I =1000 x s [ square root of three x v]
Explanation:
Answer:
To calculate full load current, divide the full load power by the product of the full load voltage times 1.723
Construction engineering differs from other types of civil engineering because it focuses on supervising the creation of the building as well as design.
O A True
O B.False
Answer:
A. True
Construction engineering focuses on managing the construction process of buildings and infrastructure projects, which involves supervising the creation of the building as well as the design. Construction engineers oversee the construction site, coordinate with different stakeholders, manage the budget, and ensure that the project is completed on time, on budget, and according to the specifications.
Problem 2
A 1000-VA, 230/115-V transformer has been tested to determine its equivalent circuit. The results are:
Open-Circuit Test (on LV Side): VOC = 115 V, IOC = 0.11 A, POC = 3.9 W.
Short-Circuit Test (on HV Side): VSC = 17.1 V, ISC = 8.7 A, PSC = 38.1 W.
a) Find the equivalent circuit of this transformer referred to the low-voltage side of the transformer.
b) Find the voltage regulation at rated condition and (i) 0.8 lagging (ii) 1.0 (iii) 0.8 leading power factors.
c) Determine the transformer’s efficiency at rated condition and 0.8 lagging power factor.
Answer
The values of the series impedance (Zeq) and the shunt admittance must be determined in order to identify the equivalent circuit referred to as the low-voltage side (Yeq).
Initially, using data from the short-circuit test, we can compute the equivalent resistance and reactance in the HV side:
Rsc=Vsc/ISC=17.1 V/8.5 A =1.965 ohms
ISC = sqrt(38.12 - 1.9652) / 8.7 A = 4.588 ohms, where Xsc = sqrt(Psc2 - Rsc2)
Following that, we can get the series impedance for the low-voltage side:
Zeq is equal to ((VOC / IOC) - Rsc) / ((IOC / ISC) - 1) = ((115 V / 0.11 A) - 1.965 ohms) / ((0.11 A / 8.7 A) - 1) = 2.904 + j4.508 ohms.
Last but not least, we may determine the shunt admittance for the low-voltage side:
Yeq is equal to (IOC - ISC* Zeq / (Zeq2 + Rsc2)). (2.904 + j4.508) ohms / (2.904 + j4.508)2 + 1.965 ohms / (0.11 A - 8.7 A * (2.904 + j4.508) ohms) / VOC
To locate the equivalent circuit known as the low-voltage side, the series impedance (Zeq) and shunt admittance values must be established (Yeq).
To begin with, we may calculate the equivalent resistance and reactance in the HV side using the results from the short-circuit test:
Rsc = Vsc / ISC = 17.1 V / 8.5 A = 1.965 ohms
Where Xsc = sqrt and ISC = sqrt(38.12 - 1.9652) / 8.7 A = 4.588 ohms (Psc2 - Rsc2)
The series impedance for the low-voltage side is therefore obtained as follows:
((VOC / IOC) - Rsc) / ((IOC / ISC) - 1) = ((115 V / 0.11 A) - 1.965 ohms) / ((0.11 A / 8.7 A) - 1) = 2.904 + j4.508 ohms is the formula for Zeq.
The voltage drop at full load may be calculated using the equivalent impedance as follows:
VL = IL * ZeqHV = 1000 VA / 115 V = 8.7 A * (11.616 + j18.032) ohms = 212.62 - j331.53 V
The voltage drop at full load can be calculated using the equivalent impedance as follows:
8.7 A * (11.616 + j18.032) ohms = 212.62 - j331.53 V, where VL = IL * ZeqHV = 1000 VA / 115 V
Next, we may determine the voltage at full load:
VFL = 115 + 212,62 + 327,62 = 327,62
The current is 1.25 times greater at 0.8 lagging power factor than it is at unity power factor. As a result, IL is equal to 1.25 * 1000 VA / (327.62 V * 0.8)
The equivalent circuit of the transformer can be obtained by using the open-circuit and short-circuit test data.
What is transformer?A transformer is an inductive electrical device used to change the alternating current voltage.
The open-circuit test gives the magnetizing branch parameters, while the short-circuit test gives the equivalent resistance and reactance of the transformer.
Magnetizing branch parameters:
Rc = VOC / IOC = 115 V / 0.11 A = 1045 Ω
Xm = VOC / POC = 115 V / 3.9 W = 29.49 Ω
Equivalent resistance and reactance referred to LV side:
RLV = VSC / ISC = (115 V / 230 V)² × 38.1 W / 8.7 A = 0.961 Ω
XLV = (230 V / 115 V)² × 38.1 W / 8.7 A = 4.844 Ω
Voltage regulation is defined as the change in secondary voltage from no-load to full-load expressed as a percentage of the full-load voltage.
At rated condition, the transformer output power is 1000 VA. The input power can be calculated as follows:
Input power = Output power / Efficiency
Assuming the transformer has an efficiency of η, the input power is:
Input power = 1000 VA / η
The voltage drop in the equivalent series impedance (ESZ) of the transformer is:
Vdrop = η × (RLV × I² + XLV × I²) = η × I² × (RLV + XLV)
The secondary voltage at full-load is:
V2 = 115 V
The full-load current is:
I2 = 1000 VA / 115 V = 8.7 A
(i) 0.8 lagging power factor:
The apparent power is:
S = 1000 VA
The real power is:
P = S × 0.8 = 800 W
The reactive power is:
Q = S × sin(arccos(0.8)) = 600 VAR
The input current is:
I1 = S / (η × V1 × 0.8) = 4.35 A
The power factor angle is:
θ = arccos(0.8) = 36.87°
The impedance angle is:
φ = arctan(XLV / RLV) = 79.34°
The voltage drop in the ESZ is:
Vdrop = η × I² × (RLV + XLV) = η × (I1 / cosθ)² × (RLV + XLV)
The secondary voltage under load is:
V2' = V2 - Vdrop = 115 V - η × (I1 / cosθ)² × (RLV + XLV)
The voltage regulation is:
VR = (V2 - V2') / V2 × 100% = η × (I1 / cosθ)² × (RLV + XLV) / V2 × 100%
Substituting the values:
VR = η × (4.35 A / cos(36.87°))² × (0.961 Ω + j4.844 Ω) / 115 V × 100%
= η × 0.0334 × (0.961 + j4.844) / 115 × 100%
= η × 2.13%
(ii) 1.0 power factor:
The real power is:
P = S × 1.0 = 1000 W
The input current is:
I1 = S / (η × V1 × 1.0) = 4.35 A
The power factor angle is:
θ = arccos(1.0) = 0°
The impedance angle is:
φ = arctan(XLV / RLV) = 79.34°
The voltage drop in the ESZ is:
Vdrop = η × I² × (RLV + XLV) = η × (I1 / cosθ)² × (RLV + XLV)
The secondary voltage under load is:
V2' = V2 - Vdrop = 115 V - η × (I1 / cosθ)² × (RLV + XLV)
The voltage regulation is:
VR = (V2 - V2') / V2 × 100% = η × (I1 / cosθ)² × (RLV + XLV) / V2 × 100%
Substituting the values:
VR = η × (4.35 A / cos(0°))² × (0.961 Ω + j4.844 Ω) / 115 V × 100%
= η × 0.0334 × (0.961 + j4.844) / 115 × 100%
= η × 2.13%
(iii) 0.8 leading power factor:
The apparent power is:
S = 1000 VA
The real power is:
P = S × 0.8 = 800 W
The reactive power is:
Q = S × sin(arccos(0.8)) = 600 VAR
The input current is:
I1 = S / (η × V1 × 0.8) = 4.35 A
The power factor angle is:
θ = -arccos(0.8) = -36.87°
The impedance angle is:
φ = arctan(XLV / RLV) = 79.34°
The voltage drop in the ESZ is:
Vdrop = η × I² × (RLV + XLV) = η × (I1 / cosθ)² × (RLV + XLV)
The secondary voltage under load is:
V2' = V2 - Vdrop = 115 V - η × (I1 / cosθ)² × (RLV + XLV)
The voltage regulation is:
VR = (V2 - V2') / V2 × 100% = η × (I1 / cosθ)² × (RLV + XLV) / V2 × 100%
Substituting the values:
VR = η × (4.35 A / cos(-36.87°))² × (0.961 Ω + j4.844 Ω) / 115 V × 100%
= η × 0.0334 × (0.961 + j4.844) / 115 × 100%
= η × 4.74%
Thus, this can be the answer for the given scenario.
For more details regarding transformer, visit:
https://brainly.com/question/11709244
#SPJ1
Ms. Harris sponsors a lunchtime club called Engineering Lab. At the club meetings, students are invited to experiment with their designs. In their first
meeting, one team built and tested a prototype of a toy car while a second team used their time to do more sketching. When both cars were finished
and tested a month later, what was the MOST likely outcome for each team?
O A.
OB.
O C.
O D.
Both teams had spectacular fails.
Both teams had spectacular wins.
The prototype team's car had fewer glitches.
The non-protype team's car had fewer glitches.
Reset
Next
The team who built and tested a prototype of a toy car would have a fewer glitches than the other team.
What is a Prototype?
In order for the participating designers to make the necessary adjustments or changes in direction, a prototype is a straightforward experimental model of a proposed solution that is meant to rapidly and economically test or validate concepts, design assumptions, and other aspects of its development.
What is testing?
Software testing is the procedure of examining and confirming that a software application or product performs as it is designed.
It lessens and gets rid of bugs and faults.
So according to the question the second team are most one to get errors because they spent a lot of time on sketching which is less important than testing.
To know more about Prototype visit:
https://brainly.com/question/28187820
#SPJ9
need help with these two questions. ASAP
Answer:
Explanation:
be confident
Need major help..
Please dont random guess it or answer just for points
Which line of code will have the following output?
[answer: 2.0]
a - [print"answer:", 16 / 8]
b - [print(answer:, 16 / 8)]
c - [print("answer:", 16 / 8)]
Answer:
b in the answer
hope it helps u mark me BRAINLIST
In a very short period of time, the ride-arranging service Uber has grown from a small San Francisco-based startup to a global transportation powerhouse that is redefining the transportation industry. It is not surprising, then, that several governments are receiving tremendous pressure from other transportation companies to prohibit Uber from operating in their nation or community. In an essay of approximately 225 words, describe Uber’s business model and why it is considered a threat to the livelihood of transportation companies and employees in many countries. Include in your review, suggestions as to how these long-established transportation providers might address the Uber threat.
The answer of the given question based on the Uber application startup
growing rapidly the answer is given below,
What is Uber’s business model?Uber's business model is based on a sharing economy concept, which uses a smartphone application to connect riders with drivers.
Uber is a ride-arranging service that uses a smartphone application to connect riders with drivers. The company's business model is based on a sharing economy concept, which allows people to share resources and services with each other through online platforms. The Uber business model is considered a threat to traditional transportation companies and employees because it provides an alternative to traditional taxi and transportation services, which are often more expensive and less efficient.
One of the main reasons why traditional transportation providers see Uber as a threat is that it allows anyone with a car to become a driver, which creates more competition for the traditional taxi industry. Uber's model also provides riders with a convenient and flexible transportation option, which is often more affordable than traditional taxi services.
To address the Uber threat, traditional transportation providers could consider implementing similar sharing economy concepts in their own business models. For example, they could develop their own smartphone applications that connect riders with drivers, or offer car-sharing services to customers. They could also consider lowering their prices and improving their services to compete with Uber.
Another approach for traditional transportation providers would be to work with Uber and other ride-sharing companies to find a mutually beneficial solution. For example, they could partner with Uber to offer combined services that provide customers with a wider range of transportation options. They could also work together to develop regulations and policies that ensure fair competition and protect the interests of all stakeholders involved.
Overall, traditional transportation providers will need to adapt to the changing transportation landscape and find new ways to remain competitive in the face of growing competition from ride-sharing companies like Uber.
To know more about Threat visit:
https://brainly.com/question/30369923
#SPJ1
How often should a technician conduct a Quality Inspection?
Answer: after installation and before first use, and after reassembly at any new site / location. And at suitable intervals to make sure no problems have surfaced.
Why is glass a good insulator?
I don't know the answer but i think it is: "The atoms in glass hold on tightly to their positively charged particles."
The combination of low thermal conductivity, high electrical resistance, amorphous structure, and transparency make glass a good insulator for a wide range of applications.
What are the several reasons that makes glass a good insulator?
Low thermal conductivity: Glass has a low thermal conductivity, which means that it does not conduct heat well. This property makes it difficult for heat to pass through glass, making it a good insulator.High electrical resistance: Glass is also a good electrical insulator due to its high electrical resistance. This means that it does not conduct electricity easily, making it safe for electrical applications.Amorphous structure: Glass has an amorphous structure, meaning that its atoms are arranged in a random pattern rather than a crystalline lattice. This makes it difficult for heat to be transferred through the material by conduction.Transparency: Glass is transparent to most wavelengths of light, which means that it can allow light to pass through while blocking the transfer of heat. This property makes it useful in applications such as windows and greenhouse panels, where it can provide insulation while still allowing sunlight to enter.To learn more about thermal conductivity, visit:
https://brainly.com/question/7643131
#SPJ1
If 4000 is invested now, 7000 four years from now, and 5000 six years from now at an interest rate of 6% compounded annually, what will be the total amount in 9
Explanation:
To solve this problem, we can use the formula for compound interest:
A = P(1 + r/n)^(nt)
where:
A = the final amount
P = the principal amount (the initial investment)
r = the annual interest rate (as a decimal)
n = the number of times the interest is compounded per year
t = the time (in years)
Let's start with the first investment of $4000:
A1 = 4000(1 + 0.06/1)^(1*9)
= 4000(1.06)^9
= $6,542.51
Now, let's move on to the second investment of $7000, made four years from now:
A2 = 7000(1 + 0.06/1)^(1*5)
= 7000(1.06)^5
= $9,381.81
Finally, let's calculate the third investment of $5000, made six years from now:
A3 = 5000(1 + 0.06/1)^(1*3)
= 5000(1.06)^3
= $5,674.32
The total amount after 9 years will be the sum of these three amounts:
Total = A1 + A2 + A3
= $6,542.51 + $9,381.81 + $5,674.32
= $21,598.64
Therefore, the total amount after 9 years will be $21,598.64.
Consider the three-bus system of following Fig. The pu line reactances are indicated on the
figure; the line resistances are negligible. The magnitude of all the three-bus voltages is specified
to be 1.0 pu. The bus powers are specified in the following table.
To solve for the bus voltages and line currents, we will employ the power flow equations.
The power flow equations are given by:
P_1 = V_1I_1*
P_2 = V_2I_2*
P_3 = V_3I_3*
Q_1 = V_1I_1*sinθ_1
Q_2 = V_2I_2*sinθ_2
Q_3 = V_3I_3*sinθ_3
What is Power flow ?Power flow has been the transmission of the electricity from one point to another just through the power grid. It has the flow of the electrical energy from the source of the supply, which is just through an electrical network, that to the point of the consumption.
Power flow has a fundamental concept in the electricity transmission, as it is the actual flow of the electricity which has been affected by the generators, transformers, as well as the capacitors, loads, and other components in the system.
Therefore, The aim has to determine the bus voltages along with the line currents in the three-bus system.
Learn more about voltages on:
https://brainly.com/question/13521443
#SPJ9
Technician A says that frequently overlooked items when conducting a Pre-Delivery Service
include the battery not fully charged, rubber body plugs not installed, and vehicle interior and/or
exterior not thoroughly clean.
Technician B says that frequently overlooked items when conducting a Pre-Delivery Service
include remote keyless system not working properly, poor audio reception, child Safety Door
Looks left in the "ON" position, and seats or seat memory not operating properly.
Who is right?
Pre-Delivery Service (PDS) is a crucial stage in keeping the new car clients of your dealership happy. According to client input, the following areas require extra consideration while completing PDS.
What is Pre delivery service?Thorough inspection for body dents and dings as well as paint chips and scratches. Interior cleanliness; Correct operation of mechanical systems; Appropriate operation of electrical accessories.
Dealers are required to start posting a first oil change reminder sticker prior to delivery to assist in reminding clients that routine oil changes are necessary for the proper maintenance of their vehicle.
Customers will be reminded to visit your dealership again for their initial oil change if you do this.
Therefore, Pre-Delivery Service (PDS) is a crucial stage in keeping the new car clients of your dealership happy. According to client input, the following areas require extra consideration while completing PDS.
To learn more about Pre delivery service, refer to the link:
https://brainly.com/question/9653588
#SPJ9
How is ice removed from aircraft that have ice control systems installed
The de-icing boot consists of a rubber membrane which is inflated and deflated periodically to raise the ice slightly, the air moving over the aircraft wing then removes the raised ice.
Deicing boots are a form of ice protection system that are mounted on aircraft surfaces to allow for mechanical deicing while in flight. As these regions are more likely to accumulate ice and any contamination might significantly impair the performance of the aircraft, such boots are typically mounted on the leading edges of wings and control surfaces (such as the horizontal and vertical stabilisers). Any ice that has built up is cracked by this size expansion and is blasted away into the breeze. The boots are then deflated to restore the wing or surface to its ideal shape. Boots need to be well maintained. Air leakage from holes in the boot could make them less effective.
learn more about de-icing boot here:
https://brainly.com/question/15297300
#SPJ4
Where are floating calipers often used.
Answer:There are pistons on both sides of a fixed caliper. When the brakes are applied, the pistons apply the brake pads on both sides
Explanation:There are pistons on both sides of a fixed caliper. When the brakes are applied, the pistons apply the brake pads on both sides
Which statement about criteria and constraints is true
Criteria define project goals, while constraints set boundaries and limitations, and both are important in the design process.
Define the term boundaries.
Boundaries refer to the limits or constraints that define the extent or scope of something, such as a system, process, or project. Boundaries can be physical, conceptual, or organizational and may be defined by external factors like laws, regulations, or standards, or by internal factors like resources, capabilities, or objectives. Boundaries can help to clarify responsibilities, prevent misunderstandings, and ensure that activities or outcomes are consistent with expectations and requirements.
The statement that is true about criteria and constraints is that they are both important factors to consider in the design process of a project.
Criteria are the desired features, functions, and performance requirements that a project must meet to be considered successful. They define the goals and objectives of the project and help to evaluate whether or not the project has achieved its intended purpose.
Constraints are the limitations and restrictions that affect the design and development of a project. They can be related to resources, such as time, budget, materials, and manpower, as well as technical, legal, ethical, and environmental considerations. Constraints set boundaries and parameters for the project and may require trade-offs or compromises to be made.
In the design process, criteria and constraints are used to guide decision-making and problem-solving. Designers must balance the desired criteria with the constraints that exist, to arrive at a solution that meets the project goals while also being feasible and practical to implement.
Therefore, both criteria and constraints are important and interrelated factors to consider in the design process of a project.
To learn more about boundaries click here
https://brainly.com/question/17414539
#SPJ1
What happens if you depress this brake pedal here?
Any leak in the hydraulic system that causes uneven pressure to be practical to one side of the pressure differential piston will cause the warning light to illuminate.
How do the brake pedals on a car work?When a car's brake pedal is depressed, braking system calipers are energized by hydraulic pressure, clamping down on the disc brake to slow or stop the car.
The light is the only choice here is a short to ground in. This failure would cause the light to stay on all the time regardless of hydraulic condition.
Therefore, the master cylinder is activated when the braking system is depressed, and hydraulic fluid is then transmitted through the brake pedal to both the calipers.
Learn more about hydraulic pressure on:
https://brainly.com/question/857286
#SPJ1
A rotor has been refinished on and off-car brake lathe, you should do all the following except
Inspect the rotor for damage, check thickness, clean, install properly, and torque lug nuts.
Defien torque.
Torque is a measure of the twisting force that causes an object to rotate around an axis or pivot point. It is often expressed in units of pound-feet (lb-ft) or Newton-meters (N-m). Torque is important in many mechanical applications, including automotive engineering, as it determines the ability of a vehicle's engine to generate power and move the vehicle forward. In the context of automotive engineering, torque is the force that is applied to the wheels to turn them and move the vehicle.
If a rotor has been refinished on and off-car brake lathe, here are some things you should do:
1. Inspect the rotor for any visible damage or defects, such as cracks, warping, or excessive wear.
2. Check the thickness of the rotor to ensure that it is still within the manufacturer's specifications.
3. Clean the rotor with brake cleaner to remove any debris or contaminants.
4. Install the rotor onto the vehicle's hub, making sure that it is properly aligned and seated.
5. Torque the lug nuts to the manufacturer's specifications.
To learn more about torque click here
https://brainly.com/question/30338159
#SPJ1
Question
Entropy Analysis of the heat engine: consider a 35% efficient heat engine operating between a large, high-temperature reservoir at 1000 K (727 °C) and a large, cold reservoir at 308 K (35°C).
a. If it withdraws 1.2 MJ/s from the high-temperature reservoir, what would be the rate of loss of entropy from that reservoir and what would be the rate of gain by the low-temperature reservoir?
b. Express the work done by the engine in watts.
c. What would be the total entropy gain of the system?
d. Determine Carnot efficiency and recalculate the a, b, and c, accordingly.
Answer:
a. The rate of loss of entropy from the high-temperature reservoir is 1.2 MJ/s x (1 - 0.35) = 0.78 MJ/s, and the rate of gain of entropy by the low-temperature reservoir is 1.2 MJ/s x 0.35 = 0.42 MJ/s.
b. The work done by the engine is 1.2 MJ/s x 0.35 = 0.42 MW.
c. The total entropy gain of the system is 0.42 MJ/s x (1000 K - 308 K) = 124.8 MJ/s.
d. = 83 MJ/s
Explanation:
Problem 1
A single-phase 100-kVA, 14/2.4-kV transformer and connected to a source through a line impedance of 38.2 + j140 Ω as shown in Figure 1. The transformer’s equivalent series impedance referred to the secondary is 0.10 + j0.40 Ω. The load is 90 kW at 0.8 lagging power factor and 2300 V.
a) Find the voltage of the source.
b) Find the voltage regulation of the transformer for this load.
c) Find the efficiency of the transformer ignoring the core losses.
Answer: Your welcome!
Explanation:
a) The voltage of the source can be calculated using the equation V_source = V_load + I_load * Z_line, where V_load is the voltage of the load, I_load is the current of the load, and Z_line is the line impedance.
Using the given values, we can calculate the voltage of the source as V_source = 2300 V + (90 kW / 0.8 PF) * (38.2 + j140 Ω) = 4576.7 V
b) The voltage regulation of the transformer is the difference between the no-load voltage and the full-load voltage, divided by the full-load voltage. The no-load voltage of the transformer can be calculated using the equation V_NL = V_source * (1 + X_L / X_m), where V_source is the voltage of the source, X_L is the leakage reactance of the transformer, and X_m is the magnetizing reactance of the transformer.
Using the given values, we can calculate the no-load voltage as V_NL = 4576.7 V * (1 + 0.40 / 0.10) = 6378.8 V
The full-load voltage of the transformer can be calculated using the equation V_FL = V_NL - I_FL * Z_eq, where V_NL is the no-load voltage, I_FL is the full-load current of the transformer, and Z_eq is the equivalent series impedance referred to the secondary of the transformer.
Using the given values, we can calculate the full-load voltage as V_FL = 6378.8 V - (90 kW / 0.8 PF) * (0.10 + j0.40 Ω) = 5777.7 V
The voltage regulation of the transformer can then be calculated as VR = (V_NL - V_FL) / V_FL = (6378.8 V - 5777.7 V) / 5777.7 V = 10.3 %
c) The efficiency of the transformer can be calculated using the equation η = (P_out / P_in) * 100, where P_out is the output power of the transformer and P_in is the input power of the transformer.
Using the given values, we can calculate the efficiency as η = (90 kW / (90 kW + (90 kW / 0.8 PF) * (0.10 + j0.40 Ω))) * 100 = 98.5 %
QUESTION 1
1.1. Explain why it is expected that two soil samples separated by 50 kilometers will
have different mineral compositions and particle size distributions.
(4)
1.2. Your geotechnical laboratory team has been tasked with identifying two different
types of rocks for a project in Free State. Discuss briefly the three physical
properties you will utilize to visually identify the rock type.
[13 marks]
(9)
Due to variation in environmental and geological factors, two soil samples from 50 kilometers are expected to have different mineral composition.
Why will two soil samples separated by a distance expected to have different mineral composition1. Two soil samples separated by 50 kilometers are expected to have different mineral compositions and particle size distributions due to variations in geological and environmental factors. Soil is formed through the weathering and breakdown of rocks, which can differ in composition and characteristics depending on the type of rock and geological history of the area. Environmental factors such as climate, topography, and vegetation can also affect soil formation and characteristics. Therefore, the soil samples in two different areas can have different mineral compositions and particle size distributions depending on the local geology and environment.
2. The three physical properties that can be utilized to visually identify different types of rocks are color, texture, and grain size. Color can indicate the presence of certain minerals in the rock, which can help identify the type of rock. Texture refers to the size and arrangement of mineral grains in the rock, which can vary depending on the type of rock and how it was formed. Grain size can also help identify the type of rock, as different rock types have characteristic grain sizes that can be observed with the ordinary eye or under a microscope. Other physical properties that can be used to identify rocks include hardness, density, and porosity.
Learn more on soil sample here;
https://brainly.com/question/23744269
#SPJ1
What happens if you put brake pressure on the pictured caliper?
If you put brake pressure on the pictured caliper than Both technician A and technician B are wrong.
What both Technician A and technician b are discussing?Technician A and technician b are discussing about replacement brake calipers. According to technician A "loaded brake calipers" have no hardware and no brake pads and is remanufactured caliper. Whereas according to technician B, "semi-loaded caliper" has new pads and a hardware.
'Loaded caliper' includes a caliper, friction pads and a hardware. While a 'semi-loaded caliper' is a caliper that includes only the hardware and no friction pads. Technician can choose the friction material of their choice.
Therefore, both the technicians A and B are wrong.
Learn more about caliper on:
https://brainly.com/question/13522392
#SPJ1
Nested for loops. C++
Integer inVal is read from input. For each number from 0 to inVal, output the number followed by the number's value of plus sign characters, '+'. End each output with a newline.
Ex: If the input is 5, then the output is:
0
1+
2++
3+++
4++++
5+++++
------------------------------------------------
#include
using namespace std;
int main() {
int inVal;
int i;
int j;
cin >> inVal;
//Code goes here
return 0;
}
Here's the code to accomplish the task using nested for loops in C++:
#include <iostream>
using namespace std;
int main() {
int inVal;
int i;
int j;
cin >> inVal;
for (i = 0; i <= inVal; i++) {
for (j = 0; j < i; j++) {
cout << "+";
}
cout << i << endl;
}
return 0;
}
Define the term nested.
Nested refers to a situation where one construct, such as a loop or conditional statement, is placed inside another construct of the same type. For example, a nested for loop is a loop within another loop, where the inner loop is executed multiple times for each iteration of the outer loop. Similarly, a nested if statement is an if statement within another if statement, where the inner if statement is only executed if the outer if statement evaluates to true. Nesting is a common programming technique used to solve complex problems by breaking them down into smaller, more manageable parts.
This program reads an integer inVal from input and then uses nested for loops to output each number from 0 to inVal, followed by a corresponding number of plus sign characters. The output for each number is ended with a newline character.
The outer for loop iterates from 0 to inVal, while the inner loop iterates from 0 to i - 1. For each iteration of the inner loop, a plus sign character is output, and after the inner loop, the current value of i is output on a new line. The number of plus sign characters output is determined by the current value of i, since the inner loop runs i times.
Therefore, the program outputs a sequence of numbers followed by a corresponding number of plus sign characters, where the number of plus sign characters for each number increases as the number increases.
To learn more about nested click here
https://brainly.com/question/15020055
#SPJ1
Calculate the pressure drop which must be developed to pump mayonnaise along 15 m of a 40 mm diameter pipeline at a rate of 120 L min−1. Asume density of the fluid is 1090 kg/m3.
The pressure drop required to pump mayonnaise along 15 m of a 40 mm diameter pipeline at a flow rate of 120 L/min is approximately 18083.82 Pa.
What is the pressure dropTo calculate the pressure drop required to pump mayonnaise along 15 m of a 40 mm diameter pipeline at a flow rate of 120 L/min, we can use the Darcy-Weisbach equation:
ΔP = (f × (L/D) × (ρ × V^2)/2)
Where:
ΔP = pressure drop (Pa)
a = friction factor
L = length of pipeline (m)
D = diameter of pipeline (m)
ρ = density of fluid (kg/m^3)
V = velocity of fluid (m/s)
We first need to calculate the velocity of the fluid:
V = Q/A
Where:
Q = flow rate (m^3/s)
A = cross-sectional area of the pipeline (m^2)
Q = 120 L/min = 0.002 m^3/s
A = π×(D/2)^2 = π×(0.04/2)^2 = 0.0012566 m^2
V = 0.002/0.0012566 = 1.59 m/s
Next, we need to calculate the Reynolds number (Re) to determine the friction factor (a):
R = (ρ × V × D)/μ
Where:
μ = dynamic viscosity of fluid (Pas)
For mayonnaise, the dynamic viscosity can be assumed to be around 0.1 Pas.
Re = (1090 kg/m^3 × 1.59 m/s × 0.04 m) / 0.1 Pas = 693.24
Using the Moody chart or an online calculator with the Reynolds number and the relative roughness (ε/D), which is assumed to be 0.001 (typical for commercial steel pipes), we can find that the friction factor is approximately 0.025.
Now, we can calculate the pressure drop:
ΔP = (0.025 × (15/0.04) * (1090 × 1.59^2)/2) = 18083.82 Pa
Learn more on pressure drop here;
https://brainly.com/question/14202357
#SPJ1
A differential leveling circuit began on BM Hydrant (orthometric height 5869.31 ft
) and closed on BM Rock (orthometric height 5880.03 ft
). The plus sight and minus sight distances were kept approximately equal. Readings (in feet) given in the order taken are 3.88 (+S) on BM Hydrant, 5.59 (−S) and 10.83 (+S) on TP1, 7.66 (−S) and 11.81 (+S) on BM 1, 8.91 (−S) and 7.57 (+S) on BM 2, 5.14 (−S) and 9.01 (+S) on TP2, and 5.03 (−S) on BM Rock. Prepare, check, and adjust the notes. (Info in pic)
The answer of the given question based on the levelling circuit calculation is given below,
What is Elevation?Elevation refers to the height of a point above a reference level, usually the mean sea level. In surveying, elevation is often measured using instruments such as levels or total stations to determine the height difference between two points, or to establish a level line or surface.
In this case, we have:
Backsight distance = 3.88 + 3.24 + 1.25 + 1.34 + 5.03 = 14.74 ft
Foresight distance = 5.59 + 10.83 + 7.66 + 11.81 + 9.01 = 45.9 ft
Page check = foresight distance - backsight distance = 31.16 ft
So the page check is 31.16 ft.
To compute the misclosure and correction, we need to compute the sum of the backsight and foresight readings and compare it to the difference in elevation between the starting and ending points. We have:
Sum of backsight readings = 3.88 + 3.24 + 1.25 + 1.34 + 5.03 = 14.74 ft
Sum of foresight readings = 5.59 + 10.83 + 7.66 + 11.81 + 9.01 = 45.9 ft
Difference in elevation = 5880.03 - 5869.31 = 10.72 ft
Misclosure = sum of foresight readings - sum of backsight readings - difference in elevation = 45.9 - 14.74 - 10.72 = 20.44 ft
Correction = misclosure / number of intermediate sights = 20.44 / 4 = 5.11 ft
So the misclosure is 20.44 ft and the correction is 5.11 ft.
To know more about Distance visit:
https://brainly.com/question/15256256
#SPJ1
A ___________ is defined as a change in shape of the part between the damaged and undamaged area hat is smooth and continuous . When the part is straightened, it is returned to proper shape and state without any areas of permanent deformation.
A bend is defined as a change in the shape of the part between the damaged and undamaged area that is smooth and continuous.
What is a kink?
A kink can be defined as a sharp bend with a small radius over a short distance.
So when any part is kinked it must be replaced without any doubt. A part is kinked if it just doesn't work on the repair.
What is a bend?
Unlike a kink, a bend can be restored. That is after a bend also a part can be bought back to its original position.
When the part is straightened, it is returned to proper shape and state without any areas of permanent deformation.
To know more about bend visit:
https://brainly.com/question/27937041
#SPJ9
What type of caliper is shown here?
Answer:
its a floating caliper definetly
What is the purpose of "post-quantum" cryptography?
The development of cryptographic systems that are resistant to both quantum and classical computers is the aim of post-quantum cryptography, often known as quantum-resistant cryptography.
To develop encryption techniques that quantum computers cannot decrypt is the goal of post-quantum cryptography?The basic objective of post-quantum cryptography (PQC), commonly referred to as quantum-resistant cryptography, is to create a secure system that works with current network and communication protocols. It is crucial that the system be protected from both quantum and conventional computers.
What principles govern post-quantum cryptography?Post-quantum cryptography refers to cryptographic techniques that are believed to be secure against a quantum computer attack (often public-key algorithms). It can take typical computers months or even years to solve these difficult mathematical equations.
To know more about cryptography visit:-
https://brainly.com/question/15205343
#SPJ1
What is a distinguishing feature of a centralized intelligent lighting control system?
Answer:
Centralized intelligent lighting control systems are set up and operated using server-based software that is accessible from a workstation. The programmer can create zones, discover devices, assign the devices to zones, set up schedules and control profiles, create users/access levels, and calibrate sensors.
Hope this helps. :)
What happens if you put brake pressure on the pictured caliper?
Brake fluid flows out the bleed screw.
The brake pistons move away from the rotor. Both brake pistons move towards the rotor.
One brake piston moves towards the rotor
If you put brake pressure on the pictured calliper, the brake pistons move away from the rotor. Both brake pistons move towards the rotor.
The brake pad, a tiny block of friction material with a metal plate backing, is located inside the calliper. When you press down on your brake pedal, pistons inside the calliper force the brake pad to squeeze the rotor, which slows or stops the car.
What is caliper ?An (American Spelling) caliper (British spelling as calliper, or in plural tantum sense a pair of callipers) is a device used to measure the dimensions of an object.
Many types of calipers permit reading out a measurement on a ruled scale, a dial, or a digital display. Some calipers can be as simple as a compass with inward or outward-facing points, but no scale. The tips of the caliper are adjusted to fit across the points to be measured and the dimension read by measuring between the tips with another measuring tool, such as a ruler.
It is used in many fields such as mechanical engineering, metalworking, forestry, woodworking, science and medicine.
Learn more caliper
https://brainly.com/question/13522392
#SPJ1
two technicians are discussing what could be wrong with a hydraulically controlled automatic transmission/ transaxle that does not shift out of first gear regardless of vehicle speed. Technician A says that a defective governor could be the cause. Technician B says that a weak pump could be the cause.
Technician B says that a weak pump could be the cause. Tech a technician is correct.
What does an automatic transmission contain?The torque converter, hydraulic pump, planetary gears, clutches, and brakes are important components of the automatic transmission. The torque converter delivers engine power to the transmission input shaft and hydraulic pump. The planetary gears are arranged in a series, one after the other.
What is automatic transmission's purpose?An automatic transmission's primary function is to provide a wide range of output speeds while allowing the engine to operate within its limited speed range.
Question incomplete:
Two technicians are discussing what could be wrong with a hydraulically controlled automatic transmission/transaxle that does not shift out of first gear regardless of vehicle speed. Technician A says that a defective governor could be the cause. Technician B says that a weak pump could be the cause. Which technician is correct?
Learn more about automatic transmission:
brainly.com/question/14093047
#SPJ1
One mole of an monatomic ideal gas at 25 and 1 atm undergoes the following reversibly conducted cycle
19.15JK−1mol−1 is the change in entropy due to the expansion of 1 mole of an ideal gas at 25oC is subjected to expand reversibly ten times of its initial volume.
Entropy is a notion in science and a quantifiable physical characteristic that is frequently connected to a condition of disorder, unpredictability, or uncertainty. The phrase and its underlying idea are employed in a wide range of disciplines, from classical thermodynamics—where they were initially identified—through statistical physics, which uses them to describe nature at the molecular level, to the foundations of information theory. It has numerous applications in physics and chemistry, biological systems and how they relate to life, cosmology, economics, sociology, weather science, the study of climate change, and information systems, particularly the transfer of information via telecommunication. Scottish engineer and scientist William Rankine first used the terms thermodynamic function and heat potential to describe the thermodynamic notion in 1850.
learn more about Entropy here:
https://brainly.com/question/20166134
#SPJ4