the maximum magnitude is 5.5
6. How would the measurements for potential difference and current change if a 200 Ω resistor was used in Circuit 1 instead of the 100 Ω resistor? Explain your answer.
Answer:
Explanation:
Resistance is defined as the opposition to the flow of an electric current in a circuit. This means that a higher amount of resistance tends to reduce the amount of current flowing through the resistance. The lower the current, the greater the possibility for the resistor to allow current to pass through it. if a 200 Ω resistor was used in Circuit 1 instead of the 100 Ω resistor, then the current in the circuit will tends to increase since we are replacing the load with a lesser resistor and a smaller resistance tends to allow more current to flow through it
For the potential difference, a decrease in the resistance value will onl decrease the potential difference flowing in the circuit according to ohm's law. According to the law the pd in a circuit is directly proportional to the current which means an increase in the resistance value will cause an increase in the corresponding pd and vice versa.
A ballistic pendulum consists of a 4 kg wooden block originally at rest at θ = 0o . When a 2 g bullet strikes and becomes embedded it, it is observed that the block swings upward to a maximum angle of θ = 6o . Estimate the speed of the bullet just before the impact.
Answer:
733m/s
Explanation:
Assuming that Just after impact:
given that at lowest point Is
T2 + V2 = T3 + V3
1 /2(4 + 0.002) (vB)²2 + 0 = 0 + (4 + 0.002)(9.81)(1.25)(1 -cos 6°)
(vB)2 = 0.3665
m>s For the system of bullet and block: ( S+ ) Σmv1 = Σmv2 0.002(vB)1 = (4 + 0.002)(0.3665) (vB)1 = 733 m/s
A particle initially located at the origin has an acceleration of = 2.00ĵ m/s2 and an initial velocity of i = 6.00î m/s. (a) Find the vector position of the particle at any time t (where t is measured in seconds). ( t î + t2 ĵ) m (b) Find the velocity of the particle at any time t. ( î + t ĵ) m/s (c) Find the coordinates of the particle at t = 4.00 s. x = m y = m (d) Find the speed of the particle at t = 4.00 s. m/s
Answer:
a)
6t i + t² j m
b)
6 i + 2 t j m/s
c)
x = 24 m and y = 16 m
d)
10 m/s
Explanation:
Explanation is given in the attached document.
If the voltage amplitude across an 8.50-nF capacitor is equal to 12.0 V when the current amplitude through it is 3.33 mA, the frequency is closest to:
5.19 x 10³Hz
Explanation:The capacitive reactance, [tex]X_{C}[/tex], which is the opposition given to the flow of current through the capacitor is given by;
[tex]X_C = \frac{1}{2\pi fC }[/tex]
Where;
f = frequency of the signal through the capacitor
C = capacitance of the capacitor.
Also, from Ohm's law, the voltage(V) across the capacitor is given by the product of current(I) and the capacitive reactance. i.e;
V = I x [tex]X_{C}[/tex] [Substitute the value of
=> V = I x [tex]\frac{1}{2\pi fC}[/tex] [Make f the subject of the formula]
=> f = [tex]\frac{I}{2\pi VC}[/tex] ---------------------(i)
From the question;
I = 3.33mA = 0.00333A
C = 8.50nF = 8.50 x 10⁻⁹F
V = 12.0V
Substitute these values into equation (i) as follows;
f = [tex]\frac{0.00333}{2 * 3.142 * 12.0 * 8.50 * 10^{-9}}[/tex] [Taking [tex]\pi[/tex] = 3.142]
f = 5.19 x 10³Hz
Therefore, the frequency is closest to f = 5.19 x 10³Hz
You shine unpolarized light with intensity 54.0 W/m^2 on an ideal polarizer, and then the light that emerges from this polarizer falls on a second ideal polarizer. The light that emerges from the second polarizer has intensity 19.0 W/m^2. Find the angle between the polarizing axes of the two polarizers.°
Answer:
The angle between the polarizing axes of the two polarizers is 54°
Explanation:
Given;
intensity of unpolarized light, I₀ = 54.0 W/m²
intensity of light that emerges from second ideal polarizer, I₁ = 19.0 W/m²
The angle between the polarizing axes of the two polarizers is dtermined by applying Malus' law for intensity of a linearly polarized light passing through a polarizer.
I₁ = I₀Cos²θ
Cos²θ = I₁ / I₀
Cos²θ = 19 / 54
Cos²θ =0.3519
Cos θ = √0.3519
Cos θ = 0.5932
θ = Cos⁻¹(0.5932)
θ = 53.6°
θ = 54°
Therefore, the angle between the polarizing axes of the two polarizers is 54°
The Hermes spacecraft is traveling at 0.1c(1/10 the speed of light past Mars and shines a laser in front of the ship. You would see the light traveling at c (the speed of light )away from your ship. According to Einstein's special relativity how fast with a person on Mars observe the light to be traveling?
Answer:
So, according to Einstein's special relativity a person on Mars observe the light to be traveling at c = 3 x 10⁸ m/s.
Explanation:
The special theory of relativity has two main postulates:
1- VALIDITY OF PHYSICAL LAWS
The laws of physics such as Newton's Laws and Maxwell's Equations are valid in all inertial frame of references.
2- CONSTANCY OF SPEED OF LIGHT
The speed of light in vacuum is the same for all observers in uniform translational relative motion, and it is independent of the motion of the source or the observer. Thus, speed of light is a universal constant and its value is c = 3 x 10⁸ m/s.
So, according to Einstein's special relativity a person on Mars observe the light to be traveling at c = 3 x 10⁸ m/s.
Describe the orientation of magnetic field lines by drawing a bar magnet, labeling the poles, and drawing several lines indicating the direction of the forces.
Answer:
A field is a way of mapping forces surrounding any object that can act on another object at a distance without apparent physical connection. The field represents the object generating it. Gravitational fields map gravitational forces, electric fields map electrical forces, and magnetic fields map magnetic forces.
Explanation:
Determine the two coefficients of static friction at B and at C so that when the magnitude of the applied force is increased to 360 N , the post slips at both B and C simultaneously.
Now, there is some information missing to this problem, since generally you will be given a figure to analyze like the one on the attached picture. The whole problem should look something like this:
"Beam AB has a negligible mass and thickness, and supports the 200kg uniform block. It is pinned at A and rests on the top of a post, having a mass of 20 kg and negligible thickness. Determine the two coefficients of static friction at B and at C so that when the magnitude of the applied force is increased to 360 N , the post slips at both B and C simultaneously."
Answer:
[tex]\mu_{sB}=0.126[/tex]
[tex]\mu_{sC}=0.168[/tex]
Explanation:
In order to solve this problem we will need to draw a free body diagram of each of the components of the system (see attached pictures) and analyze each of them. Let's take the free body diagram of the beam, so when analyzing it we get:
Sum of torques:
[tex]\sum \tau_{A}=0[/tex]
[tex]N(3m)-W(1.5m)=0[/tex]
When solving for N we get:
[tex]N=\frac{W(1.5m)}{3m}[/tex]
[tex]N=\frac{(1962N)(1.5m)}{3m}[/tex]
[tex]N=981N[/tex]
Now we can analyze the column. In this case we need to take into account that there will be no P-ycomponent affecting the beam since it's a slider and we'll assume there is no friction between the slider and the column. So when analyzing the column we get the following:
First, the forces in y.
[tex]\sum F_{y}=0[/tex]
[tex]-F_{By}+N_{c}=0[/tex]
[tex]F_{By}=N_{c}[/tex]
Next, the forces in x.
[tex]\sum F_{x}=0[/tex]
[tex]-f_{sB}-f_{sC}+P_{x}=0[/tex]
We can find the x-component of force P like this:
[tex]P_{x}=360N(\frac{4}{5})=288N[/tex]
and finally the torques about C.
[tex]\sum \tau_{C}=0[/tex]
[tex]f_{sB}(1.75m)-P_{x}(0.75m)=0[/tex]
[tex]f_{sB}=\frac{288N(0.75m)}{1.75m}[/tex]
[tex]f_{sB}=123.43N[/tex]
With the static friction force in point B we can find the coefficient of static friction in B:
[tex]\mu_{sB}=\frac{f_{sB}}{N}[/tex]
[tex]\mu_{sB}=\frac{123.43N}{981N}[/tex]
[tex]\mu_{sB}=0.126[/tex]
And now we can find the friction force in C.
[tex]f_{sC}=P_{x}-f_{xB}[/tex]
[tex]f_{sC}=288N-123.43N=164.57N[/tex]
[tex]f_{sC}=N_{c}\mu_{sC}[/tex]
and now we can use this to find static friction coefficient in point C.
[tex]\mu_{sC}=\frac{f_{sC}}{N}[/tex]
[tex]\mu_{sC}=\frac{164.57N}{981N}[/tex]
[tex]\mu_{sB}=0.168[/tex]
In practice, a good insulator In practice, a good insulator A. slows heat flow. B. speeds negative heat flow. C. stops heat flow. D. all of the above
Answer:
The answer is A. slows heat flow.Explanation:
An insulator is a material that impedes the movement of heat or electric current from flowing.
Theoretically good heat insulators stops the movement of heat, while practically this insulation can only be slowed down.
Hence from the options listed the correct answer practically is
A. slows heat flow.A converging lens has the focal length of 25 cm. A 10-cm object is placed at 30 cm in front of the lens. How far is the image from the lens? What is the size of the image?
Explanation:
Given that,
Focal length of a converging lens, f = +25 cm
Size of the object, h = 10 cm
Object distance, u = -30 cm
We need to find the image distance and the size of the image.
Using lens formula, [tex]\dfrac{1}{v}-\dfrac{1}{u}=\dfrac{1}{f}[/tex], v is image distance
[tex]\dfrac{1}{v}=\dfrac{1}{f}+\dfrac{1}{u}\\\\\dfrac{1}{v}=\dfrac{1}{25}+\dfrac{1}{(-30)}\\\\v=150\ cm[/tex]
Magnification,
[tex]m=\dfrac{v}{u}=\dfrac{h'}{h}[/tex]
h' is the size of image
[tex]h'=\dfrac{vh}{u}\\\\h'=\dfrac{150\times 10}{(-30)}\\\\h'=-50\ cm[/tex]
So, the image distance is 150 cm the size of image is 50 cm.
A particle moves in a velocity field V(x, y) = x2, x + y2 . If it is at position (x, y) = (7, 2) at time t = 3, estimate its location at time t = 3.01.
Answer:
New location at time 3.01 is given by: (7.49, 2.11)
Explanation:
Let's start by understanding what is the particle's velocity (in component form) in that velocity field at time 3:
[tex]V_x=x^2=7^2=49\\V_y=x+y^2=7+2^2=11[/tex]
With such velocities in the x direction and in the y-direction respectively, we can find the displacement in x and y at a time 0.01 units later by using the formula:
[tex]distance=v\,*\, t[/tex]
[tex]distance_x=49\,(0.01)=0.49\\distance_y=11\,(0.01)=0.11[/tex]
Therefore, adding these displacements in component form to the original particle's position, we get:
New position: (7 + 0.49, 2 + 0.11) = (7.49, 2.11)
A blue train of mass 50 kg moves at 4 m/s toward a green train of 30 kg initially at rest. What is the initial momentum of the green train?
Answer:
I think answer is zero
bcz momentum=mass×velocity
body was initially at rest it means its velocity is zero
30×0=0
A generator rotates at 95 Hz in a magnetic field of 0.025 T. It has 550 turns and produces an rms voltage of 170 V and an rms current of 60.0 A.
Required:
a. What is the peak current produced?
b. What is the area of each turn of the coil?
Answer:
Peak current= 84.86 A
Area of each turn = 0.029 m^2
Explanation:
The peak value of current can be obtained from Irms= 0.707Io. Where Io is the peak current.
Hence;
Irms= 60.0A
Io= Irms/0.707
Io = 60.0/0.707
Io= 84.86 A
Vrms= 0.707Vo
Vo= Vrms/0.707= 170/0.707 = 240.45 V
From;
V0 = NABω
Where;
Vo= peak voltage
N= number of turns
B= magnetic field
A= area of each coil
ω= angular velocity
But ω= 2πf = 2×π×95= 596.9 rads-1
Substituting values;
A= Vo/NBω
A= 240.45/550×0.025×596.9
A= 0.029 m^2
Jane is collecting data for a ball rolling down a hill. she measure out a set of different distances and then proceeds to use a stopwatch to find the time it takes the ball to roll each distance
Answer:
The Independent variable in this experiment is the time taken by the ball to roll down each distance.
The dependent variable is the distance through which the ball rolls
The control variables are: slope of hill, weight, of the ball, size of ball, wind speed, surface characteristics of the ball.
Explanation:
The complete question is
Jane is collecting data for a ball rolling down a hill. She measures out a set of different distances and then proceeds to use a stop watch to find the time it takes the ball to roll. What are the independent, dependent, and control variables in this experiment?
Independent variable have their values not dependent on any other variable in the scope of the experiment. The time for the ball to roll down the hill is not dependent on any other variable in the experiment. Naturally, some common independent variables are time, space, density, mass, fluid flow rate.
A dependent variable has its value dependent on the independent variable in the experiment. The value of the distance the ball rolls depends on the time it takes to roll down the hill.
The relationship between the dependent and independent variables in an experiment is given as
y = f(x)
where y is the output or the dependent variable,
and x is the independent variable.
Control variables are those variable that if not held constant could greatly affect the results of an experiment. For an experiment to be more accurate, control variables should be confined to a given set of value throughout the experiment.
An inductor is connected to the terminals of a battery that has an emf of 12.0 V and negligible internal resistance. The current is 4.86 mA at 0.700 ms after the connection is completed. After a long time the current is 6.80 mA.
What are
(a) the resistance R of the inductor and
(b) the inductance L of the inductor?
Answer:
a) 1764.71 ohms
b) 1.73 H
Explanation:
From the question, we can identify the following parameters;
Vo =12 V , i = 4.86 mA, t =0.700 ms, io =6.80 mA
(a) Indcued emf V = L di/dt =0
From ohms law Vo = ioR
R = 12/6.80*0.001
R=1764.71 ohms
(b) For LR circuit
i =io (1-e^-t/T)
Time constant T = L/R
4.86 = 6.80 (1-e^-0.7*10^-3/T)
divide both side by 6.8
0.715 = 0.0007/T
L/R = 0.0007/0.715
L/R = 0.000979020979
Substitute R from above
L = 0.000979020979 * 1764.71
L =1.73 H
A 20 g bullet strikes a 1.5 kg wood block and becomes embedded in it (all horizontal motion). The coefficient of friction between the block and the surface is 0.3 and the impact makes the block move a distance of 7 m before it comes to rest. What was the muzzle speed (in m/s) of the bullet? Report your answer with two significant figures.
Answer:
Explanation:
Kinetic frictional force acting on the block = μ mg
where μ is coefficient of friction , m is mass of block.
.3 x 1.5 x 9.8 = 4.41 N .
Let v be the velocity of bullet + block after collision
kinetic energy of composite mass after the strike
= 1 /2 x 1.52 x v²
this will be equal to work done by friction .
.76 v² = 4.41 x 7
v² = 40.62
v = 6.37 m /s
Now we can obtain muzzle speed of bullet by applying conservation of momentum .
Let this speed be u
initial momentum of bullet
= .02 x u
final momentum of composite mass
= 1.52 x 6.37
.02 u = 1.52 x 6.37
u = 484.12 m /s .
= 480 m /s ( in two significant figures )
A uniform electric field is created by two parallel plates separated by a distance of 0.04 m. What is the magnitude of the electric field established between the plates
Complete question:
A uniform electric field is created by two parallel plates separated by a
distance of 0.04 m. What is the magnitude of the electric field established
between the plates if the potential of the first plate is +40V and the second
one is -40V?
Answer:
The magnitude of the electric field established between the plates is 2,000 V/m
Explanation:
Given;
distance between two parallel plates, d = 0.04 m
potential between first and second plate, = +40V and -40V respectively
The magnitude of the electric field established between the plates is calculated as;
E = ΔV / d
where;
ΔV is change in potential between two parallel plates;
d is the distance between the plates
ΔV = V₁ -V₂
ΔV = 40 - (-40)
ΔV = 40 + 40
ΔV = 80 V
E = ΔV / d
E = 80 / 0.04
E = 2,000 V/m
Therefore, the magnitude of the electric field established between the plates is 2,000 V/m
The magnitude of the electric field developed that lies between the plates should be considered as the 2,000 V/m.
Calculation of the Electric Field:Since
The distance that lies between 2 parallel plates should be d = 0.04 m
The potential that lies between first and second plate should be like +40V and -40V
So, The magnitude of the electric field should be
E = ΔV / d
here,
ΔV represents the change in potential that lies between 2 parallel plates.
d represents the distance between the plates.
So,
ΔV = V₁ -V₂
ΔV = 40 - (-40)
ΔV = 40 + 40
ΔV = 80 V
And,
E = ΔV / d
E = 80 / 0.04
E = 2,000 V/m
Therefore, the magnitude of the electric field established between the plates is 2,000 V/m.
learn more about Electric field here: https://brainly.com/question/13266812?referrer=searchResults
An insulated beaker with negligible mass contains liquid water with a mass of 0.285 kg and a temperature of 75.2 ∘C How much ice at a temperature of -22.8 ∘C must be dropped into the water so that the final temperature of the system will be 32.0 ∘C ? Take the specific heat of liquid water to be 4190 J/kg⋅K , the specific heat of ice to be 2100 J/kg⋅K , and the heat of fusion for water to be 3.34×105 J/kg
Answer:
Explanation:
We shall apply the theory of
heat lost = heat gained .
heat lost by water = mass x specific heat x temperature diff
= .285 x 4190 x ( 75.2 - 32 ) = 51587.28 J
heat gained by ice to attain temperature of zero
= m x 2100 x 22.8 = 47880 m
heat gained by ice in melting = latent heat x mass
= 334000m
heat gained by water at zero to become warm at 32 degree
= m x 4190 x 32 = 134080 m
Total heat gained = 515960 m
So
515960 m = 51587.28
m = .1 kg
= 100 gm
Water flows through a cylindrical pipe of varying cross-section. The velocity is 3.0 m/s at a point where the pipe diameter is 1.0 cm. What is the flow rate R
Answer:
The flow rate is [tex]R =2.357 *10^{-4} \ m^3/s[/tex]
Explanation:
From the question we are told that
The velocity is [tex]v = 3.0 \ m/s[/tex]
The diameter of the pipe is [tex]d = 1.0 \ cm = 0.01 \ m[/tex]
The radius of the pipe is mathematically represented as
[tex]r = \frac{d}{2}[/tex]
substituting values
[tex]r = \frac{0.01}{2}[/tex]
[tex]r = 0.005 \ m[/tex]
The flow rate is mathematically represented as
[tex]R = v * A[/tex]
Where is the cross-sectional area of the pipe which is mathematically evaluated as
[tex]A = \pi r^2[/tex]
substituting values
[tex]A = 3.142 * (0.005)^2[/tex]
[tex]A = 7.855 * 10^{-5} \ m^2[/tex]
So
[tex]R = 3.0 * 7.855 *10^{-5}[/tex]
[tex]R = 2.357*10^{-4} \ m^3 /s[/tex]
Current folw in which dirction
An air bubble has a volume of 1.3 cm3 when it is released by a submarine 160 m below the surface of a freshwater lake. What is the volume of the bubble when it reaches the surface? Assume that the temperature and the number of air molecules in the bubble remain constant during the ascent.
Answer:
V2 = 21.44cm^3
Explanation:
Given that: the initial volume of the bubble = 1.3 cm^3
Depth = h = 160m
Where P2 is the atmospheric pressure = Patm
P1 is the pressure at depth 'h'
Density of water = ρ = 10^3kg/m^3
Patm = 1.013×10^5 Pa.
Patm = 101300Pa
g = 9.81m/s^2
P1 = P2+ρgh
P1 = Patm +ρgh
P1 = 1.013×10^5+10^3×9.81×160.
P1 = 101300+1569600
P1 = 1670900 Pa
For an ideal gas law
PV =nRT
P1V1/P2V2 = 1
V2 = ( P1/P2)V1
V2 = (P1/Patm)V1
V2 = ( 1670900 /101300 Pa) × 1.3
V2 = 1670900/101300
V2 = 16.494×1.3
V2 = 21.44cm^3
The volume of the bubble can be determined using ideal gas law. The volume of the bubble when it reaches surface is 21.44 [tex]\bold {cm^3}[/tex].
The formula of the pressure of the static fluid
P1 = P2+ρgh
Where,
P1 - pressure at depth 'h'
P2 - atmospheric pressure = [tex]\bold {1.013x10^5 }[/tex] = 1670900 Pa
h - Depth = 160m
ρ - Density of water = [tex]\bold {10^3\ kg/m^3}[/tex]
g- gravitational acceleration = [tex]\bold {9.81\ m/s^2}[/tex]
The initial volume of the bubble = [tex]\bold {1.3\ cm^3}[/tex]
[tex]\bold {P1 = 1.013x10^5+10^3\times 9.81\times 160}\\\\\bold {P1 = 101300+1569600}\\\\\bold {P1 = 1670900\ Pa}[/tex]
For an ideal gas,
PV =nRT
[tex]\bold {\dfrac {P_1V_1}{P_2V_2 }= 1}[/tex]
[tex]\bold {V2 = \dfrac { P_1}{P_2V_1}}[/tex]
So,
[tex]\bold {V2 = \dfrac {1670900 }{101300 }\times 1.3}\\\\\bold {V2 =21.44\ cm^3}[/tex]
Therefore, the volume of the bubble when it reaches surface is 21.44 [tex]\bold {cm^3}[/tex].
To know more air bubble volume,
https://brainly.com/question/10509397
15. The
of a sine wave is the time it takes to complete one cycle of the wave.
O A. maximum amplitude
O B. minimum amplitude
O C. average value
O D. wavelength
That TIME is called the "period" of the wave.
(It's not one of the choices.)
If theta is 30 degrees and there is no friction, what would be the block's acceleration down the incline, in meters per second squared?
Answer:
a= 4.9m/s²
Explanation:
Using Fnet= mgsintheta = ma
But a= gsintheta
a= 9.8xsin 30
= 4.9m/s²
Which of the following is true about a planet orbiting a star in the uniform circular motion? B. The speed of the plant is always changing. C. The velocity of the plant is constant. D. The acceleration vector of the plant points towards the center of the circle.
Explanation:
If an object moves in a circular path, this type of motion is called uniform circular motion. The speed of the object is constant in this type of motion.As velocity is a vector quantity, it keeps on changing. It can be given by drawing tangent to the circle.Acceleration acts towards the center of circle. Hence, out of the given four options, the correct statement about a planet orbiting a star in uniform circular motion is (d) i.e. The acceleration vector of the plant points towards the center of the circle.Answer:
D. The acceleration vector of the plant points towards the center of the circle. (Works for Apex)
Explanation:
Velocity is always changing because to have velocity you require direction and the direction is always changing when orbiting therefore A and C are not true. And B is not true because the speed of the planet is not accelerating when orbiting around a star.
Bright and dark fringes are seen on a screen when light from a single source reaches two narrow slits a short distance apart. The number of fringes per unit length on the screen can be doubled:______.
a. if the distance between the slits is doubled.
b. if the wavelength is changed to λ = λ/2.
c. if the distance between the slits is quadruple the original distance and the wavelength is changed to λ = 2λ.
d. if any of the above occurs.
e. only if the width of the slits is changed to w = w/2
Answer:
d. if any of the above occurs
Explanation:
That is The number of fringes per unit length on the screen can be doubled if
if the distance between the slits is doubled.
if the wavelength is changed to λ = λ/2.
And if the distance between the slits is quadruple the original distance and the wavelength is changed to λ = 2λ
From mechanics, you may recall that when the acceleration of an object is proportional to its coordinate, d2xdt2=−kmx=−ω2x , such motion is called simple harmonic motion, and the coordinate depends on time as x(t)=Acos(ωt+ϕ), where ϕ, the argument of the harmonic function at t=0, is called the phase constant. Find a similar expression for the charge q(t) on the capacitor in this circuit. Do not forget to determine the correct value of ϕ based on the initial conditions described in the problem. Express your answer in terms of q0 , L, and C. Use the cosine function in your answer.
Answer:
q = q₀ sin (wt)
Explanation:
In your statement it is not clear the type of circuit you are referring to, there are two possibilities.
1) The circuit of this problem is a system formed by an Ac voltage source and a capacitor, in this case all the voltage of the source is equal to the voltage at the terminals of the capacitor
ΔV = Δ[tex]V_{C}[/tex]
we assume that the source has a voltage of the form
ΔV = ΔV₀o sin wt
The capacitance of a capacitor is
C = q / ΔV
q = C ΔV sin wt
the current in the circuit is
i = dq / dt
i = c ΔV₀ w cos wt
if we use
cos wt = sin (wt + π / 2)
we make this change by being a resonant oscillation
we substitute
i = w C ΔV₀ sin (wt + π/2)
With this answer we see that the current in capacitor has a phase factor of π/2 with respect to the current
2) Another possible circuit is an LC circuit.
In this case the voltage alternates between the inductor and the capacitor
V_{L} + V_{C} = 0
L di / dt + q / C = 0
the current is
i = dq / dt
they ask us for a solution so that
L d²q / dt² + 1 / C q = 0
d²q / dt² + 1 / LC q = 0
this is a quadratic differential equation with solution of the form
q = A sin (wt + Ф)
to find the constant we derive the proposed solution and enter it into the equation
di / dt = Aw cos (wt + Ф)
d²i / dt²= - A w² sin (wt + Ф)
- A w² + 1 /LC A = 0
w = √ (1 / LC)
To find the phase factor, for this we use the initial conditions for t = 0
in the case of condensate for t = or the charge is zero
0 = A sin Ф
Ф = 0
q = q₀ sin (wt)
When an object has a net force of zero, then it is said to be in ____________.
Answer:
Equilibrium
Explanation:
Physics terminology I guess? Equilibrium means that an object isn't moving.
Answer:
Balanced Forces
Explanation:
When forces are in balance, acceleration is zero. Velocity is constant and there is no net or unbalanced force. A plane will fly at constant velocity if the acceleration is zero.
A person is nearsighted with a far point of 75.0 cm. a. What focal length contact lens is needed to give him normal vision
Complete Question
The complete question is shown on the first uploaded image
Answer:
a
[tex]f= -75 \ cm = - 0.75 \ m[/tex]
b
[tex]P = -1.33 \ diopters[/tex]
Explanation:
From the question we are told that
The image distance is [tex]d_i = -75 cm[/tex]
The value of the image is negative because it is on the same side with the corrective glasses
The object distance is [tex]d_o = \infty[/tex]
The reason object distance is because the object father than it being picture by the eye
General focal length is mathematically represented as
[tex]\frac{1}{f} = \frac{1}{d_i} - \frac{1}{d_o}[/tex]
substituting values
[tex]\frac{1}{f} = \frac{1}{-75} - \frac{1}{\infty}[/tex]
=> [tex]f= -75 \ cm = - 0.75 \ m[/tex]
Generally the power of the corrective lens is mathematically represented as
[tex]P = \frac{1}{f}[/tex]
substituting values
[tex]P = \frac{1}{-0.75}[/tex]
[tex]P = -1.33 \ diopters[/tex]
On a part-time job, you are asked to bring a cylindrical iron rod of density 7800 kg/m 3 kg/m3 , length 81.2 cmcm and diameter 2.60 cmcm from a storage room to a machinist. Calculate the weight of the rod, www. Assume the free-fall acceleration is ggg = 9.80 m/s2m/s2 .
Answer:
The weight of the rod is 32.87 N
Explanation:
Density of the rod = 7800 kg/m
length of the rod = 81.2 cm = 0.812 m
diameter of rod = 2.60 cm = 0.026 m
acceleration due to gravity = 9.80 m/s^2
The rod can be assumed to be a cylinder.
The volume of the rod can be calculated as that of a cylinder, and can be gotten as
V = [tex]\frac{\pi d^{2} l}{4}[/tex]
where d is the diameter of the rod
l is the length of the rod
V = [tex]\frac{3.142* 0.026^{2}* 0.812}{4}[/tex] = 4.3 x 10^-4 m^3
We know that the mass of a substance is the density times the volume i.e
mass m = ρV
where ρ is the density of the rod
V is the volume of the rod
m = 4.3 x 10^-4 x 7800 = 3.354 kg
The weight of a substance is the mass times the acceleration due to gravity
W = mg
where g is the acceleration due to gravity g = 9.80 m/s^2
The weight of the rod W = 3.354 x 9.80 = 32.87 N
Tarik winds a small paper tube uniformly with 163 turns of thin wire to form a solenoid. The tube's diameter is 6.13 mm and its length is 2.49 cm . What is the inductance, in microhenrys, of Tarik's solenoid?
Answer:
The inductance is [tex]L = 40\mu H[/tex]
Explanation:
From the question we are told that
The number of turns is [tex]N = 163 \ turns[/tex]
The diameter is [tex]D = 6.13 \ mm = 6.13 *10^{-3} \ m[/tex]
The length is [tex]l = 2.49 \ cm = 0.0249 \ m[/tex]
The radius is evaluated as [tex]r = \frac{d}{2}[/tex]
substituting values
[tex]r = \frac{6.13 *10^{-3}}{2}[/tex]
[tex]r = 3.065 *10^{-3} \ m[/tex]
The inductance of the Tarik's solenoid is mathematically represented as
[tex]L = \frac{\mu_o * N^2 * A }{l }[/tex]
Here [tex]\mu_o[/tex] is the permeability of free space with value
[tex]\mu_o = 4\pi *10^{-7} \ N/A^2[/tex]
A is the area which is mathematically evaluated as
[tex]A = \pi r^2[/tex]
substituting values
[tex]A = 3.142 * [ 3.065*10^{-3}]^2[/tex]
[tex]A = 2.952*10^{-5} \ m^2[/tex]
substituting values into formula for L
[tex]L = \frac{ 4\pi *10^{-7} * [163]^2 * 2.952*10^{-5} }{0.0249 }[/tex]
[tex]L = 40\mu H[/tex]