a mixture of oxygen and nitrogen gases, at a total pressure of 783 mm hg, contains 3.50 grams of oxygen and 3.48 grams of nitrogen. what is the partial pressure of each gas in the mixture?

Since the filtrate has passed through the filter paper, any undissolved solute particles have been removed, and the filtrate is a clear solution. This means the filtrate is likely to be a saturated solution, as the maximum amount of solute has been dissolved in the solvent.

Based on your question, we have a beaker from trial 8 in model 2, and its contents have been vigorously stirred and then poured into filter paper in a funnel. To determine whether the filtrate is unsaturated or saturated, let's consider the steps involved in this process.
Step 1: Vigorously stir the contents of the beaker
Stirring helps in dissolving more solute into the solvent, potentially creating a saturated solution if the maximum amount of solute is dissolved.
Step 2: Pouring the contents into filter paper in a funnel
This step helps separate any undissolved solute particles from the solution, allowing only the liquid (solution) to pass through the filter paper.
Step 3: Collecting the filtrate
The liquid that drips from the filter paper is called the filtrate, which is a clear solution without any undissolved solute particles.
However, it is essential to know the specific conditions of trial 8 in model 2 to give a definite answer.

For more such questions on filtrate

brainly.com/question/26104477

#SPJ11

c. Hydrocarbons make up the majority of petroleum, but it also includes hydrocarbon derivatives that contain oxygen, nitrogen, and Sulphur. Between four and twenty carbon atoms per hydrocarbon make up the hydrocarbons in petroleum.

These substances combine to generate a wide range of intricate molecular structures, some of which are difficult to distinguish. Almost all crude oil, notwithstanding variances, contains between 12 and 15 percent hydrogen and 82 and 87 percent carbon by weight. The main components of petroleum and natural gas are hydrocarbons. They are used as lubricants, fuels, and raw materials for making industrial chemicals, polymers, fibers, rubber, solvents, and explosives.

Learn more about Hydrocarbons here:

https://brainly.com/question/11344764

#SPJ4

Complete question:

petroleum is a gooey liquid consisting primarily of group of answer choices.

A. oxygen

B. silicon

C. hydrocarbon compounds

D.  sulfur

In a titration, 14.128 ml of a 1.972 m weak base solution is placed in a 125 ml Erlenmeyer flask. the pH of the solution is 4.60.

To find the pH of the solution, we need to calculate the concentration of the weak base after it has reacted with the strong acid.

First, let's calculate the number of moles of HClO4 that were added to the flask:

1.972 M x (1.972 mL - 0.00 mL) = 3.893264 mmol HClO4

Since the weak base and strong acid react in a 1:1 mole ratio, we know that 3.893264 mmol of the weak base was also present in the flask.

The volume of the solution in the flask is 14.128 mL or 0.014128 L. Therefore, the concentration of the weak base in the flask before the titration was:

1.972 M x (14.128 mL / 1000 mL) = 0.027925136 M

Now we can use the concentration of the weak base and the amount of moles of weak base to calculate the concentration of the weak base after the titration:

0.027925136 M - (3.893264 mmol / 0.125 L) = 0.001543M

The pH of the solution can be calculated using the pKa of the weak base:

pH = pKa + log([A-]/[HA])

We'll need to know the pKa of the weak base to solve the problem. Let's assume the weak base is ammonia (NH3), which has a pKa of 9.24.

Substituting the values we have:

pH = 9.24 + log([NH2-]/[NH3])

We need to find the ratio of [NH2-] (conjugate base) to [NH3] (weak base).

Since we started with 0.027925136 M of NH3, and the weak base and strong acid react in a 1:1 mole ratio, we know that 3.893264 mmol of NH3 reacted, leaving 0.024031872 mol of NH3 in the solution.

Since NH3 is a weak base that undergoes partial dissociation in water, we can assume that [NH2-] = [H+] and [NH3] = [OH-].

Therefore, [H+] = [NH2-] = x

[OH-] = [NH3] = Kw/x = 1.0 x 10^-14 / x

Substituting these values into the equation above:

pH = 9.24 + log(x / 0.024031872)

To solve for x, we'll need to use the quadratic formula because the dissociation of NH3 is not complete, making it a weak acid/base problem.

x^2 + 1.77x - 1.55 x 10^-13 = 0

Solving this equation yields:

x = 1.21 x 10^-7 M

Therefore, the pH of the solution is:

pH = 9.24 + log(1.21 x 10^-7 / 0.024031872) = 4.60

Therefore, the pH of the solution is 4.60.

Know more about titration here: https://brainly.com/question/31229711

#SPJ4

Calculate the maximum concentration of the compound: Use the stoichiometry from the balanced chemical equation to determine the maximum concentration of the compound that can be present without precipitating.

To calculate the maximum concentration that can be present without precipitating, follow these steps:

1. Identify the solubility product constant (Ksp): First, look up the Ksp value for the specific compound in question. This value represents the equilibrium constant for the dissolving process of the solid into its constituent ions.

2. Write the balanced chemical equation: Write the balanced chemical equation for the dissolution of the solid into its ions, including the coefficients for each ion.

3. Write the expression for the solubility product (Ksp): Write the expression for Ksp using the concentration of the ions and their respective coefficients from the balanced chemical equation.

4. Solve for the maximum concentration of the ions: Rearrange the Ksp expression to solve for the maximum concentration of the ions that can be present without precipitating. This may require some algebraic manipulation, depending on the complexity of the expression.

5. Calculate the maximum concentration of the compound: Use the stoichiometry from the balanced chemical equation to determine the maximum concentration of the compound that can be present without precipitating.

By following these steps, you can calculate the maximum concentration that can be present without precipitating for a specific compound.

To know more about "Concentration" refer here:

https://brainly.com/question/6324861#

#SPJ11

The reaction between HCl and NaOH produces a neutral solution, so the resulting pH is 7, as there are no excess H+ or OH- ions.

To work out the pH of the arrangement acquired by blending 55.00 mL of 0.0954 M HCl and 47.00 mL of 0.1095 M NaOH, we first need to decide how much corrosive and base that respond. The reasonable condition for the response is:

HCl + NaOH → NaCl + H2O

The stoichiometry of the response shows that one mole of HCl responds with one mole of NaOH to frame one mole of NaCl and one mole of water. Thusly, the quantity of moles of HCl and NaOH can be determined as follows:

moles of HCl = 0.05500 L x 0.0954 mol/L = 0.00525 mol

moles of NaOH = 0.04700 L x 0.1095 mol/L = 0.00514 mol

Since the response is between serious areas of strength for an and a solid base, the subsequent arrangement will be nonpartisan. This is on the grounds that the solid corrosive and base will totally respond to shape a salt and water, leaving no overabundance H+ or Goodness particles in the arrangement. Accordingly, the pH of the subsequent arrangement will be 7.

To learn more about ph of the solution, refer:

https://brainly.com/question/15968113

#SPJ4

The statements which best describes the synergistic interaction effect is option b. An interaction between two or more medicines that increases their effectiveness.

A synergistic interaction effect is when two or more medicines taken together have a greater effect than the sum of their individual effects. This can lead to an increased effectiveness of the treatment.

Synergistic interaction effect is a phenomenon that occurs when two or more drugs or substances interact in a way that their combined effect is greater than the sum of their individual effects.

In other words, when two or more drugs or substances are used together, they can produce a more powerful and effective response than when used separately.

For more question on synergistic interaction effect click on

https://brainly.com/question/10564761

#SPJ11

The pH of the buffer solution is approximately 4.79.

To calculate the pH of the buffer solution, we need to use the Henderson-Hasselbalch equation, which relates the pH of the buffer to the pKa of the weak acid and the ratio of its conjugate base and weak acid forms in the solution. The equation is, pH = pKa + log([A⁻]/[HA])

where pKa is the dissociation constant of the weak acid, [A⁻] is the concentration of the conjugate base (acetate ion, CH₃COO⁻), and [HA] is the concentration of the weak acid (acetic acid, CH₃COOH).

First, we need to calculate the pKa of acetic acid. The pKa value for acetic acid is 4.76 at 25°C. Next, we need to find the concentrations of CH₃COOH and CH₃COO⁻ in the buffer solution. We know that we have 87.5 g of CH₃COONa, which is the sodium salt of acetic acid, in 1.00 L of 1.00 M CH₃COOH. To find the concentration of CH₃COOH, we can use the following formula,

moles of CH3COOH = M × V = 1.00 M × 1.00 L = 1.00 moles

The molar mass of CH₃COOH is 60.05 g/mol, so the mass of 1.00 moles is,

mass of CH₃COOH = 1.00 moles × 60.05 g/mol = 60.05 g

The amount of CH₃COOH that reacts with the Na+ in CH₃COONa is negligible, so the concentration of CH₃COOH remains 1.00 M.

To find the concentration of CH₃COO⁻, we need to use stoichiometry. The chemical equation for the dissociation of CH₃COOH in water is,

CH₃COOH + H₂O ⇌ CH₃COO⁻ + H₃O⁺

The acid dissociation constant (Ka) for this reaction is, Ka = [CH₃COO⁻][H₃O⁺]/[CH₃COOH]

At equilibrium, the concentrations of CH3COOH and H₃O⁺ are equal and can be represented as [H3O+]. The concentration of CH₃COO⁻ is equal to the amount of CH₃COOH that has dissociated,

[CH₃COO⁻] = moles of CH₃COOH dissociated/L of solution = moles of NaCH₃COO/L of solution

The number of moles of CH₃COONa in 87.5 g is,

moles of CH₃COONa = 87.5 g / 82.03 g/mol = 1.066 moles

Since each mole of CH₃COONa dissociates into one mole of CH₃COO⁻, the concentration of CH₃COO⁻ in the buffer solution is,

[CH₃COO⁻] = 1.066 moles / 1.00 L = 1.066 M

Now we can use the Henderson-Hasselbalch equation to calculate the pH of the buffer solution,

pH = pKa + log([A⁻]/[HA])

pH = 4.76 + log(1.066/1.00)

pH = 4.76 + 0.03

pH = 4.79

To know more about buffer solution, here

brainly.com/question/28642244

#SPJ4

When a moderate amount of a weak acid is placed in aqueous solution  the HA which is a nonionized acid considered as the greatest concentration. Option (A) is correct.

A weak acid is defied as an acid which is partially dissociates into its ions in an aqueous solution or in the water. It is evident that the conjugate base of a weak acid is a weak base while the conjugate acid of a weak base is considered as a weak acid. When a weak acid is placed in aqueous solution a non ionized form is in greatest concentration as the weak acid dissociates smaller amount. These are the acids which don't completely dissociate in the solution. A weak acid generally not considered as the strong acid as it is not dissociates completely.

The chemical reaction can be written as,

HA (aq.)  + [tex]H_{2} O[/tex] (l)   ------------>  [tex]A^{-}[/tex] (aq.)  +  [tex]H_{3}O ^{+}[/tex] (aq.)

In this chemical reaction,  HA is considered as the greatest concentration.

To learn more about Weak acid

https://brainly.com/question/24018697

#SPJ4

The complete question is,

when a moderate amount of a weak acid is placed in aqueous solution, which of the following will be present in the greatest concentration?

select the correct answer below:

A. the nonionized acid

B. the hydronium ion

C. the conjugate base of the acid

D.  impossible to predict

A substance that contains a hydrogen atom and can be given as a hydrogen ion in an aqueous solution is considered an acid, according to the Arrhenius hypothesis. Arrhenius acids are the name given to such compounds.

According to Arrhenius: Acid: Acids are those substances that, when dissolved in water, produce H+ ions. Base: Bases are compounds that, when dissolved in water, give off OH ions.

According to the Bronsted-Lowry definition, an acid is a substance that contributes protons to the formation of a bond or takes a pair of valence electrons. (in the Lewis definition).

To know more about aqueous solution visit:-

https://brainly.com/question/26856926

#SPJ1

Question:

Which term describes an acid according to the Arrhenius acid-base theory?

Answer:

120 mm Hg

Explanation:

120 mm Hg

.4 x 300

In the given statement, if 40% of the air on board the space shuttle is composed of O2, and the cabin is pressurized to 300 mmHg, then the partial pressure of oxygen would be: 120 mmHg.

Partial pressure is the pressure of each component of a mixture of gases. Dalton's law of partial pressures states that the total pressure of a mixture of gases is the sum of the partial pressures of each gas present. This means that the total pressure of a mixture is the sum of the partial pressure of each gas in the mixture.Given that 40% of the air on board the space shuttle is composed of O2, then the partial pressure of O2 can be calculated as follows:Partial pressure of O2 = Total pressure x Fraction of O2 in the mixture Partial pressure of O2 = 300 mmHg x 0.4Partial pressure of O2 = 120 mmHg. Therefore, the partial pressure of oxygen in the cabin of the space shuttle would be 120 mmHg.

To know more about oxygen click here:

brainly.com/question/9148379

#SPJ11

In an IR spectrum of CO2 and H20, a double-beam spectrophotometer with a reference cell can be used to subtract out the interference from the background, solvent or instrument noise and helps to improve the accuracy and precision of IR spectroscopy measurements by eliminating interferences that can affect the quality of data.

Some examples of interferences that can be subtracted by using a double-beam spectrophotometer with a reference cell:

Learn more about Double-beam spectrophotometers, here:

https://brainly.com/question/21578855

#SPJ4

We can reduce the risks and difficulties brought on by using less nonrenewable resources by adopting a comprehensive strategy for doing so.

Environmental Damage: Extraction, transportation, and burning of nonrenewable resources such as coal, oil, and gas can cause environmental damage such as air and water pollution, soil degradation, and climate change.

Price Volatility: The prices of nonrenewable resources can fluctuate greatly, making it difficult for businesses and consumers to plan and budget.

Energy Security: Dependence on nonrenewable resources can create energy security risks, as supplies can be disrupted due to geopolitical tensions or natural disasters.

Depletion: Nonrenewable resources are finite and can eventually be depleted, which can lead to economic and social challenges.

To limit our dependence on nonrenewable resources, we can take several steps, including:

Increasing Energy Efficiency: We can reduce our reliance on nonrenewable resources by improving energy efficiency in buildings, vehicles, and industry.

Developing Renewable Energy Sources: We can invest in renewable energy sources such as solar, wind, and hydro power to replace nonrenewable resources.

Encouraging Sustainable Practices: Governments can encourage sustainable practices such as recycling, reducing waste, and conserving resources.

Promoting Research and Development: We can invest in research and development of new technologies and solutions that reduce our dependence on nonrenewable resources and address associated problems.

Learn more about nonrenewable here:

https://brainly.com/question/14813979

#SPJ1

In the citrate cycle, also known as the Krebs cycle or TCA cycle, the production of NADH occurs in several steps. The reaction that produces NADH from the given options is not the oxidation of succinate by succinate dehydrogenase to form fumarate. This particular reaction generates FADH2 instead of NADH.

However, there are other reactions within the citrate cycle that do produce NADH. These include:

1. Isocitrate dehydrogenase: This enzyme catalyzes the conversion of isocitrate to alpha-ketoglutarate, which results in the production of NADH.

2. Alpha-ketoglutarate dehydrogenase complex: This enzyme complex converts alpha-ketoglutarate to succinyl-CoA, generating another molecule of NADH.

3. Malate dehydrogenase: This enzyme catalyzes the conversion of malate to oxaloacetate, producing NADH in the process.

In summary, the oxidation of succinate by succinate dehydrogenase to form fumarate does not produce NADH. Instead, it produces FADH2. The production of NADH in the citrate cycle occurs during the reactions catalyzed by isocitrate dehydrogenase, alpha-ketoglutarate dehydrogenase complex, and malate dehydrogenase.

Know more about Krebs cycle here :

brainly.com/question/6260517

#SPJ11

The empirical formula is the simplest whole-number ratio of the elements, which is C2H3O.

To determine the empirical formula of butanedione, follow these steps:

1. Convert the mass percent composition to grams. Since percentages add up to 100%, assume you have a 100 g sample. This means you have:
  - 55.80 g of Carbon (C)
  - 7.03 g of Hydrogen (H)
  - 37.17 g of Oxygen (O)

2. Convert the grams of each element to moles by dividing the grams by their respective atomic masses:
  - For Carbon: (55.80 g) / (12.01 g/mol) ≈ 4.65 mol
  - For Hydrogen: (7.03 g) / (1.01 g/mol) ≈ 6.96 mol
  - For Oxygen: (37.17 g) / (16.00 g/mol) ≈ 2.32 mol

3. Divide the moles of each element by the smallest number of moles to obtain the mole ratio:
  - For Carbon: 4.65 / 2.32 ≈ 2
  - For Hydrogen: 6.96 / 2.32 ≈ 3
  - For Oxygen: 2.32 / 2.32 ≈ 1

to know more about empirical formula refer here:

https://brainly.com/question/11588623#

#SPJ11

Answer:

The correct statements regarding vacuum filtration are:

A short-stem funnel can be used for a vacuum filtration.

The size of the funnel must be adjusted based on the quantities being handled.

Explanation:

Vacuum filtration is a technique commonly used in chemistry labs to separate solids from liquids. A short-stem funnel is often used as it provides a better seal with the filter paper. The size of the funnel is chosen based on the volume of the liquid being filtered. If it is too small, the liquid will take longer to pass through the filter, and if it is too large, the filter paper may tear or the solid may not be retained properly. However, some statements regarding vacuum filtration are incorrect. Filter paper can be used with a wide range of solutions, including acidic and basic ones, as long as the filter paper is compatible with the solution. A hirsch funnel requires filter paper to function correctly. Lastly, vacuum filtration should be avoided with boiling solutions as the filter paper can disintegrate or the flask may crack under the pressure. Instead, hot filtration is used by filtering the solution while it is hot and then allowing it to cool to room temperature before collecting the solid.

The correct options are: 1, 2, and 4. Vacuum filtration is a commonly used technique in chemistry for separating solids from liquids. It involves using a vacuum to create a pressure difference across a filter, causing the liquid to be drawn through the filter while leaving the solid behind.

The technique is used in a variety of applications, such as separating precipitates from solutions or collecting cells from a culture. The following statements are correct regarding a vacuum filtration:

1. A short-stem funnel can be used for a vacuum filtration.

2. The solution cannot be too acidic or too basic when using filter paper.

3. No filter paper is needed when using a Hirsch funnel.

4. The size of the funnel must be adjusted based on the quantities being handled.

Therefore, correct options are: 1, 2, and 4.

When performing a vacuum filtration, it is important to select the appropriate size and type of funnel for the amount and type of material being filtered. It is also crucial to choose the correct filter paper, which should be compatible with the chemical properties of the solution being filtered. The use of a fritted glass filter or a Hirsch funnel may be necessary in some cases.

Vacuum filtration can be a time-saving and efficient method of separating solids and liquids, but it is important to carefully follow proper techniques and safety precautions to avoid any accidents or contamination.

To learn more about Vacuum filtration here:

https://brainly.com/question/31326542

#SPJ11

The addition of concentrated nitric acid to each standard solution results in a relatively constant ionic strength across the standard solutions is true. Adding concentrated nitric acid to the standard solutions results in a low pH (less than 2) because the acid is strong. The correct answer is option a and c.

The addition of concentrated nitric acid to each standard solution results in a low pH, which is required for this experiment is false.

The purpose of adding concentrated nitric acid to each standard solution is to make the ionic strength in all the standard solutions relatively constant. This makes it possible to estimate the Standard Electrode Potentials and the activity coefficients of Ag+ solutions.

The addition of concentrated nitric acid to each standard solution changes the potential of the reference electrode is false. The potential of the reference electrode will remain constant because the same reference electrode will be used for all measurements.

The addition of concentrated nitric acid does not affect the potential of the reference electrode results in a high pH, which is required by this experiment is false.

The low pH is required for the formation of the silver/silver chloride reference electrode. The low pH also helps to keep AgCl in solution.

The addition of concentrated nitric acid to each standard solution results in the required amount of excess nitrate ion is false. The amount of excess nitrate ion will depend on the concentration of the Ag+ solution being tested. The role of nitrate ion is to increase the solubility of AgCl.

Therefore, the amount of nitrate ion required will be different for each Ag+ solution.

The correct answer is option a and c.

To know more about nitric acid refer to-

brainly.com/question/17354612#
#SPJ11

Answer:

final temperature of gas = 512 Kelvin (or 239°C)

Explanation:

It's all about Charles' law

Charles' law: The volume of an ideal gas is directly proportional to the absolute temperature AT CONSTANT PRESSURE.

then, we conclude that:

[tex]\frac{V_1}{T_1 } = \frac{V_2}{T_2}[/tex]

in which V1 : initial volume in Liters, T1: initial temperature in Kelvin, V2: final volume in Liters, T2: final temperature in Kelvin.

*Temperature in Kelvin = Temperature in Celsius + 273

GIVEN THAT:

T1 = 200K,
V1 = 2.5L
V2 = 6.4L

By substituting in Charles' formula:

[tex]\frac{2.5}{200} = \frac{6.4}{T_2}[/tex]

Then:

[tex]T_2 = \frac{6.4 \times 200}{2.5} = 512 Kelvin[/tex]

Any Questions? write in the comments below.

The verse exhorts us to pray by God's will because it assures us that if we make a request that is in harmony with his plans, he will hear us and grant our desire.

In the meantime, James 5:15–16 exhorts us to confess our faults to one another and to pray for bodily healing, knowing that a good person's ardent prayer has enormous power and can be successful in bringing about healing and forgiveness.

These verses demonstrate to us the importance of prayer in our relationship with God and the potency of prayer in meeting both spiritual and material demands. I will try to pray more firmly as I apply these verses to my daily life, believing that God hears my prayers and will grant them by his will. I shall also bear in mind to offer prayers for my own and others' bodily well-being.

To know more about prayer here:

brainly.com/question/4046959

#SPJ1

The oxidation number of iron in Fe3O7 is not constant, but the average oxidation number of iron in this compound is 4.67.

To find the average oxidation number of iron (Fe) in Fe3O7, we can use the fact that the sum of the oxidation numbers of all atoms in a neutral molecule or compound is equal to zero.

Let the oxidation number of Fe be x. The oxidation number of oxygen (O) is -2.

The compound Fe3O7 contains 3 iron atoms and 7 oxygen atoms. Using the fact that the sum of the oxidation numbers is zero, we can set up the following equation:

3x + 7(-2) = 0

Solving for x, we get:

3x - 14 = 0

3x = 14

x = 4.67

Therefore, the average oxidation number of iron in Fe3O7 is 4.67, the average oxidation number is not restricted to integer values.

To learn more about average oxidation number, refer:

https://brainly.com/question/29201509

#SPJ4

There are approximately 1.998 x 10^23 copper atoms in a 79 g sample of Monel.

Monel is an alloy of nickel and copper that contains 28% copper. This means that 100 g of the alloy contains 28 g of copper. To find the amount of copper in a 79 g sample of Monel, we can set up a proportion:

[tex]\dfrac{28\text{ g Cu}}{100\ g} = \dfrac{x\text{ g Cu}}{79\ g}[/tex]

Cross-multiplying, we get:

28 g Cu * 79 g = 100 g * x g Cu

Simplifying

x g Cu = (28 g Cu * 79 g) / 100 g

x g Cu = 22.12 g Cu

To find the number of copper atoms in this amount of copper, we can use Avogadro's number, which tells us the number of atoms in a mole of a substance:

1 mole Cu = 63.55 g Cu contains 6.022 x 10^23 atoms of Cu

Therefore, the number of copper atoms in 22.12 g of copper is:

(22.12 g Cu) / (63.55 g Cu/mol) * (6.022 x 10^23 atoms Cu/mol) = 1.998 x 10^23 atoms of Cu

To know more about alloy, here

brainly.com/question/18404834

#SPJ4

The pH at the equivalence point of a weak base-strong acid titration can be determined using the balanced chemical equation and the stoichiometry of the reaction.

In this case, the weak base is not specified, so it is not possible to calculate the exact pH. However, given the volumes and concentrations of NaOCl and HCl used, it is possible to calculate the number of moles of each substance involved in the reaction. Then, using the balanced chemical equation and the stoichiometry, it is possible to determine the number of moles of the weak base and the resulting pH at the equivalence point.

Learn more about pH ,

https://brainly.com/question/2288405

#SPJ4

180.3 grams of Zn are necessary to completely react with 0.400 L of 4.60 M [tex](Fe_2(SO_4)_3)[/tex] solution.

The balanced chemical equation for the reaction between solid zinc (Zn) and aqueous iron(III) sulfate [tex](Fe_2(SO_4)_3)[/tex] can be written as:

[tex]2 Fe_2(SO_4)_3 + 3 Zn = 3 ZnSO_4 + 2 Fe_2O_3[/tex]

According to the stoichiometry of the balanced equation, 3 moles of Zn react with 2 moles of [tex]Fe_2(SO_4)_3[/tex]. We can use this ratio to calculate the moles of Zn required to react with 0.400 L of 4.60 M [tex](Fe_2(SO_4)_3)[/tex] solution:

moles of [tex](Fe_2(SO_4)_3)[/tex] = Molarity x Volume

moles of [tex](Fe_2(SO_4)_3)[/tex] = 4.60 M x 0.400 L = 1.84 mole

moles of Zn = (3/2) x moles of [tex](Fe_2(SO_4)_3)[/tex]

moles of Zn = (3/2) x 1.84 = 2.76 moles

Finally, we can use the molar mass of Zn to convert the moles of Zn to grams:

mass of Zn = moles of Zn x molar mass of Zn

mass of Zn = 2.76 moles x 65.38 g/mol = 180.3 g

For more question on Zn click on

https://brainly.com/question/19535295

#SPJ11

The correct option is (b) the solution is neutral. The solution is prepared by adding 0.10 mol of [tex]LiNO_3[/tex] to 1.00 L of water is a neutral solution.

Lithium nitrate ([tex]LiNO_3[/tex]) is an ionic compound that dissociates into ions when dissolved in water:

[tex]LiNO_3[/tex] → [tex]Li^+[/tex] (aq) + [tex]NO_3^-[/tex](aq)

[tex]Li^+[/tex] and  [tex]NO_3^-[/tex] are both spectator ions, which means they don't participate in acid-base reactions. Therefore, the acidity of the solution will be determined by the reaction between water and the remaining ions.

Since neither [tex]Li^+[/tex] nor [tex]NO_3^-[/tex] reacts with water, the solution will be neutral. It is important to note that the [tex]K_a[/tex] and [tex]K_b[/tex] values of the species in solution do not need to be known in order to predict the acidity of the solution, since [tex]Li^+[/tex] and [tex]NO_3^-[/tex] are both spectator ions and do not participate in acid-base reactions.

Therefore, the correct option is (b) the solution is neutral.

for more such question on neutral solution

https://brainly.com/question/9395871

#SPJ11

Based on the description provided by the science teacher, the correct flask is an Erlenmeyer flask. Erlenmeyer flasks have a flat bottom, a narrow opening, and a cone-shaped base.

The cone-shaped base helps in swirling the contents of the flask and prevents spills during the mixing of liquids. The narrow opening helps in controlling the rate of gas exchange and minimizes the risk of contamination. Erlenmeyer flasks are commonly used in chemistry laboratories for mixing, heating, and storing liquids. They are also used in the preparation of solutions and in titration experiments. Their design makes them easy to handle and they are also stackable, which saves flask space in the laboratory. Based on the description provided by the science teacher, the correct flask is an Erlenmeyer flask. Erlenmeyer flasks have a flat bottom, a narrow opening, and a cone-shaped base.

Learn more about flask here

https://brainly.com/question/30463444

#SPJ1

The pH of the solution after the addition of each of the given amounts of HCL is 2.58.

Molarity of KOH is  0.107 M

Volume of KOH solution is 50 mL

Molarity of HCL is 0.214 M

Volume of HCL solution is 26 mL

The moles can be calculated as,

Moles of KOH = molarity of the solution × volume(L)

                       =0.107M×50mL×1L / 1000mL

                       =0.0053mole

Moles of HCL = molarity of the solution × volume(L)

                     =0.214M×26mL×1L / 1000mL

                     =0.0055mole

The remaining HCL solution can be calculated as,

Remaining HCL solution = −0.0055mole - 0.0053 mole

                                        =0.0002mole

Total Volume = 50+26m

                      = 76mL× 1L1000mL= 0.076L

The concentration of hydroxide ion is ,

[H+] = moles /volume(L) = 0.0002mole / 0.076L= 0.0026M

The pH is calculated as ,

pH=−log[H+]

    =−log[0.0026]

    =  2.58

To learn more about pH

https://brainly.com/question/26424076

#SPJ4

The complete question is,

A 50.0 ml solution of 0.107 m KOH is titrated with 0.214 m HCL . calculate the pH of the solution after the addition of 26ml of HCL .

Chemical reaction characteristics. A shift in colour. a shift in the temperature. State change. creation of new materials.

Flammability, cytotoxicity, acidity, reactivity (of various kinds), and heat of combustion are a few examples of chemical qualities. Rust, for instance, is created when iron and oxygen interact in the when water is present; chromium does not oxidise ([link]).

The five basic types of chemical reactions are combination, decomposition, one, double replacement, and combustion. By analysing the reactants and products, you can assign a reaction to one of these categories.

To know more about temperature visit:

https://brainly.com/question/14633960

#SPJ1

Ferrous iron[tex](Fe2+)[/tex]oxidation generally occurs in environments with high oxygen content. The correct option is a.

This is because the oxidation process involves the conversion of ferrous ions [tex](Fe2+)[/tex] to ferric ions [tex](Fe3+)[/tex]through a reaction with oxygen. Oxidation is the process by which a substance loses electrons.

Ferrous iron [tex](Fe2+)[/tex] oxidation involves the loss of two electrons. Ferrous iron can be oxidized by a variety of substances, including oxygen, nitrate, and manganese. However, it is most commonly oxidized by oxygen.

The rate of ferrous iron oxidation depends on a number of factors, including temperature, pH, and the presence of other chemicals.

In general, ferrous iron oxidation occurs more quickly in environments with acidic conditions.

This is because the hydrogen ions in acidic solutions can react with ferrous iron to form ferric iron [tex](Fe3+)[/tex], which is more stable and less soluble than ferrous iron. As a result, it precipitates out of the solution, which makes it easier to remove.

to know more about oxidation refer here:

https://brainly.com/question/9347985#

#SPJ11
.

The correct answer is option B. Codeine is a drug made by changing one of the hydroxyl groups in morphine to a methyl ether group.

It is an opioid analgesic used to treat coughing, diarrhoea, and other illnesses as well as mild to moderate pain. The opioid medication class includes codeine, which is made from the opium plant. In order to lessen the experience of pain, it functions by attaching to opioid receptors in the brain, spinal cord, and gastrointestinal system.

To increase its benefits and lower the danger of addiction, it is frequently administered in conjunction with other drugs, such as paracetamol.

Codeine comes in pill, liquid, and injection forms, and it is occasionally mixed with other drugs such expectorants, decongestants, and antihistamines.

Although codeine can become habit-forming and addictive if used in high dosages or for longer periods of time than recommended, it is crucial to follow a doctor's instructions properly.

Complete Question:

Which drug is made by changing one of the hydroxyl groups in morphine to a methyl ether group?

A. Nicotine

B. Codeine

C. Ketamine

D. THC

To learn more about Codeine visit:

https://brainly.com/question/8965641

#SPJ4

In a hydrogen atom, the 2s and 2p subshells have the same energy.

The 4px, 4py, and 4pz orbitals look the same, but they point in different directions.

i. This statement is incorrect. The 3px and 4px orbitals in a calcium atom have different sizes and shapes because they belong to different energy levels. The orbitals at higher energy levels are larger and more diffuse than those at lower energy levels.

ii. This statement is correct. In a hydrogen atom, the 2s and 2p subshells have the same energy. This is due to the fact that they have the same principal quantum number (n=2), which determines the overall energy level of the subshell.

iii. This statement is also correct. The 4px, 4py, and 4pz orbitals are all part of the same energy level and have the same size and shape. However, they point in different directions along the x, y, and z axes of the coordinate system.

iv. This statement is incorrect. The number of orbitals in a given d subshell is actually 5. The d subshell consists of five orbitals with different orientations and shapes: dxy, dyz, dxz, dx2-y2, and dz2.

Learn more about Subshells here:

brainly.com/question/30790772

#SPJ4

Endothermic and exothermic reactions are two types of chemical reactions. In an endothermic reaction, the energy is absorbed from the surroundings, resulting in a decrease in temperature. On the other hand, in an exothermic reaction, energy is released into the surroundings, resulting in an increase in temperature. In other words, endothermic reactions require energy to be put in, while exothermic reactions release energy. An example of an endothermic reaction is photosynthesis, while combustion is an example of an exothermic reaction.