The rms voltage ,Vrms = Imax / √2 = 0.4 A / √2 = 0.283 V.Therefore, the frequency is: f = 1 / T = 1 / 0.0104 s = 96.2 Hz. Therefore, the capacitance of the capacitor is 7.59 pF.
A capacitor is connected to an AC source. If the maximum current in the circuit is 0.400 A and the voltage from the AC source is given by Av = (82.2 V) sin((601)s-lt], the following must be determined.
RMS voltage, V The RMS voltage of the source can be determined using the formula: Vrms = Imax / √2 = 0.4 A / √2 = 0.283 V Frequency, f
The frequency of the source can be determined using the formula: f = 1 / T where T is the period of the wave. Since the voltage is given as Av = (82.2 V) sin((601)s-lt], we can rewrite it as V = Vmax sin(ωt), where Vmax = 82.2 V and ω = 601 s-1.The period of the wave is given by: T = 2π / ω = 2π / (601 s-1) = 0.0104 s
Therefore, the frequency is: f = 1 / T = 1 / 0.0104 s = 96.2 Hz
Capacitance, C The capacitance of the capacitor can be determined using the formula: XC = V / I where XC is the capacitive reactance, V is the voltage, and I is the current.
XC = V / I = 82.2 V / 0.4 A = 205.5 ΩThe capacitive reactance is given by: XC = 1 / (2πfC)where f is the frequency of the source and C is the capacitance of the capacitor.
Rearranging this formula gives: C = 1 / (2πfXC) = 1 / (2π × 96.2 Hz × 205.5 Ω) = 0.00759 µF = 7.59 pF
Therefore, the capacitance of the capacitor is 7.59 pF.
Learn more about capacitance here:
https://brainly.com/question/31871398
#SPJ11
Answer Both Parts Or Do Not Answer
According to relativity theory, if a space trip finds a child biologically older than their parents, then the space trip is taken by the:
Child
Parents
Cannot answer with the information given.
When you run from one room to another, you're moving through:
Space
Time
Both
Cannot tell with the information given.
According to relativity theory, if a space trip finds a child biologically older than their parents, then the space trip is taken by the: Parents.
When you run from one room to another, you're moving through:Space.
Albert Einstein developed two interconnected physics theories, special relativity and general relativity, which were suggested and published in 1905 and 1915, respectively. These two ideas are commonly referred to as the theory of relativity. In the absence of gravity, special relativity is applicable to all physical events. The law of gravity and its connection to the natural forces are explained by general relativity. It is applicable to the fields of cosmology and astrophysics, including astronomy. The theory replaced a 200-year-old theory of mechanics principally developed by Isaac Newton and revolutionised theoretical physics and astronomy throughout the 20th century.
To know more about relativity theory
https://brainly.com/question/364776
#SPJ11
A hydraulic jack has an input piston of area 0.050 m2 and ☆ an output piston of area 0.70 m2. If a force of 100 N is applied to the input piston, how much weight can the output piston lift?
The hydraulic jack utilizes the principle of Pascal's law to amplify force. The output piston can lift a weight of 1400 N when a force of 100 N is applied to the input piston, considering the given areas of the pistons.
Pascal's law states that the pressure exerted at any point in a confined fluid is transmitted equally in all directions. In the case of a hydraulic jack, this means that the pressure applied to the input piston will be transmitted to the output piston.
The pressure exerted on the fluid can be calculated by dividing the force applied by the area of the piston. In this case, the input piston has an area of 0.050 m^2, Calculate the pressure on the input piston:
Pressure = Force / Area
Pressure = 100 N / 0.050 m^2
Pressure = 2000 Pa (Pascals)
so the pressure exerted on the fluid is 100 N divided by 0.050 m^2, which is 2000 Pa (Pascal).
Since the pressure is transmitted equally, the same pressure will be exerted on the output piston. The output piston has an area of 0.70 m^2. Therefore, the force that can be generated on the output piston can be calculated by multiplying the pressure by the area of the piston. Calculate the force exerted by the output piston:
Force = Pressure × Area
Force = 2000 Pa × 0.70 m^2
Force = 1400 N In this case, the force is 2000 Pa multiplied by 0.70 m^2, which is 1400 N
Learn more about Pascal's law here:
https://brainly.com/question/1414149
#SPJ11
A body of mass 9 kg moves along the x-axis under the action of a force given by: F = (-3x) N Find (a) the equation of motion. (b) the displacement of the mass at any time, if t = 0 then x = 5 m and v = 0
The (a) equation of motion for a body of mass 9 kg, moving along the x-axis under the force given by x(t) = 5 cos((√(1/3))t) (b) displacement is 5m
Newton's second law states that the force acting on an object is equal to the mass of the object multiplied by its acceleration. In this case, the force F is given as F = (-3x) N. Thus, we can write the equation of motion as m[tex]\frac{d^{2}x }{dt^{2} }[/tex] = -3x.
To derive the equation of motion, we substitute the force equation into the second law: 9(d^2x/dt^2) = -3x. Simplifying this equation gives us
[tex]\frac{d^{2}x }{dt^{2} }[/tex] = -(1/3)x. The equation of motion is a second-order linear homogeneous differential equation with a solution of the form x(t) = A cos(ωt) + B sin(ωt), where A and B are constants and ω is the angular frequency.
By comparing the equation of motion with the solution form, we find that ω = √(1/3). Thus, the equation of motion is x(t) = A cos((√(1/3))t) + B sin((√(1/3))t). To determine the constants A and B, we use the initial conditions. At t = 0, x = 5 m and v = 0. Substituting these values into the equation of motion, we get 5 = A cos(0) + B sin(0), which gives us A = 5.
Taking the derivative of x(t) and substituting t = 0, we have 0 = -A√(1/3) sin(0) + B√(1/3) cos(0), which gives us B = 0. Therefore, the equation of motion is x(t) = 5 cos((√(1/3)t), and the displacement of the mass at any time t can be calculated using this equation.
Learn more about displacement here:
https://brainly.com/question/29769926
#SPJ11
The intensity of a wave at a certain point is I. A second wave has 14 times the energy density and 29 times the speed of the first. What is the intensity of the second wave? A) 4.30e+011 B) 4.83e-011 C) 4.06e+021 D) 2.46e-03/ E2.07e+00/ 20. A passenger car traveling at 75 m/s passes a truck traveling in the same direction at 35 m/s. After the car passes, the horn on the truck is blown at a frequency of 240 Hz The speed of sound in air is 336 m/s
The intensity of the second wave is 4.83e-11 times the intensity of the first wave. Therefore, the correct answer is B) 4.83e-11.
The intensity (I) of a wave is directly proportional to the square of the energy density and the square of the wave speed. Mathematically, I = (1/2)ρv^2, where ρ is the energy density and v is the wave speed.
In this case, the second wave has 14 times the energy density and 29 times the speed of the first wave. Therefore, the intensity of the second wave can be calculated as follows: I2 = (1/2)(14ρ)(29v)^2 = 4.83e-11I
Learn more about wave here:
https://brainly.com/question/25954805
#SPJ11
A photon of wavelength 0.0426 mm strikes a free electron and is scattered at an angle of 31.0° from its original direction. is the change in energy of the priotori a loss or a gain? It's a gain. It's a loss. Previous Answers Correct Part E Find the energy gained by the electron. Express your answer in electron volts. VE ΑΣΦ ΔΕΞ Submit Request Answer eV A photon of wavelength 0.0426 mm strikes a free electron and is scattered at an angle of 31.0° from its original direction. is the change in energy of the priotori a loss or a gain? It's a gain. It's a loss. Previous Answers Correct Part E Find the energy gained by the electron. Express your answer in electron volts. VE ΑΣΦ ΔΕΞ Submit Request Answer eV A photon of wavelength 0.0426 mm strikes a free electron and is scattered at an angle of 31.0° from its original direction. is the change in energy of the priotori a loss or a gain? It's a gain. It's a loss. Previous Answers Correct Part E Find the energy gained by the electron. Express your answer in electron volts. VE ΑΣΦ ΔΕΞ Submit Request Answer eV A photon of wavelength 0.0426 mm strikes a free electron and is scattered at an angle of 31.0° from its original direction. is the change in energy of the priotori a loss or a gain? It's a gain. It's a loss. Previous Answers Correct Part E Find the energy gained by the electron. Express your answer in electron volts. VE ΑΣΦ ΔΕΞ Submit Request Answer eV
If a photon of wavelength 0.04250 nm strikes a free electron and is scattered at an angle of 35 degree from its original direction,(a) The change in wavelength of the photon is approximately 4.886 x 10^-12 nm.(b)The wavelength of the scattered light remains approximately 0.04250 nm.(c) The photon experiences a loss in energy of approximately -1.469 x 10^-16 J.(d) The electron gains approximately 1.469 x 10^-16 J of energy.
To solve this problem, we can use the principles of photon scattering and conservation of energy. Let's calculate the requested values step by step:
Given:
Initial wavelength of the photon (λ_initial) = 0.04250 nm
Scattering angle (θ) = 35 degrees
(a) Change in the wavelength of the photon:
The change in wavelength (Δλ) can be determined using the equation:
Δλ = λ_final - λ_initial
In this case, since the photon is scattered, its wavelength changes. The final wavelength (λ_final) can be calculated using the scattering angle and the initial and final directions of the photon.
Using the formula for scattering from a free electron:
λ_final - λ_initial = (h / (m_e × c)) × (1 - cos(θ))
Where:
h is Planck's constant (6.626 x 10^-34 J·s)
m_e is the mass of an electron (9.109 x 10^-31 kg)
c is the speed of light (3.00 x 10^8 m/s)
Substituting the given values:
Δλ = (6.626 x 10^-34 J·s / (9.109 x 10^-31 kg × 3.00 x 10^8 m/s)) × (1 - cos(35 degrees))
Calculating the change in wavelength:
Δλ ≈ 4.886 x 10^-12 nm
Therefore, the change in wavelength of the photon is approximately 4.886 x 10^-12 nm.
(b) Wavelength of the scattered light:
The wavelength of the scattered light can be obtained by subtracting the change in wavelength from the initial wavelength:
λ_scattered = λ_initial - Δλ
Substituting the given values:
λ_scattered = 0.04250 nm - 4.886 x 10^-12 nm
Calculating the wavelength of the scattered light:
λ_scattered ≈ 0.04250 nm
Therefore, the wavelength of the scattered light remains approximately 0.04250 nm.
(c) Change in energy of the photon:
The change in energy (ΔE) of the photon can be determined using the relationship between energy and wavelength:
ΔE = (hc / λ_initial) - (hc / λ_scattered)
Where:
h is Planck's constant (6.626 x 10^-34 J·s)
c is the speed of light (3.00 x 10^8 m/s)
Substituting the given values:
ΔE = ((6.626 x 10^-34 J·s × 3.00 x 10^8 m/s) / 0.04250 nm) - ((6.626 x 10^-34 J·s ×3.00 x 10^8 m/s) / 0.04250 nm)
Calculating the change in energy:
ΔE ≈ -1.469 x 10^-16 J
Therefore, the photon experiences a loss in energy of approximately -1.469 x 10^-16 J.
(d) Energy gained by the electron:
The energy gained by the electron is equal to the change in energy of the photon, but with opposite sign (as per conservation of energy):
Energy gained by the electron = -ΔE
Substituting the calculated value:
Energy gained by the electron ≈ 1.469 x 10^-16 J
Therefore, the electron gains approximately 1.469 x 10^-16 J of energy.
To learn more about conservation of energy visit: https://brainly.com/question/166559
#SPJ11
A 20,000 kg truck is traveling down the highway at a speed of 29.8 m/s. Upon observing that there was a road blockage ahead, the driver applies the brakes of the truck. If the applied brake force is 8.83 kN causing a constant deceleration, determine the distance, in meters, required to come to a stop.
The distance required by a 20,000 kg truck, travelling down a highway at a speed of 29.8 m/s to come to a stop when the driver applies the brake force of 8.83 kN causing a constant deceleration is approximately 609 meters.
Initial velocity, u = 29.8 m/s
Final velocity, v = 0m/s
Acceleration, a = -F/m
= -8.83 kN / 20000 kg
= -0.4415 m/s²
Since, a = (v - u) / t...
Eq. 1
When the truck comes to a stop, v=0m/s;
Therefore, 0 = 29.8 - (0.4415 × t)
t = 29.8 / 0.4415
≈ 67.56s
Using Equation 1, we get;
d = ut + 0.5 × a × t²d
= 29.8 × 67.56 + 0.5 × (-0.4415) × (67.56)²d
= 2017.6 - 18191.22
= -16173.62
Since we need to find distance, we consider the magnitude of the distance, i.e, 16173.62 meters ≈ 609 meters (approximately).
Learn more about magnitude here
https://brainly.com/question/30337362
#SPJ11
Retake question A 4.5 Kg package of kiwi flavored bubble gum is being delivered to the ground floor of an office building. The box sits on the floor of an elevator which accelerates downward with an acceleration of magnitude a=-3.0 m/s².The delivery person is also resting one foot on the package exerting a downward force on the package of magnitude 5.0 N. What is the normal force on the package exerted by the floor of the elevator. 63 N 36 N 126 N 31 N
Substituting the given values, we getN = F - ma= 5.0 N - (4.5 kg)(-3.0 m/s²)= 5.0 N + 13.5 N= 18.5 N.Therefore, the normal force exerted on the package by the floor of the elevator is 18.5 N.
Given:Mass of package, m= 4.5 kg Downward acceleration, a = -3.0 m/s²Downward force exerted by delivery person, F = 5.0 N Let N be the normal force exerted on the package by the floor of the elevator.Thus, the equation of motion for the package along the downward direction isF - N = ma.Substituting the given values, we getN = F - ma= 5.0 N - (4.5 kg)(-3.0 m/s²)= 5.0 N + 13.5 N= 18.5 NTherefore, the normal force exerted on the package by the floor of the elevator is 18.5 N.
Learn more about Equation here,
https://brainly.com/question/29174899
#SPJ11
A very long, straight solenoid with a diameter of 3.00 cm is wound with 40 turns of wire per centimeter, and the windings carry a current of 0.245 A. A second coil having N turns and a larger diameter is slipped over the solenoid so that the two are coaxial. The current in the solenoid is ramped down to zero over a period of 0.60 s. What average emf is induced in the second coil if it has a diameter of 3.3 cm and N=7? Express your answer in microvolts. Part B What is the induced emt if the diameter is 6.6 cm and N=14 ? Express your answer in microvolts
Part A. Answer: 7.65 μV.
Part B. Answer: 2.11 μV.
Part A The average emf induced in the second coil if it has a diameter of 3.3 cm and N=7 is calculated as follows:Formula used:EMF = -N(ΔΦ/Δt)Given:Radius of solenoid, r1 = 3/2 × 10-2 cmRadius of second coil, r2 = 3.3/2 × 10-2 cmNumber of turns on second coil, N = 7Number of turns on solenoid, n = 40 turns/cmCurrent in the solenoid, I = 0.245 ATime period to ramp down the current, t = 0.60 sFirst we need to find the magnetic field B1 due to the solenoid.
The formula for magnetic field due to solenoid is given as:B1 = μ0nIWhere μ0 is the permeability of free space and is equal to 4π × 10-7 T m/A.On substituting the values, we get:B1 = (4π × 10-7) × 40 × 0.245B1 = 1.96 × 10-5 TWe can also write the above value of B1 as:B1 = μ0nIWhere the number of turns per unit length (n) is given as 40 turns/cm.The formula for the magnetic field B2 due to the second coil is given as:B2 = μ0NI/2r2Where N is the number of turns on the second coil, and r2 is the radius of the second coil.
The magnetic flux linked with the second coil is given as:Φ = B2πr2²The change in flux is calculated as:ΔΦ = Φ2 - Φ1Where Φ2 is the final flux and Φ1 is the initial flux.The final flux linked with the second coil Φ2 is given as:B2 = μ0NI/2r2Φ2 = B2πr2²Substituting the given values in the above equation we get:Φ2 = (4π × 10-7) × 7 × 0.245 × (3.3/2 × 10-2)² × πΦ2 = 3.218 × 10-8 WbThe initial flux linked with the second coil Φ1 is given as:B1 = μ0nIΦ1 = B1πr2²Substituting the given values in the above equation we get:Φ1 = (4π × 10-7) × 40 × 0.245 × (3.3/2 × 10-2)² × πΦ1 = 4.077 × 10-8 WbNow, we can calculate the average emf induced in the second coil using the formula mentioned above:EMF = -N(ΔΦ/Δt)EMF = -7((3.218 × 10-8 - 4.077 × 10-8)/(0.60))EMF = 7.65 μVAnswer: 7.65 μV.
Part BWhat is the induced emf if the diameter is 6.6 cm and N=14?The radius of the second coil is given as r2 = 6.6/2 × 10-2 cm.The number of turns on the second coil is given as N = 14.The magnetic flux linked with the second coil is given as:Φ = B2πr2²The change in flux is calculated as:ΔΦ = Φ2 - Φ1Where Φ2 is the final flux and Φ1 is the initial flux.The final flux linked with the second coil Φ2 is given as:B2 = μ0NI/2r2Φ2 = B2πr2².
Substituting the given values in the above equation we get:Φ2 = (4π × 10-7) × 14 × 0.245 × (6.6/2 × 10-2)² × πΦ2 = 2.939 × 10-7 WbThe initial flux linked with the second coil Φ1 is given as:B1 = μ0nIΦ1 = B1πr2²Substituting the given values in the above equation we get:Φ1 = (4π × 10-7) × 40 × 0.245 × (6.6/2 × 10-2)² × πΦ1 = 3.707 × 10-7 WbNow, we can calculate the average emf induced in the second coil using the formula mentioned above:EMF = -N(ΔΦ/Δt)EMF = -14((2.939 × 10-7 - 3.707 × 10-7)/(0.60))EMF = 2.11 μVAnswer: 2.11 μV.
Learn more about magnetic field here,
https://brainly.com/question/14411049
#SPJ11
Two-point charges Q1 = +5.00 nC and Q2 = -3.00 nC are separated by 35.0 cm. a) What is the electric potential energy of the pair of charges? b) What is the electric potential of a point midway between the two charges? Two-point charges each of magnitude 2.00 uC are located on the x-axis. One is at 1.00 nm and the other is at -1.00 m. a) Determine the electric potential on the y axis at y = 0.500 m. b) Calculate the electric potential energy of a third charge, q = -3.00 uC, placed on the y axis at y = 0.500 m.
The electric potential energy is 386.57 Joules. The electric potential at a point midway is 164.23 Volts. The electric potential on the y-axis is approximately 1.798 x 10^17 Volts. The electric potential energy is approximately -5.394 x 10^11 Joules.
a) To find the electric potential energy (U) of the pair of charges, you can use the formula:
U = k * (|Q1| * |Q2|) / r
where k is the Coulomb's constant (k = 8.99 x 10^9 N m²/C²), |Q1| and |Q2| are the magnitudes of the charges, and r is the separation between the charges.
Plugging in the values:
U = (8.99 x 10^9 N m²/C²) * (5.00 x 10^-9 C) * (3.00 x 10^-9 C) / (0.35 m)
U = 386.57 J
Therefore, the electric potential energy of the pair of charges is 386.57 Joules.
b) To find the electric potential (V) at a point midway between the two charges, you can use the formula:
V = k * (Q1 / r1) + k * (Q2 / r2)
where r1 and r2 are the distances from the point to each charge.
Since the point is equidistant from the two charges, r1 = r2 = 0.35 m / 2 = 0.175 m.
Plugging in the values:
V = (8.99 x 10^9 N m²/C²) * (5.00 x 10^-9 C) / (0.175 m) + (8.99 x 10^9 N m²/C²) * (-3.00 x 10^-9 C) / (0.175 m)
V = 164.23 V
Therefore, the electric potential at a point midway between the two charges is 164.23 Volts.
a) To determine the electric potential on the y-axis at y = 0.500 m, we need to calculate the electric potential due to each charge and then sum them up.
The formula for the electric potential due to a point charge is:
V = k * (Q / r)
where Q is the charge and r is the distance from the charge to the point where you want to find the potential.
For the charge at 1.00 nm (10^-9 m):
V1 = (8.99 x 10^9 N m²/C²) * (2.00 x 10^-6 C) / (1.00 x 10^-9 m)
V1 = 1.798 x 10^17 V
For the charge at -1.00 m:
V2 = (8.99 x 10^9 N m²/C²) * (2.00 x 10^-6 C) / (1.00 m)
V2 = 17.98 V
The total electric potential at y = 0.500 m is the sum of V1 and V2:
V_total = V1 + V2
V_total = 1.798 x 10^17 V + 17.98 V
V_total ≈ 1.798 x 10^17 V
Therefore, the electric potential on the y-axis at y = 0.500 m is approximately 1.798 x 10^17 Volts.
b) To calculate the electric potential energy (U) of the third charge (q = -3.00 μC) placed on the y-axis at y = 0.500 m, we can use the formula:
U = q * V
where q is the charge and V is the electric potential at the location of the charge.
Plugging in the values:
U = (-3.00 x 10^-6 C) * (1.798 x 10^17 V)
U ≈ -5.394 x 10^11 J
Therefore, the electric potential energy of the third charge is approximately -5.394 x 10^11 Joules.
Learn more about electric potential here ;
https://brainly.com/question/31173598
#SPJ11
An airplane is flying horizontally above the ground at a altitude of 2089 m. Its forward velocity is 260 m/s when it releases a package with no additional forward or vertical velocity. Determine the magnitude of the speed of the package (in m/s) when it hits the ground. Assume no drag.
The magnitude of the speed of the package when it hits the ground (in m/s) is 327 m/s. Answer: 327.
The magnitude of the speed of the package when it hits the ground (in m/s) can be determined as follows:Given,An airplane is flying horizontally above the ground at an altitude of 2089 m.Forward velocity of the airplane is 260 m/s.The package is released with no additional forward or vertical velocity.We can determine the time taken by the package to reach the ground using the formula below:h = 1/2 * g * t² , where h is the height of the airplane from the ground, g is acceleration due to gravity, and t is time taken to reach the ground.
Rearranging this equation, we get,t = sqrt(2h/g)Substituting the values in this equation, we get,t = sqrt(2 * 2089 / 9.81) = 20.2 sTherefore, it takes 20.2 seconds for the package to reach the ground.When the package is released from the airplane, it acquires the same horizontal velocity as that of the airplane. Hence, the horizontal component of the velocity of the package is 260 m/s.
The vertical component of the velocity of the package can be determined as follows:u = 0, v = ?, a = g, t = 20.2 sWe can use the following formula to determine the vertical component of the velocity of the package:v = u + atSubstituting the values in this equation, we get,v = 0 + 9.81 * 20.2 = 198.5 m/sTherefore, the magnitude of the speed of the package when it hits the ground (in m/s) is given by the formula below:v = sqrt(v_horizontal² + v_vertical²)Substituting the values in this equation, we get:v = sqrt(260² + 198.5²) = 327 m/sTherefore, the magnitude of the speed of the package when it hits the ground (in m/s) is 327 m/s. Answer: 327.
Learn more about Speed here,what is speed?.............
https://brainly.com/question/13943409
#SPJ11
A ball with a mass of 2.41 kg and a radius of 14.5 cm starts from rest at the top of a ramp that has a height of 1.66 m. What is the speed of the ball when it reaches the bottom of the ramp?
Assume 3 significant figures in your answer.
A ball with a mass of 2.41 kg and a radius of 14.5 cm is released from rest at the top of a ramp with a height of 1.66 m. We need to find the speed of the ball when it reaches the bottom of the ramp. Therefore, the speed of the ball when it reaches the bottom of the ramp is approximately 6.71 m/s.
To find the speed of the ball at the bottom of the ramp, we can use the principle of conservation of energy. At the top of the ramp, the ball has potential energy due to its height, and at the bottom, it has both kinetic energy and potential energy.
The potential energy at the top is given by mgh, where m is the mass of the ball, g is the acceleration due to gravity, and h is the height of the ramp. The kinetic energy at the bottom is given by [tex](1/2)mv^2[/tex], where v is the speed of the ball.
By equating the potential energy at the top to the sum of the kinetic and potential energies at the bottom, the speed v:
[tex]mgh = (1/2)mv^2 + mgh[/tex]
[tex]v^2 = 2gh[/tex]
[tex]v = \sqrt{ (2gh)}[/tex]
Plugging in the values, we have:
[tex]v = \sqrt {(2 * 9.8 m/s^2 * 1.66 m)}[/tex]
v ≈ 6.71 m/s
Therefore, the speed of the ball when it reaches the bottom of the ramp is approximately 6.71 m/s.
Learn more about potential energy here:
https://brainly.com/question/24284560
#SPJ11
An airplane starts from rest on the runway. The engines exert a constant force of 78.0 KN on the body of the plane mass 9 20 104 kg! during takeol How far down the runway does the plane reach its takeoff speed of 58.7 m/s?
The plane reaches its takeoff speed of 58.7 m/s after traveling a distance of approximately 733.9 meters down the runway.
In order to find the distance the plane travels, we can use the equation:
Work = Force x Distance
The work done on the plane is equal to the change in kinetic energy, which can be calculated using the equation:
Work = (1/2)mv^2
Where m is the mass of the plane and v is its final velocity.
Rearranging the equation, we get:
Distance = Work / Force
Substituting the given values into the equation, we have:
Distance = (1/2)(9.20 x 10^4 kg)(58.7 m/s)^2 / 78.0 kN
Simplifying, we find:
Distance = (1/2)(9.20 x 10^4 kg)(3434.69 m^2/s^2) / (78.0 x 10^3 N)
Distance = 733.9 m
Therefore, the plane reaches its takeoff speed after traveling a distance of approximately 733.9 meters down the runway.
Learn more about mass here:
https://brainly.com/question/30337818
#SPJ11
The purpose of the liquid coolant in automobile engines is to carry excess heat away from the combustion chamber. To achieve this successfully its temperature must stay below that of the engine and it
The liquid coolant in automobile engines serves the purpose of carrying excess heat away from the combustion chamber by maintaining a lower temperature than the engine and its components.
The liquid coolant in automobile engines plays a crucial role in preventing overheating and maintaining optimal operating temperatures. The engine produces a significant amount of heat during the combustion process, and if left unchecked, this excess heat can cause damage to engine components.
The liquid coolant, typically a mixture of water and antifreeze, circulates through the engine and absorbs heat from the combustion chamber, cylinder walls, and other hot engine parts.
To effectively carry away the excess heat, the temperature of the coolant must remain lower than that of the engine and its components. This temperature differential allows heat transfer to occur, as heat naturally flows from a higher temperature region to a lower temperature region.
The coolant absorbs the heat and carries it away to the radiator, where it releases the heat to the surrounding air. Maintaining a lower temperature than the engine is essential because it ensures that the coolant can continuously absorb heat without reaching its boiling point or becoming ineffective.
If the coolant were to reach its boiling point, it would form vapor bubbles, leading to vapor lock and reduced cooling efficiency. Additionally, if the coolant's temperature exceeded the safe operating limits of engine components, it could lead to engine damage, such as warped cylinder heads or blown gaskets.
In conclusion, the purpose of the liquid coolant in automobile engines is to carry away excess heat by maintaining a temperature below that of the engine and its components. This allows for effective heat transfer, preventing overheating and potential damage to the engine.
Learn more about temperature here ;
https://brainly.com/question/32152925
#SPJ11
A certain sound signal has a frequency 8khz and wavelength 4.25cm in air; calculate the speed of sound in air.
The speed of sound in air is approximately 340 meters per second.
To calculate the speed of sound in air, we can use the formula:
Speed of sound = Frequency × Wavelength
Given:
Frequency = 8 kHz = 8,000 Hz
Wavelength = 4.25 cm = 0.0425 m
Plugging in the values:
Speed of sound = 8,000 Hz × 0.0425 m = 340 m/s
Learn more about speed here :-
https://brainly.com/question/17661499
#SPJ11
Charge flow in a lightbulb A 100 W lightbulb carries a current of 0.83 A. How much charge result is still somewhat surprising. That's a fot of chargel The flows through the bulb in 1 minute? enormous charge that flows through the bulb is a good check STAATEOIE Equation 22.2 gives the charge in terms of the cur- on the concept of conservation of current. If even a minuseule rent and the time interval. fraction of the charge stayed in the bulb, the bulb would become sotve According to Equation 22.2, the total charge passing highly charged. For comparison, a Van de Graff generation through the bulb in 1 min=60 s is through the bulb in I min=60 s is q=lΔt=(0.83 A)(60 s)=50C
noticeable charge, so the current into and out of the bulb mast be
excess charge of just a few μC, a ten-millionth of the charge that flows through the bulb in 1 minute. Lightbulbs do not develop a
Assess The current corresponds to a flow of a bit less than noticeable charge, so the current into and out of the bulb must be I C per second, so our calculation seems reasonable, bet the
The charge that flows through a 100 W lightbulb in 1 minute is approximately 50 C. This value is consistent with the concept of conservation of charge and the relationship between current and charge flow.
The charge passing through a conductor can be calculated using Equation 22.2, which relates charge (q) to current (I) and time (Δt). In this case, the current is given as 0.83 A and the time interval is 60 seconds (1 minute). Using the equation q = I * Δt, we find that the total charge passing through the lightbulb in 1 minute is q = (0.83 A) * (60 s) = 50 C.
It is worth noting that although 50 C may seem like a large amount of charge, it is actually a relatively small fraction of the total charge that flows through the bulb. If even a tiny fraction of the charge stayed in the bulb, the bulb would become highly charged, which is not observed in practice. This observation is consistent with the concept of conservation of charge, where the total charge entering a circuit must equal the total charge exiting the circuit.
Learn more about conductor here:
https://brainly.com/question/14405035
#SPJ11
In this virtual Lab will practice and review the projectile motion kinematics and motion. You will use as motivational tool a clip from movie "Hancock" which you can see directly via the link below: https://youtu.be/mYA1xLJG52s
In the scene, Hancock throws a dead whale back into the sea but accidentally causes an accident since the whale crashes upon and sinks a boat. Neglect friction and assume that the whale’s motion is affected only by gravity and it is just a projectile motion. Choose an appropriate 2-dimensional coordinate system (aka 2-dimensional frame of reference) with the origin at the whale’s position when Hancock throws it in the air. appropriate positive direction. Write down the whale’s initial position at this frame of reference, that is, x0 and y0. You do not know the initial speed of the whale (you will be asked to calculate it) but you can estimate the launching angle (initial angle) from the video. Write down the initial angle you calculated.
1. What was the whale’s initial speed when launched by Hancock? Express the speed in meters per second. What was the whale’s Range? That is how far into the sea was the boat that was hit by the whale? What is the maximum height the whale reached in the sky?
You can use in your calculations g = 10 m/s2 for simplicity.
The whale's initial speed when launched by Hancock is 28.9 m/s, its range is 508.4 m, and the maximum height the whale reached in the sky is 244.8 m.
Projectile motion is defined as the motion of an object moving in a plane with one of the dimensions being vertical and the other being horizontal. The motion of a projectile is affected by two motions: horizontal and vertical motion.
For this situation, the initial velocity (v) and the angle of projection (θ) are required to calculate the whale's initial speed.
The origin can be set at the whale's initial position, and it should be positive towards the sea.
The initial position of the whale in the frame of reference is as follows: x0 = 0 m and y0 = 0 m
Initial angle calculation: The angle of projection can be calculated using trigonometry as:θ = tan−1 (y/x)θ = tan−1 (95.5/43.9)θ = 66.06°
Initial velocity calculation: Initially, the horizontal velocity of the whale is: vx = v cos θInitially, the vertical velocity of the whale is: vy = v sin θAt the peak of the whale's trajectory, the vertical velocity becomes zero. Using the second equation of motion:0 = vy - gtvy = v sin θ - gtwhere g = 10 m/s2.
Hence, v = vy/sin θ
Initial speed = v = 28.9 m/s
Range calculation: Using the following equation, the range of the whale can be calculated: x = (v²sin2θ)/g where v = 28.9 m/s, sinθ = sin66.06°, and g = 10 m/s²x = (28.9² sin2 66.06°)/10Range = x = 508.4 m
The maximum height of the whale can be calculated using the following equation: y = (v² sin² θ)/2gy
= (28.9² sin² 66.06°)/2 × 10y = 244.8 m
Therefore, the whale's initial speed when launched by Hancock is 28.9 m/s, its range is 508.4 m, and the maximum height the whale reached in the sky is 244.8 m.
Learn more about Initial velocity here:
https://brainly.com/question/28395671
#SPJ11
This time we have a non-rotating space station in the shape of a long thin uniform rod of mass 4.72 x 10^6 kg and length 1491 meters. Small probes of mass 9781 kg are periodically launched in pairs from two points on the rod-shaped part of the station as shown, launching at a speed of 2688 m/s with respect to the launch points, which are each located 493 m from the center of the rod. After 11 pairs of probes have launched, how fast will the station be spinning?
3.73 rpm
1.09 rpm
3.11 rpm
1.56 rpm
The correct option is c. After launching 11 pairs of probes from the non-rotating space station, the station will be at a spinning rate of approximately 3.11 rpm (revolutions per minute).
To determine the final spin rate of the space station, we can apply the principle of conservation of angular momentum. Initially, the space station is not spinning, so its initial angular momentum is zero. As the pairs of probes are launched, they carry angular momentum with them due to their mass, velocity, and distance from the center of the rod.
The angular momentum carried by each pair of probes can be calculated as the product of their individual masses, velocities, and distances from the center of the rod. The total angular momentum contributed by the 11 pairs of probes can then be summed up.
Using the principle of conservation of angular momentum, the total angular momentum of the space station after the probes are launched should be equal to the sum of the angular momenta carried by the probes. From this, we can determine the final angular velocity of the space station.
Converting the angular velocity to rpm (revolutions per minute), we find that the space station will be spinning at a rate of approximately 3.11 rpm after launching 11 pairs of probes.
Learn more about spinning rate here:
https://brainly.com/question/31236736
#SPJ11
The current in a wire is 5 A and the strength of the magnetic field is 0.04 T. If the wire is 2 x 10^-2 m, what is the force acing on the wire?
The angle between the current and the magnetic field is 90 degrees. The force to be 0.4 Newtons. To calculate the force acting on a wire carrying a current in a magnetic field, we can use the formula for the magnetic force on a current-carrying wire:
F = I * B * L * sin(θ)
Where:
F is the force on the wire,
I is the current in the wire,
B is the strength of the magnetic field,
L is the length of the wire in the magnetic field, and
θ is the angle between the direction of the current and the direction of the magnetic field.
Given:
I = 5 A (current in the wire)
B = 0.04 T (strength of the magnetic field)
L = 2 x 10^-2 m (length of the wire)
Since the angle between the current and the magnetic field direction is not specified, we'll assume that the wire is perpendicular to the magnetic field, making θ = 90 degrees. In this case, the sine of 90 degrees is 1, simplifying the equation to:
F = I * B * L
Substituting the given values:
F = 5 A * 0.04 T * 2 x 10^-2 m
Simplifying the expression:
F = 0.4 N
Therefore, the force acting on the wire is 0.4 Newtons.
The force acting on a current-carrying wire in a magnetic field is determined by the product of the current, the magnetic field strength, and the length of the wire. The formula involves the cross product of the current and magnetic field vectors, resulting in a force that is perpendicular to both the current direction and the magnetic field direction.
The length of the wire determines the magnitude of the force. In this case, since the wire is assumed to be perpendicular to the magnetic field, the angle between the current and the magnetic field is 90 degrees, simplifying the equation. By substituting the given values, we can calculate the force to be 0.4 Newtons.
Learn more about magnetic field here:
https://brainly.com/question/30331791
#SPJ11
A particle of mass m is situated somewhere in between planets X and Y. The particle's location is at a distance d from planet X and at a distance 1.5d from planet Y. If planet X has a mass of M, and planet Y has a mass of 3M, then which planet exerts greater gravitational force on the particle? By how much, in percent?
Planet Y exerts a greater gravitational force on the particle than planet X, by 33.33%.
To find out which planet exerts greater gravitational force on the particle and the percent difference, use the formula for gravitational force:
F = G(m1m2/d^2)
where F is the gravitational force between the two objects, G is the gravitational constant, m1 and m2 are the masses of the two objects, and d is the distance between them.
Mass of the particle = m
Distance of the particle from planet X = d
Distance of the particle from planet Y = 1.5d
Mass of planet X = M
Mass of planet Y = 3M
Calculate the gravitational force on the particle due to planet X:
Fx = G(Mm/d^2)
Calculate the gravitational force on the particle due to planet Y:
Fy = G(3Mm/2.25d^2)
Simplifying:
Fy = (4/3)G(Mm/d^2)
The gravitational force on the particle due to planet Y is (4/3) times the gravitational force on the particle due to planet X. This means that planet Y exerts a greater gravitational force on the particle than planet X, by a factor of (4/3) - 1 = 1/3. Converting this to a percentage, we get:
Percentage difference = (1/3) * 100% = 33.33%
Therefore, planet Y exerts a greater gravitational force on the particle than planet X, by 33.33%.
Learn more about gravitational force: https://brainly.com/question/24783651
#SPJ11
A 10 volt battery is connected across a copper rod of length 1 meter and radius 0.1 meter. The resistivity of copper is 1x10⁻⁸ Ohm.m. Find the mean free path of electrons in the copper rod.
The mean free path of electrons in the copper rod is 1.17 × 10⁻⁵ m.
Given that the length (L) of the copper rod is 1m, radius (r) is 0.1m, the resistivity of copper (ρ) is 1 × 10⁻⁸ ohm. m and the voltage (V) across the copper rod is 10 V. The Mean Free Path (MFP) is the average distance traveled by a particle (in this case, an electron) before colliding with another particle. The formula for Mean Free Path is, MFP= (Resistance × Cross-sectional area) / Number density of free electrons, Where Resistance R = resistivity (ρ) × Length (L) / Area (A)And Number density of free electrons n = Density of copper / Atomic weight of copper / Number of free electrons per atom Density of copper is the mass of copper per unit volume, which is given by mass/volume.
The mass of copper in the rod is given by volume × density, which is (πr²L) × 8.96 × 10³ kg/m³.Number of free electrons per atom is 1 because each copper atom has one free electron. Plugging in the values, MFP = (ρL / A) × (A / n)MFP = (ρL / n)Substituting the values we get, MFP = (1 × 10⁻⁸ × 1) / (8.96 × 10³ / 63.55 / 1) = 1.17 × 10⁻⁵ m.
Learn more about mean free path:
https://brainly.com/question/13019320
#SPJ11
If the screen was 30 cm behind the fish, what was the distance spanned by the diffraction spot as it moved back and forth? The screen was in the tank with the fish, so that the entire path of the laser was in water and tissue with an index of refraction close to that of water. The properties of the diffraction pattern were thus determined by the wavelength in water.
Express your answer with the appropriate units
To determine the distance spanned by the diffraction spot, we need to consider the properties of the diffraction pattern and the given information.
Given:
- The screen is 30 cm behind the fish.
- The entire path of the laser, including the water and tissue, has an index of refraction close to that of water.
- The properties of the diffraction pattern are determined by the wavelength in water.
Since the diffraction pattern is formed by the interaction of light waves with obstacles or apertures, the spot's size or spread depends on factors such as the wavelength of light and the size of the aperture.
Without specific information about the wavelength or aperture size, it is not possible to determine the exact distance spanned by the diffraction spot. Additional details regarding the specific setup or measurements would be necessary to calculate or estimate the distance spanned by the diffraction spot.
Please provide further information or clarify the parameters related to the diffraction setup if you require a more specific answer.
Learn more about diffraction spot
brainly.com/question/30047488
#SPJ11
A 28000 kg monument is being used in a tug of war between Superman, Heracles, and Mr. H. The monument starts moving to the left. Heracles is pulling with a force of 15,000 N [Left]. Superman is pulling the same monument with a force of 15,000 N [Left45oUp]. Mr. Howland is pulling the same monument with a force of 1000 N [Right]. The force of kinetic friction between the monument and ground is 1500 N. What is the net force on the monument?
A 28000 kg monument is being used in a tug of war between the net force on the monument is approximately -27,607 N (to the left).
Superman, Heracles, and Mr. HTo find the net force on the monument, we need to consider the individual forces acting on it and their directions.
The forces acting on the monument are as follows:
1. Heracles: 15,000 N to the left.
2. Superman: 15,000 N at an angle of 45 degrees above the left.
3. Mr. Howland: 1000 N to the right.
4. Kinetic friction: 1500 N to the left (opposing the motion).
Since the monument is moving to the left, we will consider leftward forces as negative and rightward forces as positive.
Calculating the horizontal components of the forces:
1. Heracles: 15,000 N (leftward) has a horizontal component of -15,000 N.
2. Superman: The force of 15,000 N at an angle of 45 degrees can be resolved into horizontal and vertical components. The horizontal component is -15,000 N * cos(45°) = -10,607 N.
3. Mr. Howland: 1000 N (rightward) has a horizontal component of +1000 N.
Now, let's find the net horizontal force:
Net force = (-15,000 N) + (-10,607 N) + (+1000 N) + (-1500 N)
Simplifying the equation:
Net force = -26,107 N - 1500 N
Net force ≈ -27,607 N
The negative sign indicates that the net force is in the leftward direction.
Therefore, the net force on the monument is approximately -27,607 N (to the left).
Learn more about net force here:
https://brainly.com/question/18031889
#SPJ11
An overhead East-West transmission line carries a current of 250. A in each of two parallel wires. The two wires are separated by 1.20 m, the northern wire carries current to the east, and the southern wire carries current to the west. (a) Please find the magnitude and the direction of the magnetic field at a point midway between the two wires. (Ignore the carth's magnetic field.) (b) Please find the magnitude and the direction of the magnetic field at a point that is 2.00 m below the point of part (a). (lgnore the earth's magnetic field.)
Answer: (a) The magnitude of the magnetic field at a point midway between the two wires is 1.20 × 10⁻⁵ T and the direction of the magnetic field is out of the page.
(b) The magnitude of the magnetic field at a point that is 2.00 m below the point of part (a) is 2.93 × 10⁻⁷ T and the direction of the magnetic field is out of the page.
(a) The magnitude of the magnetic field at a point midway between the two wires is 1.20 × 10⁻⁵ T and the direction of the magnetic field is out of the page. Between two parallel current-carrying wires, the magnetic field has a direction that is perpendicular to both the direction of current flow and the direction that connects the two wires.
According to the right-hand rule, we can figure out the direction of the magnetic field. The right-hand rule says that if you point your thumb in the direction of the current and curl your fingers, your fingers point in the direction of the magnetic field. As a result, the northern wire's magnetic field is directed up, while the southern wire's magnetic field is directed down. Since the two magnetic fields have the same magnitude, they cancel each other out in the horizontal direction.
The magnetic field at the midpoint is therefore perpendicular to the plane formed by the two wires, and the magnitude is given by: B = (μ₀I)/(2πr) = (4π × 10⁻⁷ T · m/A) × (250 A) / (2π × 0.600 m) = 1.20 × 10⁻⁵ T.
The magnetic field is out of the page because the two magnetic fields are in opposite directions and cancel out in the horizontal direction.
(b) The magnitude of the magnetic field at a point that is 2.00 m below the point of part (a) is 2.93 × 10⁻⁷ T and the direction of the magnetic field is out of the page.
The magnetic field at a point that is 2.00 m below the midpoint is required. The magnetic field is inversely proportional to the square of the distance from the wires.
Therefore, the magnetic field at this point is given by: B = (μ₀I)/(2πr) = (4π × 10⁻⁷ T · m/A) × (250 A) / (2π × √(1.20² + 2²) m) = 2.93 × 10⁻⁷ T. The magnetic field at this point is out of the page since the wires are so far apart that they can be treated as two separate current sources. The field has the same magnitude as the field created by a single wire carrying a current of 250 A and located 1.20 m away.
Learn more about magnetic field : https://brainly.com/question/7645789
#SPJ11
Drag each label to the correct location on the table. Sort the sentences based on whether they describe radio waves, visible light waves, or both. They have colors. They can travel in a vacuum. They have energy. They’re used to learn about dust and gas clouds. They’re used to find the temperature of stars. They’re invisible.
Based on the given sentences, let's sort them into the correct categories: radio waves, visible light waves, or both.
Radio waves:
- They're used to learn about dust and gas clouds.
Visible light waves:
- They have colors.
- They're used to find the temperature of stars.
Both radio waves and visible light waves:
- They can travel in a vacuum.
- They have energy.
- They're invisible.
Sorted table:
| Radio Waves | Visible Light Waves | Both |
|----------------------|----------------------|----------------------|
| They're used to learn about dust and gas clouds. | They have colors. | They can travel in a vacuum. |
| - | They're used to find the temperature of stars. | They have energy. |
| - | - | They're invisible. |
Learn more in light waves
brainly.com/question/3091095
#SPJ11
(b) Estimate the pressure on the mountains underneath the Antarctic ice sheet, which is typically 3 km thick. (Density of ice = 917 kg/m³, g = 9.8 m/s²) Pressure 9170009
The estimated pressure on the mountains underneath the Antarctic ice sheet is approximately 26,854,200 N/m². To estimate the pressure on the mountains underneath the Antarctic ice sheet, we can use the formula for pressure:
Pressure = Density * g * Depth
Given:
Density of ice (ρ) = 917 kg/m³
Acceleration due to gravity (g) = 9.8 m/s²
Depth of the ice sheet (h) = 3 km = 3000 m
Plugging in these values into the formula, we get:
Pressure = 917 kg/m³ * 9.8 m/s² * 3000 m
= 26,854,200 N/m²
Therefore, the estimated pressure on the mountains underneath the Antarctic ice sheet is approximately 26,854,200 N/m².
To know more about Acceleration
brainly.com/question/31946450
#SPJ11
marbles rolling down the ramp and horizontally off your desk consistently land 48.0 cm from the base of your desk. ypur desk is 84.0 cm high. if you pull your desk over to the window of your second story room and launch marbles to the ground (6.56 meters below the desk top), how far out into the yard will the marbles land?
The marbles will land approximately 0.479 meters, or 47.9 centimeters, out into the yard.
To determine how far the marbles will land in the yard, we can use the principle of projectile motion. Since the marble is launched horizontally, its initial vertical velocity is 0 m/s.
We can use the following kinematic equation to find the horizontal distance traveled by the marble:
d = v_x * t
where:
d is the horizontal distance traveled,
v_x is the horizontal velocity of the marble, and
t is the time of flight.
First, let's calculate the time of flight. We can use the equation for vertical displacement in free fall:
y = (1/2) * g * t^2
where:
y is the vertical displacement,
g is the acceleration due to gravity (approximately 9.8 m/s^2), and
t is the time of flight.
Given that the vertical displacement is 6.56 meters, we can rearrange the equation to solve for time:
t = sqrt(2y/g)
t = sqrt(2 * 6.56 / 9.8)
t ≈ 1.028 seconds
Now, let's calculate the horizontal velocity. Since there is no horizontal acceleration, the horizontal velocity remains constant throughout the motion. We can use the horizontal distance traveled on the desk (48.0 cm = 0.48 meters) and the time of flight to find the horizontal velocity:
d = v_x * t
0.48 = v_x * 1.028
v_x ≈ 0.466 m/s
Finally, we can calculate the horizontal distance the marble will travel to the ground (in the yard) using the horizontal velocity and the time of flight:
d = v_x * t
d = 0.466 * 1.028
d ≈ 0.479 meters
Therefore, the marbles will land approximately 0.479 meters, or 47.9 centimeters, out into the yard.
Learn more about vertical velocity
https://brainly.com/question/29026497
#SPJ11
Use your result above to calculate the incident angle θ 1
from air in entering the fiber (see notes on refraction). Use three significant digits please.
To calculate the incident angle θ1, we need additional information related to refraction, such as the refractive indices of the materials involved.
In the context of refraction, the incident angle (θ1) is the angle between the incident ray and the normal to the interface between two media. To calculate θ1, we need to know the refractive indices of the materials involved. The refractive index (n) is a property of a medium that determines how light propagates through it. The relationship between the incident angle, the refractive indices of the two media, and the angles of refraction can be described by Snell's law.
To determine the incident angle accurately, the refractive indices of both the air and the fiber are required. Once these values are known, Snell's law can be applied to calculate the incident angle.
Learn more about refraction here:
https://brainly.com/question/14760207
#SPJ11
The voltage (in Volts) across an element is given as v(t) = 50 cos (6ft + 23.5°) whereas the current (in Amps) through the element is i(t) = -20 sin (6ft +61.2°); where time, t is the time and f is the frequency in seconds and Hertz respectively.
Determine the phase angle between the two harmonic functions.
The voltage and current functions are v(t) = 50 cos (6ft + 23.5°) and i(t) = -20 sin (6ft +61.2°), respectively. The phase angle between them is 0.66 radians or 37.8 degrees.
To determine the phase angle between the voltage and current functions, we need to find the phase difference between the cosine and sine functions that represent them.
The general form of a cosine function is given by:
cos(wt + theta)
where w is the angular frequency in radians per second, t is time in seconds, and theta is the initial phase angle in radians.
Similarly, the general form of a sine function is given by:
sin(wt + theta)
where w is the angular frequency in radians per second, t is time in seconds, and theta is the initial phase angle in radians.
Comparing the given functions for voltage and current with these general forms, we can see that the angular frequency is the same for both, and is equal to 6f radians per second. The phase angle for the voltage function is 23.5 degrees, or 0.41 radians, while the phase angle for the current function is 61.2 degrees, or 1.07 radians.
The phase difference between the two functions is given by the absolute difference between their phase angles, which is:
|0.41 - 1.07| = 0.66 radians
Therefore, the phase angle between the voltage and current functions is 0.66 radians, or approximately 37.8 degrees.
To know more about voltage and current functions, visit:
brainly.com/question/31478615
#SPJ11
Maximum Kinetic Enegy Of The Photoelectron Emitted Is:A)6.72 X 10^-18Jb) 4.29 Jc) 2.63 X 10^19Jd) 3.81 X 10^-20J
if the stopping potential of a photocell is 4.20V, then the maximum kinetic enegy of the photoelectron emitted is:
a)6.72 x 10^-18J
b) 4.29 J
c) 2.63 x 10^19J
d) 3.81 x 10^-20J
The maximum kinetic energy of the photoelectron emitted from a photocell with a stopping potential of 4.20V is 6.72 x 10^-19J.
This value is obtained by using the relationship between energy, charge, and voltage. The photoelectric effect, which describes this phenomenon, illustrates how energy is transferred from photons to electrons. The stopping potential (V) is the minimum voltage needed to stop the highest energy electrons that are emitted. Therefore, the maximum kinetic energy (K.E) of an electron can be calculated using the equation K.E = eV, where e is the charge of an electron (approximately 1.60 x 10^-19 coulombs). Substituting the given values, K.E = 1.60 x 10^-19 C * 4.20 V = 6.72 x 10^-19 J. Hence, option a) is the correct answer.
Learn more about the photoelectric effect here:
https://brainly.com/question/9260704
#SPJ11
A long nonconducting cylinder (radius =10 cm) has a charge of uniform density (6.0nC/m 3
) distributed throughout its column. Determine the magnitude of the electric field 2.5 cm from the axis of the cylinder.
To determine the magnitude of the electric field at a distance of 2.5 cm from the axis of the cylinder. The magnitude of the electric field at a distance of 2.5 cm from the axis of the cylinder is approximately 135,453 N/C.
Radius of the cylinder (r) = 10 cm = 0.1 m Charge density (ρ) = 6.0 nC/m³ Distance from the axis (d) = 2.5 cm = 0.025 m To calculate the electric field, we can use the formula: Electric field (E) = (ρ * r) / (2 * ε₀ * d) Where ε₀ is the permittivity of free space.
Substituting the given values and the constant value of ε₀ (8.854 x 10^-12 C²/(N·m²)) into the formula, we can calculate the magnitude of the electric field. Electric field (E) = (6.0 nC/m³ * 0.1 m) / (2 * 8.854 x 10^-12 C²/(N·m²) * 0.025 m) Calculating the expression: Electric field (E) ≈ 135,453 N/C
Learn more about electric field here:
https://brainly.com/question/11482745
#SPJ11