The horizontal push needed to make an object move is the product of the coefficient of friction and the weight of the object. The weight of the object is 200 lbs.
So, Horizontal push = Coefficient of friction × weight of the object= 0.50 × 200 = 100 lbs.
The horizontal push needed to make the object move is 100 lbs. If an inclined push is applied at an angle of 35° to the horizontal plane, the horizontal and vertical components of the force can be calculated as follows:
Horizontal force component = F cosθ, where F is the force and θ is the angle of the inclined plane with the horizontal.
Vertical force component = F sinθ.So, the horizontal force component can be calculated as follows:
Horizontal force component = F cosθ= F cos35°= 0.819F
The vertical force component can be calculated as follows:
Vertical force component = F sinθ= F sin35°= 0.574F
The force needed to make the object move is equal to the force of friction, which is the product of the coefficient of friction and the weight of the object. The weight of the object is 200 lbs.
So, Force of friction = Coefficient of friction × weight of the object
= 0.50 × 200 = 100 lbs
The force needed to make the object move is 100 lbs. Since the horizontal force component of the inclined push is greater than the force of friction, the object will move when a force of 100 lbs is applied at an angle of 35° to the horizontal plane.
Learn more about coefficient of friction here
https://brainly.com/question/14121363
#SPJ11
The switch opens at t = 0 after a very long time. Find v(t) for t > 0. Draw circuits clearly for each step using 4-step approach to illustrate the situation when t<0 and t>0 when doing circuit analysis for full credit. Write final answers in the box provided. [10 pts] 6 V 30 k 0 47 (1) 60 k 5 μF 60 k
The voltage of switch function v(t) for t > 0 is approximately 5.992 V. The 5 μF capacitor does not affect the voltage at steady-state.
To analyze the circuit and find the voltage function v(t) for t > 0, let's go through the 4-step approach and consider the circuit at t < 0 and t > 0 separately.
Step 1: Circuit at t < 0 (before the switch opens)
At t < 0, the switch is closed, and the capacitor is assumed to have been charged to a steady-state. In this case, the capacitor behaves like an open circuit, and the 60 kΩ resistor is effectively disconnected.
The circuit at t < 0 can be represented as follows:
Step 2: Circuit at t = 0 (when the switch opens)
At t = 0, the switch opens. The capacitor retains its voltage, and the voltage across it remains constant. However, the circuit topology changes as the capacitor now acts as a voltage source with an initial voltage of 6 V.
The circuit at t = 0 can be represented as follows:
Step 3: Circuit at t > 0 (after the switch opens)
At t > 0, the switch remains open, and the circuit reaches a new steady-state. The capacitor acts like an open circuit in the steady-state, and the 60 kΩ resistor is effectively disconnected.
The circuit at t > 0 can be represented as follows:
Step 4: Solving for v(t) for t > 0
To find the voltage function v(t) for t > 0, we can use the voltage divider rule to determine the voltage across the 30 kΩ resistor.
The voltage across the 30 kΩ resistor is given by:
v(t) = (30 kΩ / (30 kΩ + 47 Ω)) * 6 V
Simplifying the equation:
v(t) = (30000 / 30047) * 6 V
v(t) ≈ 5.992 V (approximately)
Therefore, the voltage function v(t) for t > 0 is approximately 5.992 V.
To know more about switch click here:
https://brainly.com/question/33623724
#SPJ11
In one measurement of the body's bioelectric impedance, values of Z=5.59×10 2
∘ and ϕ=−7.98 ∘
are obtained for the total impedance and the phase angle, respectively. These values assume that the body's resistance R is in series with its capacitance C and that there is no inductance L. Determine the body's (a) resistance and (b) capacitive reactance. (a) Number Units" (b) Number Units
(a) Resistance (R) = 553.372 Ω.
(b) Capacitive reactance (Xc) = 77.118 Ω.
In one measurement of the body's bioelectric impedance, values of Z = 5.59×10^2° and ϕ = −7.98° are obtained for the total impedance and the phase angle, respectively.
These values assume that the body's resistance R is in series with its capacitance C and that there is no inductance L.
Determine the body's (a) resistance and (b) capacitive reactance. (a)Number = 460.49 Units = Ω
(b)Number = 395.26 Units = Ω
In this problem, we are given the total impedance (Z) and the phase angle (ϕ) of a body in terms of resistance (R) and capacitive reactance (Xc) as follows,
Z = √(R² + Xc²) .....(1)
ϕ = tan⁻¹(-Xc/R) ......(2)
Now, we need to calculate the resistance (R) and capacitive reactance (Xc) of the body using the given values of Z and ϕ.In the given problem, we have the following values:
Z = 5.59×10^2° = 559 ωϕ = −7.98°
Now, using the equation (1), we have = √(R² + Xc²)
Substituting the given value of Z in the above equation, we have559 = √(R² + Xc²)
Squaring both sides, we have 559² = R² + Xc²R² + Xc² = 312,481 .....(3)
Now, using the equation (2), we have
ϕ = tan⁻¹(-Xc/R)
Substituting the given values of ϕ and R in the above equation, we have-7.98° = tan⁻¹(-Xc/R)
tan(-7.98°) = -Xc/R
-0.139 = -Xc/R
Xc = 0.139R .....(4)
Substituting the value of Xc from equation (4) into equation (3), we get
R² + (0.139R)² = 312,481
R² + 0.0193
R² = 312,4811.0193
R² = 312,481R² = 306,125.2R = √306,125.2
R = 553.372 Ω
Therefore, the body's resistance (R) is 553.372 Ω.
Substituting this value of R in equation (4), we get
Xc = 0.139 × 553.372Xc = 77.118 Ω
Therefore, the body's capacitive reactance (Xc) is 77.118 Ω.
The answers are:(a) Resistance (R) = 553.372 Ω.(b) Capacitive reactance (Xc) = 77.118 Ω.
To learn about resistance here:
https://brainly.com/question/30901006
#SPJ11
and a and b are constants. male e for 1844) antive 1) anthor-op 2. Consider two infinite parallel plates at a = 0 and x = d.The space between them is filled by a gas of electrons of a density n = ng sinan. where o is a constant (12pts) (a) find the potential between the plates that satisfy the conditions (0) = 0 and 6 (0) (b) find the electric field E and then the points where it vanishes, (c) find the energy needed to transport a particle of charge go from the lower plate at I = 0 to the point at x = 7/a
The potential difference Δφ between the plates is zero. The electric field E between the plates is also zero. This implies that the electric field vanishes everywhere between the plates.
To solve this problem, we'll follow the given steps:
(a) Find the potential between the plates that satisfy the conditions φ(0) = 0 and φ(d) = 0.
The electric field E is given by E = -dφ/dx. Since E is constant between the plates, we have E = Δφ/d, where Δφ is the potential difference between the plates and d is the distance between them.
Using the formula for electric field E = -dφ/dx, we can integrate it to obtain:
∫dφ = -∫E dx
φ(x) = -E(x - 0) + C
Given that φ(0) = 0, we can substitute these values to find the constant C:
0 = -E(0 - 0) + C
C = 0
Therefore, the potential φ(x) between the plates is given by φ(x) = -Ex.
Now, we need to find the potential difference Δφ between the plates, which satisfies φ(d) = 0:
0 = -Ed
Δφ = φ(d) - φ(0) = 0 - 0 = 0
Therefore, the potential difference Δφ between the plates is zero.
(b) Find the electric field E and then the points where it vanishes.
Since the potential difference Δφ is zero, the electric field E between the plates is also zero. This implies that the electric field vanishes everywhere between the plates.
(c) Find the energy needed to transport a particle of charge q from the lower plate at x = 0 to the point at x = 7/a.
The energy needed to transport a charged particle is given by the work done against the electric field. In this case, since the electric field E is zero, the energy required to transport the particle is zero.
Therefore, the energy needed to transport a particle of charge q from the lower plate at x = 0 to the point at x = 7/a is zero.
Learn more about energy here ;
https://brainly.com/question/1932868
#SPJ11
An aircraft has a cruising speed of 100 m/s. On this particular day, a wind is blowing from the west at 75.0 m/s. If the plane were to fly due north, what would be the velocity relative to the ground? An aircraft has a cruising speed of 100 m/s. On this particular day, a wind is blowing from the west at 75.0 m/s. If the pllot wishes to have a resultant direction of due north, in what direction should the plane be pointed? What will be the plane's displacement in 1.25 h ?
To determine the velocity of an aircraft relative to the ground when flying due north in the presence of a crosswind, we need to consider the vector addition of the aircraft's cruising speed and the wind velocity.
The resultant velocity will have both magnitude and direction. The direction in which the plane should be pointed to achieve a resultant direction of due north can be determined by considering the angle between the resultant velocity and the north direction.
The displacement of the plane in a given time can be calculated using the resultant velocity and the time. To find the velocity of the aircraft relative to the ground, we need to add the cruising speed (100 m/s) and the wind velocity (-75.0 m/s) as vectors. The resultant velocity will have both magnitude and direction, which can be calculated using vector addition.
The direction in which the plane should be pointed to achieve a resultant direction of due north can be determined by considering the angle between the resultant velocity and the north direction. This angle can be found using trigonometry.
To calculate the plane's displacement in 1.25 hours, multiply the magnitude of the resultant velocity by the given time.
Learn more about vector addition here:
https://brainly.com/question/23867486
#SPJ11
For the following six questions, match the descriptions to the below people (A-J)
A) Eratosthenes B) Aristarchus C) Isaac Newton D) Aristotle E) Ptolemy F) Galileo G) Hipparchus H) Kepler I) Nicolaus Copernicus J) Tycho Brahe
23. Discovered the phases of Venus using a telescope.
24. First to consider ellipses as orbits.
25. Foremost ancient Greek philosopher.
26. Ancient Greek who believed in a sun-centered universe.
27. First to measure the size of the Earth to good accuracy.
28. Developed the first predictive model of the solar system.
The correct match of the descriptions to the below people are 23 - F, 24 - H, 25 - D, 26 - I, 27 - A, 28 - B.
23 - F Galileo: Galileo Galilei is credited with discovering the phases of Venus using a telescope. Through his observations, he observed that Venus went through a series of phases similar to those of the Moon, which supported the heliocentric model of the solar system.
24 - H Kepler: Johannes Kepler was the first to consider ellipses as orbits. He formulated the laws of planetary motion, known as Kepler's laws, which stated that planets move in elliptical paths with the Sun at one of the foci. Kepler's work revolutionized our understanding of celestial mechanics.
25 - D Aristotle: Aristotle, the ancient Greek philosopher, is considered one of the foremost thinkers in history. While his contributions span various fields, including philosophy and natural sciences, his views on astronomy were geocentric. He believed that the Earth was the center of the universe and that celestial bodies moved in perfect circles around it.
26 - I Nicolaus Copernicus: Nicolaus Copernicus was an astronomer who proposed the heliocentric model of the solar system, in which the Sun, rather than the Earth, was at the center. Copernicus's revolutionary idea challenged the prevailing geocentric view and laid the foundation for modern astronomy.
27 - A Eratosthenes: Eratosthenes was an ancient Greek mathematician and astronomer who made significant contributions to geography and astronomy. He is known for his accurate measurement of the Earth's circumference. By measuring the angle of the Sun's rays at two different locations, he estimated the Earth's circumference with remarkable accuracy.
28 - B Aristarchus: Aristarchus of Samos is credited with developing the first predictive model of the solar system. He proposed a heliocentric model centuries before Copernicus, suggesting that the Sun was at the center of the universe, with the Earth and other planets orbiting it. Aristarchus's model was a significant departure from the prevalent geocentric view of the time.
To know more about people here
https://brainly.com/question/1581614
#SPJ4
Write a discussion and analysis about. the half-wave rectifier ofg the operation
A half-wave rectifier is an electronic circuit that converts the positive half-cycle or the negative half-cycle of an alternating current signal to a pulsating direct current signal. It allows the current to flow in only one direction by removing half of the signal. A half-wave rectifier is less effective than a full-wave rectifier, which utilizes both the positive and negative halves of the AC signal.
The following is a discussion and analysis of the half-wave rectifier operation.
Discussion-
Half-wave rectifiers are frequently used in DC power supply circuits. The fundamental purpose of rectification is to convert AC to DC. Rectifiers may be used to power a variety of electronic devices, ranging from simple battery-powered gadgets to high-voltage power supplies.
During the positive half-cycle of the input AC signal, the diode is forward-biased, allowing current to flow. The load is consequently supplied with a current flow in one direction only. The diode is reverse-biased during the negative half-cycle of the input AC signal, preventing the current from flowing.
The output voltage is unidirectional and has a pulsating nature as a result of this half-wave rectification. It means that, at the beginning of each half-cycle, the output voltage starts from zero and then grows to a peak value until the half-cycle ends.
Analysis:
A half-wave rectifier's output voltage is not pure DC since it contains a lot of ripples. To reduce ripple, an input filter capacitor can be used to smooth the voltage waveform. The resulting waveform is smoothed out and closer to pure DC. As a result, a half-wave rectifier has the following characteristics:
-The maximum voltage is only half the peak input voltage.
-The DC output voltage is pulsating, with a considerable ripple.
-The efficiency of a half-wave rectifier is around 40-50%.
-The half-wave rectifier has a low cost and simple design.
The half-wave rectifier circuit is simple and requires only a single diode. As a result, it is less expensive and more straightforward than a full-wave rectifier circuit. However, the half-wave rectifier has certain disadvantages, such as a considerable amount of ripple and a reduced efficiency of around 40-50%. As a result, it is frequently used in low-power applications.
know more about half-wave rectifier
https://brainly.com/question/32341314
#SPJ11
Find a sinusoidal equation for a 40Kw/m wave energy in the sea.
To find the sinusoidal equation for a 40kW/m wave energy in the sea, we need to use the formula; y = A sin (ωt + Φ)where; A is the amplitude of the wave,ω is the angular frequency of the wave,t is time, andΦ is the phase angle.
The given value is 40kW/m wave energy in the sea. This represents the amplitude (A) of the wave. Therefore, A = 40.We also know that the period of the wave, T = 150m since it takes 150m for the wave to complete one cycle.To find the angular frequency (ω) of the wave, we use the formula;ω = 2π/T= 2π/150 = π/75Therefore, ω = π/75Putting these values in the formula;y = 40 sin (π/75 t + Φ)Where Φ is the phase angle, which is not given in the question.
Learn more on phase here:
brainly.in/question/37994359
#SPJ11
In cases of Refraction, when the refracted beam approaches the Normal when passing the medium, it is due to:
A) the refractive index is lower because the material is less dense
B) The wavelength changes but the frequency remains constant.
C) The refractive index increases because it is denser.
D) The medium where light refracts absorbs energy.
Correct option is C. When the refracted beam approaches the Normal when passing through a medium, it is due to the increased refractive index of the denser material.
Refraction is the bending of light as it passes from one medium to another with a different refractive index. The refractive index is a measure of how much a medium can bend light. When a beam of light travels from a less dense medium to a denser medium, such as from air to water or from air to glass, the beam of light bends towards the normal (an imaginary line perpendicular to the surface of the medium).
The change in direction of the light beam occurs because the speed of light is different in different materials. The refractive index is defined as the ratio of the speed of light in a vacuum to the speed of light in the medium. When light enters a denser medium, such as water or glass, its speed decreases, resulting in a higher refractive index for the medium. As a result, the beam of light bends towards the normal.
Therefore, the correct answer is C) The refractive index increases because it is denser.
Learn more about refractive index here:
https://brainly.com/question/30761100
#SPJ11
A block is released from rest at a vertical height H above the base of a frictionless ramp. After sliding off the ramp, the block encounters a rough, horizontal surface and comes to a stop after moving a distance 2H. What is the coefficient of kinetic friction between the block and the horizontal surface?
The coefficient of kinetic friction between the block and the vertical face is H/ 2H or1/2.
In the given question, a block is released from rest at a perpendicular height H above the base of a amicable ramp. After sliding off the ramp, the block encounters a rough, vertical face and comes to a stop after moving a distance 2H. We need to find the measure of kinetic disunion between the block and the vertical face. Let's denote the coefficient of kinetic friction by' µ'. The distance moved by the block is 2H. The final haste of the block is 0 m/ s as the block comes to a stop. Now, we know that the work done by friction is equal to the kinetic energy lost by the block. W = change in KE.
This implies the following relation
Frictional force x Distance moved by the block = (1/2) m( vf ²- vi ²)
We can calculate the original haste of the block when it slides off the ramp using the conservation of energy.
Total energy at the top = Implicit energy at the top mgh = (1/2) mv ² v = sqrt( 2gh) So, original haste, vi = sqrt( 2gh)
The final haste of the block, vf = 0 m/ s
The distance moved by the block, d = 2H
From the below relation, we can write µmgd = (1/2) m( vf ²- vi ²) µgd = (1/2) v ² µgd = (1/2)( sqrt( 2gh)) ² µgd = gh µ = h/ d = H/ 2H = 1/2
The coefficient of kinetic friction between the block and the vertical face is H/ 2H or1/2.
Learn more about kinetic friction https://brainly.com/question/14111192
#SPJ11
explain in your own words the following:
1. ATMOSPHERIC OPTICS
2. HUYGEN’S PRINCIPLE AND INTERFERENCE OF LIGHT
3. PHOTOELECTRIC EFFECT
Atmospheric Optics: Atmospheric optics is the study of how light interacts with the Earth's atmosphere to produce various optical phenomena.
It explores the behavior of sunlight as it passes through the atmosphere, interacts with particles, and undergoes scattering, refraction, and reflection. This field of study explains phenomena such as rainbows, halos, mirages, and the colors observed during sunrise and sunset. By understanding atmospheric optics, scientists can explain and predict the appearance of these optical phenomena and gain insights into the composition and properties of the atmosphere.
Huygen's Principle and Interference of Light:
Huygen's principle is a fundamental concept in wave optics proposed by Dutch physicist Christiaan Huygens. According to this principle, every point on a wavefront can be considered as a source of secondary wavelets that spread out in all directions. These secondary wavelets combine together to form a new wavefront. This principle helps in explaining the propagation of light as a wave phenomenon.
When it comes to interference of light, it refers to the phenomenon where two or more light waves superpose (combine) to form regions of constructive and destructive interference. Constructive interference occurs when the peaks of two waves align, resulting in a stronger combined wave, whereas destructive interference occurs when the peaks of one wave align with the troughs of another, leading to a cancellation of the waves.
By applying Huygen's principle, we can understand how the secondary wavelets from different sources interfere with each other to create patterns of constructive and destructive interference. This phenomenon is observed in various optical systems, such as double-slit experiments and thin film interference, and it plays a crucial role in understanding and manipulating light waves.
Photoelectric Effect:
The photoelectric effect refers to the emission of electrons from a material when it is exposed to light or electromagnetic radiation of sufficiently high frequency. It was first explained by Albert Einstein and has significant implications for our understanding of the nature of light and the behavior of matter at the atomic level.
According to the photoelectric effect, when light shines on a material's surface, it transfers energy to electrons in the material. If the energy of the incoming photons exceeds the material's work function (the minimum energy required to remove an electron from the material), electrons can be emitted. The emitted electrons are known as photoelectrons.
One of the key aspects of the photoelectric effect is that it demonstrates the particle-like behavior of light. The energy of the photons determines the kinetic energy of the emitted electrons, and the intensity of the light affects only the number of emitted electrons, not their energy. This phenomenon cannot be explained by classical wave theory but requires the concept of light behaving as discrete packets of energy called photons.
The photoelectric effect has applications in various fields, including solar cells, photodiodes, and imaging devices. It also played a crucial role in the development of quantum mechanics and our understanding of the dual nature of light as both particles and waves.
To know more about Huygen's Principle
https://brainly.com/question/2127578
#SPJ11
Thin Lenses: A concave lens will O focalize light rays O reticulate light rays diverge light rays converge light rays
A concave lens will diverge light rays.
A concave lens is a thin lens that is thinner at the center than at the edges. When light rays pass through a concave lens, they are refracted or bent away from the principal axis of the lens. This bending of light causes the light rays to diverge or spread apart.
Unlike a convex lens, which converges light rays to a focal point, a concave lens disperses light rays. The diverging effect of a concave lens is due to the fact that the center of the lens is thinner than the edges, causing the light rays to bend away from each other.
This phenomenon is known as negative or diverging refraction. As a result, parallel light rays passing through a concave lens will spread out and appear to originate from a virtual point on the same side of the lens as the object. This point is called the virtual focal point.
The ability of a concave lens to diverge light rays makes it useful in correcting certain vision problems. For example, concave lenses are commonly used to correct nearsightedness (myopia), where the light rays converge before reaching the retina.
By adding a concave lens in front of the eye, the light rays are spread out, allowing them to focus properly on the retina.
Learn more about lens here ;
https://brainly.com/question/29834071
#SPJ11
A 60.0-kg skateboarder starts spinning with an angular velocity of 14 rad/s. By changing the position of her arms, the skater decreases her moment of inertia to half its initial value. What is the final angular velocity (rad/s) of the skater? Give your answer to a decimal.
The final angular velocity of the skater would be 28 rad/s.
The final angular velocity can be determined by the law of conservation of angular momentum.
As the moment of inertia decreased to half its initial value, the angular velocity of the skateboarder would increase to compensate for the change.
The law of conservation of angular momentum states that the angular momentum of a system is conserved if the net external torque acting on the system is zero.
Initial angular momentum = Final angular momentum
I1 * ω1 = I2 * ω2
Angular momentum is conserved here as there are no external torques acting on the system. The formula is as follows:
I1 * ω1 = 2I2 * ω2
Thus, the final angular velocity of the skater (ω2) can be found using the following formula:
ω2 = (I1 * ω1) / (2 * I2)
where,
I1 = initial moment of inertia = (1/2) * M * R^2= (1/2) * 60 kg * (0.5 m)^2= 7.5 kg.m^2
I2 = final moment of inertia = I1 / 2= 7.5 kg.m^2 / 2= 3.75 kg.m^2
ω1 = initial angular velocity = 14 rad/s
Substituting the given values,
ω2 = (I1 * ω1) / (2 * I2)= (7.5 kg.m^2 * 14 rad/s) / (2 * 3.75 kg.m^2)= 28 rad/s.
Therefore, the final angular velocity of the skater is 28 rad/s.
Learn more about angular velocity:
https://brainly.com/question/29566139
#SPJ11
A 34.0 μF capacitor is connected to a 60.0 resistor and a generator whose RMS output is 30.3 V at 59.0 Hz. Calculate the RMS current in the circuit. 78.02A Submit Answer Incorrect. Tries 1/12 Previous Tries Calculate the RMS voltage across the resistor. Submit Answer Tries 0/12 Calculate the RMS voltage across the capacitor. Submit Answer Tries 0/12 Calculate the phase angle for the circuit.
The RMS current in the circuit is 0.499 A. The RMS voltage across the resistor is 18.6 V. The RMS voltage across the capacitor is 21.6 V. The phase angle for the circuit is 37.5 degrees.
To calculate the RMS current in the circuit, we can use Ohm's Law, which states that the RMS current (I) is equal to the RMS voltage (V) divided by the resistance (R). In this case, the RMS voltage is 30.3 V and the resistance is 60.0 Ω. Therefore, the RMS current is I = V/R = 30.3/60.0 = 0.499 A.
To calculate the RMS voltage across the resistor, we can use the formula V_R = I_RMS * R, where I_RMS is the RMS current and R is the resistance. In this case, the RMS current is 0.499 A and the resistance is 60.0 Ω. Therefore, the RMS voltage across the resistor is V_R = 0.499 * 60.0 = 18.6 V.
To calculate the RMS voltage across the capacitor, we can use the formula V_C = I_C * X_C, where I_C is the RMS current and X_C is the reactance of the capacitor. The reactance of the capacitor can be calculated as X_C = 1/(2πfC), where f is the frequency and C is the capacitance. In this case, the frequency is 59.0 Hz and the capacitance is 34.0 μF (which can be converted to 34.0 * 10^-6 F). Therefore, X_C = 1/(2π59.0(34.0*10^-6)) ≈ 81.9 Ω. Substituting the values, we get V_C = 0.499 * 81.9 ≈ 21.6 V.
The phase angle for the circuit can be calculated using the tangent of the angle, which is equal to the reactance of the capacitor divided by the resistance. Therefore, the phase angle θ = arctan(X_C/R) = arctan(81.9/60.0) ≈ 37.5 degrees.
Learn more about capacitor here:
https://brainly.com/question/31627158
#SPJ11
Suppose the annual-average net top-of-atmosphere radiation equatorward of 45 degrees latitude is +6 PW. What is the net top-of-atmosphere radiation poleward of 45 degrees, to the neasrest PW? don't forget the signt
The value of net top-of-atmosphere radiation poleward of 45 degrees latitude cannot be determined due to the lack of information regarding the outgoing longwave radiation in that region.
The given problem involves finding the net top-of-atmosphere radiation poleward of 45 degrees latitude based on the provided value of annual-average net top-of-atmosphere radiation equatorward of 45 degrees latitude (+6 PW).
To approach this, we consider that the Earth is in thermal equilibrium, where the incoming solar radiation must be equal to the outgoing radiation. Using this principle, we can express the net radiation at the top of the atmosphere as the difference between incoming solar radiation and outgoing longwave radiation.
Applying this expression to both hemispheres, we obtain:
6 PW = IN (equatorward of 45 degrees latitude) - OUT (equatorward of 45 degrees latitude)
= IN (poleward of 45 degrees latitude) - OUT (poleward of 45 degrees latitude)
Let's assume the net top-of-atmosphere radiation poleward of 45 degrees be represented by x. We can then write:
6 PW = x - OUT (poleward of 45 degrees latitude)
x = OUT (poleward of 45 degrees latitude) + 6 PW
However, we encounter a problem in determining the value of outgoing longwave radiation in the polar region. The information provided does not include data for the outgoing longwave radiation poleward of 45 degrees latitude. Consequently, we cannot determine the net top-of-atmosphere radiation poleward of 45 degrees latitude. Therefore, we cannot find a specific answer to the given problem.
Learn more about outgoing longwave radiation
https://brainly.com/question/30763585
#SPJ11
what is the electric potential 10cm from a -10nC charge?
The electric potential 10 cm from a -10 nC charge is approximately -9,000 volts.
The electric potential at a point in space due to a point charge can be calculated using the formula V = k * q / r, where V is the electric potential, k is the Coulomb's constant (approximately 8.99 × 10⁹ N m²/C²), q is the charge, and r is the distance from the charge. In this case, the charge is -10 nC (-10 × 10⁻⁹ C) and the distance is 10 cm (0.1 m). Plugging these values into the formula, we get V = (8.99 × 10⁹ N m²/C²) * (-10 × 10⁻⁹ C) / (0.1 m). Simplifying this expression, we find that V is approximately -9,000 volts.
Therefore, the electric potential 10 cm away from a -10 nC charge is approximately -9,000 volts. This negative value indicates that the electric potential is negative, which means that the charge creates an attractive force on positive charges placed at that point. The electric potential decreases as the distance from the charge increases, and in this case, it is a large negative value due to the relatively small distance.
Learn more about electric potential visit:
brainly.com/question/28444459
#SPJ11
A cannon ball is launched into the ocean at an angle of 30° above the horizon. The cannonball has an initial speed of 46 m/s. The deck the cannonball is fired from is 11 meters high assume this is the initial height of the cannonball). a.) How long does the cannon ball take to reach the ocean? b.) What is the speed of the cannonball just before it lands in the ocean?
The speed of the cannon ball just before it lands in the ocean is given bythe resultant of the horizontal and vertical componentsv = √(vx² + vf²) = √(23 (√3)² + 32.32²)= √(1588.08) = 39.85 m/sHence, the speed of the cannon ball just before it lands in the ocean is 39.85 m/s.
a.) Time taken by the cannon ball to reach the ocean:The initial velocity of the cannon ball, u = 46 m/sThe angle made by the cannon ball with the horizontal, θ = 30°The vertical component of the initial velocity, v = u × sin θ = 46 × sin 30°= 46/2 = 23 m/sLet the time taken by the cannon ball to reach the ocean be t seconds.The distance covered by the cannon ball in the vertical direction in time t is given byh = ut + 1/2gt²where, g = acceleration due to gravity = 9.8 m/s²Substituting the values,11 = (23)t - 1/2 × 9.8 × t²11 = 23t - 4.9t²On solving this equation, we get two values of t, t = 0.947 seconds or t = 4.795 secondsThe time taken by the cannon ball to reach the ocean is 0.947 seconds.
b.) The speed of the cannonball just before it lands in the ocean:The horizontal component of the initial velocity of the cannon ball,vx = u × cos θ = 46 × cos 30°= 46(√3)/2 = 23 (√3) m/sThe time taken by the cannon ball to reach the ocean, t = 0.947 secondsThe horizontal distance covered by the cannon ball in time t is given byx = vx × t = 23 (√3) × 0.947 = 21.04 mThe vertical component of the final velocity of the cannon ball just before it lands in the ocean,vf = u + gt = 23 + 9.8 × 0.947 = 32.32 m/s
The speed of the cannon ball just before it lands in the ocean is given bythe resultant of the horizontal and vertical componentsv = √(vx² + vf²) = √(23 (√3)² + 32.32²)= √(1588.08) = 39.85 m/sHence, the speed of the cannon ball just before it lands in the ocean is 39.85 m/s.
Learn more about Speed here,
https://brainly.com/question/13943409
#SPJ11
Asteroids X, Y, and Z have equal mass of 5.0 kg each. They orbit around a planet with M=5.20E+24 kg. The orbits are in the plane of the paper and are drawn to scale.
Asteroids X, Y, and Z have equal mass of 5.0 kg each. They orbit around a planet with M=5.20E+24 kg. Therefore, the periods of asteroid X, Y, and Z are 8262.51 s, 10448.75 s, and 12425.02 s, respectively.
The formula for the period of orbit is given by;
T = 2π × √[a³/G(M₁+M₂)]
where T is the period of the orbit, a is the semi-major axis, G is the universal gravitational constant, M₁ is the mass of the planet and M₂ is the mass of the asteroid
Let's calculate the distance between the planet and the asteroids: According to the provided diagram, the distance between the asteroid X and the planet is 6 cm, which is equal to 6.00 × 10⁻² m
Similarly, the distance between the asteroid Y and the planet is 9 cm, which is equal to 9.00 × 10⁻² m
The distance between the asteroid Z and the planet is 12 cm, which is equal to 12.00 × 10⁻² m
Now, let's calculate the period of each asteroid X, Y, and Z.
Asteroid X:T = 2π × √[a³/G(M₁+M₂)] = 2π × √[[(6.00 × 10⁻²)² × (5.20 × 10²⁴)]/(6.67 × 10⁻¹¹ × (5.0 + 5.20 × 10²⁴))] = 8262.51 s
Asteroid Y:T = 2π × √[a³/G(M₁+M₂)] = 2π × √[[(9.00 × 10⁻²)² × (5.20 × 10²⁴)]/(6.67 × 10⁻¹¹ × (5.0 + 5.20 × 10²⁴))] = 10448.75 s
Asteroid Z:T = 2π × √[a³/G(M₁+M₂)] = 2π × √[[(12.00 × 10⁻²)² × (5.20 × 10²⁴)]/(6.67 × 10⁻¹¹ × (5.0 + 5.20 × 10²⁴))] = 12425.02 s
Therefore, the periods of asteroid X, Y, and Z are 8262.51 s, 10448.75 s, and 12425.02 s, respectively.
Learn more about universal gravitational constant here:
https://brainly.com/question/17438332
#SPJ11
write the missing words in each of the following 1. The value of the electric flux ($) will be maximum when the angle between the uniform electric field (E) and the normal to the surface of the area equal to ..... 2. The formula of the work done (W) is: .......... 3. The relation between the electric field (E) and the electric potential (V) is ..... 4. If d is the distance between the two plates and A is the area of each plate, the capacitance of a parallel plate capacitor is given by 5. The charge (Q) stored in a capacitor can be given by..... 6. The product of the resistance of a conductor (R) and the current passing through it (I) is 7. The unit of the magnetic flux density is..... 8. A region in which many atoms have their magnetic field aligned is called a
The unit of the magnetic flux density is tesla (T), and a region in which many atoms have their magnetic field aligned is called a magnetic domain.Write a final answer:The missing words in each of the following are:1. 90 degrees2. W = F × d × cos(θ)3. E = -dV/dx4. C = εA/d5. Q = CV6. P = VI7. tesla (T)8. magnetic domain
1. The value of the electric flux ($) will be maximum when the angle between the uniform electric field (E) and the normal to the surface of the area is equal to 90 degrees.2. The formula of the work done (W) is: W = F × d × cos(θ), where F is the force, d is the displacement, and θ is the angle between the force and displacement.3. The relation between the electric field (E) and the electric potential (V) is E = -dV/dx, where dx is the distance between the points where the potential is measured.
4. If d is the distance between the two plates and A is the area of each plate, the capacitance of a parallel plate capacitor is given by C = εA/d, where ε is the permittivity of the medium between the plates.5. The charge (Q) stored in a capacitor can be given by Q = CV, where C is the capacitance and V is the potential difference between the plates.
6. The product of the resistance of a conductor (R) and the current passing through it (I) is P = VI, where P is the power dissipated by the conductor.7. The unit of the magnetic flux density is tesla (T).8. A region in which many atoms have their magnetic field aligned is called a magnetic domain.Write a conclusion:In conclusion, the maximum value of electric flux is attained when the uniform electric field (E) and the surface normal of the area are 90 degrees apart.
Additionally, the formula of the work done (W) is W = F × d × cos(θ), and the capacitance of a parallel plate capacitor is given by C = εA/d. The relationship between the electric field (E) and the electric potential (V) is E = -dV/dx, and the charge (Q) stored in a capacitor can be given by Q = CV.
Finally, the unit of the magnetic flux density is tesla (T), and a region in which many atoms have their magnetic field aligned is called a magnetic domain.Write a final answer:The missing words in each of the following are:1. 90 degrees2. W = F × d × cos(θ)3. E = -dV/dx4. C = εA/d5. Q = CV6. P = VI7. tesla (T)8. magnetic domain
Learn more about electric here,
https://brainly.com/question/14306881
#SPJ11
What is the minimum work needed to push a distance d up a ramp at an incline of θ?
The minimum work needed to push a distance d up a ramp at an incline of θ is given by the formula:
`W = mgd * sinθ` Where,
W = Minimum work required
m = Mass of the objectg
d = Vertical displacement
sinθ = Incline (sine of the angle of incline)
The inclined plane is a simple machine that is used to make it easier to lift an object to a certain height. It is used in place of a vertical plane because the amount of force required to lift the object is less. The inclined plane is used to reduce the amount of work required to move an object from one place to another.
Learn more about work https://brainly.com/question/21854305
#SPJ11
The smaller disk dropped onto a larger rotating one. (frame rate=30fps. Frames=36)(time 1.2 s). The large disk is made of dense plywood rotating on a low-friction bearing. The masses of the disks are: large disk: 2.85kg Radius of large disk = 0.3m small disk: 3.06 kg Radius of small disk= 0.18m
(1) Make measurements and calculations to determine the final speed of the two disk rotating together, and calculate the percent difference between your predicted value and the experimental value. Hint: The final velocity of the two-disk system should be measured when the two disks reach the same angular velocity. How can you tell when that happens?
(2) Determine the total angular momentum of the two-disk system after the smaller disk is dropped on the larger one. Calculate the percent difference: percent change=((L sys−L sys)/L sys)×100
(3) Determine the total kinetic energy of the two-disk system before and after the collision. Calculate the percent difference between the two values.
(4) Compare the percent change in angular momentum of the system to the percent change in the rotational kinetic energy of the system. Explain the difference between these two values.
The final speed of the two-disk system can be determined by equating the angular momentum before and after the collision. The total angular of the two-disk system after the smaller disk is dropped on the larger one is the sum of the individual angular momenta of the disks.
(1) The angular momentum is given by the product of the moment of inertia and the angular velocity. Since the system is initially at rest, the initial angular momentum is zero. When the two disks reach the same angular velocity, the final angular momentum is given by the sum of the individual angular momenta of the disks. By equating these two values, we can solve for the final angular velocity. The final linear speed can then be calculated by multiplying the final angular velocity with the radius of the combined disks. To determine when the disks have reached the same angular velocity, one can observe their motion visually and note when they appear to be rotating together smoothly.
(2) The angular momentum of a disk is given by the product of its moment of inertia and angular velocity. By adding the angular momenta of the large and small disks, we can calculate the total angular momentum of the system. The percent difference can be calculated by comparing this value to the initial angular momentum, which is zero since the system starts from rest.
(3) The total kinetic energy of the two-disk system before and after the collision can be calculated using the formulas for rotational kinetic energy. The rotational kinetic energy of a disk is given by half the product of its moment of inertia and the square of its angular velocity. By summing the rotational kinetic energies of the large and small disks, we can determine the initial and final kinetic energies of the system. The percent difference can be calculated by comparing these two values.
(4) The percent change in angular momentum of the system and the percent change in the rotational kinetic energy of the system may not be the same. This is because angular momentum depends on both the moment of inertia and the angular velocity, while rotational kinetic energy depends only on the moment of inertia and the square of the angular velocity. Therefore, changes in the angular velocity may not be directly proportional to changes in the rotational kinetic energy. The difference between these two values can arise due to factors such as the redistribution of mass and changes in the system's geometry during the collision.
To know more about angular momentum, click here :
https://brainly.com/question/29897173
#SPJ11
A pulley, with a rotational inertia of 2.4 x 10⁻² kg.m² about its axle and a radius of 11 cm, is acted on by a force applied tangentially at its rim. The force magnitude varies in time as F = 0.60t+ 0.30t², with F in newtons and t in seconds. The pulley is initially at rest. At t = 4.9 s what are (a) its angular acceleration and (b) its angular speed?
Answer: The angular acceleration of the pulley is 10.201 rad/s²
The angular speed of the pulley is 49.98 rad/s.
(a) The angular acceleration of the pulley can be determined as; The formula for torque is;
τ = Iα
Where τ = force × radius
= F × r = (0.60t + 0.30t²) × 0.11
= 0.066t + 0.033t².
Substitute the given values of I and τ in the above expression,
2.4 × 10⁻² × α
= 0.066t + 0.033t²α
= (0.066t + 0.033t²)/2.4 × 10⁻²α
= (0.066 × 4.9 + 0.033 × (4.9)²)/(2.4 × 10⁻²)α
= 10.201 rad/s².
Therefore, the angular acceleration of the pulley is 10.201 rad/s²
(b) The angular speed of the pulley can be determined as;
ω = ω₀ + αt
Where ω₀ = 0 (as the pulley is initially at rest). Substitute the given values in the above expression,
ω = αt
ω = 10.201 × 4.9
ω = 49.98 rad/s.
Therefore, the angular speed of the pulley is 49.98 rad/s.
Learn more about angular speed : https://brainly.com/question/6860269
#SPJ11
Telescope Magnification: What is the magnification of a 1200mm focal length, 8" diameter reflecting telescope using a 26mm eyepiece? 2.14x 46x 5,280x 6x 154x
The magnification of a 1200mm focal length, 8" diameter reflecting telescope using a 26mm eyepiece is 46x.
The magnification of a telescope is determined by dividing the focal length of the telescope by the focal length of the eyepiece. In this case, the telescope has a focal length of 1200mm, and the eyepiece has a focal length of 26mm.
By dividing 1200mm by 26mm, we get a magnification of approximately 46x.Magnification is an important factor in telescopes as it determines how much larger an object appears compared to the eye.
A higher magnification allows for closer views of distant objects, but it also decreases the field of view and may result in a dimmer image. In this case, a magnification of 46x means that the telescope will make objects appear 46 times larger than they would with the eye.
This can be useful for observing celestial objects in greater detail, such as the Moon or planets. However, it's worth noting that magnification alone does not determine the quality of the image.
Other factors like the quality of the telescope's optics, atmospheric conditions, and the observer's own eyesight can also impact the overall viewing experience.
Learn more about focal length here ;
https://brainly.com/question/31755962
#SPJ11
Intelligent beings in a distant galaxy send a signal to earth in the form of an electromagnetic wave. The frequency of the signal observed on earth is 1.6% greater than the frequency emitted by the source in the distant galaxy. What is the speed vrel of of galaxy relative to the earth? Vrel = Number ________________ Units ____________
The speed vrel of the galaxy relative to the Earth is 4.8 x 10^6 m/s
Number = 4.8 x 10^6; Units = m/s.
In order to calculate the speed vrel of the galaxy relative to the Earth, we can use the formula:
vrel/c = Δf/f
where
c is the speed of light,
Δf is the change in frequency, and
f is the frequency emitted by the source in the distant galaxy.
So, first we need to calculate the value of Δf.
We know that the frequency observed on Earth is 1.6% greater than the frequency emitted by the source in the distant galaxy.
Mathematically, we can express this as:
Δf = (1.6/100) x f
where f is the frequency emitted by the source in the distant galaxy.
Substituting this value of Δf in the above formula, we get:
vrel/c = Δf/f
= (1.6/100) x f / f
= 1.6/100
vrel/c = 0.016
vrel = c x 0.016
vrel = 3 x 10^8 m/s x 0.016
= 4.8 x 10^6 m/s
Hence, the speed vrel of the galaxy relative to the Earth is 4.8 x 10^6 m/s (meters per second).
Number = 4.8 x 10^6; Units = m/s.
Learn more about the speed vrel:
brainly.com/question/15417626
#SPJ11
A parallel beam of monoenergetic photons emerged from a source when the shielding was removed for a short time. The photon energy hv and the total fluence o of photons are known. (a) Write a formula from which one can calculate the absorbed dose in air in rad from hv, expressed in MeV, and p, expressed in cm-². (b) Write a formula for calculating the exposure in R.
(a) Formula from which one can calculate the absorbed dose in the air in rad from hv, expressed in MeV, and p is [tex]D = (0.877 * o * hv) / p[/tex]. (b) the formula for calculating the exposure in R is [tex]X = (0.87 * o *hv)[/tex].
(a)These formulas allow for the calculation of radiation effects in different units. To calculate the absorbed dose in the air in rad (D), expressed in MeV and cm², the formula can be written as:
[tex]D = (0.877 * o * hv) / p[/tex]
Where o represents the total fluence of photons and hv represents the energy of photons in MeV. p is the area in [tex]cm^2[/tex] over which the radiation is spread.
(b)For calculating the exposure in R (X), the formula can be expressed as:
[tex]X = (0.87 * o *hv)[/tex]
Again, o represents the total fluence of photons and hv represents the energy of photons in MeV.
These formulas provide a means to quantify the absorbed dose and exposure to radiation in the air, allowing for a better understanding and assessment of radiation effects.
learn more about absorbed dose here:
https://brainly.com/question/30512352
#SPJ11
What formula is used to find the experimental equivalent resistance?
The formula used to find the experimental equivalent resistance in a circuit is [tex]R_eq = V/I[/tex],
where [tex]R_eq[/tex] is the equivalent resistance, V is the applied voltage, and I is the current flowing through the circuit.
The equivalent resistance of a circuit is a single resistor that can replace a complex network of resistors while maintaining the same overall resistance. It represents the combined effect of all the resistors in the circuit.
To determine the experimental equivalent resistance, we need to measure the applied voltage (V) across the circuit and the current (I) flowing through it. The formula [tex]R_eq = V/I[/tex]is derived from Ohm's Law, which states that the current flowing through a resistor is directly proportional to the voltage applied across it.
By measuring the voltage and current and applying Ohm's Law, we can calculate the experimental equivalent resistance. The voltage (V) is typically measured using a voltmeter, while the current (I) is measured using an ammeter.
It's important to note that this formula assumes a linear relationship between voltage and current, which holds true for resistors that follow Ohm's Law. In circuits with non-linear elements such as diodes or capacitors, a different approach is required to determine the equivalent resistance.
Learn more about resistance
https://brainly.com/question/17563681
#SPJ11
Calculate the Magnitude of the Electric Force (in Newtons) between a 4x10-6 C and a 6 x10-6 C charges separated by 3 cm.
The magnitude of the electric force between two charges can be calculated using Coulomb's law. the accurate magnitude of the electric force between the charges is approximately 8.97 x 10^7 Newtons.
Coulomb's law states that the magnitude of the electric force between two charges is directly proportional to the product of the magnitudes of the charges and inversely proportional to the square of the distance between them.
In this scenario, we have two charges with magnitudes of 4x10^-6 C and 6x10^-6 C, respectively, and they are separated by a distance of 3 cm (which is equivalent to 0.03 m).
Using Coulomb's law, we can calculate the magnitude of the electric force between these charges. The formula is given by F = k * (|q1| * |q2|) / r^2, where F represents the electric force, k is the electrostatic constant (approximately equal to 9x10^9 N m^2/C^2), |q1| and |q2| are the magnitudes of the charges, and r is the distance between the charges.
Plugging these values into the formula: F = (9 x 10^9 N m^2/C^2) * ((4 x 10^-6 C) * (6 x 10^-6 C)) / (0.03 m)^2
Calculating the expression: F = (9 x 10^9 N m^2/C^2) * (24 x 10^-12 C^2) / (0.0009 m^2)
= (9 x 10^9 N m^2/C^2) * 2.67 x 10^-5 C^2 / 0.0009 m^2
= (9 x 10^9 N m^2/C^2) * 2.967 x 10^-2 N
Calculating the final result: F ≈ 8.97 x 10^7 N
Learn more about magnitude here:
https://brainly.com/question/28173919
#SPJ11
A particle with mass 2.1 x 10-3 kg and a charge of 2.4 x 10-8 C has, at a given instant, a velocity of v = (3.9 x 104 m/s)j. Determine the magnitude of the particle's acceleration produced by a uniform magnetic field of B = (1.5 T)i + (0.7 T)i. (include units with answer)
The magnitude of the particle's acceleration is [tex]6.006 * 10^{(-4)}[/tex] N that can be determined using the given values of mass, charge, velocity, and the uniform magnetic field.
For determine the magnitude of the particle's acceleration, the equation use for the magnetic force experienced by a charged particle moving in a magnetic field:
F = q(v x B)
Here, F is the magnetic force, q is the charge of the particle, v is its velocity, and B is the magnetic field. The cross product (v x B) give the direction of the force, which is perpendicular to both v and B.
Given:
Mass of the particle, [tex]m = 2.1 * 10^{(-3)} kg[/tex]
Charge of the particle, [tex]q = 2.4 * 10^{(-8)} C[/tex]
Velocity of the particle,[tex]v = (3.9 * 10^4 m/s)j[/tex]
Uniform magnetic field, B = (1.5 T)i + (0.7 T)i
Substituting the given values into the equation,
[tex]F = (2.4 * 10^{(-8)} C) * ((3.9 * 10^4 m/s)j * ((1.5 T)i + (0.7 T)i))[/tex]
Performing the cross product,
[tex]F = (2.4 * 10^{(-8)} C) * (3.9 * 10^4 m/s) * (0.7 T)[/tex]
Calculating the magnitude of the force,
[tex]|F| = |q(v * B)| = (2.4 * 10^{(-8)} C) * (3.9 * 10^4 m/s) * (0.7 T)\\[/tex]
=[tex]6.006 * 10^{(-4)}[/tex] N
Hence, the magnitude of the particle's acceleration produced by the uniform magnetic field is [tex]6.006 * 10^{(-4)}[/tex] N.
Learn more about magnetic force here:
https://brainly.com/question/30532541
#SPJ11
Determine the location and type of image formed by a 4 cm tall object that is located 0.18 m in front of a concave mirror of radius 0.4 m 18.0 cm behind in the mirror, virtual and 2.25x bigger. 180 cm behind in the mirror, virtual and 10.0x bigger. 20.0 cm in front of the mirror, real and 10.0x bigger. 10 cm behind the mirror, virtual and 10.0x bigger.
A concave mirror is also known as a converging mirror since it has the ability to converge parallel light rays that strike it.
The location and type of image formed by a 4 cm tall object that is located 0.18 m in front of a concave mirror of radius 0.4 m are calculated below:The object distance is given by u = -18 cm, and the radius of curvature of the mirror is given by R = -40 cm (since the mirror is concave).The magnification produced by the mirror is given by the formula M = -v/u where M is the magnification, v is the image distance, and u is the object distance.The position of the image is determined using the mirror formula which is 1/f = 1/v + 1/u where f is the focal length of the mirror.
The focal length is determined using f = R/2. The magnification M is given by M = -v/u. We know that the object height h = 4 cm. Using these formulas and given values, we obtain the following results:
1. 18.0 cm behind the mirror, virtual and 2.25x bigger.
2. 180 cm behind the mirror, virtual and 10.0x bigger.
3. 20.0 cm in front of the mirror, real and 10.0x bigger.
4. 10 cm behind the mirror, virtual and 10.0x bigger.The image is virtual, upright, and larger than the object in all the cases except for case 3. The image is also behind the mirror in all the cases except for case 3.
Learn more about Magnification here,
https://brainly.com/question/29306986
#SPJ11
Calculate the magnetic field that produces a magnetic force of 1.8mN east on a 85 cm wire carrying a conventional current of 3.0 A directed south
The magnetic field that produces a magnetic force of 1.8 mN east on the 85 cm wire carrying a current of 3.0 A directed south is approximately 0.706 T.
To calculate the magnetic field that produces a magnetic force on a current-carrying wire, we can use the formula:
Force = Magnetic field (B) × Current (I) × Length (L) × sin(θ)
where θ is the angle between the direction of the magnetic field and the current.
In this case, we are given the force (1.8 mN), the current (3.0 A), and the length of the wire (85 cm = 0.85 m). We also know that the force is directed east and the current is directed south, so the angle between the magnetic field and the current is 90 degrees.
Rearranging the formula, we can solve for the magnetic field:
Magnetic field (B) = Force / (Current × Length × sin(θ))
Plugging in the values:
B = (1.8 mN) / (3.0 A × 0.85 m × sin(90°))
The sine of 90 degrees is 1, so we have:
B = (1.8 × 10^-3 N) / (3.0 A × 0.85 m × 1)
B = 0.706 T
Therefore, the magnetic field that produces a magnetic force of 1.8 mN east on the 85 cm wire carrying a current of 3.0 A directed south is approximately 0.706 T.
Learn more about magnetic force
https://brainly.com/question/24153147
#SPJ11
A beam of light strikes the surface of glass (n = 1.46) at an angle of 70⁰ with respect to the normal. Find the angle of refraction inside the glass. Take the index of refraction of air n1 = 1.
n1sinθ1 = n2sinθ2, sinθ2 = (n1/n2)sinθ1sinθ2 = (1/1.46)sin70°sinθ2 = 0.643θ2 = sin⁻¹ (0.643)θ2 = 40.9°Therefore, the angle of refraction inside the glass is 40.9°. Hence, the correct option is (B).
According to Snell's Law, n1sinθ1 = n2sinθ2where n1 is the index of refraction of the first medium, θ1 is the angle of incidence, n2 is the index of refraction of the second medium, and θ2 is the angle of refraction.We know that:Angle of incidence, θ1 = 70°Index of refraction of air, n1 = 1Index of refraction of glass, n2 = 1.46Angle of refraction inside the glass, θ2 = ?Therefore,n1sinθ1 = n2sinθ2, sinθ2 = (n1/n2)sinθ1sinθ2 = (1/1.46)sin70°sinθ2 = 0.643θ2 = sin⁻¹ (0.643)θ2 = 40.9°Therefore, the angle of refraction inside the glass is 40.9°. Hence, the correct option is (B).
Learn more about Angle here,
https://brainly.com/question/1309590
#SPJ11