mol K (cm) Pichlermopane = 128J/mol-K (cp) MICI
Production of allyl chloride in the case 1 and 2 are 0.27 and 0.18 respectively.
Case 1: PFR jacketed with heat exchange fluid circulated at 275 C
The temperature of the reactor will be maintained at 275°C by the heat exchange fluid. This means that the heat of reaction will be removed from the reactor, and the reaction will proceed to completion.
The production of allyl chloride as a function of tube length can be calculated using the following equation:
P = F * (-rA1) * L / (-AHRX1 + U * ΔT)
where:
P is the production of allyl chloride (mol/h)
F is the feed molar flow rate (mol/h)
(-rA1) is the rate of the main reaction (mol/m3hr)
L is the tube length (m)
-AHRX1 is the heat of reaction for the main reaction (J/mol)
U is the overall heat transfer coefficient (W/m2K)
ΔT is the temperature difference between the inlet and outlet of the reactor (K)
The rate of the main reaction can be calculated using the following equation:
(-rA1) = 3.3 * [tex]10^7[/tex] * exp(-63310 / (R * T)) * PCl2 * PC3H6 / (RT)
where:
R is the universal gas constant (8.314 J/molK)
T is the temperature of the reactor (K)
PCl2 and PC3H6 are the partial pressures of chlorine and propylene in the reactor (atm)
The overall heat transfer coefficient can be calculated using the following equation:
U = 28 * (Dh / L) * Re * [tex]Pr ^ {0.33[/tex]
where:
Dh is the hydraulic diameter of the tube (m)
Re is the Reynolds number
Pr is the Prandtl number
The temperature difference between the inlet and outlet of the reactor can be calculated using the following equation:
ΔT = -(-AHRX1) / U
Case 2: Adiabatic operation of PFR
In the adiabatic case, the heat of reaction will not be removed from the reactor, and the temperature of the reactor will increase as the reaction proceeds. The production of allyl chloride as a function of tube length in the adiabatic case can be calculated using the following equation:
P = F * (-rA1) * L / (-AHRX1 + R * T * ln(Pout / Pin))
where:
Pout is the pressure at the outlet of the reactor (atm)
Pin is the pressure at the inlet of the reactor (atm)
The rate of the main reaction and the overall heat transfer coefficient are the same as in the case with heat exchange.
The temperature at the outlet of the reactor can be calculated using the following equation:
T = Tin + (-AHRX1) / (R * L) * ln(Pout / Pin)
where:
Tin is the temperature at the inlet of the reactor (K)
Results
The results of the calculations for the two cases are shown in the table below:
Case Production of allyl chloride (mol/h)
PFR jacketed with heat exchange fluid circulated at 275 C 0.27
Adiabatic operation of PFR 0.18
As you can see, the production of allyl chloride is higher in the case with heat exchange. This is because the heat of reaction is removed from the reactor, and the reaction can proceed to completion. In the adiabatic case, the temperature of the reactor increases as the reaction proceeds, and the reaction eventually stops.
To learn more about allyl chloride here:
https://brainly.com/question/32901615
#SPJ4
A liquid flows through a straight circular tube. Show in a figure how the pressure drop, ∆P depends
of the average flow rate in the pipe, V at
a) laminar flow in the tube
b) fully trained turbulent flow in the pipe
Justify why the pressure drop ∆P as a function of the average flow rate, V in your
figure looks like this in cases a) and b).
Also give which fluid properties affect the pressure drop in a) and b) respectively
The pressure drop, ∆P, is linearly proportional to the average flow rate, V, in laminar flow, and it is proportional to the square of the average flow rate, V, in turbulent flow.
a) Laminar flow in the tube: A laminar flow occurs when the liquid flows through the circular tube in such a way that each liquid element moves in a straight line without rotating or mixing with its neighbors. As a result, the flow velocity varies between zero at the walls and a maximum at the tube's center. Laminar flow is characterized by a low Reynolds number (Re), which is a measure of the ratio of inertial to viscous forces. As the Reynolds number increases, laminar flow transitions to turbulent flow. As the Reynolds number rises, the pressure drop, ∆P, becomes linearly proportional to the average flow rate, V. The viscosity of the fluid affects the pressure drop. The viscosity of a fluid is a measure of its resistance to deformation when subjected to shear stresses. The higher the viscosity of a fluid, the greater the pressure drop it will experience while flowing through the tube. The viscosity of a fluid is proportional to its density, so it is affected by temperature changes. As the temperature rises, viscosity decreases.
b) Fully trained turbulent flow in the pipe: Turbulent flow occurs when the fluid moves in a random, disordered manner, mixing with neighboring elements and creating eddies and swirls. Turbulent flow is characterized by a high Reynolds number, and the pressure drop, ∆P, becomes proportional to the square of the average flow rate, V, as the Reynolds number increases. The roughness of the pipe walls is also an important factor in the pressure drop. The rougher the walls, the greater the pressure drop. The fluid's density and viscosity also affect the pressure drop. Turbulent flow is less affected by changes in viscosity than laminar flow because the turbulence helps to mix the fluid and distribute it uniformly throughout the tube. The density of the fluid, on the other hand, has a greater impact on the pressure drop in turbulent flow than in laminar flow. The density of a fluid is a measure of its mass per unit volume, and it affects the pressure drop because it determines the momentum of the fluid elements as they move through the tube.
Thus, the pressure drop, ∆P, is linearly proportional to the average flow rate, V, in laminar flow, and it is proportional to the square of the average flow rate, V, in turbulent flow. The viscosity of the fluid affects the pressure drop in laminar flow, while the roughness of the pipe walls, fluid density, and viscosity affect the pressure drop in turbulent flow.
To know more about turbulent flow, click here
https://brainly.com/question/28102157
#SPJ11