The efficiency of the engine is 66.67%.Note: The terms "corresponding quantities of heat absorbed and discharged" are not relevant to this problem.
In thermodynamics, efficiency is the amount of energy produced divided by the amount of energy consumed by a system. It can be defined as the ratio of output work to input energy. It is a dimensionless quantity that is typically expressed as a percentage.
In the given problem, the efficiency of an engine is to be calculated. The work done by the engine is 100.0 J, and the heat discharged is 50.0 J.
Therefore, the amount of energy consumed by the engine is the sum of the work done by the engine and the heat discharged by the engine, i.e., 100.0 J + 50.0 J = 150.0 J.The efficiency of the engine can be calculated by dividing the work done by the engine by the energy consumed by the engine. Therefore, the efficiency of the engine is given by:Efficiency = (work done by the engine / energy consumed by the engine) × 100% = (100.0 J / 150.0 J) × 100% = 66.67%.
Therefore, the efficiency of the engine is 66.67%.Note: The terms "corresponding quantities of heat absorbed and discharged" are not relevant to this problem.
to know more about engine
https://brainly.com/question/25257437
#SPJ11
During dry conditions, a hiker climbs from 5300 ∘
to 6000 ∘
. At 5300 ′
, the temperature is 60F. What is the most likely femperature at 6000 ? Provide your answer in F (no unit, just the number).
The temperature at 6000 is likely to be 53°F. The reason is that as one climbs up the mountain, the temperature decreases by approximately 3.5°F every 1000 feet of elevation gain.
Here, the elevation gain is 700 feet, so the temperature is expected to drop by around 24.5°F (700/1000 × 3.5). Therefore, if the temperature is 60°F at 5300 feet, it is expected to be 60°F - 24.5°F = 35.5°F lower at 6000 feet.
A hiker climbing from 5300 ft to 6000 ft during dry conditions can expect a change in temperature. The temperature difference arises due to the difference in elevation between the two points. As the hiker gains elevation, the temperature generally decreases. To determine the temperature at the top of the climb, one can use the estimated rate of temperature drop per unit elevation gain.
On average, the temperature drops by about 3.5°F per 1000 feet of elevation gain. The elevation gain in this problem is 700 feet (6000-5300), so the temperature change can be estimated to be -24.5°F (700/1000 x -3.5°F).
Since the temperature at 5300 feet is given to be 60°F, we can subtract the change in temperature from the starting temperature to find the most likely temperature at 6000 feet. The resulting temperature is 60°F - 24.5°F = 35.5°F. Therefore, the most likely temperature at 6000 feet is 35.5°F.
The temperature at 6000 is expected to be 53°F, as the elevation difference between the two points is 700 feet and the temperature usually drops by around 3.5°F every 1000 feet of elevation gain. As a result, we can conclude that if the temperature is 60°F at 5300 feet, it is expected to be 60°F - 24.5°F = 35.5°F lower at 6000 feet.
To know more about temperature :
brainly.com/question/7510619
#SPJ11
What is the electric potential at a point 0.75 m away from a point charge of 3.5m C?
The electric potential at a distance of 0.75 m from a point charge of 3.5 mC is estimated to be around 41.79 V.
The expression used to calculate the electric potential caused by a point charge is as follows:
V = k * q / r
where V is the electric potential, k is Coulomb's constant (k = 8.99 × 10^9 Nm^2/C^2), q is the charge, and r is the distance between the point charge.
q = 3.5 × 10^-6 C (charge)
r = 0.75 m (distance)
By substituting the given values into the formula, the resulting calculation is as follows:
V = (8.99 × 10^9 Nm^2/C^2) * (3.5 × 10^-6 C) / 0.75 m
Calculating this expression, we find:
V ≈ 41.79 V
Therefore, the electric potential at a distance of 0.75 m from a point charge of 3.5 mC is estimated to be around 41.79 V.
Learn more about electric potential at: https://brainly.com/question/26978411
#SPJ11
An object is located 72 cm from a thin diverging lens along the axis. If a virtual image forms at a distance of 18 cm from the lens, what is the focal length of the lens? in cm.
Is the image in the previous question inverted or upright?
A. Inverted
B. Upright
C. Cannot tell from the information given.
The focal length of the lens is 24 cm. To find the focal length of the lens, we can use the lens formula:
1/f = 1/di - 1/do,
where f is the focal length of the lens, di is the image distance, and do is the object distance.
Given that the object distance (do) is 72 cm and the image distance (di) is 18 cm (since the image is virtual and formed on the same side as the object), we can substitute these values into the lens formula:
1/f = 1/18 - 1/72.
To solve for f, we can find the reciprocal of both sides:
f = 1 / (1/18 - 1/72).
Simplifying the expression on the right side:
f = 1 / (4/72 - 1/72) = 1 / (3/72) = 72 / 3 = 24 cm.
Therefore, the focal length of the lens is 24 cm.
Regarding the question of whether the image is inverted or upright, since the image is formed by a diverging lens and is virtual, it is always upright. Thus, the image in the previous question is upright (B. Upright).
To know more about The focal length
brainly.com/question/16188698
#SPJ11
Compare and contrast the following types of radiation, discussing their physical properties and shielding techniques: a) alpha and gamma radiation b) beta and beta radiation
Alpha and beta radiation have different physical properties and shielding techniques than gamma radiation. It is important to understand the differences between these types of radiation in order to protect ourselves and others from their harmful effects.
When comparing and contrasting alpha and gamma radiation, their physical properties and shielding techniques are two important aspects to consider. Alpha radiation consists of a helium nucleus with two protons and two neutrons, which means that it has a positive charge and a high ionizing ability. It is also relatively heavy and slow-moving, and can be stopped by a few sheets of paper or human skin.
On the other hand, gamma radiation is a high-energy photon that has no charge or mass, and it is able to penetrate most materials with ease. Gamma radiation can be shielded with materials that are dense and thick, such as lead or concrete.When comparing and contrasting beta and beta radiation, their physical properties and shielding techniques are also important.
Beta radiation consists of high-energy electrons that have a negative charge and a moderate ionizing ability. It is relatively light and fast-moving, and can penetrate materials such as aluminum and plastic. Beta radiation can be shielded with materials that are denser than air, such as aluminum or plastic.
Gamma radiation, like alpha radiation, is a high-energy photon that can penetrate most materials with ease. Gamma radiation can be shielded with materials that are dense and thick, such as lead or concrete.
In conclusion, alpha and beta radiation have different physical properties and shielding techniques than gamma radiation. It is important to understand the differences between these types of radiation in order to protect ourselves and others from their harmful effects.
Know more about radiation here,
https://brainly.com/question/31106159
#SPJ11
A proton has momentum 10⁻²⁰ Ns and the uncertainty in the position of the proton is 10⁻¹°m. What is the minimum fractional uncertainty in the momentum of this proton? A. 5 x 10⁻²⁵
B. 5 x 10⁻¹⁵ C. 5 x 10⁻⁵
D. 2 x 10⁴
A proton has momentum 10⁻²⁰ Ns and the uncertainty in the position of the proton is 10⁻¹°m. The minimum fractional uncertainty in the momentum of this proton is 5 x 10⁻²⁵.
The uncertainty principle states that the product of the uncertainty in the position of a particle and the uncertainty in its momentum is greater than or equal to Planck's constant divided by 2π. In this case, we have:
Δx × Δp >= ħ / 2π
where Δx is the uncertainty in the position of the proton, Δp is the uncertainty in the momentum of the proton, and ħ is Planck's constant.
We are given that Δx = 10⁻¹⁰m and ħ = 6.626 x 10⁻³⁴ Js. Plugging these values into the equation, we get:
(10⁻¹⁰m) × Δp >= 6.626 x 10⁻³⁴ Js / 2π
Solving for Δp, we get:
Δp >= 1.32 x 10⁻²⁵ kgm/s
The fractional uncertainty in the momentum is the uncertainty in the momentum divided by the momentum itself. In this case, the momentum of the proton is 10⁻²⁰ Ns. Therefore, the fractional uncertainty in the momentum is:
Δp / p = (1.32 x 10⁻²⁵ kgm/s) / (10⁻²⁰ Ns) = 5 x 10⁻²⁵
Therefore, the minimum fractional uncertainty in the momentum of this proton is 5 x 10⁻²⁵.
To learn more about uncertainty principle visit: https://brainly.com/question/11488878
#SPJ11
A ring of radius 4 with current 10 A is placed on the x-y plane with center at the origin, what is the circulation of the magnetic field around the edge of the surface defined by x=0, 3 ≤ y ≤ 5 and -5 ≤ z ≤ 2? OA 10 ов. 10 14 c. None of the given answers O D, Zero O E. 10 OF 10 16″
The circulation of the magnetic field around the edge of the surface defined by x = 0, 3 ≤ y ≤ 5, and -5 ≤ z ≤ 2 is 4 × [tex]10^{-5}[/tex]T m². Therefore, the correct answer is option (d) Zero.
Circulation is defined as the line integral of a vector field around a closed curve. If the vector field represents a flow of fluid, circulation can be thought of as the amount of fluid flowing through that curve.
Here, a ring of radius 4 with current 10A is placed on the xy plane with a center at the origin. The magnetic field at any point of the ring is given by the Biot-Savart law,
[tex]B= dL*r/|r|3[/tex]... (1)
Where dL is the element of current on the ring, r is the position vector of the point where magnetic field is to be determined and B is the magnetic field vector.
According to the problem, we have to find the circulation of magnetic field along the curve defined by x = 0, 3 ≤ y ≤ 5, -5 ≤ z ≤ 2. In the problem, the magnetic field is independent of y and z. Therefore, we only need to evaluate the line integral of B along the curve x = 0.
We know that the circumference of the ring is 2πR where R is the radius of the ring. Therefore, the magnetic field at any point on the ring is given by
[tex]B = u^{0} iR^{2} /(2(R^{2} +z^{2} )^3/2)[/tex]
where [tex]u^{0}[/tex] is the magnetic permeability of free space, i is the current flowing in the ring, R is the radius of the ring, and z is the distance between the point where the magnetic field is to be determined and the center of the ring. The value of [tex]u^{0}[/tex] is given as 4π × [tex]10^{-7}[/tex] T m/A.
Substituting the given values, we get B = 2 × [tex]10^{-5}[/tex] T.
Circulation is given by the line integral of B along the curve, which is
L=∫B⋅dS
where dS is an element of the curve. Since the curve is in the x = 0 plane, the direction of dS is along the y-axis. Therefore, dS = j dy where j is the unit vector along the y-axis.
Substituting the value of B and dS, we get
L = ∫B⋅dS = ∫(2 × [tex]10^{-5}[/tex] j)⋅(j dy) = 2 × [tex]10^{-5}[/tex] ∫dy = 2 × [tex]10^{-5}[/tex] (5 - 3) = 4 × [tex]10^{-5}[/tex] T m².
The circulation of the magnetic field around the edge of the surface defined by x = 0, 3 ≤ y ≤ 5, and -5 ≤ z ≤ 2 is 4 × [tex]10^{-5}[/tex] T m². Therefore, the correct answer is option (d) Zero.
Learn more about Biot-Savart law here:
https://brainly.com/question/30764718
#SPJ11
An object, located 80.0 cm from a concave lens, forms an image 39.6 cm from the lens on the same side as the object. What is the focal length of the lens?
a. -26.5 cm b. -120 cm c. -78.4 cm d. -80.8 cm e. -20.0 cm
The focal length of the concave lens is approximately -78.4 cm (option c).
To determine the focal length of the concave lens, we can use the lens formula : 1/f = 1/v - 1/u
where:
f is the focal length of the lens,
v is the image distance from the lens,
u is the object distance from the lens.
Given:
v = 39.6 cm (positive because the image is formed on the same side as the object)
u = -80.0 cm (negative because the object is located on the opposite side of the lens)
Substituting the values into the lens formula:
1/f = 1/39.6 - 1/(-80.0)
Simplifying the equation:
1/f = (80.0 - 39.6) / (39.6 * 80.0)
1/f = 40.4 / (39.6 * 80.0)
1/f = 0.01282
Taking the reciprocal of both sides:
f = 1 / 0.01282
f ≈ 78.011
Since the object is located on the opposite side of the lens, the focal length of the concave lens is negative.
Therefore, the focal length of the lens is approximately -78.4 cm (option c).
To learn more about concave lens :
https://brainly.com/question/2289939
#SPJ11
A cube sugar has a mass of 30g and occupies an area of 4cm2 with a height of 2cm. Calculate the density of the sugar.
Answer:
3.75 g/cm^3
Explanation:
The formula for density is mass divided by volume. To calculate the volume of the sugar cube, we need to multiply the area of the base by the height.
The area of the base is 4cm² and the height is 2cm, so the volume is:
Volume = Base Area x Height
Volume = 4cm² x 2cm
Volume = 8cm³
The mass of the sugar cube is 30g.
Now we can calculate the density of the sugar cube:
Density = Mass / Volume
Density = 30g / 8cm³
Density = 3.75 g/cm³
Therefore, the density of the sugar cube is 3.75 g/cm³.
Problem 4: A particle is moving to the right.
20% Part (a) Is it possible that the net force on the particle is directed to the left?
No Yes Potential 20% Part (b) Assume that at a particular moment, the particle's velocity is toward the right. Is it possible that the net force on the particle is directed downward (perpendicular to the particle’s velocity)?
20% Part (c) In general, the direction of the net force on a particle is always the same as the direction of its velocity.
20% Part (d) In general, the direction of the net force on a particle is always the same as the direction of its acceleration.
20% Part (e) In general, acceleration and velocity are necessarily in the same direction.
Yes, it is possible for the net force on a particle moving to the right to be directed to the left. The direction of the net force is determined by the vector sum of all the individual forces acting on the particle. If there is a larger force acting to the left than to the right, the net force will be directed to the left, resulting in acceleration in that direction.
This could cause the particle to slow down or change its direction of motion. Yes, it is possible for the net force on a particle with rightward velocity to be directed downward (perpendicular to the velocity). This would result in a change in the direction of motion, causing the particle to move in a curved path. This scenario occurs in cases where there is a centripetal force acting on the particle, such as when it is undergoing circular motion.
Part (c) In general, the direction of the net force on a particle is always the same as the direction of its velocity.
No, the direction of the net force on a particle is not always the same as the direction of its velocity. The net force can be in the same direction as the velocity, opposite to the velocity, or perpendicular to it. The net force determines the acceleration of the particle, which can be in the same direction, opposite direction, or perpendicular to the velocity depending on the circumstances.
Part (d) In general, the direction of the net force on a particle is always the same as the direction of its acceleration.
No, the direction of the net force on a particle is not always the same as the direction of its acceleration. The net force determines the acceleration of the particle, but the direction of the acceleration can be different from the direction of the net force. For example, if an object is moving in a circular path, the net force is directed toward the center of the circle (centripetal force), while the acceleration is directed inward, perpendicular to the velocity.
Part (e) In general, acceleration and velocity are necessarily in the same direction.
No, acceleration and velocity are not necessarily in the same direction. Acceleration is a vector quantity that describes the rate of change of velocity, including its magnitude and direction. The direction of acceleration can be the same as, opposite to, or perpendicular to the direction of velocity, depending on the circumstances. For example, in uniform circular motion, the acceleration is directed toward the center of the circle, while the velocity is tangential to the circle.
Learn more about force here:
https://brainly.com/question/30073908
#SPJ11
An FM radio station broadcasts at a frequency of 100 MHz. The period of this wave is closest to 10 ns 1 ns 10 us 100 ns
The period of the FM radio wave with a frequency of 100 MHz is closest to 10 ns.
The period of a wave is the time it takes for one complete cycle to occur. It is the reciprocal of the frequency. In this case, the FM radio station broadcasts at a frequency of 100 MHz, which means it undergoes 100 million cycles per second. To calculate the period, we divide 1 second by the frequency. In this case, the period is approximately 1/100 million seconds, which is equal to 10 ns (nanoseconds).
A nanosecond is one billionth of a second, and it represents a very short period of time. This short period is necessary for the FM radio wave to oscillate at such a high frequency. The wave completes one cycle every 10 ns, meaning it repeats its pattern 100 million times in one second. This rapid oscillation allows the transmission and reception of audio signals with high fidelity. Therefore, the period of the FM radio wave with a frequency of 100 MHz is closest to 10 ns.
Learn more about period of a FM radio wave:
https://brainly.com/question/28480049
#SPJ11
As a way of determining the inductance of a coil used in a research project, a student first connects the coil to a 12.0-V battery and measures a current of 0.630 A. The student then connects the coil to a 24.0-V (rms) 60.0-Hz generator and measures an rms current of 0.370 A.
a. Find the resistance of the coil.
b. Find the inductance of the coil.
As a way of determining the inductance of a coil used in a research project, a student first connects the coil to a 12.0-V battery and measures a current of 0.630. the resistance of the coil is approximately 19.05 Ω. and the inductance of the coil is approximately 0.575 H.
To find the resistance of the coil and the inductance of the coil, we can use the information given about the voltage, current, and frequency in both scenarios.
a. Finding the resistance of the coil:
Using Ohm's law, we know that resistance (R) is equal to the voltage (V) divided by the current (I):
R = V / I
In the first scenario, where the coil is connected to a 12.0-V battery and the current is 0.630 A, we can calculate the resistance:
R = 12.0 V / 0.630 A
R ≈ 19.05 Ω
Therefore, the resistance of the coil is approximately 19.05 Ω.
b. Finding the inductance of the coil:
To find the inductance (L) of the coil, we can use the relationship between inductance, frequency (f), and the rms current (I) in an AC circuit:
XL = (V / I) / (2πf)
Where XL is the inductive reactance.
In the second scenario, the coil is connected to a 24.0-V (rms) 60.0-Hz generator, and the rms current is 0.370 A. We can calculate the inductance:
XL = (24.0 V / 0.370 A) / (2π * 60.0 Hz)
XL ≈ 0.217 Ω
Since the inductive reactance (XL) is equal to the product of the inductance (L) and the angular frequency (ω), we can rearrange the equation to solve for the inductance:
L = XL / ω
Given that the angular frequency (ω) is 2πf, we can calculate the inductance:
L = 0.217 Ω / (2π * 60.0 Hz)
L ≈ 0.575 H
Therefore, the inductance of the coil is approximately 0.575 H.
Learn more about resistance here:
https://brainly.com/question/29427458
#SPJ11
Find solutions for your homework
science
earth sciences
earth sciences questions and answers
earth science: hydrology the diameter and depth of a cylindrical evaportation pan is 4.75 inches and 10 inches respectively. density of water is given as 997kg/m^3. using this information, solve the following problems. i. calculate the total volume (in m^3) and the cross sectional area (in m^2) of the pan. ii. if the pan contains 10 us gallons of
Question: Earth Science: Hydrology The Diameter And Depth Of A Cylindrical Evaportation Pan Is 4.75 Inches And 10 Inches Respectively. Density Of Water Is Given As 997kg/M^3. Using This Information, Solve The Following Problems. I. Calculate The Total Volume (In M^3) And The Cross Sectional Area (In M^2) Of The Pan. Ii. If The Pan Contains 10 US Gallons Of
Earth Science: Hydrology
The diameter and depth of a cylindrical evaportation pan is 4.75 inches and 10 inches respectively. Density of water is given as 997kg/m^3. Using this information, solve the following problems.
i. Calculate the total volume (in m^3) and the cross sectional area (in m^2) of the pan.
ii. If the pan contains 10 US gallons of water, calculate the depth of water in the pan in mm and the mass of water in the pan in kg.
iii. 9.25 gallons of water were left in the pan after it was left in a field (with 10 gallons of water) for 24hrs. Determine the average evaporation rate during this period in mm/hr.
The average evaporation rate during the 24 hours in millimeters per hour is 118 mm/hr.
i. Calculation of total volume (in m³) of the evaporation pan:
The diameter (d) of the cylindrical evaporation pan is 4.75 inches. The radius (r) can be calculated as half the diameter, which is 2.375 inches. Converting the radius to meters using the conversion factor of 1m = 39.3701 inches, we get 2.375 inches
= 2.375/39.3701 m
= 0.0604 m.
The depth of the pan (h) is given as 10 inches, which converts to 10/39.3701 m
= 0.254 m.
The cross-sectional area of the cylindrical pan can be calculated using the formula: πr². Substituting the values, we have π(0.0604 m)²
= 0.0115 m².
The volume of the pan is obtained by multiplying the cross-sectional area by the depth of the pan: 0.0115 m² x 0.254 m = 0.0029 m³.
Therefore, the total volume of the evaporation pan is 0.0029 m³.
ii. If the evaporation pan contains 10 US gallons of water:
To calculate the volume of the evaporation pan, we need to convert the volume from US gallons to cubic meters. One US gallon is equivalent to 3.78541 liters. Therefore,
10 US gallons = 10 x 3.78541 liters
= 37.8541 liters.
Converting liters to cubic centimeters, we have 37.8541 liters = 37.8541 x 1000 cm³ = 37854.1 cm³. To convert cubic centimeters to cubic meters, we divide by 1000000: 37854.1 cm³ = 0.0378541 m³.
The depth of water in the pan can be calculated by dividing the volume of water by the area of the evaporation pan: 0.0378541 m³ / 0.0115 m² = 3.29 m.
To convert meters to millimeters, we multiply by 1000: 3.29 m = 3290 mm.
Therefore, the depth of water in the evaporation pan is 3290 mm.
The mass of water in the evaporation pan can be calculated using the density of water, which is 997 kg/m³. The mass (m) is obtained by multiplying the density by the volume: 997 kg/m³ x 0.0378541 m³ = 2.89 kg.
iii. Calculation of the average evaporation rate during the 24 hours:
The initial volume of water in the pan is 10 US gallons, which is equivalent to 37.8541 liters = 0.0378541 m³.
The volume of water left in the pan after 24 hours is given as 9.25 US gallons. Converting to cubic meters, we have
9.25 x 3.78541 liters
= 35.0189 liters
= 35.0189 x 1000 cm³
= 35018.9 cm³
= 0.0350189 m³.
The volume of water evaporated is obtained by subtracting the final volume from the initial volume:
0.0378541 m³ - 0.0350189 m³ = 0.0028352 m³.
The average evaporation rate during the 24 hours is calculated by dividing the volume of water evaporated by the time:
0.0028352 m³ / 24 hours
= 0.000118 m³/h.
To convert cubic meters per hour to cubic millimeters per hour, we multiply by 1000000000: 1 m³/h = 1000000000 mm³/h.
Therefore, the average evaporation rate during the 24 hours in millimeters per hour is 118 mm/hr.
Learn more about evaporation rate
https://brainly.com/question/30686439
#SPJ11
A rope, clamped at both ends, is 190 cm in length. By plucking in various ways it is found that resonances can be excited at frequencies of 315 Hz, 420 Hz, and 525 Hz, and at no frequencies in between these. At what speed do waves travel on this rope?
At the speed of 1197 m / s the waves travel on this rope.
To find the speed of waves on the rope, we can use the formula:
v = f * λ
where v is the speed of waves, f is the frequency, and λ is the wavelength.
Since the rope is clamped at both ends, it forms a standing wave pattern. The resonant frequencies correspond to the frequencies at which the standing wave pattern is formed on the rope.
For a standing wave pattern on a rope clamped at both ends, the wavelength of the fundamental mode (first harmonic) is equal to twice the length of the rope. Therefore, the wavelength of the fundamental mode, λ1, is:
λ1 = 2 * 190 cm
Now, we can calculate the speed of waves on the rope using the fundamental frequency, f1, and the wavelength of the fundamental mode, λ1:
v = f1 * λ1
Substituting the values, we have:
v = 315 Hz * 2 * 190 cm = 1197 m / s.
To know more about wavelength
https://brainly.com/question/32680147
#SPJ11
An open switch is conneced in series to a circuit loop that already has three elements connected in series, a battery (ε = 120 V), an ideal inductor (L = 10 H), and a resistor (R = 1012). The switch stays open for a long time until at time t = 0 s, the it is suddenly closed. How long after closing the switch will the potential difference across the inductor be 12 V?
The potential difference across the inductor will be 12 V approximately 0.074 seconds after closing the switch.
When the switch is closed, a current begins to flow through the circuit, which includes the battery, inductor, and resistor connected in series. Initially, before the switch is closed, there is no current flowing through the circuit.
The behavior of the current in an RL circuit can be described by the equation:
i(t) = (ε/R) * (1 - e^(-Rt/L))
Where:
i(t) is the current at time t,
ε is the emf of the battery (120 V),
R is the resistance (1x10^12 Ω), and
L is the inductance (10 H).
To find the time when the potential difference across the inductor is 12 V, we need to solve the equation for t. Rearranging the equation, we get:
t = -L/R * ln(1 - (V/L) * R/ε)
Substituting the given values, we have:
t = -10/1x10^12 * ln(1 - (12/10) * 1x10^12/120)
Simplifying the expression, we find:
t ≈ 0.074 seconds
Therefore, approximately 0.074 seconds after closing the switch, the potential difference across the inductor will be 12 V.
Learn more about resistance here:
brainly.com/question/29427458
#SPJ11
The electrical resistivity of a sample of copper at 300 K is 1.0 micro Ohm.cm. Find the relaxation time of free electrons in copper, given that each copper atom contributes one free electron. The density of copper is 8.96 gm/cm³.
The electrical resistivity of a sample of copper at 300 K is 1.0 micro Ohm.cm. The density of copper is 8.96 gm/cm³. Each copper atom contributes one free electron. The relaxation time of free electrons in copper is 3.57× 10⁻¹⁴ seconds.
Electrical resistivity (ρ) of the material is given by;$$\rho = \frac{m}{ne^2\tau}$$ Where, m = Mass of the electron = Number of electrons per unit volume (or density of free electron) e = Charge on an electron$$\tau = \text{relaxation time of the free electrons}$$Rearranging the above formula, we get;$$\tau = \frac{m}{ne^2\rho}$$We know that, density of copper (ρ) = 8.96 gm/cm³ = 8960 kg/m³Resistivity of copper (ρ) = 1.0 × 10⁻⁶ ohm cm, Charge on an electron (e) = 1.6 × 10⁻¹⁹ C Number of free electrons per unit volume of copper, n = The number of free electrons contributed by each copper atom = 1. Mass of an electron (m) = 9.1 × 10⁻³¹ kg. Putting the above values in the equation of relaxation time of free electrons in copper, we get;$$\tau = \frac{9.1 × 10^{-31}}{(1)(1.6 × 10^{-19})^2(1.0 × 10^{-6})}$$$$\tau = 3.57 × 10^{-14}\ seconds$$. Therefore, the relaxation time of free electrons in copper is 3.57 × 10⁻¹⁴ seconds.
Learn more about electrical resistivity:
https://brainly.com/question/13735984
#SPJ11
For crystal diffraction experiments, wavelengths on the order of 0.20 nm are often appropriate, since this is the approximate spacing between atoms in a solid. Find the energy in eV for a particle with this wavelength if the particle is (a) a photon, (b) an electron, (c) an alpha particle (mc² = 3727 MeV).
a. The energy of a photon is 62.1 eV.
b. The energy of an electron is 227.8 eV.
c. The energy of an alpha particle is 2.33 x 10²⁷ eV
a. Energy of a photon:
E = hc/λ
where,
h = Planck's constant = 6.626 x 10⁻³⁴ J-s
c = speed of light = 3 x 10⁸ m/s
λ = wavelength of photon
E = (6.626 x 10⁻³⁴ J-s) x (3 x 10⁸ m/s) / (0.20 x 10⁻⁹ m)
= 9.939 x 10⁻¹² J
Convert J to eV by dividing by 1.6 x 10⁻¹⁹ J/eV,
E = (9.939 x 10⁻¹² J) / (1.6 x 10⁻¹⁹ J/eV)
≈ 62.1 eV
Therefore, the energy of a photon with this wavelength is 62.1 eV.
b. Energy of an electron:
E = p²/2m
where,
p = momentum of electron
m = mass of electron = 9.1 x 10⁻³¹ kg
λ = h/p
p = h/λ
E = h²/2m
λ²= (6.626 x 10⁻³⁴ J-s)² / [2 x (9.1 x 10⁻³¹ kg) x (0.20 x 10⁻⁹ m)²]
= 3.648 x 10⁻¹⁰ J
Convert J to eV by dividing by 1.6 x 10⁻¹⁹ J/eV,
E = (3.648 x 10⁻¹⁰ J) / (1.6 x 10⁻¹⁹ J/eV)
≈ 227.8 eV
Therefore, the energy of an electron with this wavelength is 227.8 eV.
c. Energy of an alpha particle:
E = mc² / √(1 - v²/c²)
where,
m = mass of alpha particle
c = speed of light = 3 x 10⁸ m/s
λ = h/p
p = h/λ
v = p/m
= (h/λ)/(mc)
= h/(λmc)
E = mc² / √(1 - v²/c²)
E = (3727 MeV) x (1.6 x 10⁻¹³ J/MeV) / √(1 - (6.626 x 10⁻³⁴ J-s/(0.20 x 10⁻⁹ m x 3727 x 1.67 x 10⁻²⁷ kg x (3 x 10⁸ m/s))²))
≈ 3.72 x 10¹³ J
Convert J to eV by dividing by 1.6 x 10⁻¹⁹ J/eV,
E = (3.72 x 10¹³ J) / (1.6 x 10⁻¹⁹ J/eV)
≈ 2.33 x 10²⁷ eV
Therefore, the energy of an alpha particle with this wavelength is 2.33 x 10²⁷ eV.
Learn more about the alpha particle:
brainly.com/question/22799756
#SPJ11
Suppose the measured AC voltage between two terminals is 8.2 V.
What is the real peak voltage?
A.
23.2 V
B.
20.4 V
C.
26.0 V
D.
None of these answers.
E.
17.5 V
The correct option is D) none of these answers.
AC voltage:
AC stands for Alternating Current Voltage. It is the rate at which electric charge changes direction in a circuit. The direction of current flow changes constantly, usually many times per second.
AC voltage is calculated by measuring the amplitude of the wave from its crest to its trough. The peak voltage is the highest voltage in a circuit that occurs at any given time.
AC Voltage is usually measured in RMS or Root Mean Square. Let's find out the real peak voltage.
The formula for peak voltage (Vp) is given as
Vp = Vrms * √2
Given, Vrms = 8.2 V
Therefore, Vp = 8.2 * √2= 11.6 V
So, the real peak voltage is 11.6V.
Therefore, the correct option is D) none of these answers.
learn more about AC voltage here:
https://brainly.com/question/13507291?referrer=searchResults
#SPJ11
Can I use both multiplexer and demultiplexer in one circuit? Explain. Please provide a diagram.
Yes, it is possible to use both a multiplexer and a demultiplexer in one circuit. A multiplexer (MUX) is a digital circuit that combines multiple input signals into a single output, based on the control inputs.
On the other hand, a demultiplexer (DEMUX) does the opposite, taking a single input and routing it to one of several outputs, again based on the control inputs.
By combining a MUX and a DEMUX, we can create a circuit that performs bidirectional data transmission or routing. The MUX can be used to select the input signal, while the DEMUX can be used to select the output for that signal. This can be useful in scenarios where data needs to be transmitted or routed in both directions, such as in communication systems, data buses, or multiprocessor systems. By using both a MUX and a DEMUX together, we can effectively manage and control the flow of data in a more flexible manner within a circuit.
To know more about multiplexer, here
brainly.com/question/15052768
#SPJ4
A 225kg floor safe is being moved by thief-cats 8.5 m from its initial location. One thief pushes 12.0N at an angle of 30 ° downward and another pulls with 10.0N at an angle of 40 ° upward. What is the net work done by the thieves on the safe? How much work is done by the gravitational force and the normal force? If the safe was initially at rest, what is the speed at the end of the 8.5 m displacement?
The net work done by the thieves on the safe is 173.644 Joules, the work done by the gravitational force is -17364 Joules, and the normal force does no work.
The final speed of the safe at the end of the 8.5 m displacement is approximately 2.29 m/s.
To solve this problem, we need to calculate the net work done by the thieves, the work done by the gravitational force, and the work done by the normal force. We can then use the work-energy theorem to find the final speed of the safe.
1. Net Work Done by the Thieves:
The net work done by the thieves can be calculated by adding the work done by each thief. The work done by a force is given by the equation: work = force * displacement * cos(angle).
Thief 1:
Force = 12.0 N
Displacement = 8.5 m
Angle = 30°
Work1 = 12.0 N * 8.5 m * cos(30°)
Thief 2:
Force = 10.0 N
Displacement = 8.5 m
Angle = 40°
Work2 = 10.0 N * 8.5 m * cos(40°)
Net Work Done by the Thieves = Work1 + Work2
2. Work Done by the Gravitational Force:
The work done by the gravitational force can be calculated using the equation: work = force * displacement * cos(angle).
Force (weight) = mass * gravitational acceleration
mass = 225 kg
gravitational acceleration = 9.8 m/s² (approximate value on Earth)
Displacement = 8.5 m
Angle = 180° (opposite direction of displacement)
Work done by the gravitational force = (225 kg * 9.8 m/s²) * 8.5 m * cos(180°)
3. Work Done by the Normal Force:
Since the safe is on a flat surface and not accelerating vertically, the normal force does no work. The normal force is perpendicular to the displacement, so the angle between them is 90°, and cos(90°) = 0.
Work done by the normal force = 0
4. Final Speed of the Safe:
We can use the work-energy theorem to find the final speed of the safe. The work-energy theorem states that the net work done on an object is equal to its change in kinetic energy.
Net Work Done by the Thieves = Change in Kinetic Energy
Since the safe was initially at rest, the initial kinetic energy is zero. Therefore, the net work done by the thieves is equal to the final kinetic energy.
Net Work Done by the Thieves = (1/2) * mass * final speed^2
We can solve this equation for the final speed:
(1/2) * mass * final speed² = Net Work Done by the Thieves
final speed² = (2 * Net Work Done by the Thieves) / mass
final speed = √((2 * Net Work Done by the Thieves) / mass)
Now, let's calculate the values:
1. Net Work Done by the Thieves:
Work1 = 12.0 N * 8.5 m * cos(30°)
Work2 = 10.0 N * 8.5 m * cos(40°)
Net Work Done by the Thieves = Work1 + Work2
2. Work Done by the Gravitational Force:
Work done by the gravitational force = (225 kg * 9.8 m/s²) * 8.5 m * cos(180°)
3. Work Done by the Normal Force:
Work done by the normal force = 0
4. Final Speed of the Safe:
final speed = √((2 * Net Work Done by the Thieves) / mass)
Now, let's calculate these values:
Calculations:
Work1 = 12.0 N * 8.5 m * cos(30°) = 102.180 J
Work2 = 10.0 N * 8.5 m * cos(40°) = 71.464 J
Net Work Done by the Thieves = Work1 + Work2 = 173.644 J
Work done by the gravitational force = (225 kg * 9.8 m/s^2) * 8.5 m * cos(180°) = -17364 J (negative sign indicates work done against the gravitational force)
Work done by the normal force = 0 J
final speed = √((2 * Net Work Done by the Thieves) / mass) = sqrt((2 * 173.644 J) / 225 kg) = 2.29 m/s (approximately)
Therefore, the net work done by the thieves on the safe is 173.644 Joules, the work done by the gravitational force is -17364 Joules, and the normal force does no work. The final speed of the safe at the end of the 8.5 m displacement is approximately 2.29 m/s.
To learn more about gravitational force visit:
brainly.com/question/32609171
#SPJ11
An unstable high-energy particle enters a detector and leaves a track 0.855 mm long before it decays. Its speed relative to the detector was 0.927c. What is its proper lifetime in seconds? That is, how long would the particle have lasted before decay had it been at rest with respect to the detector? Number ___________ Units _______________
The proper lifetime of the particle have lasted before decay had it been at rest with respect to the detector is 3.101 × 10⁻¹⁶ s. That is, Number 3.101 × 10⁻¹⁶ Units seconds.
It is given that, Length of track, l = 0.855 mm, Speed of the particle relative to the detector, v = 0.927c.
Let's calculate the proper lifetime of the particle using the length of track and speed of the particle.To calculate the proper lifetime of the particle, we use the formula,
[tex]\[\tau =\frac{l}{v}\][/tex] Where,τ = Proper lifetime of the particle, l = Length of the track and v = Speed of the particle relative to the detector
Substituting the values, we get:
τ = l / v = 0.855 mm / 0.927 c
To solve this equation, we need to use some of the conversion factors:
1 c = 3 × 10⁸ m/s
1 mm = 10⁻³ m
So, substituting the above values in the above equation, we get,
τ = (0.855 × 10⁻³ m) / (0.927 × 3 × 10⁸ m/s)
τ = 3.101 × 10⁻¹⁶ s
Hence, the proper lifetime of the particle is 3.101 × 10⁻¹⁶ s (seconds).
To learn more about speed: https://brainly.com/question/13943409
#SPJ11
A beam of light in air is incident on the surface of a rectangular block of clear plastic (n = 1.49). If the velocity of the beam before it enters the plastic is 3.00E+8 m/s, what is its velocity inside the block? a. 3.00E+8 m/s b. 1.35E+8 m/s
c. 2.01E+8 m/s d. 2.46E+8 m/s
A beam of light in air is incident on the surface of a rectangular block of clear plastic (n = 1.49). If the velocity of the beam before it enters the plastic is 3.00E+8 m/s the velocity inside the block can be calculated as follows:
`n = c/v` where c is the velocity of light in a vacuum and v is the velocity of light in the medium. The velocity of light in the medium is calculated using `v = c/n`.
Therefore, `v = 3.00E+8 m/s / 1.49 = 2.01E+8 m/s`.
Hence, the velocity of the beam inside the block is 2.01E+8 m/s, and the answer is option (c) 2.01E+8 m/s.
Learn more about light incident on various media: https://brainly.com/question/15838784
#SPJ11
A monatomic ideal gas starts at a volume of 3L, and 75 kPa. It is compressed isothermally until its pressure is 200 kPa. Determine the amount of work done, the amount of heat that flows, and the change in internal energy of the gas. Also indicate the direction (into or out of the gas) for the work and the heat.
during the isothermal compression of the monatomic ideal gas from 3L and 75 kPa to 200 kPa, the gas does not undergo any change in internal energy. The work done on the gas is -213 J, indicating compression, and the same amount of heat flows into the gas.
In an isothermal process, the temperature of the gas remains constant. The work done by an ideal gas during an isothermal process can be calculated using the formula:Work = nRT ln(V2/V1),where n is the number of moles of the gas, R is the ideal gas constant, T is the temperature, and V1 and V2 are the initial and final volumes, respectively.
Since the gas is monatomic, its internal energy is solely dependent on its temperature, given by the equation:Internal energy = (3/2) nRT,where (3/2) nRT represents the average kinetic energy of the gas particles.Since the process is isothermal, the change in internal energy is zero. Therefore, the heat flow into the gas is equal to the amount of work done, which is -213 J.
The negative sign indicates that work is done on the gas. Therefore ,during the isothermal compression of the monatomic ideal gas from 3L and 75 kPa to 200 kPa, the gas does not undergo any change in internal energy. The work done on the gas is -213 J, indicating compression, and the same amount of heat flows into the gas.
Learn more about isothermal here:
https://brainly.com/question/32558407
#SPJ11
Given a three-phase AC power network with a load, which consumes 100 MW with a power factor of 0.8 (lagging). Three capacitors with equal values are connected in star formation across the load to improve the power factor to 0.96 (leading). Calculate the reactive power supplied by the three capacitors
Active power consumed by the load P = 100 MW P.F of the load cos φ = 0.8 (lagging)
P.F of the load after connecting capacitors cos φ2 = 0.96 (leading)
The formula to calculate the reactive power is
Q = P(tan φ1 - tan φ2) Where, Q = Reactive power required by capacitors P = Active power consumed by the load
cos φ1 = Power factor of the load before adding capacitors
cos φ2 = Power factor of the load after adding capacitors
tan φ1 = √(1 - cos²φ1)/cos φ1
tan φ1 = √(1 - 0.8²)/0.8 = 0.6
tan φ2 = √(1 - cos²φ2)/cos φ2
tan φ2 = √(1 - 0.96²)/0.96 = 0.4
Therefore, Q = 100 × (0.6 - 0.4) = 20 MW
Thus, the reactive power supplied by the three capacitors is 20 MW.
Read up more about capacitors: https://brainly.com/question/21851402
#SPJ11
Two particles are fixed to an x axis: particle 1 of charge q₁ = 3.00 × 10⁻⁸ C at x = 22.0 cm and particle 2 of charge q₂ = −5.29q₁ at x = 69.0 cm. At what coordinate on the x axis is the electric field produced by the particles equal to zero?
The coordinate on the x-axis where the electric field is zero is 44.4 cm.
Particle 1 of charge q₁ = 3.00 × 10⁻⁸ C at x = 22.0 cm
Particle 2 of charge q₂ = −5.29q₁ at x = 69.0 cm.
The formula to calculate electric field due to a point charge is given by:
E = kq/r²
Here,
E is the electric field,
q is the charge on the particle,
r is the distance between the two points
k is the Coulomb constant k = 9 × 10^9 N·m²/C².
For two point charges, the electric field is given by:
E = kq₁/r₁² + kq₂/r₂²,
where r₁ and r₂ are the distances from the point P to each charge q₁ and q₂ respectively.
Using this formula,
The electric field due to particle 1 at point P is given by:
E₁ = kq₁/r₁²
The electric field due to particle 2 at point P is given by:
E₂ = kq₂/r₂²
Now we have, E₁ = -E₂, for the net electric field to be zero.
So,
kq₁/r₁² = kq₂/r₂²
q₂/q₁ = 5.29
The distance of the point P from the charge q₁ is (69 - x) cm.
The distance of the point P from the charge q₂ is (x - 22) cm.
Then, applying the formula, we have:
kq₁/(69 - x)² = kq₂/(x - 22)²
q₂/q₁ = 5.29
kq₁/(69 - x)² = k(-5.29q₁)/(x - 22)²
1/(69 - x)² = -5.29/(x - 22)²
(69 - x)² = 5.29(x - 22)²
Solving this equation, we get:
x = 44.4 cm (approx)
Therefore, the coordinate on the x-axis where the electric field is zero is 44.4 cm.
Learn more about the electric field:
brainly.com/question/19878202
#SPJ11
A perfect fixed mass of gas slowly follows the evolutions in the Figure below.1) Which of these developments is at constant temperature (isothermal)?
2) What evolution is at constant volume (isochore)
The development at constant temperature (isothermal) is B-C, and the development at constant volume (isochore) is D-E.
The development at constant temperature (isothermal) is B-C. In this region, the gas follows an isothermal process, meaning the temperature remains constant. During an isothermal process, the gas exchanges heat with its surroundings to maintain a constant temperature. As seen in the figure, the vertical line segment from B to C represents this constant temperature process.
The evolution at constant volume (isochore) is D-E. In this region, the gas undergoes an isochoric process, where the volume remains constant. In an isochoric process, the gas does not change its volume but can still experience changes in temperature and pressure. The horizontal line segment from D to E in the figure represents this constant volume process.
Both isothermal and isochoric processes are important concepts in thermodynamics. Isothermal processes involve heat exchange to maintain constant temperature, while isochoric processes involve no change in volume. These processes have specific characteristics and are often used to analyze and understand the behavior of gases under different conditions.
Learn more about isothermal and isochore processes:
https://brainly.com/question/13281279
#SPJ11
In complex electric power system, please give the basic description about the control of voltage and reactive power. 6) The typical short circuits faults happened in power system, please give the typical types.
In complex electric power systems, the voltage and reactive power are controlled using various devices and techniques.
The control of voltage and reactive power is necessary to maintain the system's stability and ensure reliable power supply to the loads. In general, there are two ways to control the voltage and reactive power of a power system: through the use of automatic voltage regulators (AVRs) and reactive power compensation devices.
AVRs are used to regulate the voltage at the load buses and maintain the voltage within an acceptable range. These devices work by automatically adjusting the excitation level of the generator to compensate for changes in load demand or system conditions. Reactive power compensation devices, such as capacitors and reactors, are used to control the flow of reactive power in the system. These devices are used to reduce voltage drops, improve power factor, and increase the system's stability.
In a power system, short circuits can occur due to various reasons such as equipment failure, lightning strikes, and human error. The typical types of short circuit faults that occur in power systems are:
1. Three-phase faults: These occur when all three phases of the system short circuit to each other or to ground. This type of fault is the most severe and can cause extensive damage to equipment and the system.
2. Single-phase faults: These occur when a single phase of the system short circuits to another phase or to ground. This type of fault is less severe than three-phase faults but can still cause significant damage.
3. Double-phase faults: These occur when two phases of the system short circuit to each other. This type of fault is less common but can still cause damage to equipment and the system.
In conclusion, the control of voltage and reactive power is essential in complex electric power systems. The use of AVRs and reactive power compensation devices helps maintain system stability and reliable power supply. Short circuits faults in power systems can occur due to various reasons, and the most typical types are three-phase faults, single-phase faults, and double-phase faults.
Learn more about short circuit faults here:
https://brainly.com/question/4525793
#SPJ11
Max Planck proposed that a blackbody is made up of tiny oscillators. True False Question 6 Which of the following statements is FALSE about the experimental observations of blackbody radiation? There exists a peak wavelength with the largest amount of intensity. The intensity of the wavelengths lessens the further away from the peak wavelength you are. There is no relationship between the temperature of the blackbody and its peak frequency. The hotter the blackbody, the less the peak wavelength.
The statement that is FALSE is that there is no relationship between the temperature of the blackbody and its peak frequency. A decrease in temperature leads to a decrease in peak frequency and an increase in wavelength. The converse is also true.
Max Planck proposed that a blackbody is made up of tiny oscillators, and this is true. A blackbody refers to an object that absorbs all the radiation that falls on it, without reflecting anything. An oscillator, in this case, refers to any entity that oscillates or vibrates in a regular manner. Blackbodies are made up of tiny oscillators, and each oscillator may only oscillate at a particular frequency. Planck assumed that the amount of energy a blackbody emitted was a product of the frequency of the oscillator and a constant (h), which came to be known as Planck's constant.
This assumption led to the discovery of the quantum mechanics theory.False - there is no relationship between the temperature of the blackbody and its peak frequency. The observations of blackbody radiation are concerned with the wavelength emitted by a blackbody. As the temperature of a blackbody is increased, the wavelength emitted shifts to shorter wavelengths. Therefore, the hotter the blackbody, the less the peak wavelength. Also, experimental observations show that there exists a peak wavelength with the largest amount of intensity.
The intensity of the wavelengths lessens the further away from the peak wavelength you are. Therefore, the statement that is FALSE is that there is no relationship between the temperature of the blackbody and its peak frequency. A decrease in temperature leads to a decrease in peak frequency and an increase in wavelength. The converse is also true.
Learn more about frequency here,
https://brainly.com/question/254161
#SPJ11
if you were to observe a source with a visible wavelength that
is in orange part of spectrum, what happens to the color of light
as you move towards the source? how would the shape of wave
change?
1.) The color of light would appear to shift towards the orange end of the spectrum as you move towards the source.
2.) The shape of the wave would not change
1.) If you were to observe a source with a visible wavelength in the orange part of the spectrum, you would notice that the color of light appears to shift towards the orange end of the spectrum as you move towards the source. This shift in color is a result of the Doppler effect, a phenomenon where the apparent frequency of sound or light waves changes when the source and the observer are in relative motion. It's important to note that the shape of the wave remains unchanged during this process.
2.) In the case of sound waves, let's consider an approaching ambulance with a siren. As the ambulance moves closer to you, the frequency of the sound waves increases, causing a higher pitch. Conversely, as the ambulance moves away from you, the frequency of the sound waves decreases, resulting in a lower pitch. This same principle applies to light waves, although the Doppler effect is more noticeable for sound waves due to their lower velocity compared to light waves.
To summarize, as you move towards a source emitting visible light in the orange part of the spectrum, the color of light will appear to shift towards orange. The shape of the wave remains the same, but the wavelength decreases, leading to an increase in frequency.
Learn more about the Doppler effect:
https://brainly.com/question/28106478
#SPJ11
Two point changes 25 cm agat have an electnc Part A potential enerpy +150 is The toeal charge is 20 nC What ike the two charges? Express your answers using two significant figures. Enteryour answers numeticaliy separated by commas.
Given: Potential Energy, U = +150 V, separation distance, r = 25 cm = 0.25 m, and Total charge, Q = 20 nC.To find: Find the two charges, q1 and q2.
Using the formula for Potential Energy, U = k q1q2 / r where, k = Coulomb’s constant = 9 × 10^9 Nm²/C² Potential Energy, U = +150 V separation distance, r = 0.25 m.
Therefore, we get:150 = (9 × 10^9) q1q2 / 0.25q1q2 = (150 × 0.25) / (9 × 10^9)q1q2 = 4.17 × 10^-6 C²Total charge, Q = 20 nCq1 + q2 = Qq1 = Q - q2q1 = 20 × 10^-9 C - 4.17 × 10^-6 Cq1 = -4.168 × 10^-6 C (Approximately equals to -4.2 × 10^-6 C)q2 = 4.17 × 10^-6 C (Approximately equals to 4.2 × 10^-6 C)Therefore, the charges are approximately equals to -4.2 × 10^-6 C and 4.2 × 10^-6 C.
Learn more on Potential energy here:
brainly.in/question/26640823
#SPJ11
An atom of $Be iss at rest, minding its own business, when suddenly it decays into He + He, that is two alpha particles. Find the kinetic energy of each of these He has an atomic mass of 4.002603 u, and Be has an atomic mass of 8.005305 u. Report your answer in keV, rounded to zero decimal places
Answer:
The kinetic energy of He has an atomic mass of 4.002603 u, and Be has an atomic mass of 8.005305 u is 1.329288keV
Mass of helium atom (He) = 4.002603 u
Mass of beryllium atom (Be) = 8.005305 u
Since the beryllium atom is initially at rest, the total momentum before the decay is zero. Therefore, the total momentum after the decay must also be zero to satisfy the conservation of momentum.
Let's denote the kinetic energy of each helium atom as KE_He1 and KE_He2.
After the decay, the two helium atoms move in opposite directions with equal and opposite momenta. This means their momenta cancel out, resulting in a total momentum of zero.
The momentum of an object is given by the equation:
p = mv
Since the total momentum is zero, the sum of the momenta of the two helium atoms must also be zero:
p_He1 + p_He2 = 0
Using the momentum equation, we have:
(m_He1 * v_He1) + (m_He2 * v_He2) = 0
Since the masses of the helium atoms are the same (m_He1 = m_He2), we can rewrite the equation as:
m_He * (v_He1 + v_He2) = 0
Since the masses are positive, the velocities must be equal in magnitude but opposite in direction:
v_He1 = -v_He2
Now, let's calculate the kinetic energy of each helium atom:
KE_He1 = (1/2) * m_He * (v_He1)^2
KE_He2 = (1/2) * m_He * (v_He2)^2
Since the velocities are equal in magnitude but opposite in direction, their squares are equal:
(v_He1)^2 = (v_He2)^2 = v^2
Therefore, the kinetic energy of each helium atom can be written as:
KE_He1 = KE_He2 = (1/2) * m_He * v^2
Now, let's substitute the values:
m_He = 4.002603 u
v is the velocity of each helium atom after the decay, which we need to determine.
To convert the mass from atomic mass units (u) to kilograms (kg), we use the conversion factor:
1 u = 1.66053906660 x 10^(-27) kg
m_He = 4.002603 u * (1.66053906660 x 10^(-27) kg/u)
= 6.6446573353 x 10^(-27) kg
To find the velocity of the helium atoms, we need to consider the conservation of energy. The total energy before the decay is the rest energy of the beryllium atom, which is given by:
E_total = m_Be * c^2
The total energy after the decay is the sum of the kinetic energies of the helium atoms:
E_total = 2 * KE_He
Setting these two expressions for total energy equal to each other, we have:
m_Be * c^2 = 2 * (1/2) * m_He * v^2
Simplifying the equation:
v^2 = (m_Be * c^2) / (2 * m_He)
Now, we substitute the values:
m_Be = 8.005305 u * (1.66053906660 x 10^(-27) kg/u) = 1.329288
Therefore, The kinetic energy of He has an atomic mass of 4.002603 u, and Be has an atomic mass of 8.005305 u is 1.329288keV
Learn more about kinetic energy, here
https://brainly.com/question/30337295
#SPJ11