ANSWER FAST AND I WILL GIVE BRAINLIEST What is the measurement of this square?
A. 0.75
B 1.75
C 0.34

Answer:

0.75

plz award brainliest now

Hand tools and power tools should be cleaned and stored in the same manner. A) True B) False

Lockheed Martin Skunk Works designs and produces aircraft for defense using rapid prototyping tools
False
True

An engineer would like to create a new set of office supplies that are 100% recyclable. They will include staplers, pens, paper organizers, and computers. He would like to have preset molds to make just the frames of these items in mass bulk. Which of the following materials would be a good choice to begin exploring this project?


ceramics

metals

wood

glass

What is the measurement on this Dial Caliper?
A. 5.491
B. 4.044
C. 5.691

Potential eye injuries are one hazard of using GMAW equipment.

A) True B) False

Question 9 of 25
Which statement could be a scientific theory?
A. The properties of atoms determine which element they belong to.
B. The behavior of atoms can be tested using sophisticated
laboratory equipment.
C. Atoms combine and separate in predictable ways.
D. Tiny particles called atoms are the fundamental units of matter.

Which of the following explains why civil engineers take courses that focus on understanding the forces involved in mechanical systems?

to test efficiency of energy usage
to create safe, stable structures
to design chips and circuit boards
to build effective communications systems

should the wood be touching the sanding belt when you turn on the machine?​

how can a magnet be used to produce an electric current? a. hold the magnet next to a wire b. connect a wire to each end of the magnet c. wrap a wire around the magnet d. spin the magnet around inside a coil or wire

Hard woods and tight curves should be cut using what blade speeds.
faster
O faster
O slower
O it doesn't matter​

Chapter 9
Hand Tools
Review Questions


Why are wrenches offset 15 degrees?

What are the other names for a line wrench?

What are the standard automotive drive sizes for sockets?

What type of screwdriver requires the use of a hammer or mallet?

What is inside a dead blow hammer?

What type of cutter is available in left and right cutters?

The tolerance for a geometric can be easily identified by reading the _________.
A. Datum
B. Baseline
C. Dimension
D. Feature control frame

I WILL GIVE BRAINLIEST IF ANSWER FAST What is the measurement on this Dial Caliper?
A. 5.491 inches
B. 4.044
C. 5.691

HELP I NEED THIS DONE IN 20 MINUTES I WILL GIVE THAT PERSON 50 POINTS IF THEY DO

Is it better to do blue prints with paper and pencil or a computer program if you’re going to design a house? Why?

ASME gives several recommendations for lettering. Which one among the following list is not part of those considerations?

a
The minimum lettering size is .125mm on engineering drawings.
b
All dimension numerals, notes, and other lettered information should be the same height.
c
The spacing of letters in words should be such that the individual letters are uniformly spaced.
d
Notes should be lettered horizontally on the sheet.

I JUST PLAYED A GAME IN 2ND PERSON AND IM CONFEUSED

I NEED THIS DONE ASAP!!!!!! List 4 materials that would light up this light bulb when dropped onto the crocodile clips. In 1-2 sentences, describe why it caused the light to turn on using these 4 key terms: conductor, circuit, electrons, flow.

Complete the following sentence.
have properties that must be considered when designing a product.

PLZ HURRY IM ON A TIMER
Fran has a job involved with controlling the flow of oil through a series of pipelines at the refinery. As a part of his work, he needs to interpret diagrams, levels, and readings from gauges. He also needs to be ready with the appropriate procedures in case of an emergency.

Which career pathway does Fran most likely work in based on these tasks?

Energy Generation
Energy Transmission
Energy Distribution
Energy Transformation

Select the correct answer.
Which equation gives you the amount of work performed?

The amount of risk involve in driving is determined by

Which statement is most undeniably true?


Products can be redesigned for improvements.

As long as you have worked as an apprentice, it is not necessary to go to college to become an engineer.

Engineering is a slow-growing industry.

Engineers are not very employable in today’s job market.

Can someone do this for me Take picture of steps and result and send me link I did the other models but I’m struggling with this one I’ll do anything you want me to do I’ll do anything Plz I’m lost

Which risk is most closely associated with workers in construction engineering?
A.
risk of silicosis because of inhaling very minute silica particles
B.
risk of skin burns because of corrosive acids and alkalis
C.
risk of exposure to a fatal amount of electric current because of malfunctioning equipment
D.
risk of accidental exposure to radiation when handling radioactive elements

A happy, excited driver



is less impaired than an angry driver.


is never affected by passengers in the vehicle.


is a safe driver.


can be just as impaired as an angry driver.

the type of nail used in fine cabinet work is the (blank) nail

What is the main difference between gases and liquids in fluid power?

As much as engineers try to avoid it, end-user problems are part of the process. You might have noticed that right after the latest smartphone comes out, there is a slew of articles pointing out what is not working properly with the phone. This is just one example of an end-user problem. Go online and find an example of an end-user problem. Describe the problem and how the company that created the problem plans to fix it. Include a link to the site where you found the information in your response.

• How many players from each team played before it was changed to 5 players?