Among other things, the angular speed of a rotating vortex (such as in a tornado) may be determined by the use of Doppler weather radar. A Doppler weather radar station is broadcasting pulses of radio waves at a frequency of 2.85 GHz, and it is raining northeast of the station. The station receives a pulse reflected off raindrops, with the following properties: the return pulse comes at a bearing of 51.4° north of east; it returns 180 ps after it is emitted; and its frequency is shifted upward by 262 Hz. The station also receives a pulse reflected off raindrops at a bearing of 52.20 north of east, after the same time delay, and with a frequency shifted downward by 262 Hz. These reflected pulses have the highest and lowest frequencies the station receives. (a) Determine the radial-velocity component of the raindrops (in m/s) for each bearing (take the outward direction to be positive). 51.4° north of east ________
52.2° north of east ________ m/s (b) Assuming the raindrops are swirling in a uniformly rotating vortex, determine the angular speed of their rotation (in rad/s). _____________ rad/s

The new speed of the electron as a fraction of c is 0.9655.

Mass of electron = m = 9 x 10⁻³¹ kg

Speed of electron = u = 0.91c

Electric force = F = 1.6 x 10 N

Crossing distance = s = 2 m

Electric force = F = ma

where, F = Electric force, m = Mass of the electron, a = Acceleration of the electron.

Using above equation, we get, a = F/ma = F/m = 1.6 x 10 / 9 x 10⁻³¹ a = 1.78 x 10⁴ m/s²

Now, we can calculate the time taken by electron to travel a distance of 2m using s = ut + ½ at²

where, u = Initial speed of electron, t = Time taken by electron to travel distance s, a = Acceleration of electron, s = Distance travelled by electron.

So, t = s / (u/2 + ½ a)

We get, t = 2 / [0.91c/2 + 1/2 * 1.78 x 10⁴]

= 5.71 x 10⁻¹⁰ s

Kinetic energy = [m / √(1- (v/c)²)] c² - mc²

where, Kinetic energy = Final kinetic energy of electron, m = Mass of the electron, v = Final speed of the electron.

So, K.E = [9 x 10⁻³¹ / √(1-(v/c)²)] c² - (9 x 10⁻³¹) c²

Now, calculate the net work done on the electron. Wnet = K.E - K.Eo

where, Wnet = Net work done on electron, K.E = Final kinetic energy of electron, K.Eo = Initial kinetic energy of electron.

K.Eo = [9 x 10⁻³¹ / √(1-(u/c)²)] c² - (9 x 10⁻³¹) c²

we get, Wnet = [9 x 10⁻³¹ / √(1-(v/c)²)] c² - [9 x 10⁻³¹ / √(1-(u/c)²)] c²

Simplify this expression, Wnet = 0.5 x 9 x 10⁻³¹ [(1/√(1-(v/c)²)] c² - [(1/√(1-(u/c)²)] c²

= 0.5 x m [(1/√(1-(v/c)²)] c² - [(1/√(1-(u/c)²)] c²

Finally, use the work-energy principle. We know that, Wnet = ΔK.E

Wnet = Work done on the particle, ΔK.E = Change in kinetic energy of the particle.

Since the electron is being accelerated, the force acting on it is in the same direction as the direction of motion and hence, the work done is positive. So, we can write Wnet = K.E - K.Eo.

Now, put the values of Wnet, ΔK.E, K.E and K.Eo, we get,0.5 x m [(1/√(1-(v/c)²)] c² - [(1/√(1-(u/c)²)] c²

= [(9 x 10⁻³¹ / √(1-(v/c)²)] c² - [(9 x 10⁻³¹ / √(1-(u/c)²)] c² - [(9 x 10⁻³¹ / √(1-(u/c)²)] c²

Now, we can calculate the final kinetic energy of the electron, Kinetic energy = (Wnet + K.Eo)K.E = 0.5 x m [(1/√(1-(v/c)²)] c² + [(9 x 10⁻³¹ / √(1-(u/c)²)] c²K.E

= [9 x 10⁻³¹ / √(1-(v/c)²)] c²v/c

= √[1 - ((m/m+1)(c/u²t²))]v/c

= √[1 - ((9 x 10⁻³¹/10⁻³¹ + 1)(3 x 10⁸/(0.91 x 3 x 10⁸)² x (5.71 x 10⁻¹⁰)²))]v/c = 0.9655

Therefore, the new speed of the electron as a fraction of c is 0.9655.

Learn more about new speed of electron: https://brainly.com/question/29573654

#SPJ11

The normal force exerted on the sled is 77N. The normal force is the force exerted by a surface perpendicular to the object resting on it.

In this scenario, the man is pulling the sled at a constant speed along a horizontal snow surface. The force he applies is 80 N at an angle of 53° above the surface. To determine the normal force exerted on the sled, we need to consider the forces acting on it.

The normal force is the force exerted by a surface perpendicular to the object resting on it. In this case, since the sled is on a horizontal surface, the normal force is directed vertically upwards to counteract the force of gravity. Since the sled is not accelerating vertically, the normal force is equal in magnitude but opposite in direction to the gravitational force acting on it.

The weight of the sled can be calculated using the equation F = mg, where m is the mass of the sled and g is the acceleration due to gravity (approximately [tex]9.8 m/s^2[/tex]). The weight of the sled is therefore 77 N. Since the sled is not accelerating vertically, the normal force exerted on it must be equal to its weight, which is 77 N.

Learn more about forces here:

https://brainly.com/question/13191643

#SPJ11

The Q-value of the decay is 21.46 MeV.The electron binding energy of 19Ca is 3.210 MeV. Therefore, the maximum kinetic energy of the beta particle is:Kmax = Q – EbKmax = 21.46 MeV – 3.210 MeVKmax = 18.25 MeV

When 19K decays to 19Ca via β− decay, the maximum kinetic energy of the beta particle can be calculated by using the following formula: Kmax = Q – Eb Here, Kmax is the maximum kinetic energy of the beta particle, Q is the Q-value of the decay, and Eb is the electron binding energy of the 19Ca atom.

The Q-value of the decay can be calculated using the mass-energy balance equation.

This equation is given by:m(19K)c² = m(19Ca)c² + melectronc² + QHere, melectronc² is the rest mass energy of the electron, which is equal to 0.511 MeV/c².

Substituting the atomic masses from the periodic table, we get:m(19K) = 18.998 403 163 u, m(19Ca) = 18.973 847 u.

Substituting these values into the equation and simplifying, we get:Q = [m(19K) – m(19Ca) – melectron]c²Q = [18.998 403 163 u – 18.973 847 u – 0.000 548 579 u] × (931.5 MeV/u)Q = 0.023 007 u × (931.5 MeV/u)Q = 21.46 MeV

Therefore, the Q-value of the decay is 21.46 MeV. The electron binding energy of 19Ca is 3.210 MeV. Therefore, the maximum kinetic energy of the beta particle is: Kmax = Q – EbKmax = 21.46 MeV – 3.210 MeVKmax = 18.25 MeV

Therefore, the maximum kinetic energy of the beta particle is 18.25 MeV.

Learn more about beta particle here:

https://brainly.com/question/2193947

#SPJ11

The given toaster is rated at 660 W when it is connected to a 220 V source. We can find the current that the toaster as follows,

P = VI or I=P/V, where P is the power, V is the voltage, I is the current

So, I=660/220

I=3A

Therefore, the current that the toaster carries C. 3.0 A.

Explore a similar question: https://brainly.com/question/24858512

#SPJ11

The rate at which water flows out of the hole in the tank is approximately 1.51×[tex]10^{-3}[/tex] cubic meters per second.

To determine the rate at which water flows out of the hole in the tank, we can apply Bernoulli's equation, which relates the pressure, velocity, and height of a fluid in a flowing system.

First, let's find the velocity of the water flowing out of the hole.

The gauge pressure at the surface of the water is given as 5.00×10^3 Pa.

We can assume atmospheric pressure at the hole, so the total pressure at the hole is the sum of the gauge pressure and atmospheric pressure, which is 5.00×[tex]10^3[/tex] Pa + 1.01×[tex]10^5[/tex] Pa = 1.06×[tex]10^5[/tex] Pa.

According to Bernoulli's equation, the total pressure at the hole is equal to the pressure due to the water column plus the dynamic pressure of the flowing water:

P_total = P_water + (1/2)ρ[tex]v^2[/tex] + P_atm,

where P_total is the total pressure, P_water is the pressure due to the water column, ρ is the density of water, v is the velocity of the water flowing out of the hole, and P_atm is atmospheric pressure.

Since the tank is vertically oriented and the hole is at the bottom, the pressure due to the water column is ρgh, where h is the height of the water column above the hole. In this case, h = 0.900 m.

We can rewrite Bernoulli's equation as:

P_total = ρgh + (1/2)ρ[tex]v^2[/tex] + P_atm.

Now we can solve for v. Rearranging the equation, we get:

(1/2)ρ[tex]v^2[/tex] = P_total - ρgh - P_atm,

[tex]v^2[/tex] = 2(P_total - ρgh - P_atm)/ρ,

v = [tex]\sqrt[/tex](2(P_total - ρgh - P_atm)/ρ).

Now we can plug in the known values:

P_total = 1.06×[tex]10^5[/tex] Pa,

ρ = 1000 kg/[tex]m^3[/tex] (density of water),

g = 9.81 m/[tex]s^2[/tex] (acceleration due to gravity),

h = 0.900 m,

P_atm = 1.01×[tex]10^5[/tex] Pa (atmospheric pressure).

Substituting these values into the equation, we can calculate the velocity v of the water flowing out of the hole.

After finding the velocity, we can then calculate the rate at which water flows out of the hole using the equation for the volume flow rate:

Q = Av,

where Q is the volume flow rate, A is the cross-sectional area of the hole (π[tex]r^2[/tex], where r is the radius of the hole), and v is the velocity of the water.

Let's substitute the known values into the equations to calculate the velocity and volume flow rate.

First, let's calculate the velocity:

v =[tex]\sqrt[/tex](2(P_total - ρgh - P_atm)/ρ)

= [tex]\sqrt[/tex](2((1.06×10^5 Pa) - (1000 kg/m^3)(9.81 m/s^2)(0.900 m) - (1.01×10^5 Pa))/(1000 kg/m^3))

Simplifying the equation:

v ≈ 5.32 m/s

Next, let's calculate the cross-sectional area of the hole:

A = πr^2

= π(0.0190 m/2)^2

Simplifying the equation:

A ≈ 2.84×[tex]10^{-4}[/tex] [tex]m^2[/tex]

Finally, let's calculate the volume flow rate:

Q = Av

= (2.84×[tex]10^{-4}[/tex] [tex]m^2[/tex])(5.32 m/s)

Simplifying the equation:

Q ≈ 1.51×[tex]10^{-3}[/tex] [tex]m^3[/tex]/s

Therefore, the rate at which water flows out of the hole in the tank is approximately 1.51×[tex]10^{-3}[/tex] cubic meters per second.

Learn more about Bernoulli's equation here:

https://brainly.com/question/30509621

#SPJ11

Answer:

The speed of both vehicles after the collision is approximately 14.5 m/s.

Given:

Mass of the truck (m1) = 1890 kg

Mass of the car (m2) = 791 kg

Initial velocity of the truck (v1) = 14.5 m/s

Initial velocity of the car (v2) = 0 m/s (since it is stopped)

Let's denote the final velocity of the truck as v1' and the final velocity of the car as v2'.

Using the conservation of momentum, we can write:

(m1 * v1) + (m2 * v2) = (m1 * v1') + (m2 * v2')

Plugging in the given values:

(1890 kg * 14.5 m/s) + (791 kg * 0 m/s)

= (1890 kg * v1') + (791 kg * v2')

27345 kg·m/s = 1890 kg * v1' + 0 kg·m/s

Now, we can solve for the final velocity of the truck (v1'):

1890 kg * v1' = 27345 kg·m/s

v1' = 27345 kg·m/s / 1890 kg

v1' ≈ 14.5 m/s

The final velocity of the truck (v1') after the collision is approximately 14.5 m/s.

Since the bumpers line up well and no external forces act on the system, the final velocity of the car (v2') will be equal to the final velocity of the truck:

v2' ≈ 14.5 m/s

Therefore, the speed of both vehicles after the collision is approximately 14.5 m/s.

Learn more about conservation of momentum,here

https://brainly.com/question/32309314

The correct answer the magnitude of the resultant electric force on either charge is Option d.9.0 N

Let the original magnitude of one charge be q1 and the original magnitude of the other charge be q2. The original distance between the two charges is r.

The magnitude of the force between two point charges q1 and q2 is given by Coulomb's law as:F=kq1q2/r²Where k is Coulomb's constant which is 9 × 10^9 Nm²/C².Subsequently, if the distance between the two point charges is tripled while the magnitude of both charges is cut in half, the new distance between the two charges is 3r and the new magnitude of both charges is (1/2)q.

The force between the two charges with the new conditions is given by:F'=k((1/2)q)(1/2)q/(3r)²F'=kq²/27r²Since the magnitude of the force between two stationary point charges is the same for each charge, the magnitude of the resultant electric force on either charge is given by:F''=F'/2F''=kq²/54r²The ratio of the new force to the old force is:F''/F=kq/108r².

The magnitude of the force on each charge is:F1=F2=F''/2F1=F2=kq²/108r²The magnitude of the force on each charge is kq²/108r². Answer: d. 9.0 N.

Learn more about electric force here,

https://brainly.com/question/30236242

#SPJ11

This could be an Electric Field. B. This is NOT an Electric Field because: There is no charge represented in the figure; hence, it does not represent an electric field.

The electric force, as well as electric potentials, is given by Coulomb's law. Coulomb's law states that electric force between two charges, Q1 and Q2 is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.

The charges in this question are explicit in Q17, 21 & implicit in Q18-20. Let's discuss the circles. Circles A and B are simple force-potential figures. Circle A is a graphical representation of electric field lines. This is because the arrows show the direction of force that would be exerted on a unit charge at every point, and the density of lines indicates the strength of the electric field.

On the other hand, circle B shows equipotential lines. This is because the lines are parallel to each other and the potential difference between them is constant. If circle B showed electric field lines, the arrows would be perpendicular to the equipotential lines, whereas in this figure, the lines are not perpendicular. Hence, the lines in circle B are not electric field lines.

It is essential to understand that equipotential lines always cross at right angles. Circle A: 17. Simple Force Potential Question A. This could be an Electric Field. B. This is an Electrie Field because: It is a typical electric field with its field lines emerging from the positive charges and terminating at the negative charges. Circle B: 18. Simple Force Potential Question A.

This could be an Electric Field. B. This is NOT an Electric Field because: The parallel lines in the graph indicate equipotential lines and not electric field lines. Circle A: 19. Simple Force Potential Question A. This could be an Electnc Field. B. This is NOT an Electric Field because: The arrows represent force and the density of lines shows the electric field strength,

which is lacking in the figure. Circle B: 20. Simple Force Potential Question A. This could be an Electne Freld. B. This is NOT an Electric Field because: The parallel lines represent equipotential lines, which are perpendicular to electric field lines. Circle A: 21. Simple Force Potential Question A.

This could be an Electric Field. B. This is NOT an Electric Field because: There is no charge represented in the figure; hence, it does not represent an electric field.

to know more about Electric

https://brainly.com/question/2969220

#SPJ11

The magnitude of the field is 1.41 × 10^-3 T.

When a charged particle moves in a magnetic field perpendicular to the magnetic field, the Lorentz force acts as a centripetal force causing the charged particle to move in a circle. The centripetal force is given by the relation: F = ma = (mv²)/r.

Where m is the mass of the charged particle, v is the velocity of the charged particle, r is the radius of the circle and a is the acceleration of the charged particle due to the magnetic field.Based on the information given in the question;Mass of the electron, m = 9.1 × 10^-31 kgVelocity of the electron, v = 4.9 × 10^5 m/s.

Radius of the circle, r = 1.0 cm = 0.01 mThe force acting on the electron due to the magnetic field is given by the relation: F = qvB. Where q is the charge of the electron, v is the velocity of the electron and B is the magnetic field strength.

Since the force acting on the electron is the centripetal force, equating these two forces we get: F = mv²/r = qvB. Therefore, B = mv/rq = (9.1 × 10^-31 kg × (4.9 × 10^5 m/s))/((0.01 m) × 1.6 × 10^-19 C) = 1.41 × 10^-3 T.So, the magnitude of the magnetic field is 1.41 × 10^-3 T.Answer: The magnitude of the field is 1.41 × 10^-3 T.

Learn more about magnitude here,

https://brainly.com/question/30337362

#SPJ11

Dividing the wavelength in air (558 nm) by the wavelength in the liquid (420 nm) will give the refractive index. The liquid's index of refraction is 1.33. The speed of light in liquid is  [tex]2.26 x 10^8 m/s.[/tex]

(a) To calculate the refractive index of the liquid, we can use the formula: n = λ_air / λ_liquid

Substituting the given values of λ_air = 558 nm and λ_liquid = 420 nm into the formula, we have:

n = [tex]\frac{558}{420}[/tex]

Calculating the value:

n = 1.33

Therefore, the index of refraction of the liquid is approximately 1.33.

(b) To find the speed of light in the liquid, we can use the equation:

v = c / n

where v is the speed of light in the medium, c is the speed of light in a vacuum, and n is the index of refraction of the medium.

v = [tex]\frac{(3.0 x 10^8 m/s)}{1.33}[/tex]

Calculating the value:

v ≈ [tex]2.26 x 10^8 m/s[/tex]

Therefore, the speed of light in the liquid is approximately [tex]2.26 x 10^8 m/s.[/tex]

Learn more about refractive index here:

https://brainly.com/question/30761100

#SPJ11

A plastic light pipe has an index of refraction of 1.66. for both (a) air and (b) water as the initial medium, total internal reflection does not occur when light enters the plastic light pipe with a refractive index of 1.66.

To determine the critical angle for total internal reflection, we can use Snell's law, which relates the angles of incidence and refraction at the interface between two media:

n1 × sin(theta1) = n2 × sin(theta2)

where:

n1 is the refractive index of the first medium (initial medium),

theta1 is the angle of incidence,

n2 is the refractive index of the second medium (final medium), and

theta2 is the angle of refraction.

For total internal reflection, the angle of refraction (theta2) becomes 90 degrees. Therefore, we can rewrite Snell's law as:

n1 × sin(theta1) = n2 × sin(90)

Since sin(90) = 1, the equation simplifies to:

n1 × sin(theta1) = n2

(a) Air as the initial medium:

Given n1 = 1 (approximating the refractive index of air as 1) and n2 = 1.66 (refractive index of the plastic light pipe), we can rearrange the equation to solve for sin(theta1):

sin(theta1) = n2 / n1

sin(theta1) = 1.66 / 1

sin(theta1) = 1.66

However, the sine of an angle cannot be greater than 1. Therefore, there is no critical angle for total internal reflection when light travels from air to the plastic light pipe. Total internal reflection does not occur in this case.

(b) Water as the initial medium:

Given n1 = 1.33 (refractive index of water) and n2 = 1.66 (refractive index of the plastic light pipe), we can use the same equation to find sin(theta1):

sin(theta1) = n2 / n1

sin(theta1) = 1.66 / 1.33

sin(theta1) ≈ 1.248

To find the angle theta1, we can take the inverse sine of sin(theta1):

theta1 = arcsin(sin(theta1))

theta1 ≈ arcsin(1.248)

However, since the sine of an angle cannot exceed 1, there is no real solution for theta1 in this case. Total internal reflection does not occur when light travels from water to the plastic light pipe.

Therefore, for both (a) air and (b) water as the initial medium, total internal reflection does not occur when light enters the plastic light pipe with a refractive index of 1.66.

To learn more about total internal reflection visit: https://brainly.com/question/13088998

#SPJ11

The capacitance of the parallel-plate capacitor is approximately 5.31 x 10⁻¹¹ F or 53.1 pF. To find the capacitance of a parallel-plate capacitor, we can use the formula:

C = (ε₀ * εᵣ * A) / d

where:

C is the capacitance,

ε₀ is the vacuum permittivity (8.854 x 10⁻¹² F/m),

εᵣ is the relative permittivity or dielectric constant (given as 11.1),

A is the area of the plates (2.0 cm by 3.0 cm = 0.02 m * 0.03 m = 0.0006 m²),

d is the separation between the plates (1.0 mm = 0.001 m).

Plugging in the values, we have:

C = (8.854 x 10⁻¹² F/m * 11.1 * 0.0006 m²) / 0.001 m

= 5.31 x 10⁻¹¹ F

Therefore, the capacitance of the parallel-plate capacitor is approximately 5.31 x 10⁻¹¹ F or 53.1 pF.

For the second part of the question, when two identical drops combine to form a larger drop, the total capacitance is given by the sum of the individual capacitances:

C_total = C1 + C2

Since each individual drop has a capacitance of C, we have:

C_total = C + C = 2C

Therefore, the capacitance of the single larger drop formed by combining two identical drops is 2 times the original capacitance, which is 2C. In this case, it is given that C = 4πER, so the capacitance of the single larger drop is 2 times that:

C_total = 2C = 2(4πER) = 8πER

Hence, the capacitance of the single larger drop is 8πER.

To know more about the vacuum permittivity

brainly.com/question/31484434

#SPJ11

The maximum safe depth of the submarine is approximately 10,317 meters can be determined by calculating the pressure exerted on the window and comparing it to the manufacturer's stated limit.

To calculate the maximum safe depth of the submarine, we need to consider the pressure exerted on the window. The pressure exerted by a fluid is given by the equation P = ρgh, where P is the pressure, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the depth. In this case, the fluid is seawater.

First, we need to determine the pressure exerted on the window at the maximum safe depth. The pressure inside the submarine is maintained at 1.0 atm, which is equivalent to 101,325 Pa. We can assume that the density of seawater is approximately [tex]1,030 kg/m^3[/tex] and the acceleration due to gravity is [tex]9.8 m/s^2[/tex].

Using the equation P = ρgh, we can rearrange it to solve for h: h = P / (ρg). Plugging in the values, we have h = [tex]101,325 Pa / (1,030 kg/m^3 * 9.8 m/s^2)[/tex], which gives us the maximum safe depth of the submarine.

To find out the numerical value, we need to evaluate the expression. The maximum safe depth of the submarine is approximately 10,317 meters.

Learn more about acceleration due to gravity here:

https://brainly.com/question/29135987

#SPJ11

Answer:

The frequency at which the 6.0 mH inductor and 10 nF capacitor have the same reactance is approximately 20,462 Hz.

Reactance of an inductor (XL) is given by:

XL = 2πfL

Reactance of a capacitor (XC) is given by:

XC = 1 / (2πfC)

Where f is the frequency, L is the inductance, and C is the capacitance.

Setting XL equal to XC:

2πfL = 1 / (2πfC)

Simplifying the equation:

f = 1 / (2π√(LC))

L = 6.0 mH

= 6.0 x 10^(-3) H

C = 10 nF

= 10 x 10^(-9) F

Substituting the given values into the equation:

f = 1 / (2π√(6.0 x 10^(-3) H * 10 x 10^(-9) F))

Simplifying the expression:

f = 1 / (2π√(60 x 10^(-12) H·F))

f = 1 / (2π√(60 x 10^(-12) s^2 / C^2))

f = 1 / (2π x 7.75 x 10^(-6) s)

f ≈ 20,462 Hz

Therefore, the frequency at which the 6.0 mH inductor and 10 nF capacitor have the same reactance is approximately 20,462 Hz.

To show that this frequency is the natural frequency of an oscillating circuit with the same L and C, we can use the formula for the natural frequency of an LC circuit:

fn = 1 / (2π√(LC))

Substituting the given values into the formula:

fn = 1 / (2π√(6.0 x 10^(-3) H * 10 x 10^(-9) F))

fn = 1 / (2π√(60 x 10^(-12) H·F))

fn = 1 / (2π√(60 x 10^(-12) s^2 / C^2))

fn = 1 / (2π x 7.75 x 10^(-6) s)

fn ≈ 20,462 Hz

We can see that this frequency matches the frequency obtained earlier, confirming that it is the natural frequency of an oscillating circuit with the same L and C.

Learn more about capacitance, here

https://brainly.com/question/30529897

#SPJ11

The final velocities of the two vehicles, if the collision is elastic, then v₁ = 18 m/s and v₂ = 48 m/s.

It is given that, Mass of car, m₁ = 750 kg, Initial velocity of car, u₁ = 23 m/s, Mass of truck, m₂ = 1250 kg, Initial velocity of truck, u₂ = 15 m/s and the collision is elastic. Therefore, the total momentum of the system is conserved, i.e.,

m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂

Putting the values, we get,

750 × 23 + 1250 × 15 = 750v₁ + 1250v₂

(17250 + 18750) = (750v₁ + 1250v₂)

36000 = 750v₁ + 1250v₂

(6 × 6000) = 750v₁+ 1250v₂

Now, we have two variables and only one equation. We need another equation. We can use the conservation of kinetic energy to get another equation.

Since the collision is elastic, the total kinetic energy of the system is conserved, i.e.,

(1/2)m₁*2u₁ + (1/2)m₂*2u₂ = (1/2)m₁*2v₁ + (1/2)m₂*2v₂

Putting the values, we get,

(1/2) × 750 × (23)2 + (1/2) × 1250 × (15)2 = (1/2) × 750 × 2v₁ + (1/2) × 1250 × 2v₂

Solving further, we get,

195375 = 375v₁ + 937.5v₂(195375 / 375) = v₁ + (937.5 / 375)v₂(521 / 5) = v₁ + (25 / 2)v₂

Multiplying the first equation by 25 and subtracting the second equation, we get,

15000 = (625/2)v₂

v₂ = 48 m/s

Putting the value of v₂ in the first equation, we get,

6 × 6000 = 750v1 + 1250(48)

v₁ = 18 m/s

Therefore, the final velocities of the two vehicles are:v₁ = 18 m/s , v₂= 48 m/s.

To learn more about velocity: https://brainly.com/question/80295

#SPJ11

At t=0 a grinding wheel has an angular velocity of 26.0 rad/s. It has a constant angular acceleration of 31.0 rad/s until a circuit breaker trips at time t = 1.50 s and it turns through an angle 433 rad, then the total angle with which the wheel turn between t=0 and the time stopped is θ = 227.012 rad and the time at which it stops is t= 7.79 s.

A grinding wheel has an initial angular velocity, ω₁ = 26.0 rad/s, Constant angular acceleration, α = 31.0 rad/s², Time after which the circuit breaker,

Let, the final angular velocity of the wheel be ω₂.

Final angular velocity, ω₂ = 0 rad/s

a)

We need to find the total angle through which the wheel turns between t = 0 and the time it stops.

Total angle through which the wheel turns between t = 0 and the time it stops is given by,

θ = θ₁ + θ₂

where, θ₁ = angle moved by the wheel before circuit breaker trips, θ₂ = angle moved by the wheel after circuit breaker trips

θ₁ = ω₁t + 1/2 αt²

where, ω₁ = initial angular velocity, t = time taken for circuit breaker to trip, α = angular acceleration

θ₁ = 26.0(1.50) + 1/2(31.0)(1.50)²= 113.625 rad

θ₂ = ω² - ω²/2α

where,ω = initial angular velocity = 26.0 rad/s

ω₂ = final angular velocity = 0 rad/s

α = angular acceleration= 31.0 rad/s²

θ₂ = (26.0)²/2(31.0)= 114.387 rad

Total angle through which the wheel turns between t = 0 and the time it stops,

θ = θ₁ + θ₂= 113.625 + 114.387= 227.012 rad

Therefore, the total angle through which the wheel turns between t = 0 and the time it stops is 227.012 rad.

b) We need to find the time at which it stops.

Using the relation,

θ = ω₁t + 1/2 αt²θ - ω₁t = 1/2 αt²t = √2(θ - ω₁t)/α

At t = 0, the wheel has an angular velocity, ω₁ = 26.0 rad/s

So,The time it stops, t = √2(θ - ω₁t)/α= √2(433 - 26.0(1.50))/31.0= 7.79 s

Therefore, the wheel stops at t = 7.79 s.

To learn more about acceleration: https://brainly.com/question/460763

#SPJ11

a) When an electron in a hydrogen atom transitions from the n=3 to the n=1 energy level, the wavelength of light emitted can be calculated using the Rydberg formula: 1/λ = R_H * (1/n_1^2 - 1/n_2^2), where λ is the wavelength, R_H is the Rydberg constant for hydrogen (approximately 1.097 × 10^7 m^-1), n_1 is the initial energy level (n=3), and n_2 is the final energy level (n=1).

b) The cut-off wavelength of lead (Pb) can be determined based on the work function, which is the minimum energy required to remove an electron from the metal surface. The relationship between the cut-off wavelength (λ_cutoff) and the work function (Φ) is given by λ_cutoff = hc / Φ, where h is Planck's constant (approximately 6.626 × 10^-34 J·s) and c is the speed of light (approximately 3.00 × 10^8 m/s). By substituting the value of the work function (4.25 eV) into the equation, we can calculate the cut-off wavelength of lead.

c) Once the wavelength of the emitted light from part a) is known, the velocity of the emitted electrons can be determined using the de Broglie wavelength equation: λ = h / mv, where m is the mass of the electron and v is its velocity. By rearranging the equation, we can solve for the velocity: v = h / (mλ). By substituting the mass of an electron and the calculated wavelength into the equation, we can find the velocity of the emitted electrons.

Learn more about the Rydberg formula, here:

https://brainly.com/question/32818875

#SPJ11

To find the intensity of an electromagnetic wave, we need to know the electric and magnetic field strengths as they are interdependent. The correct option is 1) Both the electric and magnetic field strengths.

The intensity of an electromagnetic wave is given by the energy transferred per unit area per unit time and is proportional to the square of the electric and magnetic field strengths. Therefore, if either the electric or magnetic field strength is missing, it will be impossible to determine the intensity accurately. The electric and magnetic fields oscillate perpendicular to each other and the direction of propagation of the wave. They have the same amplitude, frequency, and wavelength, but they differ in phase.

The intensity of an electromagnetic wave can also be determined by measuring the average power per unit area over a period. In summary, both electric and magnetic field strengths are required to calculate the intensity of an electromagnetic wave accurately. It is important to note that these fields are interdependent on each other, and a change in one can affect the other. Therefore, accurate measurements are crucial in the determination of the intensity of electromagnetic waves.

Learn more about electromagnetic wave here:

https://brainly.com/question/29774932

#SPJ11

The speed of the object when it is at x = -1.5 m is 7.0 m/s. Answer: a. 7.0 m/s.

Given data,A = -3.7 mω = 2.0 rad/st = ?θ = 0.20 radWe know that velocity as a function of time is given by the derivative of position as a function of time, that is,v(t) = d/dt [x(t)]v(t) = d/dt [Asin(ωt + θ)]v(t) = Aω cos(ωt + θ)Now, the position of the object is given byx(t) = Asin(ωt + θ)Now, substituting the given values, we getx(t) = -3.7 sin(2t + 0.20) mNow, the object is at x = -1.5 mHence, -1.5 = -3.7 sin(2t + 0.20)Solving for t, we gett = 0.835 sNow, substituting t = 0.835 s in the equation of velocity as a function of time, we getv(t) = Aω cos(ωt + θ)v(t) = -3.7 × 2.0 cos(2(0.835) + 0.20) m/sv(t) = -7.0 m/sTherefore, the speed of the object when it is at x = -1.5 m is 7.0 m/s. Answer: a. 7.0 m/s.

Learn more about Velocity here,

https://brainly.com/question/80295

#SPJ11

You should advise the captain to set a heading angle of approximately 63.43 degrees from your current position towards the destination port.

To determine the heading angle from your current position to the destination port, you can use trigonometry. Given that your current position is 50.0 km north and 25.0 km east of the origin port, you can consider these values as the lengths of the legs of a right triangle.

The desired heading angle can be found using the tangent function, which is defined as the ratio of the opposite side to the adjacent side in a right triangle. In this case, the opposite side is the northward distance (50.0 km) and the adjacent side is the eastward distance (25.0 km).

The heading angle (θ) can be calculated as:

θ = tan^(-1)(opposite/adjacent)

θ = tan^(-1)(50.0 km/25.0 km)

Using a calculator, the approximate value of the heading angle is:

θ ≈ 63.43 degrees

To know more about trigonometry

https://brainly.com/question/11016599

#SPJ11

The maximum speed attained by the object is approximately 0.19 m/s. To calculate the amplitude of the motion, we can use the formula:

A = [tex]x_{max[/tex]

where A is the amplitude and [tex]x_{max[/tex] is the maximum displacement from the equilibrium position.

Given that the object is 0.019 m from its equilibrium position, we can conclude that the amplitude is also 0.019 m.

So, the amplitude of the motion is 0.019 m.

To calculate the maximum speed attained by the object, we can use the equation:

[tex]v_{max[/tex] = ω * A

where [tex]v_{max[/tex] is the maximum speed, ω is the angular frequency, and A is the amplitude.

The angular frequency can be calculated using the formula:

ω = √(k / m)

where k is the spring constant and m is the mass.

Given that the spring constant is 310 N/m and the mass is 3.2 kg, we can calculate ω:

ω = √(310 N/m / 3.2 kg)

≈ √(96.875 N/kg)

≈ 9.84 rad/s

Now we can calculate the maximum speed:

[tex]v_{max[/tex] = 9.84 rad/s * 0.019 m

≈ 0.19 m/s

Therefore, the maximum speed attained by the object is approximately 0.19 m/s.

To learn more about maximum speed visit:

brainly.com/question/10236290

#SPJ11

A heat engine with completely frictionless parts would still not be 100% efficient even if it ran on the Carnot cycle.

Suppose you try to cool the kitchen of your house by leaving the refrigerator door open. What happens? Why?Would the result be the same if you left open a picnic cooler full of ice? Explain the reason for any differences.If you leave the refrigerator door open, the room may become slightly colder initially, but the overall effect will be to warm up the room. This is because the refrigerator will work to cool down the air inside it but at the same time will pump the heat out into the room. As a result, the room’s temperature will rise. If you left a picnic cooler full of ice open in the room, the ice would eventually melt and the water would eventually warm up to room temperature, raising the temperature of the room.

However, the cooling effect of the ice will be greater than the heating effect of the air that escapes. Therefore, it will be more efficient in cooling the room for a shorter time.Is it a violation of the second law of thermodynamics to convert mechanical energy completely into heat? To convert heat completely into work? Explain your answers.No, it is not a violation of the second law of thermodynamics to convert mechanical energy completely into heat because heat is a form of energy, and the second law of thermodynamics states that energy cannot be created or destroyed; it can only be transferred or converted from one form to another.

However, it is impossible to convert heat completely into work because some heat energy will always be lost to the environment, and the second law of thermodynamics prohibits the conversion of heat energy completely into work.Real heat engines, like the gasoline engine in a car, always have some friction between their moving parts, although lubricants keep the friction to a minimum. Would a heat engine with completely frictionless parts be 100% efficient? Why or why not? Does the answer depend on whether or not the engine runs on the Carnot cycle?

Again, why or why not?A heat engine with completely frictionless parts would not be 100% efficient because some energy would still be lost as heat due to the second law of thermodynamics. The answer does not depend on whether or not the engine runs on the Carnot cycle because the Carnot cycle assumes an ideal engine with no friction, which is not possible in the real world. Therefore, a heat engine with completely frictionless parts would still not be 100% efficient even if it ran on the Carnot cycle.

Learn more about Thermodynamics here,

https://brainly.com/question/13059309

#SPJ11

The total resistance of the combination of resistors is 1250 Ω.

To get the total resistance of a combination of resistors that are connected in a row, it is essential to follow these two steps:Add all the resistors values together to get the equivalent resistance. In this case,

AB = A + B = 150 Ω + 730 Ω = 880 Ω ABC = AB + C = 880 Ω + 370 Ω = 1250 Ω

Therefore, the total resistance of the combination of resistors is 1250 Ω.

This means that the flow of current through the resistors will face the resistance of 1250 Ω, which will limit the flow of the current to some extent.

Know more about resistance here,

https://brainly.com/question/32301085

#SPJ11

Activation polarization is a mechanism that influences the corrosion rate, and it is the activation energy of the electrochemical reaction that determines the total reaction rate.

Activation polarization refers to the increase in the electrochemical reaction rate caused by the energy barrier, known as activation energy, that needs to be overcome for the reaction to proceed. The total reaction rate in corrosion is determined by the activation energy, which represents the minimum energy required for the reaction to occur.

In the context of corrosion, activation polarization occurs at the electrode-electrolyte interface. It is caused by various factors such as the nature of the corroding material, composition of the electrolyte, temperature, and presence of inhibitors. Activation polarization affects the rate of electrochemical reactions involved in the corrosion process.

When the activation energy is high, the reaction rate is low, leading to slower corrosion. On the other hand, when the activation energy is low, the reaction rate is high, resulting in faster corrosion. Therefore, the activation energy, which determines the activation polarization, plays a critical role in determining the total reaction rate of corrosion.

To know more about Activation polarization click here:

https://brainly.com/question/28963605

#SPJ11

Therefore, the force required to accelerate a mass of 7 kg at a rate of 17 m/s² is approximately 26.78 lb.

To calculate the force required to accelerate a mass of 7 kg at a rate of 17 m/s², you can use the formula F = ma, where F is the force in newtons, m is the mass in kilograms, and a is the acceleration in meters per second squared. Since the question asks for the force in lb, we will need to convert the result from newtons to pounds.

First, we can calculate the force in newtons by multiplying the mass by the acceleration: F = 7 kg x 17 m/s² = 119 N.

To convert newtons to pounds, we can use the conversion factor 1 N = 0.2248 lb. Therefore, the force required to accelerate a mass of 7 kg at a rate of 17 m/s² is:

F = 119 N x 0.2248 lb/N = 26.78 lb.

Therefore, the force required to accelerate a mass of 7 kg at a rate of 17 m/s² is approximately 26.78 lb.

To know more about force visit:

https://brainly.com/question/28854893

#SPJ11

The ship's dimensions in the x-axis are approximately 676.2 m (length) and D₀ (diameter), and its dimensions in the y-axis remain the same as D₀ when it is moving and when it lands.

To solve for the dimensions of the ship along the x- and y-axis, we can use the concept of length contraction in special relativity. According to special relativity, objects moving at high speeds relative to an observer undergo length contraction in the direction of their motion.

Let's denote the ship's dimensions in its rest frame (ship's frame) as L₀ (length) and D₀ (diameter). We want to find the dimensions of the ship as observed by a person on Earth when it is moving at a speed of 0.90c.

The length contraction factor, γ, can be calculated using the Lorentz factor:

γ = 1 / sqrt(1 - (v/c)^2)

Where v is the velocity of the ship and c is the speed of light.

Given that v = 0.90c, we can calculate γ:

γ = 1 / sqrt(1 - (0.90)^2)

Using a calculator, we find γ ≈ 2.94.

Now, let's consider the length contraction along the direction of motion (x-axis):

L = L₀ / γ

Substituting the given length (L) as 230 m, we can solve for L₀:

230 m = L₀ / 2.94

Solving for L₀, we find L₀ ≈ 676.2 m.

Therefore, the ship's length in its frame is approximately 676.2 m.

Next, let's consider the diameter along the y-axis. According to length contraction, there is no contraction in directions perpendicular to the motion. Therefore, the diameter of the ship remains the same:

D = D₀

Since no length contraction occurs along the y-axis, the ship's diameter remains unchanged.

The ship's dimensions in the x-axis are approximately 676.2 m (length) and D₀.

To know more about velocity

https://brainly.com/question/30559316

#SPJ11

Choice D, all of the above, is the correct answer. For the third question, the correct statement is: W = FΔd cosθ.Work is a scalar quantity that represents the transfer of energy that occurs when a force is applied to an object and it moves through a distance.

Impulse has the same SI units as momentum. Impulse and momentum share the same SI units, which are kg m/s. Impulse and momentum are also related to each other. Impulse is defined as the change in momentum of an object. Impulse = Δp = mΔvMomentum = p = mvwhere m is the mass of the object and v is its velocity.Work, linear momentum, and kinetic energy are not equivalent to impulse. They have different SI units and meanings.Work is the transfer of energy that occurs when a force is applied to an object and it moves through a distance. Its SI units are joules (J).Linear momentum is the product of an object's mass and velocity. Its SI units are kg m/s.Kinetic energy is the energy an object has due to its motion. Its SI units are also joules (J).For the second question, momentum is conserved when an insect collides with the windshield of a moving car, an electron splits an atom into many subatomic particles, a rifle fires a bullet and the gun recoils. Choice D, all of the above, is the correct answer. For the third question, the correct statement is: W = FΔd cosθ.Work is a scalar quantity that represents the transfer of energy that occurs when a force is applied to an object and it moves through a distance. It is calculated using the formula W = FΔd cosθ, where F is the force applied, Δd is the displacement of the object, and θ is the angle between the force and the displacement.

To know more about momentum visit:

https://brainly.com/question/899725

#SPJ11

If one of the light bulb burns out, Total resistance increases, other bulbs get dimmer. The circuit would not be broken if one of the bulbs burns out. This is the effect of a parallel circuit when one component fails. Therefore. the correct answer is option B.

In a parallel circuit, each device operates independently. As a result, if one component fails, it does not cause the others to stop working. However, since the resistance of each bulb is fixed, the total resistance of the circuit decreases as bulbs are added.

When a bulb burns out, the resistance of the circuit rises, making the other bulbs dimmer. Because the current in a parallel circuit is divided among the components, the current flowing through each remaining bulb would decrease if one bulb burns out.

So, if one bulb fails, the voltage across it would drop, and it would get dimmer. That's why in parallel circuit the bulbs are installed in parallel to ensure that they function independently of each other. So, option B is the correct answer.

To learn more about resistance: https://brainly.in/question/19540047

#SPJ11

The light-emitting diode (LED) is a two-terminal semiconductor light source used as a light source in lighting. The wavelength of the emitted light from the LED is 1240.

An LED (light-emitting diode) is made up of a p-n junction made of a particular semiconducting substance with a bandgap of 1.61 eV. The wavelength of the emitted light is given in this question and needs to be calculated.

The energy of the photon is related to the wavelength λ by the formula,

E = hc/λ

where E is the photon energy, h is Planck's constant, and c is the speed of light.

The formula can be modified to find the wavelength of the emitted light:

λ = hc/E

where λ is the wavelength, h is Planck's constant, c is the speed of light, and E is the energy of a photon.

The energy gap of the p-n junction of an LED determines the energy and frequency of the photon emitted.

The energy gap is given in the question to be 1.61 eV.

h and c are constants that are well-known.

The value of h is 6.626 x 10-34 joule-second, and c is 2.998 x 108 meter/second.

Substituting the values,

λ = hc/Eλ

= (6.626 x 10-34) x (2.998 x 108) / (1.61 x 1.6 x 10-19)λ

= 1.24 x 10-6 meter

= 1240 nm

Therefore, the wavelength of the emitted light from the LED is 1240 nm.

Learn more about semiconductor: https://brainly.com/question/30762286

#SPJ11

The phenomenon of EM waves composed of individual spherical particles that form the resulting wavefront is referred to as Huygens Principle.

Christiaan Huygens was a Dutch scientist who suggested in 1678 that every point on the primary wavefront acts as a source of secondary waves. These secondary waves are spherical waves that propagate at the same speed and frequency as the primary wave, but with different amplitudes and phases.Huygens principle aids in determining how waves behave when they interact with obstacles. It allows us to predict how a wave will propagate through a given geometry by imagining it as the sum of secondary wavelets produced by the primary wave.

To know more about wave visit:

https://brainly.com/question/14082910

#SPJ11