A 1 m diameter pipe 1400 m long. Q = 600 L/s Compute head loss if n = 0.015

Answer: death if you get covid 19 in cotabato you will have ti see a doctor and the ramifications are sneesing coughing and throwing up and loss of sleep

Step-by-step explanation:

Answer:

[tex]x = 5\sqrt3[/tex]

Step-by-step explanation:

We can solve for x in this right triangle by using the ratio of the sides in a 30-60-90 triangle:

We can identify the longest side, or hypotenuse (which corresponds to 2 in the ratio), as 10. We can also see that the second largest side (√3 in the ratio) is x.

Therefore, to solve for x, we can multiply 10 by [tex]\dfrac{\sqrt3}{2}[/tex] because that is the number which gets 2 to [tex]\sqrt3[/tex]:

[tex]\not2 \cdot \dfrac{\sqrt3}{\not2} = \sqrt3[/tex]

[tex]x = 10 \cdot \dfrac{\sqrt3}{2}[/tex]

[tex]\boxed{x = 5\sqrt3}[/tex]

The fraction of an inch that would equal this is 1/3 inches.

Building codes usually specify that deflection (bending downward at the center) in a floor joist for residential buildings should not exceed 1/360 of the span under normal loads.

What fraction of an inch would this equal for a span of 10'-0"?

The maximum allowable deflection for a floor joist is defined in the building codes as 1/360 of the span under normal loads.

A 10'-0" span is given in the problem.

1/360 of a 10'-0" span will be calculated below.

We know that 1/360 = x/120.

The cross-multiply method will be used to solve the equation.

360x = 120x 1 = 3x x = 1/3 inches is the answer.

Therefore, the fraction of an inch that would equal this is 1/3 inches.

To know more about fraction visit:

https://brainly.com/question/10354322

#SPJ11

Answer:

Domain: {0, 1, 2, 3)

Range: {4, 5, 6.25, 7.8125}

Step-by-step explanation:

Domain is the x value going right or left.

Range is the y value going up or down.

Horizontal line = --------

Vertical line = I

The torque required to cause a shearing stress of 40 MPa in the thin-walled tube is approximately 25.13 Nm. To calculate the torque, we need to consider the shearing stress acting on the wall of the semi-circular tube.

The shearing stress can be calculated using the formula:

τ = (T * r) / (J * t)

Where:

τ = Shearing stress

T = Torque

r = Mean radius of the tube (half the diameter)

J = Polar moment of inertia of the tube cross-section

t = Wall thickness

Since the stress concentration at the corners is neglected, we can consider the tube as a thin-walled circular tube. The polar moment of inertia for a thin-walled circular tube is given by:

J = (π * (D^4 - d^4)) / 32

Where:

D = Outer diameter of the tube

d = Inner diameter of the tube

Given:

Mean diameter (D) = 50 mm

Wall thickness (t) = 6 mm

Shearing stress (τ) = 40 MPa

calculating  the inner diameter:

d = D - 2t = 50 mm - 2 * 6 mm = 38 mm

Next, we can calculate the mean radius:

r = D / 2 = 50 mm / 2 = 25 mm

the polar moment of inertia:

J = (π * (D^4 - d^4)) / 32 = (π * ((50 mm)^4 - (38 mm)^4)) / 32 ≈ 2.43e7 mm^4

Finally, rearranging the shearing stress formula to solve for torque: T = (τ * J * t) / r = (40 MPa * 2.43e7 mm^4 * 6 mm) / 25 mm ≈ 25.13 Nm . The torque required to cause a shearing stress of 40 MPa in the thin-walled tube is approximately 25.13 Nm.

To know more about  torque visit:

https://brainly.com/question/30338175

#SPJ11

1. To determine the optimal number of boxes to make using the Single Period Inventory Excel template in MindTap, we need to consider the costs and revenues associated with producing and selling the boxes.

- The cost per box, including material and labor, is $13.
- The selling price per box before Valentine's Day is $28.
- After Valentine's Day, the price is reduced to $12.
- Suzie has historically sold between 55 and 100 boxes.

To find the optimal number of boxes to make, we can use the Single Period Inventory Excel template in MindTap. This template takes into account the costs and revenues and helps us determine the quantity that maximizes profit.

2. If Suzie can only sell all remaining boxes at a price of $4, her decision would change because the selling price is significantly lower. This means that the revenue generated from selling the remaining boxes would be lower, affecting the overall profit.

In this case, Suzie would need to consider whether it is still profitable to produce the same number of boxes or if she should produce a smaller quantity. By using the Single Period Inventory Excel template in MindTap with the new selling price of $4, she can calculate the optimal number of boxes to make.

It's important to note that the optimal number of boxes may change based on the selling price, as it directly affects the revenue generated. Suzie should carefully evaluate the costs and revenues associated with different scenarios to make an informed decision.

Overall, the Single Period Inventory Excel template in MindTap is a useful tool for determining the optimal number of boxes to make, taking into account the costs, revenues, and various scenarios.

Learn more about Single Period Inventory

https://brainly.com/question/33717572

#SPJ11

Answer:

2/3

Step-by-step explanation:

To find the value of k, we can use the given information that y is 6 when x is 72. Plugging these values into the equation, we have:

6 = k * 72

To solve for k, we divide both sides of the equation by 72:

k = 6/72 = 1/12

Now that we know the value of k, we can use it to find the value of y when x is 8. Plugging x = 8 into the equation y = kx, we have:

y = (1/12) * 8 = 8/12 = 2/3

Therefore, when x is 8, y is 2/3.

When nitrous acid (HNO2) is hydrolyzed by water (H2O), the resulting products are the nitrite anion (NO2−) and hydronium ion (H3O+).

The hydrolysis reaction of nitrous acid (HNO2) is given by the following equation:HNO2(aq) + H2O(l) ⇌ NO2−(aq) + H3O+(aq). Thus, nitrous acid reacts with water to form nitrite ion and hydronium ion, represented by the following formulas:

.

Thus, nitrous acid reacts with water to form nitrite ion and hydronium ion, represented by the following formulas: Reactants: HNO2(aq) + H2O(l)Products: NO2−(aq) + H3O+(aq)

To know more about acid visit :

https://brainly.com/question/29796621

#SPJ11

Answer:

B. It is a line segment

C. It is a two-dimensional object

Step-by-step explanation:

A line segment is a part of a straight line that is bounded by two distinct end points, and contains every point on the line that is between its endpoints.

A triangle is a two-dimensional shape, in Euclidean geometry, which is seen as three non-collinear points in a unique plane.

The concentration of the product when the degree of conversion is 0.8 depends on the specific rate constant and the stoichiometry of the reaction.

In a first-order reversible reaction, the rate of reaction is proportional to the concentration of the reactant raised to the power of its order. In this case, the reaction is first order with respect to both A and B. The rate law for the forward reaction can be expressed as:

Rate = k1 * [A] * [B]

Since the reaction is reversible, there is also a reverse reaction with its own rate constant, k2. The rate law for the reverse reaction can be expressed as:

Rate_reverse = k2 * [product]

The degree of conversion, ξ, is defined as the fraction of A that has reacted. In this case, the initial moles of A and B are both 200, so the total initial moles is 400. If the degree of conversion is 0.8, it means that 80% of A has reacted, leaving 20% unreacted.

To determine the concentration of the product when ξ = 0.8, we need to consider the stoichiometry of the reaction. From the balanced equation, we can see that for every two moles of A that react, one mole of product is formed. Therefore, if 80% of A has reacted, the concentration of the product would be 40% of the initial concentration of A and B.

In summary, when the degree of conversion is 0.8, the concentration of the product would be 40% of the initial concentration of A and B. This is based on the stoichiometry of the reaction and the assumption that the reaction follows first-order kinetics with respect to both A and B.

Learn more about Stoichiometry

brainly.com/question/28780091

#SPJ11

The empirical formula of the compound is CCl3.

To determine the empirical formula of the compound based on the given percentages, we need to convert the percentages to moles and find the simplest whole number ratio between the elements.

Assume we have a 100g sample of the compound. This means we have 7.808g of carbon and 92.19g of chlorine.

Convert the masses to moles using the molar masses of carbon (C) and chlorine (Cl).

Moles of C = 7.808g C / molar mass of C

Moles of Cl = 92.19g Cl / molar mass of Cl

Divide the number of moles by the smallest number of moles to obtain the mole ratio.

Mole ratio of C : Cl = Moles of C / Smallest number of moles

Mole ratio of C : Cl = Moles of Cl / Smallest number of moles

Find the simplest whole number ratio by multiplying the mole ratio by the appropriate factor to obtain whole numbers.

The resulting whole number ratio represents the empirical formula of the compound.

To know more about empirical formula, visit:

https://brainly.com/question/9238941

#SPJ11

Answer:

B

Step-by-step explanation:

hope this helps :)

The triangle is an equilateral triangle and it is an acute triangle

From the question, we have the following parameters that can be used in our computation:

The triangle

From the figure, we can see that

The three lengths of triangle are congruent

This means that the triangle is an equilateral triangle

Also, we can see that

All angles in the triangle are less than 90

This means that the triangle is an acute triangle

Read more about triangle at

brainly.com/question/10025467

#SPJ1

The commons in the tragedy of the commons situation described is the ground outside the university classroom building where smokers throw their cigarette butts instead of using proper receptacles.

This leads to the need for maintenance staff to clean up the area. The insufficient funds then prevent the classrooms in the building from being equipped with whiteboard markers and erasers. Therefore, option A, the ground outside the building, represents the commons in this scenario.

In the case of the woodlot shared by four families, the sustainable production is 300 mature mushrooms per month, each valued at $2. However, if more mushrooms are harvested, only immature mushrooms are available, and their value is determined by the formula $21,300 divided by the total number of mushrooms harvested. One family has been secretly taking 85 mushrooms per month for several months. To determine the value of their harvest, we need to calculate the total number of mushrooms they took and then substitute it into the value formula. Assuming they took 85 mushrooms per month for a certain number of months, we can multiply 85 by the number of months to obtain the total number of mushrooms taken. Let's say they took 85 mushrooms for 5 months, then the total number of mushrooms taken would be 85 × 5 = 425. Substituting this value into the formula, we get $21,300/425 = $50. Therefore, the value of their harvest would be $50.

To learn more about receptacles refer:

https://brainly.com/question/2284051

#SPJ11

The energy of a photon with a wavelength of 5.84 mm is  9.997 x 10^-23 J.

The energy of a photon can be calculated using the equation E = hc/λ, where E is the energy of the photon, h is Planck's constant, c is the speed of light, and λ is the wavelength of the photon.

In this case, the given wavelength is 5.84 mm. To use the equation, we need to convert the wavelength to meters.

1 mm = 0.001 m

So, the wavelength in meters is 5.84 mm x 0.001 m/mm = 0.00584 m.

Now we can calculate the energy of the photon using the equation E = hc/λ.

h = 6.626 x 10^-34 J·s (Planck's constant)
c = 3 x 10^8 m/s (speed of light)
λ = 0.00584 m (wavelength)

Plugging these values into the equation, we get:

E = (6.626 x 10^-34 J·s) * (3 x 10^8 m/s) / (0.00584 m)
 = (6.626 x 3 x 10^-34 x 10^8) J / 0.00584
 = (19.878 x 10^-26) J / 0.00584
 = 3405.4 x 10^-26 J / 0.00584
 = 583708.9 x 10^-26 J / 0.00584
 = 9.997 x 10^-23 J

Therefore, the energy of a photon with a wavelength of 5.84 mm is approximately 9.997 x 10^-23 J.

To learn more about energy of a photon visit : https://brainly.com/question/15946945

#SPJ11

The molarity after dilution is approximately 0.02016 M

To find the resulting molarity (M) after dilution, we can use the equation:

M₁V₁ = M₂V₂

Where:

M₁ = initial molarity

V₁ = initial volume

M₂ = resulting molarity

V₂ = resulting volume

In this case:

M₁ = 0.224 M

V₁ = 0.90 mL = 0.90 cm³

M₂ = ?

V₂ = 10.00 mL = 10.00 cm³

Plugging in the values into the equation, we get:

(0.224 M)(0.90 cm³) = (M₂)(10.00 cm³)

Rearranging the equation to solve for M₂:

M₂ = (0.224 M)(0.90 cm³) / (10.00 cm³)

Calculating the value, we find:

M₂ = 0.02016 M

Therefore, the resulting molarity after dilution is approximately 0.02016 M.

To know more about molarity, visit:

https://brainly.com/question/32029576

#SPJ11

In the context of construction contracts, quality refers to the level of excellence or conformance to specifications of the construction project. It is not just about meeting the minimum requirements but exceeding them to achieve a higher degree of excellence.

Quality can be assessed through various measures, such as durability, performance, functionality, and aesthetics.

Option a: Conformance to specifications refers to the extent to which the construction project meets the specified requirements. This includes factors like materials used, dimensions, and other technical specifications. It ensures that the project is built according to the agreed-upon plans and designs.

Option b: A measure of goodness can be interpreted as a subjective assessment of the construction project. Goodness can refer to how well the project satisfies the client's expectations and requirements. However, in the context of construction contracts, it is more common to use objective measures like conformance to specifications.

Option c: A degree of excellence is a broader concept that encompasses not only meeting the specifications but also surpassing them. It involves achieving high standards in terms of performance, aesthetics, and functionality. The level of excellence can vary depending on the project's requirements and the client's expectations.

Option d: Durability is an important aspect of quality in construction. It refers to the ability of the project to withstand the test of time and perform well over its expected lifespan. Durability is influenced by factors like the quality of materials used, construction techniques, and maintenance practices. A durable construction project is less likely to require frequent repairs or replacements.

In summary, quality in construction contracts is about achieving a high level of excellence and conformance to specifications. It involves meeting the agreed-upon requirements, including factors like durability, performance, functionality, and aesthetics.

Durability is one of the key aspects of quality, ensuring the long-term performance and reliability of the construction project.

Learn more about durability from the link:

https://brainly.com/question/32050630

#SPJ11

The diffusive flux of methylene chloride through the glove is [tex]-0.22 g/cm^2-s.[/tex]. This indicates that some methylene chloride can pass through the glove and should be handled with caution.

The diffusive flux of methylene chloride through the glove can be determined by using Fick's first law of diffusion, which relates the diffusive flux of a species through a medium to its concentration gradient and diffusivity. The equation for Fick's law is given by J = -D(dc/dx), where J is the diffusive flux, D is the diffusion coefficient, and dc/dx is the concentration gradient.

For this problem, the diffusive flux of methylene chloride through the butyl rubber glove can be calculated as follows:

J = -D(dc/dx)

=[tex]-110 x 10^-8 cm^2/s x (0.44 - 0.02) g/cm^3 / (0.08 cm)[/tex]

= -0[tex].22 g/cm^2-s[/tex]

Therefore, the diffusive flux of methylene chloride through the glove is[tex]-0.22 g/cm^2-s.[/tex]

This indicates that some methylene chloride can pass through the glove and should be handled with caution.

:Therefore, the diffusive flux of methylene chloride through the glove is [tex]-0.22 g/cm^2-s.[/tex]. This indicates that some methylene chloride can pass through the glove and should be handled with caution.

To know more about methylene chloride visit:

brainly.com/question/30897787

#SPJ11

The formula for the nth term (an) of the arithmetic sequence is:

an = 2.7 - 0.2n

The formula for the nth term (an) of an arithmetic sequence is:

an = a1 + (n-1)d

where a1 is the first term, d is the common difference, and n is the term number.

Using the given values, we have:

a1 = 2.5

d = -0.2

Substituting these values into the formula, we get:

an = 2.5 + (n-1)(-0.2)

Simplifying this expression, we get:

an = 2.7 - 0.2n

Therefore, the formula for the nth term (an) of the arithmetic sequence is:

an = 2.7 - 0.2n

Learn more about  arithmetic sequence from

https://brainly.com/question/6561461

#SPJ11

a. To find the present value at t=10, we need to calculate the value of f(t) at t=10. Using the given function f(t) = 500e^(0.04t), we substitute t=10 into the equation:

[tex]\displaystyle \text{Present value} = f(10) = 500e^{0.04(10)}[/tex]

Simplifying the exponent:

[tex]\displaystyle \text{Present value} = 500e^{0.4}[/tex]

Evaluating the exponent:

[tex]\displaystyle \text{Present value} = 500(2.71828^{0.4})[/tex]

Calculating the value inside the parentheses:

[tex]\displaystyle \text{Present value} = 500(1.49182)[/tex]

Calculating the product:

[tex]\displaystyle \text{Present value} \approx 745.91[/tex]

Therefore, the present value at t=10 is approximately $745.91.

b. To find the accumulated money flow at t=10, we need to calculate the integral of f(t) from 0 to 10. Using the given function f(t) = 500e^(0.04t), we integrate the function with respect to t:

[tex]\displaystyle \text{Accumulated money flow} = \int_{0}^{10} 500e^{0.04t} dt[/tex]

Integrating:

[tex]\displaystyle \text{Accumulated money flow} = 500 \int_{0}^{10} e^{0.04t} dt[/tex]

Using the properties of exponential functions, we can evaluate the integral:

[tex]\displaystyle \text{Accumulated money flow} = 500 \left[ \frac{{e^{0.04t}}}{{0.04}} \right]_{0}^{10}[/tex]

Simplifying:

[tex]\displaystyle \text{Accumulated money flow} = 500 \left( \frac{{e^{0.4}}}{{0.04}} - \frac{{e^{0}}}{{0.04}} \right)[/tex]

Calculating the exponential terms:

[tex]\displaystyle \text{Accumulated money flow} = 500 \left( \frac{{e^{0.4}}}{{0.04}} - \frac{1}{{0.04}} \right)[/tex]

Evaluating the exponential term:

[tex]\displaystyle \text{Accumulated money flow} = 500 \left( \frac{{1.49182}}{{0.04}} - \frac{1}{{0.04}} \right)[/tex]

Calculating the subtraction:

[tex]\displaystyle \text{Accumulated money flow} = 500 \left( \frac{{1.49182 - 1}}{{0.04}} \right)[/tex]

Calculating the division:

[tex]\displaystyle \text{Accumulated money flow} = 500 \times 12.2955[/tex]

Calculating the product:

[tex]\displaystyle \text{Accumulated money flow} \approx 6147.75[/tex]

Therefore, the accumulated money flow at t=10 is approximately $6147.75.

[tex]\huge{\mathfrak{\colorbox{black}{\textcolor{lime}{I\:hope\:this\:helps\:!\:\:}}}}[/tex]

♥️ [tex]\large{\underline{\textcolor{red}{\mathcal{SUMIT\:\:ROY\:\:(:\:\:}}}}[/tex]

0.0700 moles of aluminum participated in the chemical reaction.The stoichiometry states that in a chemical reaction, the reactants and products have a specific relationship between their molar ratios.

Stoichiometry is a section of chemistry that deals with calculating the proportions in which elements or compounds react. It is used to determine the amounts of substances consumed and produced in a chemical reaction. By comparing reactants' coefficients with product coefficients, stoichiometry uses quantitative measurements to determine the number of moles in a chemical reaction.

In this given question, we are supposed to determine the moles of aluminum that participated in the reaction. The number of moles of aluminum can be determined by the mole-to-mole ratio of the chemical reaction. For this, we must first write the balanced chemical reaction. Aluminum reacts with oxygen gas to form aluminum oxide.4Al + 3O2 → 2Al2O3.

The mole ratio of aluminum to aluminum oxide in the chemical reaction is 4:2 or 2:1. This means that for every 2 moles of aluminum oxide, there are 4 moles of aluminum.Using the mole-to-mole ratio, we can determine the number of moles of aluminum.0.0350 moles of aluminum is given in the problem.

Using the mole-to-mole ratio,2 moles of Al2O3 = 4 moles of Al0.0350 moles of Al2O3

= (4/2) × 0.0350 moles of Al

= 0.0700 moles of Al.

Therefore, 0.0700 moles of aluminum participated in the chemical reaction.

To know more about mole ratio visit-

brainly.com/question/14425689

#SPJ11

The number of ideal stages required to carry out the desired extraction is 2.

Given:

Quantity of lycopene produced by each gram of dry fungus = 0.15 g

Feed (dry fungus) introduced into the extractor = 10 kg

Economic considerations dictate a solvent to feed ratio of 1:1

Each gram of lycopene-free fungus tissue retains 0.6 g of liquid

Laboratory tests have indicated that each gram of lycopene-free fungus tissue retains 0.6 g of liquid, regardless of the concentration of lycopene in the extract.

Initial feed = 10 kg

Amount of liquid in the feed = 0.6 kg/kg of lycopene-free fungus tissue

Total mass in the extractor = 10 + 0.6(10) = 16 kg

Total solvent to be added = 1:1 solvent to feed ratio = 10 kg

The mass of solvent in the extractor = 8 kg

The mass of lycopene in the feed = 0.15(10) = 1.5 kg

Concentration of lycopene in the feed = 1.5/10 = 0.15 kg/kg of mixture

Mass of lycopene to be extracted = 0.9(1.5) = 1.35 kg

Mass of lycopene to remain in the residue = 0.15 kg

Mass of solvent required to extract 1 kg of lycopene = 1 kg

Therefore, the mass of solvent required to extract 1.35 kg of lycopene = 1.35 kg

The mass of solvent required to extract 1 kg of lycopene from the residue = 1 kg

The mass of residue after the extraction of 1.35 kg of lycopene

= 10 + 0.6(10) – 1.35 – 8

= 0.25 kg

Concentration of lycopene in the final overflow;ya

The total mass of the final overflow

= 1.35 + 8

= 9.35 kg

Concentration of lycopene in the final overflow

= 1.35/9.35

= 0.144 kg/kg of the mixture (3 s.f.)

The expected composition of the underflow solution (content of lycopene %w/w in the solution)

The total mass of underflow = 0.25 kg

Concentration of lycopene in the underflow = 0.15/0.25

= 0.6 kg/kg of the mixture

%w/w of lycopene in the underflow = 0.6/2.5 × 100

= 24%

Number of ideal stages required to carry out the desired extraction:

Using the slope of the equilibrium curve for hexane/methanol/lycopene at 30°C and total pressure of 1 atm, the number of ideal stages required to carry out the extraction can be determined as:

Δx/Δy = (L/D)(H/L’)

The equilibrium line equation is

y = 0.107x + 0.005,

where y is the mass fraction of lycopene in the solvent, and

x is the mass fraction of lycopene in the feed.

L = solvent flow rate = feed flow rate

= D

= 10 kg/hrL’

= the mass of lycopene in the solvent stream divided by the mass of lycopene-free solvent (from the equilibrium curve)

For y = 0.144,

x = 0.15

Δx = (0.15 – 0.144) = 0.006

Δy = (0.107(0.15) + 0.005 – 0.144)

= 0.00865(H/L’)

= Δx/Δy = (0.006/0.00865)

= 0.694

Therefore, the number of ideal stages required to carry out the desired extraction is given by:

N = log10 (H/L’) / log10 (1 + L/D)

N = log10(0.694) / log10 (1 + 1)

= 0.342 / 0.301

= 1.14 ≈ 2 stages (to the nearest whole number).

Thus, the solution is,The concentration of lycopene in the final overflow = 0.144 kg/kg.

The expected composition of the underflow solution (content of lycopene %w/w in the solution) = 24%.

The number of ideal stages required to carry out the desired extraction = 2.

To know more about lycopene visit :

brainly.com/question/30331882

#SPJ11

Answer: Employee Provident Fund Organization (EPFO), one of the largest social security organisations in the world, is in charge of managing the welfare programme known as Employee Provident Fund (EPF). Employees should be informed of the tax regulations regarding investments, accruals, and EPF withdrawals.

Step-by-step explanation:

To determine the route traffic flows, we need to calculate the travel costs, incremental costs, incremental probabilities, and then use these values to calculate the traffic flows for each route.

One OD pair has 2 routes connecting them. The total demand is 1000 veh/hr. The first route has a travel time function as t₁ = 10 + 0.03V₁, and the second route has a travel time function as t₂ = 12 + 0.05V₂, where V₁ and V₂ are the traffic volumes on route 1 and 2. It is important to note that V₁ + V₂ = 1000 veh/hr.To determine the route traffic flows, we will use incremental assignment with the given probabilities: p₁ = 0.4, p₂ = 0.3, p₃ = 0.2, and p₄ = 0.1.
Step 1: Calculate the travel costs for each route.
- For route 1: t₁ = 10 + 0.03V₁
- For route 2: t₂ = 12 + 0.05V₂
Step 2: Determine the incremental costs for each route.
- Incremental cost for route 1: ΔC₁ = t₁ - t₂ = (10 + 0.03V₁) - (12 + 0.05V₂)
- Incremental cost for route 2: ΔC₂ = t₂ - t₁ = (12 + 0.05V₂) - (10 + 0.03V₁)
Step 3: Calculate the incremental probabilities for each route.
- Incremental probability for route 1: ΔP₁ = p₁ / (p₁ + p₃) = 0.4 / (0.4 + 0.2)
- Incremental probability for route 2: ΔP₂ = p₂ / (p₂ + p₄) = 0.3 / (0.3 + 0.1)
Step 4: Calculate the route traffic flows.
- Traffic flow for route 1: F₁ = ΔP₁ / ΔC₁
- Traffic flow for route 2: F₂ = ΔP₂ / ΔC₂
By substituting the values into the equations, we can calculate the traffic flows for each route. However, since we don't have specific values for V₁ and V₂, we cannot provide the exact traffic flow values.

To learn more about function

https://brainly.com/question/11624077

#SPJ11

The value of d²y/dx² at the point defined by the given value of t is, To find the value of d²y/dx² at the given point, we first need to find the first derivative dy/dx and then take its derivative with respect to x once again

Given the equations x = sin t and y = 9sin(t + 1), we can determine the value of x at the given point by substituting the value of t into the equation x = sin t. Similarly, we can find the value of y at the given point by substituting t into the equation y = 9sin(t + 1).

Next, we calculate the first derivative dy/dx by differentiating y with respect to x. This involves applying the chain rule, as y is a function of t.

Finally, we differentiate dy/dx with respect to x once again to find the second derivative d²y/dx². This requires applying the chain rule once more.

Substituting the value of t into the expression for d²y/dx², we obtain the value at the given point.

Therefore, the value of d²y/dx² at the point defined by the given value of t is (Express your answer in terms of t).

Learn more about derivative: brainly.com/question/23819325

#SPJ11

The value of d²y/dx² at the point defined by the given value of t is, To find the value of d²y/dx² at the given point, we first need to find the first derivative dy/dx and then take its derivative with respect to x once again

Given the equations x = sin t and y = 9sin(t + 1), we can determine the value of x at the given point by substituting the value of t into the equation x = sin t. Similarly, we can find the value of y at the given point by substituting t into the equation y = 9sin(t + 1).

Next, we calculate the first derivative dy/dx by differentiating y with respect to x. This involves applying the chain rule, as y is a function of t.

Finally, we differentiate dy/dx with respect to x once again to find the second derivative d²y/dx². This requires applying the chain rule once more.

Substituting the value of t into the expression for d²y/dx², we obtain the value at the given point.

Therefore, the value of d²y/dx² at the point defined by the given value of t is (Express your answer in terms of t).

Learn more about derivative: brainly.com/question/23819325

#SPJ11

In managing the global supply chains, a company shall focus on all areas. In other words, the material flow, information flow, and cash flow are important aspects that need attention in managing the global supply chains.

Supply chain management refers to the management of the flow of goods and services as well as the activities that are involved in transforming the raw materials into finished products and delivering them to customers. The process involves the integration of different parties, activities, and resources that are necessary in fulfilling the customers’ needs.

Aspects to focus on in managing the global supply chains:

Material flow: This aspect of supply chain management deals with the movement of raw materials or products from suppliers to manufacturers and finally to consumers.

In managing the global supply chains, it is important to focus on the material flow to ensure that goods are delivered to customers as required.

Information flow: The information flow aspect of supply chain management involves the transfer of information from one party to another regarding the status of the products. In managing the global supply chains, the company should focus on ensuring that the information is accurate and timely.

Cash flow: Cash flow refers to the movement of money between the parties involved in the supply chain process. In managing the global supply chains, companies should focus on ensuring that payments are made on time to avoid delays or other issues that may arise.  

Therefore in managing the global supply chains, all areas should be included.

Learn more about global supply chains

https://brainly.com/question/5115188

#SPJ11

Answer:(2x+3)(2x+3)

Step-by-step explanation:

Question will be like this Factorize the following polynomial.

4x[tex]{2}[/tex] +12x +9

4x[tex]2[/tex] +6x+6x+9

⇒2x(2x+3)+3(2x+3)

⇒(2x+3)(2x+3)

Answer:

Rule is [tex]n^2+8[/tex]

20th term is 408

Step-by-step explanation:

Notice that [tex]n^2=1,4,9,16,25,...[/tex] so if we add 8 to each term, we get [tex]n^2+8=9,12,17,24,33[/tex]. Therefore, the 20th term would be [tex]20^2+8=400+8=408[/tex]

Based on the information provided, the correct p-value is approximately 0.001 (rounded to the nearest thousandth). It appears there may have been an error in your calculation or in using the formulas in Desmos.

Note: The Desmos notation for this calculation would be:
p = 2*(1-tCDF(-3.873, 14))

To find the p-value for this hypothesis test, we need to calculate the test statistic and compare it to the appropriate distribution. The test statistic for this hypothesis test is the t-score, which is calculated using the formula:

t = (x-bar - μ) / (s / √n)

Where:
- x-bar is the sample mean (48 in this case)
- μ is the hypothesized population mean (50 in this case)
- s is the sample standard deviation (2 in this case)
- n is the sample size (15 in this case)

Substituting the given values into the formula, we get:

t = (48 - 50) / (2 / √15)
  = -2 / (2 / √15)
  = -2 / (2 / 3.873)
  = -3.873

Note: In the formula, √ represents square root.

Next, we need to determine the degrees of freedom for this test. Since we are using a t-distribution and have a sample size of 15, the degrees of freedom is given by n - 1, which is 15 - 1 = 14.

Using the t-distribution table or a statistical calculator, we can find the p-value associated with the test statistic of -3.873 and 14 degrees of freedom.

The p-value represents the probability of observing a test statistic as extreme as the one calculated, assuming the null hypothesis is true. A small p-value suggests that the observed data is unlikely to have occurred by chance alone, and provides evidence against the null hypothesis.

Based on the information provided, the correct p-value is approximately 0.001 (rounded to the nearest thousandth). It appears there may have been an error in your calculation or in using the formulas in Desmos.

Note: The Desmos notation for this calculation would be:
p = 2*(1-tCDF(-3.873, 14))

I hope this helps clarify the process of finding the p-value for a hypothesis test. If you have any further questions, feel free to ask!

To know more about the word  test statistic, visit:

https://brainly.com/question/34153666

#SPJ11