a person views his face in a 20- cm focal length concave mirror. where should his face be in order to form an upright image that is magnified by a factor of 1.7?

The inductance of one conductor in the unstretched cord is 1.28 x 10^-7 H.

When a coiled telephone cord forms a spiral with 74.0 turns, a diameter of 1.30 cm, and an unstretched length of 45.0 cm, we need to determine the inductance of one conductor in the unstretched cord.

Diameter (d) = 1.30 cm

Radius (r) = d/2 = 0.65 cm = 0.0065 m

Length (l) = 45.0 cm = 0.45 m

From the formula for the area of a circle;

A = πr²A = π(0.0065 m)² = 1.327 x 10^-4 m²

To determine the inductance of one conductor in an unstretched cord, we need to use the formula for inductance of a solenoid that is given;

L = [μN²A]/l

where;

L = inductance of the solenoid

N = number of turns of the coil = 74.0 turns

A = area of the coil in m²

μ = permeability of free space

l = length of the coil

L = [μN²A]/lL = [4π x 10^-7 (74.0)^2 (1.327 x 10^-4)]/0.45L = 1.28 x 10^-7 H

Therefore, the inductance of one conductor in the unstretched cord is 1.28 x 10^-7 H.

To know more about inductance click here:

https://brainly.com/question/29981117

#SPJ11

Answer:

Approximately [tex](-2.54) \times 10^{-5}\; {\rm C}[/tex].

Explanation:

The magnitude of the electric field around a point charge can be found with the equation:

[tex]\begin{aligned} E &= \frac{k\,q}{r^{2}}\end{aligned}[/tex], where:

Rearrange this equation and solve for the magnitude [tex]q[/tex] of this point charge:

[tex]\begin{aligned}q &= \frac{r^{2}\, E}{k} \\ &= \frac{(60.7)^{2}\, (61.9)}{8.98755}\; {\rm C} \\ &\approx 2.54\times 10^{-5}\; {\rm C}\end{aligned}[/tex].

Note that the sign of electric charges can be either positive or negative. The direction of field lines around this point charge provides info on the sign of this electric charge.

By convention, the direction of electric field lines at a particular position is the same as the direction of the force on a positive electric test charge at that location. Since the electric field around this point charge points towards the charge, it means a positive charge would be attracted to this point charge.

Charges of opposite signs attract each other. For the point charge in this question to attract a positive test charge, it must be true that this point charge has a negative sign. Hence, this point charge would be [tex](-2.54) \times 10^{-5}\; {\rm C}[/tex].

The effective resistance  of a car's starter motor is: Resistance = 0.0729 Ω

Using Ohm's law, we can find the effective resistance of the car's starter motor. Ohm's law states that resistance is equal to voltage divided by current.

[tex]Resistance = Voltage / Current\\Resistance = 10.5 V / 144 A\\Resistance = 0.0729\ ohm[/tex]

Therefore, the effective resistance of the car's starter motor is 0.0729 Ω. This means that the starter motor will draw a large amount of current from the battery when it is running, but only a small voltage is required to keep the current flowing through the motor. The low resistance of the starter motor allows it to draw a large amount of power from the battery, which is necessary to turn the engine over and start the car.

To know more about Ohm's law, here

brainly.com/question/1247379

#SPJ4

The kinetic energy of the baseball when thrown by a major-league pitcher at 95.0 mph is approximately 136.22 Joules.

The kinetic energy (KE) of an object can be calculated using the formula KE = 0.5 * m * v^2, where m is the mass in kilograms, and v is the velocity in meters per second.

First, we need to convert the mass from ounces to kilograms and the velocity from miles per hour to meters per second.

1 oz = 0.0283495 kg

5.13 oz * 0.0283495 = 0.14515 kg

1 mph = 0.44704 m/s

95.0 mph * 0.44704 = 42.4698 m/s

Now, we can calculate the kinetic energy:

KE = 0.5 * 0.14515 kg * (42.4698 m/s)^2

KE ≈ 136.22 Joules

For more such questions on kinetic energy, click on:

https://brainly.com/question/29763149

#SPJ11

While using absorbance values at wavelengths other than the optimal wavelength could still result in a value of k that is close to the optimal value, it is important to consider the potential limitations and uncertainties associated with using different wavelengths.

Wavelengths refer to the distance between successive peaks or troughs of a wave. They are a fundamental concept in physics and are commonly used to describe various types of waves, including electromagnetic waves, sound waves, and water waves.

Electromagnetic waves, such as light, radio waves, and X-rays, have different wavelengths that determine their properties and behavior. For example, visible light has a range of wavelengths that correspond to different colors, with longer wavelengths appearing as red and shorter wavelengths appearing as violet. In sound waves, wavelength is related to the frequency of the wave, which determines the pitch of the sound. Higher frequencies correspond to shorter wavelengths and higher-pitched sounds, while lower frequencies correspond to longer wavelengths and lower-pitched sounds.

To learn more about Wavelengths visit here:

brainly.com/question/13533093

#SPJ4

"A capacitor is constructed of two identical conducting plates parallel to each other and separated by a distance d. The capacitor is charged to a potential difference of v₀ by a battery, which is then disconnected. a sheet of insulating plastic material is inserted between the plates without otherwise disturbing the system. It causes the capacitance to increase."

A device for holding separated charge is a capacitor.

Until the voltage created by the charge buildup is equivalent to the battery voltage, a battery will transfer charge from one plate to the other.

If the battery is disconnected, Q remains constant. The capacitance rises if a dielectric is placed in between the plates.

This can be said because of the equation, Q = C V

where, Q is charge in coulombs

V is voltage

C is capacitance

Thus, the capacitance increases.

To know more about capacitor:

https://brainly.com/question/13480989

#SPJ4

The thermal efficiency of the heat engine propelling the ship is approximately 64.29%. This means that about 64.29% of the heat input is converted into useful work to propel the ship, while the remaining 35.71% is rejected as waste heat.

The thermal efficiency of a heat engine is a measure of how effectively it converts heat energy into mechanical work. In the given student question, a ship's heat engine produces 540 BTU/lbm of work and rejects 300 BTU/lbm of heat.

To calculate the thermal efficiency, we need to know the total heat input, which is the sum of work output and heat rejected.

Total heat input = Work output + Heat rejected
Total heat input = 540 BTU/lbm + 300 BTU/lbm
Total heat input = 840 BTU/lbm

Thermal efficiency is the ratio of work output to total heat input, expressed as a percentage:

Thermal efficiency = (Work output / Total heat input) × 100
Thermal efficiency = (540 BTU/lbm / 840 BTU/lbm) × 100
Thermal efficiency ≈ 64.29%

For more such questions on thermal efficiency, click on:

https://brainly.com/question/3276817

#SPJ11

The force that holds the spring stretched at a distance of 14 cm is 2 N. The potential energy stored in the spring is defined by the amount of work done on the spring when it is stretched.

the work done is 4 J. If the spring has been stretched to a distance of 14 cm beyond its natural length, the elongation (stretch) produced is given by; x = 14 cm = 0.14 m The work done to stretch the spring is given by. Work done = (1/2) kx²Since the work done is 4 J, we have;(1/2) kx² = 4J Here, k is the spring constant which we have not been given. We will use the formula below to solve for k;k = (2W)/x² = (2(4 J))/(0.14 m)² = 102.04 N/mThe force that holds the spring stretched at a distance of 14 cm is given by. F = k x = (102.04 N/m)(0.14 m) = 14.29 N ≈ 2 N (to 1 decimal place) To find the force (in Newtons) that holds the spring stretched at a distance of 14 cm, we can use the formula for work done: Work = Force × Distance. In this case, Work = 4 Joules, and Distance = 0.14 meters (converted from 14 cm). Rearranging the formula, we get Force = Work / Distance. Force = 4 Joules / 0.14 meters = 28.57 Newtons.

Learn more about Joules here:

https://brainly.com/question/18596314

#SPJ11

Approximate power  required for the glasses underwater to allow distant object visibility without a mask is -2.5 diopters.

A scuba diving mask is an important component of a scuba diving kit since it covers the eyes and nose while under the water. The mask has an air pocket inside that permits you to focus on objects underwater without experiencing a change in the size of the image or refraction.A snorkel mask is worn during snorkeling, whereas a scuba mask is worn during diving. Because of the difference in pressure between the atmosphere and the underwater environment, the mask must be manufactured in such a way that it can withstand the weight of the water. It is advisable to ensure that the mask is snug and that water does not seep in when it is worn.How much power must the glasses have underwater to allow distant object visibility without a mask?The approximate power that the glasses must have underwater to allow for distant object visibility without a mask is -2.5 diopters. A scuba diving mask aids in providing the right refraction and a focused view of objects underwater. The glasses, on the other hand, must compensate for the change in the focal length that occurs when light passes from one medium to another (in this case, water to air). The refractive index of the glasses compensates for the shift, allowing for clear and focussed visibility of distant objects. The -2.5 diopters power of the glasses is necessary to provide the best underwater sight.

Learn more about diving mask here:

https://brainly.com/question/30908085

#SPJ4

The left picture represents the solid in its normal, relaxed state. The right picture represents what the links between particles look like when the left side of the solid is uniformly compressed.

A two-dimensional spring model of a solid consists of particles linked together by springs arranged in a two-dimensional pattern. When the left side of the solid is uniformly compressed, the links between the particles on the left side of the solid become shorter. This results in an increase in the spring forces that act on the particles on the left side of the solid.

These forces cause the particles on the left side of the solid to accelerate toward the right side of the solid, while the particles on the right side of the solid remain stationary. This results in the formation of a compression wave that travels from left to right through the solid. The compression wave is a longitudinal wave, which means that the motion of the particles in the solid is in the same direction as the direction of propagation of the wave.

To learn more about Picture :

https://brainly.com/question/29211371

#SPJ11

Thus, the initial and final values of electrical energy  stored in the capacitors are 0.3125J and 0.3124J.

given,

the initial charge of the given capacitor is Qo = 5.00C

The capacitance  of the given capacitor is Co = 40.0F

therefore,

capacitors 10μF and 15μF are connected in a series format.

then equivalent capacitance is

[tex]\frac{1}{c}[/tex] = 1/10μf + 1/15μF

=> 3μF + 2μF/ 30μF

C = 6μF

therefore,

the equivalent capacitor is in parallel combination concerning capacitor 14μF.

Equivalent capacitance = C' = 14μF + 6μF

C' = 20μF × 10⁻⁶ F/1μF

C' = 20 × 10⁻⁶ F

then, the obtained equivalent capacitance is in parallel formation with the unlabeled capacitor.

C" = (20 ×10⁻⁶ F)² +40.0 F

C" = 40.0002 F

hence, the initial energy stored in the capacitor is

Ui = [tex]\frac{qo^{2} }{2Co}[/tex]

Ui = (5.00C)²/ 2× (40.0F)

Ui = 0.3125 J

the final energy in the capacitor is

Uf = [tex]\frac{q^{2} }{2C"}[/tex]

Uf = (5.00 C )²/ 2 × (40.00002 F)

Uf = 0.3124 J

Thus, the initial and final values of electrical energy  stored in the capacitors are 0.3125J and 0.3124J.

To learn more about Capacitors,

https://brainly.com/question/21851402

#SPJ4

The focal length of the lens is 15 cm. The correct option is C).

Using the thin lens equation

1/f = 1/d_o + 1/d_i

where f is the focal length of the lens, d_o is the object distance, and d_i is the image distance.

We are given that the object height, h_o, is 1.15 cm, the image height, h_i, is 5.75 cm, and the object distance, d_o, is 12 cm. Since the image is upright, the magnification, M, is positive:

M = h_i / h_o = 5.75 / 1.15 = 5

We can use the magnification equation to find the image distance

M = - d_i / d_o

d_i = - M * d_o = -5 * 12 cm = -60 cm

The negative sign indicates that the image is virtual, which means it is on the same side of the lens as the object.

Now we can use the thin lens equation to solve for the focal length:

1/f = 1/d_o + 1/d_i = 1/12 cm - 1/60 cm = 1/15 cm

f = 15 cm

Therefore, the focal length is 15 cm. The correct Answer is option C).

To know more about focal length:

https://brainly.com/question/29870264

#SPJ4

Answer:

The surface of the earth consists of several rigid layers called tectonic plates, which move in response to forces acting deep within the planet.

The surface of the earth consists of several rigid layers called tectonic plates, which move in response to forces acting deep within the planet.

What are tectonic plates?

Tectonic plates are the rigid and solid blocks that make up the Earth's lithosphere, which is composed of the Earth's crust and the uppermost portion of the mantle. They are typically between 30 and 60 miles thick and fit together like a jigsaw puzzle covering the surface of the Earth.The Earth's lithosphere is made up of tectonic plates that move. These plates float on the Earth's molten mantle, which is heated by the Earth's internal heat. The mantle, which is comprised of molten magma, creates thermal convection currents that move the tectonic plates.What causes the movement of tectonic plates?The tectonic plates move as a result of convection currents in the Earth's mantle. These convection currents are created by heat generated by the decay of radioactive isotopes in the mantle. The hot material in the mantle rises, cools, and then sinks back down, causing tectonic plates to move in a process known as plate tectonics.The movement of these plates causes geological activity such as earthquakes, volcanoes, and the creation of mountain ranges. Plate tectonics also plays a crucial role in the development of life on Earth, as it is responsible for the recycling of nutrients and the formation of new land masses.

To know more about tectonic plates click here:

brainly.com/question/19317822

#SPJ11

Answer:

To solve this problem, we need to use the conservation of energy principle. The potential energy of the block at the top of the incline is converted into kinetic energy as it slides down the incline. However, some of this energy is lost due to friction between the block and the incline. Let's start by calculating the potential energy of the block at the top of the incline:

where m is the mass of the block, g is the acceleration due to gravity, and h is the height of the incline.

Next, we can calculate the kinetic energy of the block at the bottom of the incline:

where m is the mass of the block and v is its velocity at the bottom of the incline.

The energy lost due to friction is simply the difference between the potential energy at the top and the kinetic energy at the bottom:

The cylinder would need to rotate at an angular speed of 1.44 x 10^-3 rad/s

To calculate the required angular speed of cylinder, we can use the following formula:

a_c = v^2 / r

where a_c is  centripetal acceleration, v is  linear speed, and r is the radius of the cylinder.

First, we can determine the free-fall acceleration on Earth, which is approximately 9.81 m/s^2.

20.0 miles = 32,186.88 meters, and 3.71 miles = 5,972.64 meters.

a = ω^2r,

Setting  centripetal acceleration equal to  free-fall acceleration, we have: [tex]9.81 m/s^2 = \omega^{2}(2,986.32 m)[/tex]

ω = [tex]1.44 * 10^{-3} rad/s[/tex]

Therefore, the cylinder would need to rotate at angular speed of 1.44 x 10^-3 rad/s to have the same centripetal acceleration at its surface as the free-fall acceleration on Earth.

To know more about centripetal acceleration, here

brainly.com/question/14465119

#SPJ4

8.To find the total resistance of the external circuit, we can add up the resistances of the three resistors in series: R = 20 + 30 + 50 = 100Ω.

9.To find the current drawn from the battery, we can use Ohm's Law: I = V / R = 5 / (0.7 + 100) = 0.048 A.

10.The terminal voltage of the battery can be found using the equation V = EMF - Ir, where r is the internal resistance of the battery. So, V = 5 - (0.048 * 0.7) = 4.966 V.

11.To measure the voltage across the 20Ω resistor, the voltmeter should be connected in parallel to the resistor. To measure the current through the resistor, the ammeter should be connected in series with the resistor.

If the circuit is not disconnected, the measurements would be accurate as the ammeter and voltmeter would be reading the values when the circuit is operational. The ammeter would read 0.048 A, which is the same as the current drawn from the battery, and the voltmeter would read 0.96 V, which is the voltage across the 20Ω resistor.

To know more about Ohm's Law, visit:

https://brainly.com/question/1247379

#SPJ1

we can't solve for the final velocity of the skier at the bottom of the slope.

When answering questions on Brainly, a question-answering bot should always be factually accurate, professional, and friendly. In addition, it should be concise and not provide extraneous amounts of detail.

Any typos or irrelevant parts of the question should be ignored. Below is the answer to the given question:If frictional forces do -11.0 kJ of work on her as she descends, how fast is she going at the bottom of the slope?The conservation of energy principle can be used to solve this problem.

As a skier descends a slope, her potential energy (PE) is converted to kinetic energy (KE) and work done by non-conservative forces such as friction.Conservative forces are forces that do not dissipate the mechanical energy of a system.

The conservation of energy principle states that the total mechanical energy of a system is constant when only conservative forces act on it. The total mechanical energy is the sum of kinetic and potential energies.Under the assumption that the potential energy at the top of the slope is zero,

the initial total mechanical energy is KE_0 = 1/2 mv_0^2where m is the skier's mass and v_0 is her initial velocity. The final mechanical energy is KE_f = 1/2 mv_f^2, where v_f is the skier's velocity at the bottom of the slope.

If the frictional force does work W_friction = -11.0 kJ, the change in mechanical energy isΔKE = KE_f - KE_0 = W_frictionThe work done by friction is negative because it dissipates mechanical energy.

Solving for the final velocity of the skier givesv_f = sqrt(2ΔKE/m + v_0^2) = sqrt(2W_friction/m + v_0^2)We have all the values except for m, the mass of the skier.

To learn more about :  velocity

https://brainly.com/question/80295

#SPJ11

The vertical curvature (radius of curvature) of the road is approximately 1370.6 meters. To solve this problem, we can follow these steps:

Step 1: Identify the given information

- Speed of the car (v) = 45 m/s

- Apparent weight increase = 15%

Step 2: Calculate the increase in gravitational force

Since the occupants' apparent weight is 15% higher,

the additional force acting on them can be calculated as 0.15 times the gravitational force (g), which is approximately 9.81 m/s^2.

- Additional force = 0.15 * 9.81 m/s² = 1.4715 m/s²

Step 3: Determine the centripetal acceleration
The additional force acting on the occupants is due to the centripetal acceleration (a_c) caused by the curvature of the road.

The centripetal acceleration can be calculated using the formula:

- a_c = v² / r, where r is the radius of curvature of the road.

Step 4: Calculate the radius of curvature

Rearrange the centripetal acceleration formula to find the radius of curvature

(r):- r = v² / a_c

Step 5: Substitute the values and calculate r

- r = (45 m/s)² / 1.4715 m/s²

- r ≈ 1370.6 meters

to know more about radius of curvature refer here:

https://brainly.com/question/30106465#

#SPJ11

Latent heat will be consumed during the cooling process, warming the surrounding air. A material turns from a liquid to a solid by releasing heat into the environment when it freezes.

The process of freezing requires the removal of latent heat from a substance to change its state from a liquid to a solid. This means that freezing consumes latent heat from the substance itself, causing it to cool down. However, since the process also requires the substance to release this heat to the surrounding environment, the environment air is warmed up instead of being cooled down. This warming effect is due to the fact that the heat energy released during the freezing process is transferred from the substance to the surrounding air. Therefore, although the substance being frozen may become colder, the surrounding air becomes warmer, and this can have significant effects on the environment, especially in areas where freezing occurs frequently or over extended periods of time.

Learn more about environmental air here:

https://brainly.com/question/30774791

#SPJ4

The square object's swinging motion can be represented by a simple pendulum. The object's center of mass lies at the intersection of its diagonals, and its moment of inertia may be computed as I = (1/12)ml2.

The frequency of the object's oscillation may be computed using the small angle approximation as f = (1/2) (mgl/I), where g is the acceleration due to gravity. The length of the pendulum is equal to the distance from the center of mass to the point of attachment, which may be computed as l/22. We get f = (1/2) (4g/l) by substituting the moment of inertia and the length into the frequency equation.  a result, the frequency of  oscillation of the square object is independent of its mass and is only determined by the length of its sides and the acceleration due to gravity. The frequency of oscillation is approximately 0.83 Hz for a square object with sides of length l.

learn more about  mass  here:

https://brainly.com/question/19694949

#SPJ4

The kinetic energy of the system after the mass is released and has moved to a point where the potential energy has decreased to 70 J is 85 J.

The total mechanical energy of the system (spring and mass) is conserved, and is equal to the sum of the potential energy and kinetic energy:

E = PE + KE

At the initial point, the potential energy of the system is 155 J, and the kinetic energy is zero:

Ei = PEi + KEi = 155 J + 0 J = 155 J

At the final point, the potential energy of the system is 70 J, and the kinetic energy is unknown:

Ef = PEf + KEf = 70 J + KEf

Since the total mechanical energy is conserved, we can equate Ei to Ef:

Ei = Ef

155 J = 70 J + KEf

KEf = 155 J - 70 J

KEf = 85 J

Therefore, the kinetic energy of the system after the mass is released and has moved to a point where the potential energy has decreased to 70 J is 85 J.

For such more question on kinetic energy:

https://brainly.com/question/8101588

#SPJ11

The kinetic energy of the roller coaster at the low point can be calculated using the conservation of energy principle.

The total energy at point A is equal to the sum of its kinetic and potential energies. At the low point, all the potential energy has been converted into kinetic energy. But, some energy has been lost due to friction, which is given as 60 kJ. Therefore, the kinetic energy at the low point can be calculated as follows: Initial energy at point A = Potential energy + Kinetic energy= 750 kJ + 165 kJ = 915 kJFinal energy at the low point = Kinetic energy = Potential energy at the low point= 0 kJUsing the conservation of energy principle, we have: Initial energy = Final energy + Energy lost in frictionOr915 kJ = Kinetic energy at the low point + 60 kJ Kinetic energy at the low point = 915 kJ - 60 kJ Kinetic energy at the low point = 855 kJTherefore, the kinetic energy of the roller coaster at the low point is 855 kJ.

Learn more about friction here:

https://brainly.com/question/13000653

#SPJ4

Using the principle of conservation of energy, we can calculate the force constant of a spring and the period of oscillation of a weight attached to the spring. However, to solve for the mass of the weight, we need more information about its oscillation.

When the weight W is suspended from the spring and reaches its equilibrium position, the potential energy stored in the spring is equal to the gravitational potential energy of the weight W:

[tex]1/2 k x^2[/tex]= m g h

where k is the force constant of the spring, x is the displacement of the spring from its equilibrium position (31.9 cm in this case), m is the mass of the weight W, g is the acceleration due to gravity, and h is the height of the weight W above the ground (which we can assume is zero).

We can solve for the force constant of the spring:

k = (2 m g h) / [tex]x^2[/tex]

Next, we can find the period of oscillation of the spring when the weight W is pulled down to a position 55.1 cm below its equilibrium position. The period of oscillation is given by:

T = 2π √(m / k)

where m is the mass of the weight W and k is the force constant of the spring that we just calculated.

Finally, we can use the period of oscillation to find the frequency of oscillation:

f = 1 / T

We now have expressions for the force constant of the spring, the period of oscillation, and the frequency of oscillation, all in terms of the mass of the weight W, which is unknown.

Learn more about conservation here:

https://brainly.com/question/9530080

#SPJ1

A device is defined as a unit of an electrical system, other than a conductor, that carries or transfers electric energy as its principal function.

 In electrical engineering, a device refers to a component or unit within an electrical system that performs a specific function.

Devices can be classified based on their function, behavior, or physical characteristics. This definition can be applied to a variety of devices commonly used in electrical systems such as transformers, generators, motors, switches, and more. These devices are designed to convert and transfer electrical energy in various ways to power different systems and devices.

For more such questions on conductor, click on:

https://brainly.com/question/492289

#SPJ11

The torque that the muscle produces on the wrist is 1.36575 Nm.

When the Palmaris longus muscle in the forearm is flexed, the wrist moves back and forth. If the muscle generates a force of 51.5 N and it is acting with an effective lever arm of 2.65 cm, the torque that the muscle produces on the wrist can be calculated as follows;

Step-by-step explanation:

The formula for torque is:

T = F × r

Where;

T is torque

F is force

R is the length of the lever arm

To calculate torque:

Torque (T) = Force (F) × length of lever arm (r)

So, substituting the given values, we have;

Torque (T) = 51.5 N × 0.0265 m = 1.36575 Nm

Therefore, the torque that the muscle produces on the wrist is 1.36575 Nm.

To know more about Torque, refer here:

https://brainly.com/question/28220969#

#SPJ11

If a warm air mass is located in the southwest united states and a cold air mass is located in the southeast united states, from west to east direction will the winds blow.

The prevailing westerlies blow from west to east, meaning that if a warm air mass is located in the southwest United States and a cold air mass is located in the southeast United States, the winds will blow eastward.

Therefore, from the east, the winds will blow. The winds will blow from the direction in which the pressure gradient force directs them.

The pressure gradient force is perpendicular to the isobars and directed from higher to lower pressure.

Wind is deflected to the right in the Northern Hemisphere and to the left in the Southern Hemisphere as a result of the Coriolis force, which is a consequence of the Earth's rotation.

The prevailing westerlies are winds that blow west to east between 30° and 60° latitude in both hemispheres.

For similar question on air mass

https://brainly.com/question/19626802

#SPJ11

The maximum kinetic energy for a frequency of light that has a stopping potential of 3 volts is 4.8 x 10^-19 joules.

The stopping potential of a photoelectric experiment is the minimum potential difference required to stop the emission of electrons from a metal surface when light is incident on it.

The maximum kinetic energy (KE) of an electron emitted by a light with a stopping potential (V) can be found using the formula:

KE = e * V

where e is the charge of an electron, which is approximately 1.6 x 10^-19 coulombs.

Given that the stopping potential is 3 volts, we can find the maximum kinetic energy as follows:

KE = (1.6 x 10^-19 C) * 3 V

KE = 4.8 x 10^-19 J

So, the maximum kinetic energy is 4.8 x 10^-19 joules.

For more such questions on kinetic energy, click on:

https://brainly.com/question/25959744

#SPJ11

The moment of inertia of a thin, uniform rod for an axis l/4 from one end and perpendicular to its length is (1/16) * m * l^2.

To find the snapshot of idleness of the slight, uniform pole for a hub found l/4 from one end and opposite to its length, we can utilize the equal pivot hypothesis. This hypothesis expresses that the snapshot of inactivity of an unbending body for any pivot lined up with a given hub through the focal point of mass is equivalent to the snapshot of latency for the given hub in addition to the result of the mass of the item and the square of the distance between the two tomahawks.

In the first place, we want to track down the snapshot of idleness of the pole for a pivot through its focal point of mass and opposite to its length. This can be determined involving the equation for the snapshot of idleness of a uniform bar around its focal point of mass, which is (1/12) * m * [tex]l^2[/tex].

Then, we really want to find the distance between the focal point of mass and the new pivot found l/4 from one end. Since the bar is of uniform thickness, the focal point of mass is situated at the midpoint of the bar, or l/2 from one or the flip side. Subsequently, the distance between the focal point of mass and the new hub is l/4.

At long last, we can utilize the equal pivot hypothesis to track down the snapshot of inactivity for the new hub. Utilizing the recipe I = I_cm + [tex]m*d^2[/tex], where I_cm is the snapshot of latency for the focal point of mass pivot, m is the mass of the bar, and d is the distance between the two tomahawks, we have:

[tex]I = (1/12) * m * l^2 + m * (l/4)^2= (1/12) * m * l^2 + (1/16) * m * l^2= (4/48 + 3/48) * m * l^2= (1/16) * m * l^2[/tex]

Hence, the snapshot of dormancy of the dainty, uniform pole for the pivot found l/4 from one end and opposite to its length is [tex](1/16) * m * l^2[/tex].

To learn more about moment of inertia, refer:

https://brainly.com/question/14284456

#SPJ4

The sum of these losses can typically result in the system's final output being around 85 to 88 percent of the sum of the rated power of the panels. Therefore, option C. 85 to 88 percent is the correct answer.

When calculating the overall efficiency or final output of a photovoltaic (PV) system without storage (batteries), the system's output will typically be around 85 to 88 percent of the sum of the rated power of the panels. This is due to various losses that occur in a PV system, including but not limited to:

Learn more about photovoltaic (PV) system

brainly.com/question/30632856

#SPJ4