Answer:
a) using
R=V/I =117/12.3
R=9.5 ohms
b)
E=V-I*R =117-3.38*9.5
E=84.8Volts
c)
at (1/3)rd of normal speed ,back emf is (1/3) of its maximum
value
E=(1/3)*84.8=28.3Volts
Current drawn
I=V-Eback/R =117-28.3/9.5
I=9.33A
Explanation:
The resistance is = 9.5 ohms
The back emf developed at normal speed is = 84.90 volts
The current drawn at one-third normal speed =9.33 A.
To calculate the resistance of the armature coil this formula is used;
V = IR
make R the subject of formula,
R = V/I
where R = resistance
V = voltage
I = Current
R = 117/12.3
R = 9.5 ohms
To calculate the back emf developed at normal speed, this formula is used;
E = V + Ir ( for normal emf)
But for back emf which is the difference between the supplied voltage and the loss from the current through the resistance, this formula is used;
E = V - Ir
where V = 117v
I = 3.38
r = 9.5
E = 117 - ( 3.38 × 9.5)
= 117 - 32.11
= 84.90 volts
To calculate the current drawn at one-third normal speed;
1/3 of Emf = 1/3 × 84.90
= 28.3volts
Therefore current (I) = V - E/ R
= 117- 28.3/9.5
= 88.7/9.5
= 9.33 A
Learn more about current here:
https://brainly.com/question/24858512
A solid 200-g block of lead and a solid 200-g block of copper are completely submerged in an aquarium filled with water. Each block is suspended just above the bottom of the aquarium by a thread. Which of the following is true?
A. More information is needed to choose the correct answer.
B. The buoyant force on the copper block is greater than the buoyant force on the lead block.
C. The buoyant force on the lead block is greater than the buoyant force on the copper block.
D. The buoyant force is the same on both blocks.
Answer:
B. The buoyant force on the copper block is greater than the buoyant force on the lead block.
Explanation:
Given;
mass of lead block, m₁ = 200 g = 0.2 kg
mass of copper block, m₂ = 200 g = 0.2 kg
density of water, ρ = 1 g/cm³
density of lead block, ρ₁ = 11.34 g/cm³
density of copper block, ρ₂ = 8.96 g/cm³
The buoyant force on each block is calculated as;
[tex]F_B = mg(\frac{density \ of \ fluid}{density \ of \ object} )[/tex]
The buoyant force of lead block;
[tex]F_{lead} = 0.2*9.8(\frac{1}{11.34} )\\\\F_{lead} = 0.173 \ N[/tex]
The buoyant force of copper block
[tex]F_{copper} = 0.2*9.8(\frac{1}{8.96})\\\\F_{copper} = 0.219 \ N[/tex]
Therefore, the buoyant force on the copper block is greater than the buoyant force on the lead block
House voltage is 240 volts. If a light bulb runs a current of 0.5 amps, what's the
resistance of the bulb?
Answer:
480 Ohms
Explanation:
Resistance: This can be defined as a opposition to current flow in an electric circuit. The S.I unit of resistance is ohms(Ω).
From the question,
V = IR................... Equation 1
Make R the subject of the equation
R = V/I............... Equation 2
V = The House voltage, I = Current, R = Resistance of the bulb.
Given: V = 240 Volts, I = 0.5 Amps.
Substitute into equation 2
R = 240/0.5
R = 480 Ohms
Hence the resistance of the bulb is 480 Ohms
A 4.0 kg mass is attached to a spring whose spring constant is 950 N/m. It oscillates with an amplitude of 0.12 m. What is the maximum velocity of the mass
Answer:
velocity = 2.62m/s
Explanation:
950= (4 x A)/0.12
950 x 0.12 = 4 x A
114 = 4 x A
A = 114/4
A = 28.5m/s²
U²=2asU² = 2 x 28.5 x 0.12U² = 6.84U = √6.84U = 2.62m/sThe maximum velocity of the mass is equal to 1.85,/s when the amplitude of oscillation is 0.12m.
What is the spring force?The spring force will be acting on the spring when the spring is stretched or compressed, which opposes the load force. These springs are divided into many types based on how this load force is applied to them.
F = -kx
where k is the spring constant and x is the displacement of the spring attached with mass.
Given, the mass attached to the spring, m = 4.0 Kg
The value of spring constant, k = 950 N/m
The amplitude of oscillation, A = 0.12m
The maximum velocity can be calculated as:
[tex]\frac{mv_{max}^2}{2} =\frac{kA^2}{2}[/tex]
[tex]v_{max} =\sqrt{\frac{kA^2}{m} }[/tex]
Substitute the values of the m, k, and A in the above equation:
Vmax = [tex]=\frac{950N/m(0.12m)^2}{4Kg}[/tex]
Vmax = √3.42 m/s
Vmax = 1.85m/s
Therefore, the maximum velocity of the mass is equal to 1/85 m/s.
Learn more about spring force, here:
https://brainly.com/question/14655680
#SPJ2
If an inductor, a capacitor, and a resistor are connected in series with a sine wave generator, what quantity will be common to all three components
Answer:
CURRENTExplanation:
For series connected elements (an inductor, a capacitor, and a resistor) in a simple AC circuit, the same current will flows through the elements since are are no presence of nodes between the elements. The total current from the source is what will flow through all of them.
For example, let assume the total current flowing in the circuit is 3A, the amount of current that will flow through the inductor, capacitor and resistor will be the same 3A because of the nature of their connection (series). It is the voltage across each of them that differs.
An individual is moving out of his apartment and has several boxes to carry down the stairs. Some of the boxes are light and some of the boxes are heavy. 3. Using the concept of motor units, describe how he generates more or less power to move the boxes.
Answer:
Motor unit is made up of motor neurons. Group of Motor Units work together to coordinate contraction of single muscle. When an individual needs to carry several boxes down stairs then his brain gives signal to neurons who innervates a group of skeletal muscle. When neurons receive signal they stimulate all muscle fibers in that particular motor unit.
Explanation:
Motor unit is made up of motor neurons. Group of Motor Units work together to coordinate contraction of single muscle. When an individual needs to carry several boxes down stairs then his brain gives signal to neurons who innervates a group of skeletal muscle. When neurons receive signal they stimulate all muscle fibers in that particular motor unit.
A solid, homogeneous sphere with a mass of m0, a radius of r0 and a density of ρ0 is placed in a container of water. Initially the sphere floats and the water level is marked on the side of the container. What happens to the water level, when the original sphere is replaced with a new sphere which has different physical parameters? Notation: r means the water level rises in the container, f means falls, s means stays the same.
A)
The new sphere has a density of ρ = ρ0 and a mass of m < m0.
B)
The new sphere has a density of ρ = ρ0 and a radius of r > r0.
C)
The new sphere has a density of ρ < ρ0 and a mass of m = m0.
The options are r, f, and s. Rises, Falls, Stays the same.
Answer:
(a) f
(b) r
(c) s
Explanation:
There are two forces on the sphere: weight and buoyancy.
Sum of forces in the y direction:
∑F = ma
B − mg = 0
B = mg
Buoyancy is equal to the weight of the displaced fluid, or ρVg, where ρ is the density of the fluid and V is the displaced volume.
ρVg = mg
ρV = m
V = m/ρ
(a) The mass decreases, so the displaced volume decreases.
(b) The sphere's density is constant and its radius increases, which means its mass increases, so the displaced volume increases.
(c) The mass stays the same, so the displaced volume is the same.
An electron moves to the left along the plane of the page, while a uniform magnetic field points into the page. What direction does the force act on the moving electron
Answer:
acting force is the answer
The direction of the magnetic force on the moving electron is upward.
The direction of the magnetic force on the electron can be determined by applying right hand rule.
This rule states that when the thumb is held perpendicular to the fingers, the thumb will point in the direction of the speed while the fingers will point in the direction of the field and the magnetic force will be perpendicular to the field.
Thus, we can conclude that, the direction of the magnetic force on the moving electron is upward.
Learn more here:https://brainly.com/question/14434299
A stunt driver rounds a banked, circular curve. The driver rounds the curve at a high, constant speed, such that the car is just on the verge of skidding to the outside of the curve. A front view of a car driving on a banked curve. The cross section of the banked road is constructed like a ramp. The car drives transversely to the slope of the ramp, so that the wheels of one side of the car are lower than the wheels on the other side of the car. Which forces are directly responsible for producing the car’s centripetal acceleration? Coriolis force centripetal force frictional force normal force gravitational force
Answer: C
Frictional force
Explanation:
The description of the question above is an example of a circular motion.
For a car travelling in a curved path, the frictional force between the tyres and the road surface will provide the centripetal force.
Since the road is banked, and the cross section of the banked road is constructed like a ramp. The car drives transversely to the slope of the ramp, so that the wheels of one side of the car are lower than the wheels on the other side of the car, for cornering the banked road, the car will not rely only on the frictional force.
Therefore, the correct answer is option C - the frictional force.
Two buses are moving in opposite directions with velocities of 36 km/hr and 108
km/hr. Find the distance between them after 20 minutes.
Explanation:
It is given that,
Speed of bus 1 is 36 km/h and speed of bus 2 is 108 km/h. We need to find the distance between bus 1 and 2 after 20 minutes.
Time = 20 minutes = [tex]\dfrac{20}{60}\ h=\dfrac{1}{3}\ h[/tex]
As the buses are moving in opposite direction, then the concept of relative velocity is used. So,
Distance, [tex]d=v\times t[/tex]
v is relative velocity, v = 108 + 36 = 144 km/h
So,
[tex]d=144\ km/h \times \dfrac{1}{3}\ h\\\\d=48\ km[/tex]
So, the distance between them is 48 km after 20 minutes.
The horizontal surface on which the objects slide is frictionless. If F = 6.0 N and M = 1.0 kg, what is the magnitude of the force exerted on the large block by the small block?
The image is missing, so i have attached it.
Answer:
The force exerted on the large block by the small block = 8.4 N
Explanation:
From the image attached, the mass of the small block = 2M while the mass of the large block = 3M
Also,Force on small block = F and force on large block = 2F
Equilibrium of forces on the left gives;
2F - N = 3Ma
Thus,
Ma = (2F - N)/3 - - - - eq1
Also, on right hand side, Equilibrium of forces gives;
N - F = 2Ma
Ma = (N - F)/2 - - - - eq2
Equating eq(1) and eq(2) gives us;
(2F - N)/3 = (N - F)/2
Where N is the force exerted on the large block by the small block.
Making N the subject gives;
4F - 2N = 3N - 3F
5N = 7F
N = 7F/5
We are given F = 6N
Thus;
N = 7(6)/5
N = 8.4 N
A particle might be placed:___________.
1. inside a uniform spherical shell of mass M, but not at the center
2. inside a uniform spherical shell of mass M, at the center
3. outside a uniform spherical shell of mass M, a distance r from the center
4. outside a uniform solid sphere of mass M, a distance 2r from the center
Rank these situations according to the magnitude of the gravitational force on the particle, least to greatest.
A) All tie
B) 1, 2, 3, 4
C) 1 and 2 tie, then 3 and 4 tie
D) 1 and 2 tie, then 3, then 4
E) 1 and 2 tie, then 4, then 3
Answer: D) 1 and 2 tie, then 3, then 4.
Explanation: Gravitational Force is one of the 4 fundamental forces of nature (the others being eletromagnetic, weak force and strong force) and is explained by Newton's Law of Universal Gravitation, in which, every massive particle attracts every other massive particle.
The way to calculate gravitational force is:
[tex]F_{G} = \frac{GMm}{r^{2}}[/tex]
G is Universal Gravitational Constant and it is constant anywhere in the universe.
M and m are mass of each object;
r is distance between the objects;
The formula shows that gravitational force acts at an inverse square law, i.e., if objects are 2 distances apart, Force between them will decrease to one quarter of it was.
So, analysing the question, a particle inside an uniform spherical shell not at the center and at the center will have equal forces.
Outside at a distance 2r, force will be less than at a distance r.
Then the order is 1=2 > 3 > 4
How much heat is needed to melt 2.5 KG of water at its melting point? Use Q= mass x latent heat of fusion.
Answer:
Q = 832 kJ
Explanation:
It is given that,
Mass of the water, m = 2.5 kg
The latent heat of fusion, L = 333 kJ/kg
We need to find the heat needed to melt water at its melting point. The formula of heat needed to melt is given by :
Q = mL
[tex]Q=2.5\ kg\times 333\ kJ/kg\\\\Q=832.5\ kJ[/tex]
or
Q = 832 kJ
So, the heat needed to melt the water is 832 kJ.
The temperature coefficient of resistivity for copper is 0.0068 (C°)-1. If a copper wire has a resistance of 104 Ω at 20°C, what is its resistance 80°C?
Answer:
R₈₀ = 146.43 Ω
Explanation:
The resistance of a resistor depends upon many factors. One of the main factors of the change in resistance of a resistor is the change in temperature. The formula for the resistance at a temperature other than 20°C is given as follows:
R₈₀ = R₀(1 + αΔT)
where,
R₈₀ = Resistance of wire at 80°C = ?
R₀ = Resistance of wire at 20° C = 104 Ω
α = Temperature coefficient of resistance for copper = 0.0068 °C⁻¹
ΔT = T₂ - T₁ = 80°C - 20°C = 60°C
Therefore,
R₈₀ = (104 Ω)[1 + (0.0068°C⁻¹)(60°C)]
R₈₀ = 146.43 Ω
An electron traveling with a speed v enters a uniform magnetic field directed perpendicular to its path. The electron travels for a time t0 along a half-circle of radius R before leaving the magnetic field traveling opposite the direction it initially entered the field. Which of the following quantities would change if the electron had entered the field with a speed 2v? (There may be more than one correct answer.)
A. The time the electron is in the magnetic field
B. The magnitude of the net force acting on the electron inside the field
C. The magnitude of the electron's acceleration inside the field
D. The radius of the circular path the electron travels
Answer:
C. The magnitude of the electron's acceleration inside the field
D. The radius of the circular path the electron travels
Explanation:
The radius of the electron's motion in a uniform magnetic field is given by
[tex]R = \frac{MV}{qB}[/tex]
where;
m is the mass of the electron
q is the charge of the electron
B is the magnitude of the magnetic field
V is speed of the electron
R is the radius of the electron's
Thus, the radius of the of the electron's motion will change since it depends on speed of the electron.
The magnitude of the electron's acceleration inside the field is given by;
[tex]a_c = \frac{V^2}{R}[/tex]
where;
[tex]a_c[/tex] is centripetal acceleration of electron
Thus, the magnitude of the electron's acceleration inside the field will change since it depends on the electron speed.
The time the electron is in the magnetic field is given by;
[tex]T = \frac{2\pi M}{qB}[/tex]
The time of electron motion will not change
The magnitude of the net force acting on the electron inside the field will not change;
[tex]qVB = \frac{MV^2}{R} \\\\qVB - \frac{MV^2}{R} = 0[/tex]
Therefore, the correct options are "C" and "D"
Imagine that while you and a passenger are in a deep-diving submersible in the North Pacific near Alaska’s Aleutian Islands, you encounter a long, narrow depression on the ocean floor. Your passenger asks whether you think it is a submarine canyon, a rift valley, or a deep-ocean trench. How would you respond? Explain your response.
Answer:
I would say its a deep ocean trench
Explanation:
This is because deep ocean trenches are found at the deepest part of the ocean and also at Pacific ocean margins or Rim where subduction usually occurs and Aleutian islands are part of the Pacific Rim
Consider 4 charges placed at the corners of a square with side 1.25m as shown. What are the magnitude and direction of the electrostatic force on Q1 resulring from other three charges?
(Note: Please put your final answer in 4 decimal places.). pls answer:)
Answer:
F = 2,8289 i ^ + 1,0909 j ^) 10⁻² N
F = 3.0226 10⁻² N , θ = 21.16º
Explanation:
For this exercise we use Coulomb's law
F = k q₁q₂ / r₁₂²
We also use that the force is a vector magnitude, so we must calculate each component of the force , see the adjoint for the direction of the vectors
X axis
Fₓ = -F₁₄ + F₁₃ₓ
Y axis
[tex]F_{y}[/tex] = F₁₂ -F_{13y}
let's look for the expression for each force
where the side of the square is a = 1.25 m
F₁₂ = k Q₁Q₂ / a²
F₁₄ = k Q₁Q₄ / a²
the distance between 1 and 3 is
d = √(a² + a²) = a √2
F₁₃ = k Q₁Q₃ / d²
let's use trigonometry to find the components
cos 45 = F₁₃ₓ / F₁₃
F₁₃ₓ = F₁₃ cos 45
F₁₃ₓ = k Q₁Q₃ / 2a²
sin 45 = F_{13y} / F₁₃
F_{13y} = F₁₃ sin 45
F_{13y} = k Q₁Q₃ / 2a² sin 45
Taking all terms, we substitute in the force for each axis
X axis
Fₓ = - k Q₁Q₄ / a² + k Q₁Q₃ / 2a₂ cos 45
Fₓ = k Q₁ / a² ( -Q₄ + Q₃ /2 cos 45)
Fₓ = 9 10⁹ 1.5 10⁻⁶ / 1.25² (- 4.5 10⁻⁶ + 3.5/2 cos 45 10⁻⁶)
Fₓ = 8.64 10³ (3.2626 10⁻⁶)
Fₓ = 2.8189 10⁻² N
Y axis
F_{y} = k Q₁Q₂ / a² - k Q₁Q₃ /2a² sin 45
F_{y} = k Q₁ / a² (Q₂ - Q₃ /2 sin45)
F_{y} = 9 10⁹ 1.5 10⁻⁶/ 1.25² (2.5 10⁻⁶ - 3.5/2 sin 45 10⁻⁶)
F_{y} = 8.64 10³ (1.26256 10⁻⁶)
F_{y} = 1.0909 10⁻² N
The result can be given in two ways
1) F = Fₓ i ^ + F_{y} j ^
F = 2,8289 i ^ + 1,0909 j ^) 10⁻² N
2) in the form of a module and an angle, for which we use the Pythagorean theorem and trigonometry
F = √ (Fₓ² + F_{y}²)
F = 10⁻² √ (2,8189² + 1,0909²)
F = 3.0226 10⁻² N
tan θ = F_{y} / Fx
θ = tan⁻¹ (F_{y} / Fₓ)
θ = tan⁻¹ (1.0909 / 2.8189)
θ = 21.16º
A room with 3.1-m-high ceilings has a metal plate on the floor with V = 0V and a separate metal plate on the ceiling. A 1.1g glass ball charged to 4.7 nC is shot straight up at 4.8 m/s from the floor level. How high does the ball go if the ceiling voltage is +3.0x10^6V?
Answer:
The ball traveled 0.827 m
Explanation:
Given;
distance between the metal plates of the room, d = 3.1 m
mass of the glass, m = 1.1g
charge on the glass, q = 4.7 nC
speed of the glass ball, v = 4.8 m/s
voltage of the ceiling, V = +3.0 x 10⁶ V
The repulsive force experienced by the ball when shot to the ceiling with positive voltage, can be calculated using Coulomb's law;
F = qV/d
|F| = (4.7 x 10⁻⁹ x 3 x 10⁶) / (3.1)
|F| = 4.548 x 10⁻³ N
F = - 4.548 x 10⁻³ N
The net horizontal force experienced by this ball is;
[tex]F_{net} = F_c - mg\\\\F_{net} = -4.548 *10^{-3} - (1.1*10^{-3} * 9.8)\\\\F_{net} = -15.328*10^{-3} \ N[/tex]
The work done between the ends of the plate is equal to product of the magnitude of net force on the ball and the distance traveled by the ball.
[tex]W = F_{net} *h\\\\W = 15.328 *10^{-3} * h[/tex]
W = K.E
[tex]15.328*10^{-3} *h = \frac{1}{2}mv^2\\\\ 15.328*10^{-3} *h = \frac{1}{2}(1.1*10^{-3})(4.8)^2\\\\ 15.328*10^{-3} *h =0.0127\\\\h = \frac{0.0127}{15.328*10^{-3}}\\\\ h = 0.827 \ m[/tex]
Therefore, the ball traveled 0.827 m
The height at which the ball goes for the given parameters is; 0.827 m
What is the height of the ball?We are given;
distance between the metal plates; d = 3.1 m
mass of glass; m = 1.1g = 0.0011 kg
charge on the glass; q = 4.7 nC = 4.7 × 10⁻⁹ C
speed of the glass ball; v = 4.8 m/s
voltage of the ceiling; V = +3.0 × 10⁶ V
The repulsive force experienced by the ball is gotten from the formula;
F = qV/d
|F| = (4.7 × 10⁻⁹ × 3 × 10⁶)/3.1
|F| = 4.548 × 10⁻³ N
F = -4.548 × 10⁻³ N (negative because it is repulsive force)
The net horizontal force experienced by the ball is;
F_net = F - mg
F_net = (-4.548 × 10⁻³) - (0.0011 × 9.8)
F_net = -15.328 × 10⁻³ N
To get the height of the ball, we will use the formula;
F_net * h = ¹/₂mv²
h = (¹/₂ * 0.0011 * 4.8²)/(15.328 × 10⁻³)
We took the absolute value of F_net, hence it is not negative
h = 0.827 m
Read more about height of ball at; https://brainly.com/question/12446886
Three resistors, 6.0-W, 9.0-W, 15-W, are connected in parallel in a circuit. What is the equivalent resistance of this combination of resistors?
Answer:
2.9Ω
Explanation:
Resistors are said to be in parallel when they are arranged side by side such that their corresponding ends are joined together at two common junctions. The combined resistance in such arrangement of resistors is given by;
1/Req= 1/R1 + 1/R2 + 1/R3 .........+ 1/Rn
Where;
Req refers to the equivalent resistance and R1, R2, R3 .......Rn refers to resistance of individual resistors connected in parallel.
Note that;
R1= 6.0Ω
R2 = 9.0Ω
R3= 15.0 Ω
Therefore;
1/Req = 1/6 + 1/9 + 1/15
1/Req= 0.167 + 0.11 + 0.067
1/Req= 0.344
Req= (0.344)^-1
Req= 2.9Ω
The equivalent resistance of this combination of resistors is 2.9Ω.
Calculation of the equivalent resistance:The combined resistance in such arrangement of resistors is provided by;
1/Req= 1/R1 + 1/R2 + 1/R3 .........+ 1/Rn
here.
Req means the equivalent resistance and R1, R2, R3
.Rn means the resistance of individual resistors interlinked in parallel.
Also,
R1= 6.0Ω
R2 = 9.0Ω
R3= 15.0 Ω
So,
1/Req = 1/6 + 1/9 + 1/15
1/Req= 0.167 + 0.11 + 0.067
1/Req= 0.344
Req= (0.344)^-1
Req= 2.9Ω
learn more about resistance here: https://brainly.com/question/15047345
An object with a mass of 5.5 kg is allowed to slide from rest down an inclined plane. The plane makes an angle of 30o with the horizontal and is 72 m long. The coefficient of friction between the plane and the object is 0.35. The speed of the object at the bottom of the plane is:_________.
a. 24 m/s.
b. 11 m/s.
c. 15 m/s.
d. 5.3 m/s.
e. 17 m/s.
Answer:
The speed will be "16.67 m/s".
Explanation:
The given values are:
Distance
= 72 m
Angle
= 30°
Acceleration
= [tex]g(sin \theta-ucos \theta)[/tex]
= [tex](9.8\times sin30^{\circ}) - (0.53\times cos30^{\circ})[/tex]
= [tex]1.929 \ m/s^2[/tex]
Let the speed be "v".
⇒ [tex]v^2=u^2+2as[/tex]
⇒ [tex]v^2=0(2\times 1.929\times 72)[/tex]
⇒ [tex]v^2=277.226[/tex]
⇒ [tex]v=\sqrt{277.776}[/tex]
⇒ [tex]v=16.67 \ m/s[/tex]
You are moving at a speed 2/3 c toward Randy when shines a light toward you. At what speed do you see the light approaching you
Answer:
The speed of light will be c=3x10^8m/s
Explanation:
This is the same as the speed of light because your speed does not affecttje speed of light so you will see the light approaching you at the same speed of light c
Given that the mass of the Earth is 5.972 * 10^24 kg and the radius of the Earth is
6.371 * 10^6 m and the gravitational acceleration at the surface of the Earth is 9.81
m/s^2 what is the gravitational acceleration at the surface of an alien planet with
2.4 times the mass of the Earth and 1.9 times the radius of the Earth?
Although you do not necessarily need it the universal gravitational constant is G =
6.674 * 10^(-11) N*m^2/kg^2
9
Answer:
gₓ = 6.52 m/s²
Explanation:
The value of acceleration due to gravity on the surface of earth is given as:
g = GM/R² -------------------- equation 1
where,
g = acceleration due to gravity on surface of earth
G = Universal Gravitational Constant
M = Mass of Earth
R = Radius of Earth
Now, for the alien planet:
gₓ = GMₓ/Rₓ²
where,
gₓ = acceleration due to gravity at the surface of alien planet
Mₓ = Mass of Alien Planet = 2.4 M
Rₓ = Radius of Alien Planet = 1.9 R
Therefore,
gₓ = G(2.4 M)/(1.9 R)²
gₓ = 0.66 GM/R²
using equation 1
gₓ = 0.66 g
gₓ = (0.66)(9.81 m/s²)
gₓ = 6.52 m/s²
How many electrons circulate each second through the cross section of a conductor, which has a current intensity of 4A.
Answer:
2.5×10¹⁹
Explanation:
4 C/s × (1 electron / 1.60×10⁻¹⁹ C) = 2.5×10¹⁹ electrons/second
What would be the correct value of m in the interference equation if the growth process were started again and the diamond layer were grown to three times the thickness t
Answer:
To calculate the correct value of m if the thickness t is grown 3 times again we can deduce that:
2*(3u)*t = m* lambda
Making m the subject of the formula will give the formula:
m= 6*u*t/ Lambda
Given: Lambda= 633*10^9 while u and t are unknown
Therefore the value of m can be calculated given the formula below:
m= 6*u*t/ 633*10^9
Explanation:
To calculate the correct value of m if the thickness t is grown 3 times again we can deduce that:
2*(3u)*t = m* lambda
Making m the subject of the formula will give the formula:
m= 6*u*t/ Lambda
Given: Lambda= 633*10^9 while u and t are unknown
Therefore the value of m can be calculated given the formula below:
m= 6*u*t/ 633*10^9
A 0.500-V potential difference is maintained across a 1.50-m length of tungsten wire that has a cross-sectional area of 0.800 mm2. What is the current in the wire
Answer:
5.95 A
Explanation:
From the question
R = ρL/A..................... Equation 1
Where R = resistance of the tungsten wire, ρ = Resistivity of the tungsten wire, L = length, A = cross sectional area.
Given: L = 1.5 m, A = 0.8 mm² = 0.8×10⁻⁶ m, ρ = 5.60×10⁻⁸ Ω.m
Substitute these values into equation 1
R = 1.5(5.60×10⁻⁸)/0.8×10⁻⁶
R = 0.084 Ω.
Finally, using Ohm law,
V = IR
Where V = Voltage, I = current
Make I the subject of the equation
I = V/R............... Equation 2
I = 0.5/0.084
I = 5.95 A
Suppose your 50.0 mm-focal length camera lens is 51.0 mm away from the film in the camera. (a) How far away is an object that is in focus
Answer:
2.55m
Explanation:
Using 1/do+1/di= 1/f
di= (1/f-1/do)^-1
( 1/0.0500-1/0.0510)^-1
= 2.55m
You connect three resistors with resistances R, 2R, and 3R in parallel. The equivalent resistance of the three resistors will have a value that is
Answer:
The equivalent is 6R/11Explanation:
We know that the equivalent resistance of resistors connected in parallel is expressed as
[tex]\frac{1}{Re} =\frac{1}{R1} +\frac{1}{R2}+\frac{1}{R3}\\\\\frac{1}{Re} =\frac{1}{R} +\frac{1}{2R}+\frac{1}{3R}\\[/tex]
the L.C.M is 6R
[tex]\frac{1}{Re} =\frac{6+3+2}{6R} = \frac{11}{6R} \\\\Re= \frac{6R}{11}[/tex]
Let’s measure precisely how much electromotive force the generator can produce. The amount of electromotive force is measured in volts. In fact, electromotive force is sometimes referred to as voltage. Use a digital multimeter to measure the voltage of your generator. Connect the free ends of the probe wires to the wires coming out of the generator. What is the voltage reading when the generator is idle (i.e. when the crank is not being turned?)
Answer:
fem = 0
Explanation:
The electromotive force is given by Faraday's law
fem = - d [tex]\phi _{B}[/tex] / dt
where \phi _{B} is the flux of the magnetic field
The low magnetic flux is
\phi _{B} = B. A = B A cos θ
substituting
fem - d (B A cos θ) / dt
therefore for an electromotive force to exist there must be a change with respect to the time of
* The magnetic field
* The area waxed by the loop
* the angle between the magnetic field and the normal loop
* Any combination of the above
In this case, as the generator is stopped (inactive), there is no change in the parameters, therefore the electromotive force is zero (fem = 0).
Dr. Stein's hypothesis is that excess sugar causes hyperactivity. He is interested in doing research.
Which research method would be the best to use?
Answer:
The correct answer would be - dependent independent variable experiment.
Explanation:
Dr. Stein hypothesized that excess sugar causes hyperactivity, so sugar treatment /no sugar treatment would be independent variable. By giving some children sugar and others a sugar cookies he can manipulate the independent variable.
Similarly , the dependent variable is the result or outcome of independent variable, or what Dr. Stein hypothesize to be the result of excess sugar . In this sugar experiment, then, the dependent variable is the children's hyper activity level.
Thus, the correct answer would be - dependent independent variable experiment.
The best research method to use for the research of hyperactivity, would be dependent-independent variable experiment.
The given problem is based on the effect of sugar on hyperactivity. Hyper activity refers to the increased movement, impulse actions and a shorter attention span.
Dr. Stein hypothesized that excess sugar causes hyperactivity, so sugar treatment /no sugar treatment would be independent variable. By giving some children sugar and others a sugar cookies he can manipulate the independent variable.Similarly , the dependent variable is the result or outcome of independent variable, or what Dr. Stein hypothesize to be the result of excess sugar . In this sugar experiment, then, the dependent variable is the children's hyper activity level.
Thus, we can conclude that the best research method to use, would be - dependent-independent variable experiment.
Learn more about the hyperactivity here:
https://brainly.com/question/15539672
car travel at the speed of 20 km/hr for 2 hour and 60 km/hr for next 2 hour find average speed
A system is a group of objects that’s analyzed as one unit. Consider a car moving along a road that has a flat section and a hill. The energy of the car at any given time is equal to the energy that its engine provides minus the energy that the car. When the car moves along the flat section, all of its energy is , which is calculated from its velocity and . When the car moves uphill, some of its energy is transformed to , which is calculated from its gravity, height, and .
Answer:
a) Em= K +U, b) Em= K
Explanation:
The system in this case is formed by the mobilizes and the hill.
Let's write the expressions correctly and completely.
a) When the car moves in the path, the mechanical energy is the siua of the kinetic energy of the car and the potential energy of the car when going up the hill.
Em = K + U
be) when the car moves in the flat part all the mechanical energy is formed by its kinetic energy that is calculated with the mass and speed of the car
Em = K
c) When the car goes up the hill the energy the mechanical energy is conserved, but part of the kinetic energy is transformed into potential energy.
Answer:
leaves
kinetic energy
mass
potential energy
mass
Explanation: